Trying to hot-clone VM with multiple snapshots

Similar Questions

• RV220W - rules of access/redirection of port with multiple WAN IP addresses

  I just installed a Cisco RV220W - that works very well for outbound traffic, however for incoming it seems unable to work with multiple WAN IP addresses.

  We have a block of 6 WAN IPs assigned to us by our ISP, and I want to use each of them to expose certain ports on our servers to the outside world.

  I tried to do with rules (by using HTTP, for example) with the following parameters:

  Connection type: Inbound (WAN (Internet) > LAN (local area network))

  Action: Always leave

  Service: HTTP

  Source IP: Unique address

  Start:

  Send to the Server Local (DNAT IP):

  Use other WAN (Internet) IP address: disabled

  Status: Activated

  However, the port of the inaccessible Server/rest.

  I tried:

  • Restart the server with power power off again
  • implement the same port forwarding settings
  • triple-checking all the IP addresses used

  The only way that I have working is by changing the access rule so that it applies to any specific source rather than to another address... but this isn't a solution for us because we need to use specific IP addresses to the internal servers/ports specific.

  The interface of the router admin certainly suggests that this should be possible, but using it seems to break all incoming access!

  Any suggestion is welcome.

  You must use "ANY" as the source IP address, you publish your internal server to the internet and the internet means that the request comes from any source IP address (you don't know what it is, so that's all.

  Basically, you want any source IP to hit one of your WAN IP on port 80, and then your firewall will redirect the request to the internal private IP address of the server on the same port 80. And when the answer comes back internal server, the firewall will already have this translate entry in and reverse NAT won't happen (you must configure it, the default firewall function).

  I hope that I have answered your question.

  Please mark as correct, if you like the answer.

  Thank you

• Single unit with multiple clusters CCM

  I know that this horse has been beaten to death, but I couldn't find a specific answer to my question.

  I understand with multiple clusters, each CCM to the unit calls go on Ports configured as such in each cluster. I also understand that MWI notification is sent by the highest numbered track and he's working his way down until it is successful. What I don't understand, is how to transfer out of the unit for the expansion of the Subscriber. How do I know what CCM Cluster to send the call to unity? He sends it on the main cluster and this group is responsible for the routing of the call on an inter-cluster trunk? Or should he behave as MWI where he tries to send calls from the highest numbered port until it is able to place the call?

  All calls from the unit (transfer and the identical outdials notification message) are only made on a port, the call is not retried on other ports like MWIs.

  The difference is that for communications, the unit will use the last available on the last group port. If you need to have put ICT in place correctly so the call can get routed to the correct phone on another cluster.

  For transfers, the unit will initiate the transfer using the same port that the call is entered in the. So if the transfer is supposed to go to a phone on a different cluster, yet once you have your ICT implemented between clusters so that the unit can transfer a call from one group to the other.

  In both cases, the unit simply connect, he does not know if the phone is in the same cluster or another cluster. So you must make sure that the dial string that uses the unit, as well as models of dial in CCM, download the call routed correctly through the TIC.

• Problem with: Clone, windows with a single NETWORK adapter

  Hello

  I have some bad problems while trying to use the following workflow: 'Clone, windows with a single NETWORK card. I always get the following error message: "task"CloneVM_Task"error: a specified parameter was not correct. "

  "Spec.Identity.Password.Value (name of the dynamic Script Module: vim3WaitTaskEnd #20).

  So I guess I have a problem with a password but I don't know what password, I give for the input parameter "channel passwork. It is encrypted if the indicator planText partner is false"I do not understand what password I would give here because I do not give any account of domain user.

  Is there anyone who has already used this workflow and can give me some advice on how to use it properly?

  Any help is appreciated.

  Thank you

  If I remember correctly, that's your administrator password local if it has been defined or the new password set if the model is no password defined. But then I did years ago doublecheck Yes.

• Transactions with IsolationLevel snapshot cannot be promoted. (VCAC5.2 + VCD5.1)

  Hi all

  I am using VCAC + VCD to deploy VAPP.

  I created VAPP and component VAPP. but when I submit my request that I got this error:

  • Error the applicant unit. Transactions with IsolationLevel snapshot cannot be promoted.

  someone you encounter this before?

  very appreciated for your reply, thank you

  I heard that maybe it's a bug in the installer to point 5.2.  There is a configuration where the deposit app.config file can use a connection string to the database while an individual model uses a different.  It is required by SQL Snapshot isolation not use DTC and thus multiple connections with different channels causes this error.

  It is a requirement that the templates that are installed matches the repository web application configuration in the web.config file.  This should be validated at run time, but it seems that our Installer does not validate this...  I suspect that this happens when the web model manager is installed with sql different information identification and then the Manager of model data.

  Check the Repository.Website\web.config on the Model vCAC Manager server/s to the path \Program files 9 x 86) \VMware\vCAC\Server\Model Manager Web\ for the parameter below...

  Make sure the server, database and the authentication setting that corresponds in the table below (case is important here too)...

  SELECT *.

  FROM [DynamicOps.RepositoryModel]. [Models]

  Data Source = localhost; Initial Catalog = vCAC; Integrated Security = True; MultipleActiveResultSets = True

  If they do not match, probably easier to manually change both to use iis authentication and restart windows, and check if the problem persists.  If this resolves the issue and you want a different configuration, laugh with the settings further and confirm the fact that it always works.

• The Clones related with 2 cards Ip address irregularities - network

  
  Hello world

  I have a headache to 5.2 view that I need help.

  I build linked clones, virtual machines need to have 2 network cards, 1 on the web and one for residents. I use a customization profile Windows based in vcenter. They go on the field and I set the network to custom settings and then put 2 NICs in DHCP. When I put in service 1 clone it worked, it was on the field, web access and internal ping etc etc. However, I have configured and then another, and I can not connect via RDP and PCoIP. Black screen times out after 10-20 seconds. If I understand correctly this is normally a network problem (normally only about PCOIP rather than RDP, I thought)?

  In any case, I put in service further and it seems (not to the letter) any other the world doesn't want to connect.

  When we look at in connection and vcenter, the only difference I see between the 2 types of vm that tab summary in vcenter, ones that work see the IP address of the card web access and those who do not work, shows the internal IP address. When you click Show all, ips are listed. It's confusing to me!

  When I reset the virtual machine (in vcenter) that allows me to log on to the console and it seems well, once I try to connect to pcoip it fails with the black screen and then I is even more ctrl alt del in the console of the vi client. It does not show that it has received a user either.

  Curiously, I rebooted one that did not work about 4 times and it seemed suddenly to the nic address and I can now connect with pcoip.

  Finally, addressing our network guys, he says that the PCoIP ports are open on the internal network, I can confirm this because it everything works fine in full mode with 1 NIC on the inside.

  Any help would be massively appreciated. Let me know if you need more information.

  Concerning

  David

  The agent will attempt to retrieve an IP address and report it to the connection to the server. Depending on how Windows presents the order of the list, he may decide to use the bad. For multiple network cards, you should follow the link below to configure the subnet mask and to ensure the right, it is always selected: Configure a Virtual Machine with multiple network cards to see Agent

  Mike

• Take a multiple snapshot of different VM´s

  Hello

  Anyone got a script to take different VM´s. example multiple snapshots when you windows patch id like to snapshot slected vm´s before applying the patch.

  Concerning

  Christer S

  Hi Chrsun02,

  "is it a medium esay to ad a function report to the commnad.

  Please tell more that you want to report on

  "im"wishing to' an easy way to get rid of stereotypes when I know that servers is ok. "

  Right, so before patching, you created snapshots for some virtual machines, and gave you the name of the snapshot for this purpose.

  for example

  Get - vm testgk | New-cliché - memory: $false - suspend: $false-name "testsnapshot001" - Description "my snapshot test patch before.

  on my vm testgk, I created the new snapshot with the name "testsnapshot001" for this pupose

  now I want to remove it

  Get - vm testgk | Get-Snapshot? {$_. Name - eq "testsnapshot001"} | Remove-Snapshot

  So I have vm testgk query, ask this virtual machine snapshots that have name testsnapshot001, and then delete the snapshot.

  If you have created snpahosts for more virtual machines give their name separated by a ",".

  Get - vm "vm1', 'vm2', 'vm3 | Get-Snapshot? {$_. Name - eq "testsnapshot001"} | Remove-Snapshot

  If you're sure you didn't any what other snapshots you can omit this part?: {$_. Name - eq "testsnapshot001"}

  so in the end, you would write:

  Get - vm "vm1', 'vm2', 'vm3 | Get-Snapshot | Remove-Snapshot

  If you don't want to answer the question confirmation add - confirm: $true

  Get - vm "vm1', 'vm2', 'vm3 | Get-Snapshot | Remove-Snapshot - confirm: $true

  If you want to specify vms not with names but with location:

  Get-cluster "my_cluster01" | get - vm | Get-Snapshot | Remove-Snapshot - confirm: $true

  If you want to get a report for snapshots:

  Get - vm | Get-Snapshot? {$_.name - eq "testsnapshot001"} | Select the name of name,@{N='VM'; {E = {$_.vm}}, @{N = "CreatedOn"; E={$_. Created}}

  So it will go through all of the virtual machines, instant advertising with the name: testsnapshot001 and display its name, date, name of the virtual machine

  Get - vm | Get-Snapshot? {$_.name - eq "testsnapshot001"} | Select the name of name,@{N='VM'; {E = {$_.vm}}, @{N = "CreatedOn"; E={$_. Created}}

  VM name CreatedOn name
  ----                                         -------                                 ---------
  testsnapshot001 testgk 21/08/2012 14:09:47

  And even once on the line will interview all machines virtual registerd in vc. If you want to check only for some more specific:

  Get - vm "vm1', 'vm2', 'vm3 | Get-Snapshot? {$_.name - eq "testsnapshot001"} | Select the name of name,@{N='VM'; {E = {$_.vm}}, @{N = "CreatedOn"; E={$_. Created}}

  or

  Get - vm "vm1', 'vm2', 'vm3 | Get-Snapshot | Select the name of name,@{N='VM'; {E = {$_.vm}}, @{N = "CreatedOn"; E={$_. Created}}

  to query all snapshots there and not only those that have been made for the purposes of the application of patches

  OR!

  a dirty, quick control for VMS with snapshots in general:

  Notice-EEG - ViewType VirtualMachine-filter @{"snapshot" = ""} | Select name

  I would like to know if it works for you.

  Kind regards

  Greg

• Photos of virtual machines with multiple disks on different LUNS - Question

  I have some questions on how to manage the snapshots of virtual machines with multiple disks on different LUNS.  First of all, the LUNS are VMFS.  We are just starting to add virtual machines with dedicated for data storage format VMFS LUNS.  I don't think an extra space must be made for snapshots, as well as at least 100 GB LUN is required to store the data, and then say, add about 25 to 50% of this amount?  Set the 100 GB vmdk file but have the GB from 25 to 50 additional disk space for snapshots, if necessary (rather than just to get a unit number logic needed 100 GB of data and devote all of the 100 GB to the vmdk file).  In addition, if a virtual machine has several files vmdk on different LUNS, which will be a problem to take a snapshot, and is it possible to do just a snapshot of a disk of a virtual computer (as the volume of the BONE)?

  Thanks for any help.

  Snapshot files are created in the home folder of the VM by default for all virtual disks, no matter on what data store they are. You must make sure you have enough free disk space on the data store for snapshots.

  If you want to exclude a virtual disks of taking snapshots, you can set it to 'Independent' - 'Persistent' machine virtual settings to the HARD drive.

  André

• Quiz with multiple responses

  Hello. I am a relatively new user to Captivate and am trying to create a quiz. I want to have questions which may have five or more possible choices (multiple choice), but two or more are correct.

  
  For example,.

  The first three letters of the alphabet are:

  1A

  2B.

  3 C

  4 D.

  5 E

  In order to get the right answer, the user must check the first three.

  I do not see this type of question format in pre-packaged ones that come with the software. Is there a way to do this?

  Thank you.
  Doug

  Hello and welcome,

  It is a Question multiple choice with multiple responses, is available. You can even turn on partial credit and use the sentence.

  

  Lilybiri

• date max with multiple joins of tables

  Looking for expert advice on the use of max (date) with multiple joins of tables. Several people have tried (and failed) - HELP Please!
  
  The goal is to retrieve the most current joined line of NBRJOBS_EFFECTIVE_DATE for each unique NBRJOBS_PIDM. There are several lines by PIDM with various EFFECTIVE_DATEs. The following SQL returns about 1/3 of the files and there are also some multiples.
  
  The keys are PIDM, POSN and suff
  
  Select NBRJOBS. NBRJOBS.*,
  NBRBJOB. NBRBJOB.*
  of POSNCTL. Inner join of NBRBJOB NBRBJOB POSNCTL. NBRJOBS NBRJOBS on (NBRBJOB. NBRBJOB_PIDM = NBRJOBS. NBRJOBS_PIDM) and (NBRBJOB. NBRBJOB_POSN = NBRJOBS. NBRJOBS_POSN) and (NBRBJOB. NBRBJOB_SUFF = NBRJOBS. NBRJOBS_SUFF)
  where NBRJOBS. NBRJOBS_SUFF <>'LS '.
  and NBRBJOB. NBRBJOB_CONTRACT_TYPE = 'P '.
  and NBRJOBS. NBRJOBS_EFFECTIVE_DATE =
  (select Max (NBRJOBS1. NBRJOBS_EFFECTIVE_DATE) as 'EffectDate '.
  of POSNCTL. NBRJOBS NBRJOBS1
  where NBRJOBS1. NBRJOBS_PIDM = NBRJOBS. NBRJOBS_PIDM
  and NBRJOBS1. NBRJOBS_POSN = NBRJOBS. NBRJOBS_POSN
  and NBRJOBS1. NBRJOBS_SUFF = NBRJOBS. NBRJOBS_SUFF
  and NBRJOBS1. NBRJOBS_SUFF <>'LS '.
  and NBRJOBS1. NBRJOBS_EFFECTIVE_DATE < = to_date('2011/11/15','yy/mm/dd'))
  order of NBRJOBS. NBRJOBS_PIDM

  Welcome to the forum!

  We don't know what you are trying to do.
  You want all of the columns in the rows where NBRJOBS_EFFECTIVE_DATE is the date limit before a given date (November 15, 2011 in this example) for all rows in the result set with this NBRJOBS_PIDM? If so, here is one way:

  with         GOT_R_NUM     as
  (
       select       NBRJOBS.NBRJOBS.*,
              NBRBJOB.NBRBJOB.*     -- You may have to give aliases, so that every column has a unique name
       ,       rank () over ( partition by  NBRJOBS.NBRJOBS_PIDM
                                 order by      NBRJOBS.NBRJOBS_EFFECTIVE_DATE     desc
                        )             as R_NUM
       from          POSNCTL.NBRBJOB NBRBJOB
       inner join      POSNCTL.NBRJOBS NBRJOBS       on    (NBRBJOB.NBRBJOB_PIDM = NBRJOBS.NBRJOBS_PIDM)
                                          and      (NBRBJOB.NBRBJOB_POSN = NBRJOBS.NBRJOBS_POSN)
                                    and      (NBRBJOB.NBRBJOB_SUFF = NBRJOBS.NBRJOBS_SUFF)
       where       NBRJOBS.NBRJOBS_SUFF             != 'LS'       -- Is this what you meant?
       and        NBRBJOB.NBRBJOB_CONTRACT_TYPE   ='P'
       and       NBRJOBS.NBRJOBS_EFFECTIVE_DATE  <= to_date ('2011/11/15', 'yyyy/mm/dd')
  )
  select       *     -- Or list all columns except R_NUM
  from       GOT_R_NUM
  where       R_NUM          = 1
  order by  NBRJOBS_PIDM
  ;
  

  Normally this site does not display the <>inequality operator; He thinks it's some kind of beacon.
  Whenever you post on this site, use the other inequality operator (equivalent), *! = *.

  I hope that answers your question.
  If not, post a small example of data (CREATE TABLE and INSERT, only relevant columns instructions) for all the tables involved and the results desired from these data.
  Explain, using specific examples, how you get these results from these data.
  Always tell what version of Oracle you are using.
  You will get better results faster if you always include this information whenever you have a problem.

• Frame content with multiple lines of text

  Hello

  In Indesign CS5 (Mac) is possible to get the same behavior as 'To adapt to the content Frame' pieces on a single line of text, to work with multiple lines?

  In other words, to adapt the framework to the height AND width of the text.

  We have black text and the text block has a fill and a stroke. What we are trying to achieve is to be able to quickly and accurately, resize it framework for however many lines it takes place in. By using the default behavior, so that we can use "mount the frame to the content" to get the height, but we need to manually drag the width.

  Thank you

  Try this (CS4/CS5):

  // Your Settings:
  var X_PRECISION = .1;     // pts
  
  // Some constants
  var     INNER = CoordinateSpaces.INNER_COORDINATES,
       MULTIPLY = ResizeMethods.MULTIPLYING_CURRENT_DIMENSIONS_BY,
       ADDTO = ResizeMethods.ADDING_CURRENT_DIMENSIONS_TO,
       AP_LEFT = AnchorPoint.TOP_LEFT_ANCHOR,
       AP_RIGHT = AnchorPoint.TOP_RIGHT_ANCHOR;
  
  function fitHorizontal(/*TextFrame*/ tf, /*str*/xRef)
  //----------------------------------------------------------
  // Fits a textframe width to its content
  // = adjusts the frame width to the optimal value without changing the height
  // xRef (opt.) is the reference pt: 'left'(default) | 'right' | 'center'
  // * You may invoke first tf.fit(FitOptions.FRAME_TO_CONTENT), i.e. fitVertical
  // * This routine supports rotated text frame
  // * Also, unlike the InDesign UI, this supports *multicolumn* TF
  //----------------------------------------------------------
  {
       // Default width multiplier. This value is only used if
       // tf overflows in its initial state. 1.5 is fine, usually.
       var X_FACTOR = 1.5;
  
       var ovf = tf.overflows,
            dx;
  
       xRef = AnchorPoint['TOP_'+(xRef||'left').toUpperCase()+'_ANCHOR'];
  
       // If tf originally overflows, we need to increase the width
       while( tf.overflows ) tf.resize(INNER,xRef,MULTIPLY,[X_FACTOR,1]);
  
       // Now, let's compute the maximal width variation (dx)
       dx = tf.resolve(AP_RIGHT, INNER)[0][0]-tf.resolve(AP_LEFT, INNER)[0][0];
       if( ovf ) dx *= (1-1/X_FACTOR);
  
       // Dichotomy on dx
       while( dx > X_PRECISION )
            {
            dx*=.5;
            tf.resize(INNER,xRef,ADDTO,[dx*(tf.overflows?1:-1),0]);
            }
  
       // Last step, if needed
       if( tf.overflows ) tf.resize(INNER,xRef,ADDTO,[dx,0]);
  }
  
  //----------------------------------------------------------
  // Sample code
  //----------------------------------------------------------
  
  // Assuming the user has selected a text frame
  var tf = app.selection[0];
  
  // Vertical fit (if you want it first --but not needed)
  tf.fit(FitOptions.FRAME_TO_CONTENT);
  
  // Horizontal fit (from the left edge)
  fitHorizontal(tf, 'left');
  

  @+

  Marc

• To create a ToolTip text for the image with multiple image map links

  Hello
  
  RH6 using, that I imported a picture into a topic. For the images that I have created several maps image to post a link to other topics. However, I can't create a map image additional to that same image that includes only the screen Tip text. I get a message of invalid value: "Please select a file, bookmark or topic to bind the hyperlink to.»
  
  Is there a way to create a popup only the text of an image with multiple image map links? My final output will be to WebHelp but possibly migrate FlashHelp in the near future.
  
  Thank you
  
  FMnRH
  
  
  
  Thank you
  FMnRH

  If the image is at the beginning of the subject, or all alone in a reference topic, you can put "#" (without the quotes) as the link for each area reactive.

  If the image is larger than the viewing window, it can jump to the top, but only if the user clicks on the link.

  I tried wz_tooltips and like it. I agree with Leon, it will take time for the first image but maybe go faster later.

  Harvey

• Web Forms using substitution variables with multiple values

  Hello
  
  I'm trying to select a substitution variable in a WebForm (Hyperion Planning 11.1.1.3) with multiple values in environmental assessments, but does not does someone knows if this expected behavior.
  
  I already try.
  
  & month = "Jan", "Feb", "Mar".
  & month = Jan, Feb, Mar
  & month = Jan: Mar
  
  Please let me know something, since I remember in previous versions of Hyperion Planning it was possible.
  
  Kind regards

  Reading of:- Re: use of the Variables of Essbase alternative forms of planning

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Sending Email with multiple attachments using packages

  Hi all
  
  Version: 10.2.0
  
  I am trying to send mail with multiple attachments using packages.
  
  I tried to use Mail_tools which is in http://www.myoracleportal.com/
  
  But I can send with only one attachment. Are there other options which i it allows to send with multiple attachments.
  
  I have bad do I send attachments Jasper instance < < converted to bytes > >.
  
  Please advice...
  
  TIA,

  My dear friend,

  If you are looking for in this forum - you can get it.

  Have you checked the forum?

  Anyway,.

  Here's the starter for you->

  http://forums.Oracle.com/forums/search.jspa?threadID=&q=sending+email+with+multiple+attachments+using+packages++&objid=F75&DateRange=last90days&NumResults=15

  Kind regards.

  LOULOU.

• How can I close Firefox (closed) if properly run two windows with multiple tabs in each and I want to save them all?

  How can I close Firefox (closed) if properly run two windows with multiple tabs in each and I want to save them all? I tried to close each window by clicking the X in the top right, and then restart Firefox only loads the last closed window. Is it possible to close Firefox so it restarts with both windows?

  Hi osenochen, some additions to the first response:

  • You can display the classic menu temporarily bar by pressing Alt or F10 to access the file menu
  • There is also an icon of 'power' at the bottom of the graphic application menu (the one which is displayed by the button "3-bar" menu) If you prefer
  • If you closed a window and you want to re - open, go to the history menu and see a list of recently closed windows (by default, up to 3 windows closed are stored and can be re-opened - not applicable to windows private)