TS200 hangs with the new memory

Similar Questions

• What can I do to make the Satellite A665-S6086 run with the new memory?

  I was able to update the BIOS for my Satellite A665-S6086 by updating 2.30 on CD burning. I have Windows 7 64 bit. I needed to update the BIOS, because I upgraded my RAM/memory of 2 GB (4 GB total) two cards two cards of 4 GB (8 GB total).

  My question now is when I start my computer with the new RAM/memory (two cards that are KTT-S3BS / 4G Kingston DDR3 1333 MHZ SODIMM SGL RANK), it freezes on the screen from Windows startup. Then when I hold the power button to shut it down and restart it, it wants to start using Windows repair but then crashes again. When I put in the memory of the old man and he start up, it starts the Windows repair and runs normally.

  What can I do to make my computer run with the new memory?

  I thank very you much in advance!

  What you can do?
  Buy an another RAM modules that are fully compatible with the laptop.
  It seems that you want to use the RAM modules which are not totally compatible and therefore the system hangs.

  By the way: the CPU that is used in this notebook runs the DDR3-800 and DDR3-1066
  RAM modules.
  http://Ark.Intel.com/products/49020

  I would not recommend to use the modules of DDR3-1333 but PA3677U-1M4G 4 GB DDR3-1066

• Tecra 8200 does not start with the new memory module

  Hi, ive just rode this memory to my willingness to .it tecra 8200 not initialize the message comes up / remove the incompatible memory in B / someone knows why?

  Memory for laptop IBM 256 MB PC100 144 pin SDRAM SODIMM

  IBM FRU L 33, 3070, 256 MB PC100, SDRAM SODIMM, no parity, 3.3 volts, 144 pins, 32 MB x 64

  Thanks for the replies biff

  Hello

  Well, I really put t know why this message occurs. It seems that this module must be compatible with your device. Are you sure that the module has no fault?
  Have you tried to use this memory module in Bank?

  Otherwise I found other compatible memory modules.

  PC100 256 MB (PA3069U - 1 M 25)
  PC100 128 MB (PA3005U)
  PC100 64 MB (PA3004U)

  http://www.frontline.co.UK/product_detail.aspx?pid=MEMKNG5662

  Good bye

• video hangs with the new card in an old Slimline s3500t

  Hello! I have a slimline pc t3500 and changed a noisy gs9500 for an asus fanless hd 5450. now I can't watch the flash and all of my video players fall opening any avi or other video format. But it's awful quiet. Any suggestions? How can I update, because the correct video card driver is already installed. Thank you very much. Oh, and I am runnig Vista home 64 bit everything to date. What is my power 180 watt? Otherwise, the pc works fine and graphics show without aberrations.

  Ububoy, I hear what you say.  However, if the 9500 GS came with the computer it was probably manufactured according to the specifications of HP to use less energy.  This is how HP makes video cards work, that the manufacturer States use more power, in their computers.  The HD 5450 is even more power than some of the PSU design can handle.  You can try to unplug all unnecessary components (CD player, USB components, etc) to see if that helps.

• BSOD when trying to install Win7 64 bit with the new motherboard

  Hi all

  I have the following BSOD problem:
  I installed a new motherboard in my system (a MSI P43 C51). Before that, I got a Gigabyte G41MT-S2P. The rest of the configuration is: Q9650, Thermaltake truespirit 90 cooler, 2 x 4 GB DDR3 1333, GTX 470, 750W PSU, case name, SATA HDD 500 GB, Windows 7 64 bit.

  Well, the problem started when I tried to boot into windows with the new motherboard: I got BSOD 1 second after windows starts loading. I thought... new motherboard, install new windows, so I tried to install windows 7 64 bit DVD and USB stick, I get the STOP: 0x0000000A error during installation. I changed the HARD drive, thinking that it could be a bad sector problem, but no, the other hard drive behaved exactly the same thing. I got BSOD at 40% extraction, extraction of 90% and for the moment "Complete the installation..." ». I also tried to install with the stick of memory only one, spent between ports, everything. The material I have works, as I played on my PC every day in the last month and received no. BSOD, also had a small overclock the CPU and the GPU (100 MHz on the processor, that the old motherboard supported more than 343 fsb and about 100 MHz on the GPU). It was stable, no errors, no nothing.

  My thoughts are only, after asking some knowledge that work in computer support, it could be a problem of version of the BIOS (BIOS is 2005..) and the fact that my Win 7 installation kit is without Service Pack 1 (a colleague told me that he had this problem for the PC more than once and after trying to install SP1 It went smoothly and without errors)

  I just got a new "blank" DVD of Win 7 64 bit with SP1. What I'll try today is to Flash the bios with the latest version and install the OS on a HARD drive new, sealed. He could not be my system components, because they are compatible and they worked 1 day before with no problems! I have literally NO IDEA what could be the problem. Today, I'll try the installation of the new DVD and with the new version of the BIOS. If this does not work, I have no idea what I can do... It is a sucky situation.

  If you have any suggestions, please, don't keep it to yourself :-D

  Thank you!
  Alex

  Hello

  See this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top two responses.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/8df6485a-50cc-4cdc-BE3E-0f05c7745117

  ==============================================

  References to Vista also apply to Windows 7.

  Drivers could be at fault, however the problems of disk or security/antivirus/antispyware products are
  just as likely to be the root cause that they can force a driver to corrupt or go out of bounds.
  The video driver or something affecting it would be questionable.

  At the end of this message, I'll post a bluescreen generic and in the next convenience store
  How do to update the drivers and BIOS but also to check memory message.

  -----------------------------------

  BCCode: 0a 0x0000000A

  Cause

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

  The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

  Solve the problem

  If a kernel debugger is available, get a stack trace.

  To resolve an error caused by the faulty device driver or service system, BIOS

  1. Restart your computer.
  2. Press F8 to character-based menu that displays the choice of operating system.
  3. In the WindowsAdvanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

  To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

  1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
  2. Try disabling the cache in memory of the BIOS.
  3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
  4. Make sure that the latest Service Pack is installed.
  5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
  6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

  If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

  Comments

  Before upgrading to a new version of Windows, remove all third-party device drivers and system services and disable any antivirus. Contact software manufacturers for updates of these third-party tools.

  BCCode: 0a 0x0000000A<-- read="">
  * 1025.html http://www.faultwire.com/solutions-fatal_error/IRQL-not-less-or-Equal-0x0000000A-

  ==================================================================

  General troubleshooting BlueScreen to use with the methods above.

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
  to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  I hope this helps.

• Can I change the new memory and at the same time to replace the Rams?

  Can I change the new memory and at the same time to replace the Rams?

  If a MacBook Pro RAM and drvie hard can be modified/improved depends on the submodel and we do not know yours. There are dozens of variations of the MacBook Pro issued since 2006, and you do not want guessing us!

  Please do "about this Mac" in your Apple menu to get this:

  

  Notice the line that I have highlighted with the red arrow. Please tell us what your computer has in the thr same place. However, do not post any serial number.

  With the exact submodel we can better advise you of any available upgrade paths.

• I want to know how to remove the back cover of my HP Pavilion Sleekbook 15 to install the new memory?

  I want to know how to remove the back cover of my HP product name: HP Pavilion Sleekbook 15 to install the new memory?  All site shows HP Web is how remove caches memory.  Unfortunately, with the newer models like mine, the whole back cover needs to be removed.  I have tried in vain to remove it, but so far all that I managed to do is scratch my cover.  If anyone can help?

  Dear David

  It's a very good idea, it would also be a good excuse to use my new phone for this.  So I'll say thanks again for the good advice.  Have a great weekend you Mr.  As I said earlier, you're a star...

  Yours Sincerely

  Alan

• I bought the extra memory. What I have to do something when I install the new memory? __I went to Disk Defragmenter and it always says that I have 35% of free space. The new memory will change this amount? Or is it important?

  I bought the extra memory.  I have to do something when I install the new memory?
  I went to the Disk Defragmenter, and he always says that I have 35% of free space.  The new memory will change this amount?  Or is it important?

  Monday, December 20, 2010 18:53:59 + 0000, Magallón wrote:
   
  > I bought extra memory.  I have to do something when I install the new memory?
   
   
  Generally no.
   
  How many memory currently have installed? How did you buy?
  Did you buy exactly the same type, brand, model, etc. ?
   
  Why do you want more memory? Depending on how much you have now, and
  What applications you are running, it may or may not do anything for you. More memory
  is this not better for everyone. This is my standard message on this
  Object:
   
  The amount of RAM you need to good performance is * not * a
  unique situation for all. You get good performance if the amount of
  RAM you have prevents you from using the file page in a meaningful way, and
  It depends on what applications you are running. Most of the people a typical range running
  Enterprise XP applications find that somewhere around 512 MB
  works well, others need more. Almost everyone will see poor performance
  with less than 256 MB. Some people, especially those who do things
  as modification of large photographic images, can see an improvement in performance by
  adding even more 512 MB - sometimes much more.
   
  If you currently use the page file significantly, more memory
  will reduce or eliminate the use and improve your performance.
  If you do not use the pagefile significantly, it will make more memory
  nothing for you. Reach
  http://billsway.com/notes%5Fpublic/WinXP%5Ftweaks/ and download
  WinXP - 2K_Pagefile.zip and monitor your use of the page file. Who should
  give you a good idea of more memory can help and if so, how
  lots more.
   
   
   
  > I went to Disk Defragmenter, and he always says that I have 35% of free space.  The new memory will change this amount?  Or is it important?
   
   
  You have 35% of your hard drive free. It's disk space, also called
  storage. It is not memory, what is RAM. Adding memory will not make
  any changes to the available disk space.
   
   

  Ken Blake (MS-MVP)

• Constant BSOD with the new laptop computer

  I bought a laptop Dell L521X are three or four weeks ago, and since then have had difficulties with the projection of thing regularly blue on me at arbitrary points. Those initial seemed to result from McAfee LiveSafe who settled on the laptop so I uninstalled this and these people arrested. However, since then he has been giving me an error called DRIVER_POWER_STATE_FAILURE he says is caused by ntoskrnl.exe. Blue screens seem to happen arbitrarily and not because of anything specific I'm doing on the laptop. It will almost always crash when it is in "standby", however, and a few times he broke down while I'm closing. I updated both drivers and BIOS, hoping that would solve the problem but neither helped. I thought that it could be a hardware problem but all the Dell diagnostics, I came back with nothing. I've been futzing with the thing for a while now trying to figure out what it is but I'm stumped. If someone wants to look at the crash dump files I the downloaded in a zip here: [x]

  I really want to fix this because I don't want to take over the laptop. I bought the thing because I had problems with my old, and here I will once more in trouble with the new! I hope you guys can help me. Thank you!

  DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)

  This indicates that a kernel-mode driver attempted to access pageable memory with a high IRQL.

  A driver tried to access a pageable (or that is completely invalid) address while the IRQL was too high. This bug check is usually caused by drivers who used a wrong address.

  STACK_TEXT:
  fffff880 '099013f8 fffff880' 018d636f: fffffa80 '13-57040 fffffa80' 118ac174 fffff880'09901460 00000000 00000000': 0 x 0
  "fffff880 ' 09901400 fffff880'd 018 7128: fffff880 ' 00000000 fffffa80 ' 100f5520 00000000' fffffa80 00000000' 00000000: ndis! ndisMSendCompleteNetBufferListsInternal + 0x10f
  fffff880 '099014-0 fffff880' 1009da83: fffffa80'132 ca 010 fffffa80 '132c88d0 00000000 00000000' fffffa80' 132bcb00: ndis! ndisMSendCompleteX + 0 x 188
  fffff880 '099014f0 fffffa80' 132ca 010: fffffa80'132c88d0 00000000 00000000' fffffa80 '132bcb00 fffffa80' 10eba1a0: SBFWIM + 0x2a83
  fffff880 '099014f8 fffffa80' 132c88d0: 00000000 00000000' fffffa80 '132bcb00 fffffa80' 10eba1a0 00000000' 00000000: 0xfffffa80'132 ca 010
  fffff880'09901500 00000000 00000000': fffffa80'132bcb00 fffffa80 '10eba1a0 00000000 00000000' fffffa80' 13f706b0: 0xfffffa80'132c88d0

  Gah... I suspected that this software to be a problem, but I wanted to be sure before recommending removal. Sunbelt Firewall is originally NETBIOS conflicts, I see quite often. It is quite problematic software (IMO), so I would remove as soon as POSSIBLE.

  Kind regards

  Patrick

• Question "BOLD" of blackBerry Smartphones and synchronization with the new Media Sync for Mac

  Someone at - he had problems with the new media manager not achievements the media in the "BOLD" card, it worked for my curve but not the "BOLD" it says for me to insert the press card. I tried formatting, but still used hired there is one in there to transfer my iTunes. Any suggestions?

  I just tried sync'ing a playlist from iTunes to my "BOLD" w / Media Sync and it worked fine. I don't have a memory card either. It took two trials - the first doesn't seem to work, but the second went without a hitch. You have your "BOLD" value will automatically switch on the mass storage device when connected to your Mac - I do not know if it would make a difference.

• Need help to update to work with the new vSphere environment 6

  I have a great powershell script some time ago, I created to clone our production servers in a development environment and configure them for use in isolated vShield development networks.

  We have recently updated our environment vSphere vSphere 6 and changed architecture autour 5.

  Previously with vSphere 5 we had a unique vCenter server that managed our two datacenters by itself.

  With the new design of vSphere 6, we have a PSC and VCSA server to each data center in one area of SSO.

  The first thing I did with my script of cloning is up-to-date reference vcenter for a table of two servers, so I connect to two VCs at the same time.

  This allows me to see and manage the two vCenters virtual computer guests, so get - vm strives to see the comments of the source.

  However, the problem is that when I try to clone a virtual machine from one data center to another, the command fails because it can't find the virtual machine to clone.

  # Virtual Centre server or VM host to connect to
  $aryVIServer = @("vc01.domain.com", "vc02.domain.com")
  
  # Load VMware environment
  Set-PowerCLIConfiguration -DefaultVIServerMode Multiple -InvalidCertificateAction Ignore -Confirm:$false | Out-Null
  $VIServer = Connect-VIServer $aryVIServer
  
  # Server cluster group to deploy to
  $strVMCluster = "Bubbles"
  
  # Define name of new server including environment prefix
  $vmName = "$($envPrefix)-$($CloneServer)"
  
  # Select Host with least memory consumption
  $selectedHostObj = Get-VMHost -Location $strVMCluster | Sort-Object -Property MemoryUsageGB | Select-Object -First 1
  
  # Select folder to place VM guest into
  $folderObj = Get-Datacenter -Cluster $strVMCluster | Get-Folder $selectedBubble
  
  # Select datastore with most available space
  $selectedDatastoreObj = Get-DataStore -VMHost $selectedHostObj | Sort-Object -Property FreeSpaceGB -descending | Select-Object -First 1
  
  # Clone new VM from running Server
  $newVM = New-VM -Name $vmName -VM $CloneServer -VMHost $selectedHostObj -Datastore $selectedDatastoreObj -DiskStorageFormat "Thin" -Location $folderObj -Confirm:$false
  

  He used to work very well when there was a single VC but of course does not now with two.

  So far, the only difference is the change in VCs. We always use the same exact 5.0 running ESXi hosts to the same place in separate data centers.

  Oh and I'm now using powercli 6.3 R1 instead of 5.5 R1.

  I look forward to this type of procedure should work fine, and I just need a different command for virtual machine cloning now?

  Well, I have solved the first problem according to them here:

  Re: Impossible to deploy VM model on different vCenter Server (in the same domain of SINGLE sign-on)

  However, now I can't run Invoke VMScript without getting an error that the proxy authentication is required.

  If I remove all my proxy settings in Internet Explorer, then it connects fine but this script must be run by a number of engineers without being dependent on their proxy settings are disabled.

  I can programmatically change the settings of proxy at the beginning of the script, but nothing not preventing to change those back if they use their browser and break execution of the halfway of script.

  Never had any problems with the Proxy settings before and I didn't know any other messages that have directly relevant air.

  Anyone know of a way to avoid this?

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• I had a problem with my iPad 2 Air when I changed my Apple ID password, the problem is, it shows me a Massage says ENTER the PASSWORD, and then said your PASSWORD will be used when the signature with the new device, but when I but the code it shows fail m

  This problem happened to me and it belongs to iCloud and I have used so important, please can someone help me?

  Hello. The access code on your iPad is the code four or six numbers you will need to enter to unlock the device. It has nothing to do with the verification of your Apple ID or two-step. Are you able to unlock your phone? If you are, then please describe the steps that lead to your problem. Since you have changed your Apple ID password, you will need to go to two settings > iCloud and settings > iTunes and app store and sign out of your Apple ID, then connect back with the new PW.

• iTUNES Podcast App on the iPhone with the NEW IOS 10

  With the new update, I find that my podcast with iTunes app speeding up shows. Anyone else having this problem?

  Podcasts allowing control of playback speed. You probably activated accidentally.

  

• help with the new option of memories

  Sorry for my English

  Please help me with the new option of memories

  no memories option appears me

  I have an iphone with IOS 10.02 5

  Hello

  Try this support article > enjoy your memories in pictures - Apple Support