Tunnel 6rd Linksys e4200 v2 problem

Similar Questions

• Linksys E4200 - can update firmware and roll backs damage my router?

  Hello

  I had to restore the firmware on my Linksys E4200 (v2) because I had problems after upgrading the firmware. I tried to upgrade again and again met with problems. In short, I improved a few times and restored several times. Currently I'm on the old firmware and I without any problem.

  In the old days, it was not wise to update the firmware of some peripheral hardware too often, because some devices has agreed that a limited number of updates to firmware... don't ask me why :-)

  Is this also the case with the Linksys E4200 or can I upgrade and roll back as often as the requires, or as often as I want to try to upgrade because of new features...?

  Thank you

  SJW

  As long as you do the right steps during the upgrade/downgrade the router (loading the firmware using a wired computer, not to interrupt the upgrade/downgrade process, load the right file, etc.), the unit should be fine.

• Linksys E4200 - Skype internet killing

  Hello

  Recently, I went from a router D-Link GamerLounge for a new Linksys E4200 using the default firmware, upgraded to the latest version.

  The router seems to work fine - except when someone uses Skype, and performance of the network decreases drastically. I have tested it with Skype running on a wireless laptop and test my Wired PC network. Here are the results of ping www.google.com with and without Skype:

  Without Skype (wired PC ping):

  Reply from 74.125.113.103: bytes = 32 time = 132ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 83ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 183ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 105ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 48ms TTL = 46

  With Skype (running on the laptop wireless, PC ping wired):

  Reply from 74.125.113.103: bytes = 32 time = 132ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 83ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 183ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 105ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 48ms TTL = 46

  I searched a bit on the internet and have not found anyone with a similar problem. Someone at - it suggestions? I guess I could try to upgrade the firmware again or something.

  Probably due to the quality of service. You said it was a GamerLounge, which I suppose has automatic QoS for the games.

  You can configure QoS on the linksys as well, it's just not the installer for the game by default.

• Linksys E4200 - range WUSB600N V2 / signal issues

  Router Linksys E4200 dualband and Win7 64 bit Linksys WUSB600N v2.
  Both in the same room, the distance is about 10 meters.
  I compare the results on 5 GHz btw the stick of Linksys and btw another laptop with Intel Advanced-N 6200 AGN wifi chip.
  Running a wifi 5 GHz N on the stick of Linksys, leading to the signal strength low and reduced its speed.
  Practically, I can't improve the signal than the Intel + 15 to 20 dB...

  Negligible:

  distance / Intel / Linksys:
  <1 m ="" -26db="">

  5 m /-50 dB /-65dB

  While Intel radio affects 300 MB/s, the Linksys is somewhere around 200 MB/s only. in the same room
  Anyone else knows a bad signal with the WUSB600N v2, as well? I bought the stick to stream HD media, but with - 65dB is not much of an improvement to what I had on 2. 4 Ghz, 802.11 g (())

  Sorry, but how is this releated response must keep the problem I described?
  disable the firewall on the router spi?
  I checked the possibility of automatic channel selection and channel 20-40 establishments width (automatic channel selection does NOT work correctly from either). I still have the experience that the stick has lower than intel one signal. regardless of the setting of the router firewall 

• Linksys e4200 with wifi direct does not connect to the kdl-48r470b

  I just bought a Sony kdl-48r470b tv of the grand prix of Wal-Mart and image, but with the info on this tv being ill not do now to the community for help here.

  Im trying to connect the TV via wifi direct to my router from linksys e4200. the router has wifi direct.  my pc is connected to the router via a network cable. the idea here is that I want to push films to the router, then to the tv via wifi direct.

  the problem is that the tv refuses to connect to the router told me just recording failed. Ive tried the pin of my router still nothing ive disabled the security still has nothing, Ive used the method push button and still nothing.

  is it possible to connect to the router? IM thinking this way because it has direct wifi.

  I contacted sony 3 days ago and have received zero responses from them

  Thanks in advance for your suggestions

  So what you saying is this TV is not able to sell the linksys router? I'm still so confused with this TV... If it says built in wifi, you should be able to connect to your router... looks like there should be a way...?

  very irritated by this situation!

  Thanks for the quick reply... too bad sony can't come back with me with a solid answer... or I could at least understand the rep...

  Denise

• Linksys E4200 and VoipBuster sip call

  Hello

  Just recently bought a router Linksys E4200 and it was rocking so far! I've updated since a WRT320N. However it seems that the call SIP (using my account Voip Buster) no longer works...

  I don't seem to be able to register with the Voip service. Port is 5060 standard (if I remember correctly, I'm not at home now) and I've already enabled on the router the special tick for Voip calling ALG. Router is upgraded to the latest firmware and it's the V1 router.

  With all the foregoing, I cannot yet connect to VoipBuster using SIP. It worked like a charm with the WRT320N, so it's something with the router.

  Can anyone help? Thanks a bunch!

  Try the following steps:

  [A] with the help of the Cisco Connect software (if at all, you have installed the router using this software)

  1] open the software and go to the option that says "settings of the router.

  [2] then click on the option that says 'Advanced settings', which will take you to the router configuration page.

  [3] lower the MTU (Maximum Transmission Unit) of 1500 to 1400 or less (usually found on the main page / basic configuration of your router)

  4] click administration and disable UPnP.

  [B] If you have not installed Cisco connect then you can connect to the router's user interface using its default IP address in the browser which is 192.168.1.1 and enter "admin" as password empty username field. This will take to the web interface of the router and then follow the steps as indicated above to make the changes.

  Second, it also depends on the type of VOIP provider, you must open the ports on your router. H.323 uses 1719 and 1720 for signaling, dynamic ports for media. SIP tends to use 5060 for signage, dynamic again for the media.

  Follow this link and open the ports on your router to your VOIP: http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&login=1&app=search&vw=1&articleid=17241

• Microsoft teredo tunneling adapter has a driver problem

  Original title - trobleshooting driver

  Microsoft teredo tunneling adapter has a driver problem. I got this message when I have my PC troubleshooting

  my PC is HP Compaq 615 Windows 7. How can I solve this problem?

  Uninstall the adapter Teredo, ISATAP, IPV6 nor Microsoft 6 to 4 cards and by going to control panel > system > Device Manager > view > show hidden devices, and then expand the network adapters entry and do a right click either disable or uninstall one of the adapters I mentioned, and then restart your computer.

  You need not Teredo adapter to connect to a domain or a shared drive, and the special features of Microsoft claims to offer with the Teredo adapter do not work in Windows 7 in any case.

• Printing error, "MS Teredo Tunneling adapter has a driver problem".

  Suddenly can't print.  Troubleshoot the error for computer says "MS Teredo Tunneling adapter has a driver problem". What this means and how do I print my documents.  Printer works but the computer seems to be the issue.  Any help is appreciated quickly - need to print documents cruise and concert tickets! @

  SR

  Teredo tunneling is a network used by some printers Protocol. First thing I would do is to run a filesystem check and reinstall the printer driver.

  Please run a check of system files (SFC) 

  
  

  All instructions are in our Wiki article below...
  If you have any questions please ask us for .

  Check the file system (CFS) Scan and repair system files

• Linksys E4200 and connectivity Motorola SBG6580

  Here is a picture of my home network. The problem I'm having is, I can't get the WD MyBook Live Duo to be seen on the entire network. If it is connected to the Linksys, all computers connected to the Linksys can see it, but not those related to the Motorola. If I put it on the Motorola, the same thing happens, but in the visa versa. I bought the Motorola for its DOCSIS 3 capabilities, not for the wireless. I prefer to use the Linksys Wireless. Any help would be greatly appreciated.

  

  Devices must be on the same subnet (e.g. 192.168.1.x) to be able to see each other. You could make the Sb IP 192.168.1.1 and 192.168.1.2 for the E4200 and connect a cable from LAN of the SB E4200 (not WAN) port lan port.

  Here is a guide if you need: http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=3733

• Microsoft teredo Tunneling adapter's driver driver problems

  Hello you signed up for the first time and by publishing too. Ive never had problems with my laptop Acer Aspire 7540, it's a windows 7 64-bit. Recently, Ive noticed it is very often the Crackle from audio sources, mainly when researched online, not so much by using WMP. As a result, I had a quick look around my PC and found I have a "!" mark to the icon for laptop. He asserts that this Teredo Tunneling adapter driver issues. I tried following the instructions on the screen to fix this, but he came to failure and the State of "Details" that there is a "problem with PNP devices.

  I had a look on google and tried the advice to go to my network connections and sΘlectionnΘe wireless network connection, click with the right button on properties and confirmed that IPV6 (TCP/IPv6) has been activated, so I guess I can exclude that as a problem.

  There is also a connection to the local area network and Wireless Network Connection 2 listed under network connections both have red "x" next to them. I use wireless, like my mother on his Acer laptop. LAKE says "network cable Unplugged, WNC2 States 'not connected'.

  I came Acer to reinstall the driver, but when entering my S/n number or SNID happens model unrecognized. When entering ACer ASpire 7540 a list of drivers is here but nothing called Teredo.

  Would appreciate any help that anyone can give. Don't even know if this driver will fix sound problems, or if my speakers are simply disappeared (lol), but I would like to do, of course, I have all work as good as possible.

  Thanks again

  Stem

  The Microsoft Teredo Tunneling adapter isn't a default device you see in Device Manager.

  Something else has created a problem on the system.

  You can visit this thread on the forums of Microsoft:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/Microsoft-Teredo-tunneling-adaptor...

• How can I fix adapter Teredo Tunneling Pseudo-Interface of network problem that shows an indication of a problem in the Device Manager?

  I've never seen this problem before.  The yellow triangle with the exclamation point is visible on this network adapter called Teredo Tunneling pseudo-interface.  The driver update does not work, and apparently the last and the best driver is already installed for this device.  I tried to disable and searching for the hardware changes.  Whenever the device is displayed again with an indication of problems triangle and even yellow exclamation point.  It is said that the device cannot start.  I rebooted the machine to see if something has changed.  There can be no.
  I just uninstalled the device and scanned for hardware changes, but it has not been detected and remains missing under the network adapter category.  I ran diagnostic system provided by HP software, but nothing seems to be defective.

  Hello

   
   
  1. What is the code that you see under the status of the device and the exact error message?
  2 have you made changes on the computer before this problem?
  As you have already tried updating the drivers and still you face the same problem, you can try to uninstall the existing driver and manually download the stand-alone version of the driver and install it.
  Step 1: first of all, I would say you temporarily disable any security software and then try to install.
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
  Step 2: Now try to install the drivers
  a. open the Device Manager by clicking the Start button, click Control Panel, clicking system and Maintenance, and then clicking Device Manager.
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  b. identify the sound card, right-click on it and select Properties .
  c. go to the driver tab and click Uninstall to uninstall the driver associated with the device.
  Restart the computer and install the latest driver.
  Reference: Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
  Get help with Device Manager errors
  http://Windows.Microsoft.com/en-us/Windows-Vista/get-help-with-Device-Manager-errors
  Overview of Teredo

  http://TechNet.Microsoft.com/en-us/network/cc917486.aspx

   

   

• Cisco Linksys E4200 v2 fails to process UPNP requests

  Bought a new router E4200 v2 version last month and replaced my dlink dir-655 and I started to see the alerts on my server at home that it is impossible to configure the router.

  Already checked on the router that UPNP is enabled. already tried disabling the firewall, ipv4 and ipv6 and turning too wide "filter applications anonymous Internet", but does not

  then in WHS 2011 troubleshooting guildline, I ran a router online test tool: http://www.microsoft.com/windows/using/tools/igd/results.mspx

  and all tests passed except "Testing UPNP" and the poster details a mistake:

  'Test 5 - UPnP Support Test not supported

  Result:

  The operating system is Windows Vista
  The firewall is turned on

  Exceptions are provided by the firewall

  UPnP is enabled by the firewall

  UPnP services are running

  Discovery of UPnP is enabled

  Detect Internet gateway on the network devices

  2 RMI (s) found

  The IGD device information:

  Name manufacturer: Cisco

  Model name: RMI

  Model number: v1.0

  get_StaticPortMappingCollection() returns NULL IStaticPortMappingCollection

  get_StaticPortMappingCollection() returns NULL IStaticPortMappingCollection

  get_StaticPortMappingCollection() returns NULL IStaticPortMappingCollection

  Could not get the IGD port mapping ".

  Now, it seems that my router is bad or cisco/linksys does not support this API and is not compatible.

  is there a way to fix this?

  * Firewall can block almost all of the ports used by P2P clients. Check if the BitTorrent ports are made available to customers requesting. Disable the firewall of the router and enable uPnP features allow the BitTorrent ports to pass through.

  * As E4200 is a new Cisco router usually have a good level of security, and unless you have a good configuration configured on the router it can block the software work that uses UPNP.

  * If the ISP updates for IPV6 nodes still functionality for IPV4 will exist as the Lauch of IPV6 also depends on the hardware compatibility

  So, once reset the router for Hard Reset 30/30/30

  The following procedure will clear the NVRAM and set the router back to the default values:

  With the power on, press and hold the reset button the back of the unit for 30 seconds
  Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
  Plug in the appliance ALWAYS keeping the reset button a final 30 seconds...

  Then reconfigure the router once more and then check the concern...

• Weird Linksys x 2000 problem

  Suddenly, I was not able to connect to websites at random and do not been able to add elements of online stores to cart.  I couldn't believe the router it would, but I've confirmed.  With Linksys x 2000 installed, I tested Linkedin.com on four of my computers.  2 Windows 7 Machines, Machine 1-Windows8 and server 1-2011. After you type the user name and password, page refresh to the login screen and does not allow me to connect to.  I tested it on all 4 machines.  Also tried to order something online and not allow me to put items in the basket.  Once tested on all four machines.

  I set the router to the factory settings and tested and got the same results.  Disabled firewall and got the same results.  Ensure time was OK and got the same results. I had the latest firmware, 2.0.4 (or something like that) and no newer updates.

  I replaced the Linksys X 2000 with provided ISP router Westell 8500 and none of the problems persisited.  Definitely something wrong with the x 2000 Linksys.  I'm in the Eastern time zone and think that the problem began with Day LIght Saving time, although I can't be sure.  Routeris is good time however.  Yet once, provider ISP don't give me any problems.

  Anyone else with the same problems?

  Yes, there are a lot of discussions on this problem. The problem is that cookies are blocked. Go to the security settings on the router and check the cookie. Who's going to fix it until we get a firmware update.

• Linksys WAP200 DHCP problem

  Hi, I have problems with the Linksys WAP200. When you use WPA/WPA2 Enterprise client hangs for about 60 seconds to try and obtain an IP address after a successful authentication. AccessPoints from other suppliers do not show this behavior.

  I did a tcpdump and comapred an accesspoint of another provider in the WAP200 work, and it seems that the WAP200 is reject bids that are sent via unicast DHCP. When the dhcp server sends an offer through broadcast after 65 seconds, it reaches the client and all is well.

  This is clearly buggy since the access point seems to be filtering the DHCP responses, is there an option to solve this problem?

  WPA is a known issue with the WAP54G as well. He breaks the wireless link entirely if you use Repeater/bridge modes. It is possible that Linksys a general isue with WPA in several similar products.

  So that it is resolved I feel Linksys just to be notified in writing. This also provides a written question should be wound.

  Concerning

  Fred

• Linksys WUSB54GC driver problem Windows 7 64 bit - will not allow

  I have a Linksys WUSB54GC 3 Wireless Network Adapter version.  I downloaded the latest driver on the Linksys support page that says that it is fully compatible with Windows 7 64 bit.  The adapter will not allow.  After 3 grueling cat takes support sessions with Linksys, they could not understand it and threw the problem back to my Tower say it must be a problem with my Windows 7 64 bit.  I searched for Windows and Linksys support forums and some people have had luck, and others have not.  The driver has been installed manually several times as well as the removal of material, resettlement and loading the driver again and again.  I am trying to connect to my router Linksys WRT54G which has the latest firmware and has another computer wireless connected to it without any problems.  If anyone can help?

  Hello

  Have you tried the device on another computer just to be sure, does it really work?
  Have you tried another device on this computer?

  Are you logged on as ADMINISTRATOR when you do the work? Right click on the driver
  and RUN as ADMINISTRATOR?

  ----------------------------------------------------------

  References to Vista also apply to Windows 7.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -----------------------------------------------

  Then lets refresh the USB stack

  The device here is the WiFi device:

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the driver and battery USB

  This KB shows XP how to and methods of Vista and Windows 7 are the same
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer.
  as well as all USB devices that you previously used. Run Options and tick three 1
  are there choices to see if any.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.