Linksys WAP200 DHCP problem

Similar Questions

• WLC and Linksys DHCP problem

  Hello

  I have a WLC 2112 and a DHCP Server enabled on a Linksys router. I set up a wireless LAn to have the IP address of the Linksys DHCP server, but it does not work and when I configure the DHCP anthor server it works.

  Can you help me please

  Your controller cannot ping the LinkSys Router? In addition, you set up the DHCP server on the interface of the controller, correct?

• Satellite C870-1J6 wired LAN DHCP problems

  Hi all

  Here, I have a new laptop C870-1J6, which makes my life miserable. It won't start not reliable PXE, and the network card also does not start in Windows.

  On a cold start the PXE boot Gets an address dhcp fine most of the time, but a warm reboot fails most of the time.
  In windows this NIC also does not start. After five to ten minutes, he finally gets an address from the DHCP server. Rest of the network works fine.

  No points for guessing the manufacturer of the network card, of course, there a realtek :-(
  "RTL8102E/RTL8101E PCI Express Fast Ethernet controller.
  PCI ven: 10EC, dev: 8136

  None of the solutions, or can send Toshiba somehow? because I don't think I can do a lot on the PXE problem myself.

  At first, I have to say that I m really wondering why you have problems of LAN under Windows.
  Have you noticed these LAN issues from the first day of use?
  Are you using the original pre-installed OS that you got with your laptop or a facility clean or even company?

  Maybe stupid question, but I assume that LAN is set as first boot device, right?

• Trek PR2000 DHCP problems, maintains a drop connections, perhaps workaround

  Hello!

  A few days ago, I bought the new Netgear Trek PR2000 mobile wireless router. Goal was to have a point of contact for all my devices while traveling and be able to connect to a hotspot or wifi in the hotel.

  Configuration has been fine and I was able to connect to my home network in wireless client mode. My router is a TP-Link TL-WR1043ND running OpenWrt 12.09 Attitude Adjustment, wifi with WPA2-AES, DHCP service.

  The Trek has been able to connect, and the whole system was running. Unfortunately, I realized, that the Trek has kept falling connections every 3-5 minutes with the genius of Netgear annoying pop up and try to re-establish a connection. Sometimes it worked, then the Trek cannot connect at all.

  Since I read that OpenWrt Attitude Adjustment can be problems with some wifi connections, I have improved my WR1043ND barrier breaker. The connection drops continued, including OSX almost every minute. The WR1043ND showed various DHCP-wifi-a failed-to-recognize-errors and in his diary.

  After trying all possible setting changes in the Trek-config (and shortly before returning the Trek), I found something as a workaround. In the Trek-config, I disabled the DHCP Server for the LAN area and assigned static IP addresses to connecting clients. Well at least so far, it seems to work very well. No more connections, no more boring engineering arise not interrupted and try to reconnect, the system seems to work.

  But for now, I'm a little confused as to the reason. In my view, the Trek connects to a hotspot and gets an IP address assigned by DHCP from hotspot. Then the Trek uses NAT to connect the clients attached to the internet. Actually the IP addresses of the DHCP assigned by the Trek to customers connected to the LAN area shouldn't affect hotspot NETWORK settings at all. Normally the IP address and private DNS settings are just for private clients LAN, aren't they? If I'm not completely wrong in my assumption, there could be a bug in the DHCP server on the hike or the way how dynamic the client LAN IPs are handled. From the point where I changed to static IP in the LAN client, there was no error message in the log of the WR1043ND.

  Strange thing... Maybe someone could correct me if my assumptions are wrong? BTW, I use the stock PR2000 Trek firmware (which is something like 1.0.0.9) since there is no other is available.

  Thank you.

  @hksteve I wish to inform you that the fix is now available from our download page.

  Feel free to update your firmware and provide feedback.

  Thank you!

• Windows XP DHCP problem when authentication network enabled

  I have a weird problem with Windows XP. Here's a few of my observations:
  -Computer Lenovo X 61 does not connect to a wireless network with a network (that is, Shared/128 b/WEP) authentication. He can never get an IP address from the DHCP server.
  -J' checked the authentication settings. They work in another computer.
  -If I give it a static IP address (less good family), it connects to the router. However, it is very slow and flaky.
  -It connects to open networks.
  -In addition, if I have a wireless and a wired connection to the computer, the wireless connection gets a quick DHCP server address. If I disconnect the wired connection, the wireless connection works perfectly.
  I tried to reinstall the NIC drivers, apply all updates for Windows and Lenovo SW and looked at the values in the Windows registry. Nothing seems to help.
  Any ideas?
  Computer is a Lenovo X 61 Windows XP Professional

  Hello

  In the past, password WEP engines were rather flaky.

  Try using the HEX string instead of the password.

  Or switch to WPA. WEP does not guarantee these days.

• Using 3500 as a Wireless Extender DHCP problem iPhone X 6

  Hello

  If all goes well, a simple question with a simple answer.

  Background:
  I stayed away from my DSL provider to a cable provider (VirginMedia). My new ISP is delivered with a modem cable (SuperHub 2 ac) and I connected the two devices together to extend my wireless home network. The cable modem, it's that the two routers are physically apart from others - connected through just their Ethernet ports - the technology of power line (Devolo dLAN 1200 +). Both routers have the same SSID broadcast, but on separate channels.

  Question:
  All devices in my house, the tablets of laptops, phones roam between the two areas wi - fi transparently * except * the iPhone 6 (iOS8.1), this works on the cable modem wi - fi, but not on the X 3500 wireless. I also have an iPad Mini 2 (also iOS8.1) which works too - aptly / wrong I have excluded iO8.1 as the issue. Oddly enough, the iPhone 6 connects to the x 3500 but isn't getting an IP address (the cable modem's DHCP server). Even if a static IP address doesn't help.

  Comments:
  If the X 3500 is configured as a DHCP server, the iPhoen connects (and gets an IP address), but then the default gateway is incorrect (gateway IP address of the X 3500 is not the modem cable remote). I can't find anywhere to specify a default gateway configuration.

  Question
  I start thinking, it is a problem with the iPhone 6 (know all other devices work correctly), but I want to just make sure I am the X 3500 configuration correctly. I am particularly interested in it if I use the right to 'Mode' ADSL / Ethernet. I tried 'Bridged Mode Only' (ADSL) and "Automatic DHCP only" (Ethernet), but does not seem to solve the problem of having the iPhone 6.

  any suggestions on how to fix / help would be most welcomed.

  Thank you!

  Thanks a lot for the details... Now I have a config that works also for the iPhone6.

  Basically, I connected the cable on the 3500 x port and the Ethernet port on the cable modem connected to the internet (via the Powerline). I then changed the network on the 3500 of 192.168.0.x x range (this is the range of network addresses used by the cable modem connected to the internet) to 192.168.168.x. Finally I activated the DHCP on the x 3500 which seemed to be the element that was killing the iPhone6.

  The iPhone6 connects now (which he always did), but with DHCP running on the x 3500 on the new range of network addresses of the iPhone 6 also get a valid IP address.

  Looks like that much just to get the iPhone 6 to work... never found a manual way to specify a default on the x 3500 gateway when you run DHCP (appears by default which is her own IP address - with no provision to change).

  Anyway... This works for now... I'll keep an eye on the iPhoen updates 6, just in case where the anomaly is something specific to the iPhone 6, if something changes I will post here.

  I have attached a picture for furture reference. Thanks again for your advice and support.

  

• How to get the IP address Linksys WRT54GS DHCP assigns to a Wi - Fi connection?

  To connect the Linksys WRT54GS to a demonstration of Microchip DV102411 WiFi Comm card I need the IP address assigned by DHCP. The Administration WRT54GS log is enabled, but there is no incoming or outgoing network activity. The DV102411 can see the SSID linsys scanning for wireless networks and attached to it but once attached, I need to know the address IP of the DV102411 has been given by the WRT54GS.

  You can consult the router DHCP client table.

• Weird Linksys x 2000 problem

  Suddenly, I was not able to connect to websites at random and do not been able to add elements of online stores to cart.  I couldn't believe the router it would, but I've confirmed.  With Linksys x 2000 installed, I tested Linkedin.com on four of my computers.  2 Windows 7 Machines, Machine 1-Windows8 and server 1-2011. After you type the user name and password, page refresh to the login screen and does not allow me to connect to.  I tested it on all 4 machines.  Also tried to order something online and not allow me to put items in the basket.  Once tested on all four machines.

  I set the router to the factory settings and tested and got the same results.  Disabled firewall and got the same results.  Ensure time was OK and got the same results. I had the latest firmware, 2.0.4 (or something like that) and no newer updates.

  I replaced the Linksys X 2000 with provided ISP router Westell 8500 and none of the problems persisited.  Definitely something wrong with the x 2000 Linksys.  I'm in the Eastern time zone and think that the problem began with Day LIght Saving time, although I can't be sure.  Routeris is good time however.  Yet once, provider ISP don't give me any problems.

  Anyone else with the same problems?

  Yes, there are a lot of discussions on this problem. The problem is that cookies are blocked. Go to the security settings on the router and check the cookie. Who's going to fix it until we get a firmware update.

• DHCP problem

  I entered the IP address of my wireless router (the one you enter the internet browser to display the parameters) and be stupid, that I disabled the DHCP. After that, I couldn't even connect to my router or go that meet. A few hours later, I managed to restart (factory reset) the router and now I can enter the address IP DHCP is on. However, again, when you start the computer, it displays the message DHCP - and these hyphens are shown. Then start windows. I wanted to re - configure the TP link router and when I run the Setup from the CD, it says that the DHCP protocol is not enabled. I don't think that the computer is still recognizing the router when connected, assuming that the DHCP is disabled for the tunnel router. I tried a static IP (not sure if I was doing it well), but don't know what to do after that. I changed back to auto, but DHCP appears again as a problem when the computer is started and all trying to install my TP Link. I'm stuck and I have no idea what to do, please explain as simply as possible, because in fact, I went in things I don't understand.

  Thanks in advance

  Hi Adriana,

  DHCP allows your computer to automatically assign an IP address to turn it off, it is not recommended, unless you have your network settings. Please follow the instructions below to ensure that DHCP is enabled:

  1. click on Start and open the control Panel.
  2. click on network and sharing Center icon.
  3 al ' View your active networks section, click on the link to connect to the Local network .
  4. in the Local area connection status window, click the Properties button.
  5. highlight the Internet Version 4 Protocol option and click the Properties button. You may need to do the following for option Protocol Internet Version 6 as well.
  6. make sure obtain an IP address automatically is selected, as well as the DNS server to obtain an address automatically.

  If that did not resolve your problem, contact your router manufacturer or your internet service provider for the correct settings.

  Please keep us updated.

  Kind regards.

• Cisco AP 561 - DHCP problems

  Hello

  We have a customer with a number of AP561, there are 2 configured SSID, IP are provided for each network via dhcp, it is managed by a switch of small business and the other is managed by a windows client server.

  The issiue is that IP address are not always given to the devices, it will work for a while then just stop, until the AP is reset, this seems to be the same for several good AP so I don't think we have any physical AP questions, it can be solved in rest normally the AP.

  I see there are other discussions with people with the same problem, we have upgraded to the latest firmware 1.1.2.3 and the problem is still happening, force wireless is not a problem because the task bar displays full strength.

  Thank you...

  Hello Sir, I am sorry that you are having this problem. The latest firmware is actually 1.2.0.2

  Please download and update your Access Points. In the release notes, it is no indication that this new firmware solves the problem:

  CSCus23303: wireless client cannot get the IP address of the DHCP server after a period of time

  Eric Moyers
  .:|:.:|:. CISCO | Pre-sale technical support of Cisco | Expert on wireless

• Linksys WUSB54GC driver problem Windows 7 64 bit - will not allow

  I have a Linksys WUSB54GC 3 Wireless Network Adapter version.  I downloaded the latest driver on the Linksys support page that says that it is fully compatible with Windows 7 64 bit.  The adapter will not allow.  After 3 grueling cat takes support sessions with Linksys, they could not understand it and threw the problem back to my Tower say it must be a problem with my Windows 7 64 bit.  I searched for Windows and Linksys support forums and some people have had luck, and others have not.  The driver has been installed manually several times as well as the removal of material, resettlement and loading the driver again and again.  I am trying to connect to my router Linksys WRT54G which has the latest firmware and has another computer wireless connected to it without any problems.  If anyone can help?

  Hello

  Have you tried the device on another computer just to be sure, does it really work?
  Have you tried another device on this computer?

  Are you logged on as ADMINISTRATOR when you do the work? Right click on the driver
  and RUN as ADMINISTRATOR?

  ----------------------------------------------------------

  References to Vista also apply to Windows 7.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -----------------------------------------------

  Then lets refresh the USB stack

  The device here is the WiFi device:

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the driver and battery USB

  This KB shows XP how to and methods of Vista and Windows 7 are the same
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer.
  as well as all USB devices that you previously used. Run Options and tick three 1
  are there choices to see if any.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• PIX from Linksys LAN 2 problems of virtual PRIVATE networks

  I have a client that replaces a router Linksys with a PIX. The Linksys is configured today with a LAN 2 LAN VPN connection to another Linksys. I enclose the Linksys configuration, but I can't get the PIX to encrypt packets to send to the Linksys site successfully, or against vice. I know that this subject has been beaten to death, but I still need help. Can someone look at the Linksys config and tell me what this requires side PIX? Thanks for any help!

  The isakmp key command you entered does two things:

  1. It identifies what pre-shared key for use with the remote peer (as both ends must use the same value) and the No.-xauth and non-config-mode say the pix as the vpn ipsec is a lan-to-lan (aka site-to-site) config and do not expect to do the authentication of the vpn RAS users. This is because the code pix can put an end to these two types of vpn on the same interface connections, so it must be able to determine when and when not to authentic additional user for ras vpn users.

  Glad that your problem has been resolved.

• SG300 and RVS4000 DHCP problems

  We recently deployed SG300-28 to replace a former 3Com switch.

  The installation program:

  In the SG300 switch router RVS400 and all workstations and server are connected.

  The problem:

  Windows 7 workstations are unable to get IP addresses of the server that is also connected to the switch.

  If, however, plug us into the workstations in the switch 4 ports on the back of the RVS4000 (the router), they get the IPs from the server without problem.

  It works perfectly with the old switch from 3Com for us it was classified in the category small business going.

  A few comments/advice appreciated! Thanks in advance!

  Pavol

  Pavol,

  Please make sure the SG300 switch running latest firmware 1.1.2.0, also new code then please switch factory reset after the upgrade. If you need assistance in upgrading please call Cisco Small Business Support Center @ 1-866-606-1866

  After upgrading please repost how these devices are connected and the configuration of your RVS4000 & SG300 switch series. Using RVS4000 for your DHCP server?

  Also make sure your RVS4000 is running latest firmware as well.

  Jasbryan

• Wireless DHCP problem

  Hello

  I have a problem

  We have cisco ap 500 series, it was light, but we have migrated to standalone, now, the scheme is simple.

  We have a 2811 router and dhcp created on this subject, we also f0/0.30 virtual interface with the ip address of 10.10.30.1

  Switch into a single interface (trunk) goes to f0/0 interface of the router, and a single interface (access) goes to ap

  The access point, we have BVI interface with 10.10.30.10 and default route to 10.10.30.1

  So when connecting to our SSID, it connect but doestn receive DHCP and APIPA address is, please explain why the ap assigns ip clients

  Also ap config.txt here

  Thank you

  Keita,

  Yes, sorry, it was not clear. Make your interface trunk switchport. You follow these steps on the switch:

  (config-if) # switchport trunk dot1q encap switch

  (config-if) # switchport mode trunk switch

  Justin

  Sent by Cisco Support technique iPhone App

• Linksys EA9500 LED problem - a solid blue line

  I had the EA9500 for a little more than a month without problems and the strong performance.

  Just yesterday, I noticed that the extreme left LED is a solid blue line on the top and the bottom of the white LED.  So the white LED is there (al that strong white LEDS is there), and above and below the left LED is a solid blue line.  It has been published.

  I restarted the router, it just comes back.

  I checked the router diagnostics and everything seems OK.  My son says that he has wireless connectivity problems, but I don't know if the two are related.

  I can't find a source to tell me what it means to the blue line.

  Any ideas?

  Thank you.

  The blue LED when the EA9500 is running indicate a device connected to MU-MIMO which is very cool and high technology.