tunnel upward but not ping of the asa inside interface

Dear all

I am establishing a tunnel vpn between cisco asa 5510 and a cisco router. The tunnel is up, and I can ping both cryptographic interfaces. Also, from the console of the asa I can ping to the router lan interface but the router I can not ping the lan interface of the asa, this message appears in the log

% ASA-3-713042: unable to find political initiator IKE: Intf liaison_BLR, Src: 128.2

23.125.232, DST: 129.223.123.234

Here is the config of the equipment.

I was able to successfully establish an ipsec with an another ROUTER 1841 tunnel. I have 1 hub site and 3 remotes sites with asa as a hub.

Help, please.

Your crypto that ACLs are not matching. They must be exact mirror of the other.

In addition, you can consider setting the levels of security for the interfaces. They are all at 0. The value internal/private those a higher value.

Let me know how it goes.

PS. If you find this article useful, please note it.

Tags: Cisco Security

Similar Questions

IPSec Tunnel upward, but not accessible from local networks

Hello

I have an ASA5520 and a Snapgear. The IPSec tunnel is in place and works very well. But I am not able to access the local LAN on both sides. Here are a few setups:

SH crypt isakmp his

Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey) Total IKE SA: 1 1 IKE Peer: 10.10.10.2 Type : L2L Role : responder Rekey : no State : AM_ACTIVE

Crypto/isakmp:

crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto map IPSECTEST_map0 1 match address IPSECTEST_cryptomap crypto map IPSECTEST_map0 1 set peer 10.10.10.2 crypto map IPSECTEST_map0 1 set transform-set ESP-3DES-SHA crypto map IPSECTEST_map0 1 set nat-t-disable crypto map IPSECTEST_map0 1 set phase1-mode aggressive crypto map IPSECTEST_map0 interface IPSECTEST crypto isakmp enable outside crypto isakmp enable IPSECTEST crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 3600

Route SH:

C 172.16.3.0 255.255.255.0 is directly connected, VLAN10 C 10.10.10.0 255.255.255.0 is directly connected, IPSECTEST C 192.168.112.0 255.255.254.0 is directly connected, inside

access-list:

IPSECTEST_cryptomap list extended access allowed object-group DM_INLINE_PROTOCOL_1 172.16.3.0 255.255.255.0 object 172.20.20.0

and here's the scenario:

If I make a ping of the asa to the Remote LAN, I got this:

ciscoasa (config) # ping 172.20.20.1
Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 10.172.20.20.1, wait time is 2 seconds:
No route to the host 172.20.20.1

Success rate is 0% (0/1)

No idea what I lack?

Here's how to set up NAT ASA 8.3 exemption:

network object obj - 172.16.3.0
172.16.3.0 subnet 255.255.255.0

network object obj - 172.20.20.0
172.20.20.0 subnet 255.255.255.0

NAT (inside, outside) source static obj - 172.16.3.0 obj - 172.16.3.0 destination static obj - 172.20.20.0 obj - 172.20.20.0

Here's how it looks to the ASA 8.2 and below:

Inside_nat0_outbound to access extended list ip 172.16.3.0 allow 255.255.255.0 172.20.20.0 255.255.255.0
NAT (inside) 0-list of access Inside_nat0_outbound

Tunnel upward, but cannot Ping

I've set up a tunnel to an ASA called SALMONARM to a Cisco 1921 called PG-1921.

I raise the tunnel by sending a part of traffic 'interesting '.

PG-1921, I run isakmp crypto to show its, and an entrance to the tunnel is present, with the status ACTIVE.

I do the same on SALMONARM, and once again the tunnel is present, with the MM_ACTIVEState.

So far so good.

I try to send pings from the inside of the SALMONARM network within the network PG-1921 .

Pings do not (time out).

I run the crypto ipsec its peer view SALMONARM, and I see program 0 and 0 decaps.

This seems to suggest that the pings never leave SALMONARM ASA.

I believe that I was NAT exemption and an ACL to allow traffic for the remote network from internal.

Here's the configs...
SALMONARM (ASA): http://pastebin.com/raw.php?i=vYDhfe3r
PG-1921 (1921 Cisco): http://pastebin.com/raw.php?i=L6aYhmc9

The tunnel is crypto map PG_TUNNEL_MAP 11 in the config SALMONARM and crypto map SDM_CMAP_1 5 in the config of PG-1921 .

What might be missing?

You have a router behind the ASA that could have bad roads in there? Are you ping of the SAA itself or a device behind him? Can you add the command 'inside access management' and try to ping of the asa with the command "ping inside x.x.x.x" and see if you get the program then?

Thank you

Mike

can read but not write in the Numbers worksheet

Can read but not write in the worksheet Numbers on my MacBook.

Hi Frederic,.

This also happens if you are still in the screenshot. Is there a "Done" down button on the right?

Quinn

HP ENVY 17-j113tx TouchSmart: Bluetooth paired but NOT connected to the device

Bluetooth paired but NOT connected to the device - question - Upload of files from device to PC fails.

Description of the problem
- Download a file from PC (Win10 x 64) for Android phone has worked well.
- Download the same file from the phone on PC (Win 10 x 64) - FAILURE.
Someone knows how to deal with this issue, provide a work around...?

I have way too much time on my hands right now...!

Treatment

of the Assembly's strong name validation failed "c:\windows\ehome\ehshell.exr". The file may have been tampered with or it was partially signed but not totally witht the

media center ehshell.exe received the error message 205 units

of the Assembly's strong name validation failed "c:\windows\ehome\ehshell.exr". The file may have been tampered with or has been partially registered, but not totally witht the private key

After you have installed the XP SP3.

How can I fix this error.

Media Center worked fine until I installed SP3.

Hello

I imagine the inconvenience that you have experienced, but don't worry, we are here to help solve the problem and guide you in the right direction.

Ehshell.exe is a Windows system file that is used to run Microsoft Media Center. It is not a critical system file. However, the ehshell.exe file can become infected and cause errors trying to run certain programs. If the ehshell.exe is absent, it can also cause errors. Reinstall a clean copy of ehshell.exe with the Microsoft System Restore.

(a) click on the "Start" menu, then click on "programs". Scroll down and click on "Accessories," then "system tools." Click "System Restore."

(b) click on 'Next' in the system restore window to view a list of points of restoration which has been archived.

(c) select a restore point created before the ehshell.exe file becomes corrupt or got deleted. If no restore point until this time is listed, click on "Show restore points more" to select the one that is before this date. Click 'Next' to choose which restore point.

(d) click on 'Finish' to start the system restore. The computer will restart once the process is complete and the ehshell.exe file is reinstalled.

If the problem persists, follow these steps:

You try to run the following commands to re-register all Media Center services:

(a) close Media Center

(b) click on the start menu, choose run and type cmd , and then press ENTER.

(c) in the command prompt, run the following commands to type (or copy/paste) the one at a time and press on enter:

· Regsvr32.exe atl.dl

· C:\WINDOWS\eHome\ehl Sched /unregServer

· C:\WINDOWS\eHome\ehSched/service

· C:\WINDOWS\eHome\ehRecvr /unregServer

· C:\WINDOWS\eHome\ehRecvr/service

· C:\WINDOWS\eHome\ehRec.exe /unregServer

· C:\WINDOWS\eHome\ehRec.exe/regserver

· C:\WINDOWS\eHome\ehmsas.exe /unregServer

· C:\WINDOWS\eHome\ehmsas.exe/regserver

· Restart the Media Center

Hope this helps and let us know if you need more assistance. We will be happy to help you.

Huawei Sonic is recognized in devices and printers, and shows paired but not connected in the settings on the phone.

Original title:

Try to connect Huawei Sonic to win7x64 pro edition using bluetooth. Huawei Sonic is recognized in devices and printers, and shows paired but not connected in the settings on the phone. How do I overcame the problem of connection I want to transfer photos from phone to PC?

Hello

1. are you able to communicate and share with other Bluetooth devices?

2. what happens when you transfer files?

3. do you get an error message?

4 you did changes to the computer, before the show?

Method 1:

Connect the phone to another computer and check.

Method 2:

If you are unable to connect to another computer, you can contact the manufacturer of the phone and check.

http://support.Huawei.com/support/

How to restore pictures that have been deleted from Lightroom, but not removed from the 'drive '?

How to restore pictures that have been deleted from Lightroom, but not removed from the 'drive '? Also, how can I restore photos after saving Lightroom. I started to remove some files and it removed ALL of them! I chose the option "cancel delete files" and them brought back, she says they are all "missing or offline. I tried to 'find' a different folder and it deleted the folder all together and now I don't know where he is. Help, please!

How to restore pictures that have been deleted from Lightroom, but not removed from the 'drive '?

You need a backup of your Lightroom catalog file before deleting the photos made. You have such a backup? If so, find the backup catalog, open it (double click on it) and then search for the photos you want and select them and then file-> export catalogue; Then go to your original catalog file, open it and select file-> import from another catalog and points to the catalog that you just exported.

If you do not have a backup of your catalog file, then the only thing you can do is to import the photos again, and Lightroom will treat them as totally new photos with no editing and no metadata provided by the user.

Moreover, the idea of importing photos into Lightroom and then later removing them to Lightroom should is limited to photos you will EVER want such a photos that are so overexposed or underexposed or blurred that they are essentially useless. The photos that you care enough to run a task on (including editing) should never be removed from Lightroom.

Also, how can I restore photos after saving Lightroom.

Is this the same problem as above, or another?

I chose the option "cancel delete files" and them brought back, she says they are all "missing or offline.

Is it possible that you actually deleted pictures from the hard disk, as well as from Lightroom? Anyway, Lightroom cannot find the photos and you first need to find photos on your hard drives and then direct Lightroom to the location of the photo on your hard drive, using these instructions Adobe Lightroom - find folders and files moved or missing

Can the interface of management firepower & ASA-Inside interface be on separate subnet?

HI -.

Need a few more details, please.

I have a requirment needed to put the power of fire management interface and the interface of the ASA-Inside on different subnets, supports?

From what I've read so far, most of the document suggests to put two interfaces on the same subnet, is there a reason to do so?

I may be wrong but I think that fire use management interface to communicate with FireSight for control and comamnd traffic, data traffic real plan always flows from ASA-outside to inside and vice versa, both there are connectivity ip between FireSight and firepower, it should be ok, right? or am I totally wrong, that they must be on the same subnet?

ASA5515-x with the firepower 5.3.1

Thanks in advance for your help.

Separate subnets are fine.

As you have seen correctly - the module of firepower has need to contact FireSIGHT Management Center (IP-wise).

This path is completely independent of the plan through the ASA data path. The ASA redirects the traffic via the service strategy for the module of firepower entirely internally to the unit.

Site to site VPN upward but not pass traffic (ASA 5505 8.3.1 and 9.2.3 version)

Hello

I'll put up a tunnel vpn site-to-site between two locations. Both have cisco ASA 5505 running a different version, I'll explain in more detail below. so far, I was able to get the tunnel to come but I can't seem to pass traffic, I work at this for days now and have not been able to understand why he will not pass traffic. Needless to say that the customer's PO would be on the fact that their VPN is not upward and they had to do by hand. I'll put the configs below, if possible can someone help me as soon as POSSIBLE, I really want to get this site up and running so that we do not lose the customer.

An IP address of 0.0.0.0 = site
Site B IP = 1.1.1.1

A Version of the site = 8.3.1
Version of the site B = 9.2.3

__________________________

_________

A RACE OF THE SITE CONFIGURATION

Output of the command: "sh run".

: Saved
:
ASA Version 8.3 (1)
!
hostname SDMCLNASA01
SDMCLNASA01 domain name. LOCAL
Select 5E8js/Fs7qxjxWdp of encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
the IP 0.0.0.0 255.255.255.252
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
SDMCLNASA01 domain name. LOCAL
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_192.168.0.0_24 object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
network lan_internal object
192.168.0.0 subnet 255.255.255.0
purpose of the smtp network
Home 192.168.0.245
Network http object
Home 192.168.0.245
rdp network object
Home 192.168.0.245
network ssl object
Home 192.168.0.245
network camera_1 object
host 192.168.0.13
network camerahttp object
host 192.168.0.13
service object 8081
source eq 8081 destination eq 8081 tcp service
Dvr description
network camera-http object
host 192.168.0.13
network dvr-http object
host 192.168.0.13
network dvr-mediaport object
host 192.168.0.13
object-group Protocol DM_INLINE_PROTOCOL_1
object-protocol udp
object-tcp protocol
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
DM_INLINE_TCP_2 tcp service object-group
port-object eq 34567
port-object eq 34599
EQ port 8081 object
permit access ip 192.168.0.0 scope list outside_1_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0
outside_access_in list extended access permit tcp any any eq smtp
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_2 object-group
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
!

network lan_internal object
NAT dynamic interface (indoor, outdoor)
purpose of the smtp network
NAT (all, outside) interface static tcp smtp smtp service
Network http object
NAT (all, outside) interface static tcp www www service
rdp network object
NAT (all, outside) interface static service tcp 3389 3389
network ssl object
NAT (all, outside) interface static tcp https https service
network dvr-http object
NAT (all, outside) interface static 8081 8081 tcp service
network dvr-mediaport object
NAT (all, outside) interface static 34567 34567 tcp service
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 71.42.194.209 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
http server enable 8080
http 192.168.0.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 outside
http 71.40.221.136 255.255.255.252 inside
http 71.40.221.136 255.255.255.252 outside
http 192.168.0.0 255.255.255.0 outside
http 97.79.197.42 255.255.255.255 inside
http 97.79.197.42 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set peer 1.1.1.1
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.0.50 - 192.168.0.150 inside
dhcpd dns 192.168.0.245 209.18.47.62 interface inside
dhcpd SDMCLNASA01 field. LOCAL inside interface
dhcpd allow inside
!

a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared key *.
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
!
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:462428c25e9748896e98863f2d8aeee7
: end

________________________________

SITE B RUNNING CONFIG

Output of the command: "sh run".

: Saved
:
: Serial number: JMX1635Z1BV
: Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
:
ASA Version 9.2 (3)
!
ciscoasa hostname
activate qddbwnZVxqYXToV9 encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 1.1.1.1 255.255.255.252
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network camera_http object
host 192.168.1.13
network camera_media object
host 192.168.1.13
network of the NETWORK_OBJ_192.168.0.0_24 object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
outside_access_in list extended access permit tcp any any eq 9000
outside_access_in list extended access permit tcp any any eq www
outside_access_in list extended access permit icmp any one
outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object NETWORK_OBJ_192.168.0.0_24
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 732.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
!
network camera_http object
NAT (all, outside) interface static tcp www www service
network camera_media object
NAT (all, outside) interface static 9000 9000 tcp service
!
NAT source auto after (indoor, outdoor) dynamic one interface
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 71.40.221.137 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 peer set 0.0.0.0
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev1 allow outside
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0

dhcpd address 192.168.1.50 - 192.168.1.150 inside
dhcpd dns 192.168.0.245 209.18.47.61 interface inside
dhcpd SDPHARR field. LOCAL inside interface
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol
internal GroupPolicy_0.0.0.0 group strategy
attributes of Group Policy GroupPolicy_0.0.0.0
VPN-tunnel-Protocol ikev1, ikev2
tunnel-group 0.0.0.0 type ipsec-l2l
tunnel-group 0.0.0.0 ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
!
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:19031ab1e3bae21d7cc8319fb7ecf0eb
: end
Sorry my mistake.

Delete this if it's still there

card crypto external_map 1 the value reverse-road

Add this to both sides

card crypto outside_map 1 the value reverse-road

Sorry about that.

Mike

Windows Vista computer connects to the internet, but not ping to auto DHCP name

Trying to get my Vista machine to have the file and printer sharing, I can see attached machines, and they can see the Vista machine, but does not connect to the computer. The Vista machine will not see public folders with error code: 0 x 80070035 the network path was not found.

Ping the DHCP name provides:

Main2 ping [fe80::12:f74:b94e:94fb 8%] of 8% with 32 fe80::12:f74:b94e:94fb
YTES of data:
General failure.
General failure.
General failure.
General failure.

Ping statistics for fe80::12:f74:b94e:94fb 8%:
Packets: Sent = 4, received = 0, lost = 4 (100% loss),

Ipconfig/all

Windows IP configuration

Name of the host...: Main2
Primary Dns suffix...:
Node... type: hybrid
Active... IP routing: No.
Active... proxy WINS: No.

Wireless network connection Wireless LAN adapter:

The connection-specific DNS suffix. :
... Description: Belkin Wireless G Desktop Card
Physical address.... : 00-11-50-D6-32-97
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Address IPv6 local link...: fe80::e497:9802:e6a6:40ce % 10 (Preferred)
IPv4 address: 192.168.2.7 (Preferred)
... Subnet mask: 255.255.255.0.
Lease obtained...: Tuesday, October 21, 2008 23:06:50
End of the lease...: Thursday, October 23, 2008 11:06:50
... Default gateway. : 192.168.2.1.
DHCP server...: 192.168.2.1.
DNS servers...: 192.168.2.1.
NetBIOS over TCP/IP...: enabled

Card tunnel Local Area Connection * 6:

The connection-specific DNS suffix. :
... Description: Teredo Tunneling Pseudo-Interface
Physical address.... : 02-00-54-55-4E-01
DHCP active...: No.
Autoconfiguration enabled...: Yes
IPv6 address: 2001:0:4137:9e50:12:f74:b94e:94fb (area
ED)
Address IPv6 local link...: fe80::12:f74:b94e:94fb %8 (Preferred)
... Default gateway. : ::
NetBIOS over TCP/IP...: disabled

Card tunnel Local Area Connection * 7:

State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: isatap. {E71A931D-A587-49DD-BF49-209236344
523}
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes

Any help?

Call the Web browser program compiles in 4.2 and upward but not 4.1

I wrote a very simple application that when launched, opens the browser and takes you to a predefined binding. The following code compiles and works very well on the 4.2 and upward, but I can't seem to compile in the jde 4.1:

package vwr;

import net.rim.blackberry.api.browser.Browser;
import net.rim.blackberry.api.browser.BrowserSession;
import net.rim.device.api.ui.UiApplication;

public class vwr extends UiApplication {
public static void main(String[] args){
vwr instance = new vwr();
instance.enterEventDispatcher();
}

public vwr() {
BrowserSession site = Browser.getDefaultSession();
site.displayPage("http://www.google.com");
site.showBrowser();
System.exit(0);
}
}

When I compile 4.1, I get an error related to the site.showBrowser (); command. But as I mentioned, the above code compiles and works fine on OS 4.2 and above. Is there a simple solution for this?

Thank you in advance.

Nevermind, I found a solution that works. Here's the code. I hope that someone else will find useful.

import net.rim.blackberry.api.browser.Browser;
import net.rim.blackberry.api.browser.BrowserSession;
import net.rim.device.api.ui.UiApplication;

public class vwr extends UiApplication {
public static void main(String[] args) {
     vwr instance = new vwr();
     instance.enterEventDispatcher();
  }

public vwr() {
    BrowserSession site = Browser.getDefaultSession();
    site.displayPage("www.google.com");
    System.exit(0);
  }
}

Can not handle the ASA inside the interface of Site to Site VPN

Hi all

I was deploying new site to site between ASA 8.0 (HQ) and ASA 8.4 (branch). Everything works fine but I have a problem on the ASA-reach remote that I can't manage branch ASA with inside the interface IP address.

My setup on remote ASA

management-access inside

ICMP allow any inside

SSH 0.0.0.0 0.0.0.0 inside

SNMP-server host inside 10.0.1.101 communitry test-snmp version 2 c

My Test

-ping of the AC for inside the interface of remote ASA
- Client time-out see demand
- When debug icmp on ASA remote then ASA show only ICMP request to HQ no response back from remote ASA
I'm not sure whether it's a bug on ASA 8.4 or not because I can manage a remote other ASA what version 8.0 software HQ

Thanks in advance

Do not know what 8.4 version you use, but it is broken in the 8.4 (2), I stumbled upon the upgrade from same problem. SSH and ASDM will not connect through a VPN L2L interface inside. This worked well in 8.4 (1).

CSCtr16184

http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtr16184

[email protected] / * /.

Ipad Cisco ipsec VPN connects but not access to the local network

Hi guys,.

I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.

If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.

Cisco 877.

My config is attached.

Any ideas?

Thank you

Build-in iPad-client is not useful to your configuration.

You have three options:

(1) remove the ACL of your vpn group. Without split tunneling client will work.

2) migrate legacy config crypto-map style. Here, you can use split tunneling

3) migrate AnyConnect.

The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.

virtul machines not ping to the host machine?

Thanks for the reply and solve my prob...
now I m command ping with the host computer to the my virtual machines these are pinging...
but virtual machines don't ping not to host the computer why?
Please answer me help me...

Welcome to the community,

What is the operating system on the host computer. In the case for example of Windows 7, you may need to allow ICMP (ping) in Windows Firewall.

André

tunnel upward but not ping of the asa inside interface

Similar Questions

Maybe you are looking for