UCS C200 M2 - screw drive plate?

Similar Questions

• Replacing hard drive RAID 10 (UCS-C200-M2)

  Guys,

  I'm running RAID10 on UCS C200 M2 and exchanged one of the defective drive.

  Currently, there is beep for more than 12 hours and I guess that the new drive is under reconstruction at the moment.

  In addition, physical drive status is currently on "not well configured" on CIMC. The status changes to "online" after

  the reconstruction end? Will be required reboot when the rebuild is complete?

  Please advice.

  Hello

  If the State of the reader to not configured well. You will need access to the Webbios to change online status and allow reconstruction to be undertaken.

  You will find here all the information required to set the drive to the State once again

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/c/SW/RAID/con...

  If by chance you encounter any problem do such thing. Call the TAC and they will help out you with it.

  Please note ALL useful answers

• UCS C200 RAID solution

  Hello

  I hope for your help about the technical question about the RAID.

  We bought a server in a rack of Cisco UCS C200. Now I looking for information on the best RAID solution in our case.

  The question:

  As I understand it, there is an integrated RAID solution: Intel ICH10R in UCS C200 server. We use this RAID configuration now and it works OK. However, we wonder if it is worth installing the PCIe controller (we have HP Smart Array P410 (ATA/dis2) card). We use currently 4 SATA and RAID drives works as expected, but we are interested in, if there are all the advantages of the separate RAID controller card. Above all, we are interested of performance benefits as we plan to have a lot of disk writes (records call - about 10-20 calls per hour, lasting 2 minutes on average). We would be happy to stay with RAID integrated if it works stable. On the other hand, we will install the above mentioned Intel RAID card if you say that it would be the best solution about the reliability and wear of the disc.

  I would be grateful for any comments.

  Kind regards

  Vytas

  Vytas,

  Your question is probably down to RAID levels supported for each card.  The performance of each should be relavitley the same, so I would not concentrate on that.

  The only supported RAID controllers are listed here and must be purchased from Cisco:

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/HW/C200M1/install/RAID.html#wp1015625

  "Others' work, but you'd be yourself if you encountered problems with TAC.

  The integrated Intel ICH10R card supports up to four SATA using RAID0 (striped) or RAID1 (mirror) drives.

  If you need one RAID5, 10 or more, then you must a MegaRAID controller to do.

  All RAID controllers provided by Cisco are heavily on trial and could be your best option for reliability and performance.

  Kind regards

  Robert

• HP EliteDesk 800 G2: HP EliteDesk 800 G2 2.5 inch screw drive

  Where can I get screws drive 2.5 inches.  They are distinguished by the 3.5 inch mounting screws.  These should be shock resistant mounting screws.

  I can't believe that it was so difficult for an answer.  I found that they use the isolation to drive screws 2.5 "on the recent series of mini EliteDesk.

  The correct answer is:

  HP part # 594220-001 - past - son of insulation of hard drive (blue color)

  They are difficult to find than the 3.5 "drive of isolation living in the after-market.

  Have a great day everyone.

• Changes made to the screw driver in the Interface of Simulation Toolkit (SIT) are not translated

  Hello

  I use Simulation Interface Toolkit to target a controller built in Simulink on a PXI target. I used the SIT connection manager to generate the driver screws I had to make some changes in the screw driver specifically Read.vi IO. I made the changes and the entire application runs without error. But the changes are not getting in the functioning of the application, essentially when I load the thing on PXI and run it, it contains exactly as it was before behaiving I made these changes. Some how the changes I make to the Read.vi of e/s are not begin day somewhere in the top vi driver.

  Could someone help me with this please.

  Eliane.

  Hi Bill,

  Thank you very much for looking into this. Solved the problem.

  The problem was that whenever it makes a change one driver that saw VI top-level driver must be opened and saved again. This opening and registration links the pilot with new changed correctly VI and then everything works fine.

  Thanks again.

  Eliane.

• UCS C200 and NIC Teaming/FailOver

  As UCS C200 with management of a 10/100 and 10/100/two interface 1000 interfaces and PCIe with 4NIC

  I want to install CUCM 8.5 is the NIC Teaming/failover supported by UCS C200 and how to set up the NIC Managment interface with failover?

  Thank you.

  Hello

  As you install apps from the CPU on the server of the UCS, speech application team listed their recommendations here.

  http://docwiki.Cisco.com/wiki/QoS_Design_Considerations_for_Virtual_UC_with_UCS#Guidelines_for_Physical_LAN_Links.2C_Trunking_and_Traffic_Sizing

  You can create a NIC teaming in the ESXi via vSphere client software for traffic from from / destined for virtual machines.

  For C200, we have only one management port and if you use the management for MMIC traffic port, switch option is not available.

  However, if you choose to use host for MMIC traffic NETWORK ports, you can set up CIMC NIC mode for 'LOM shared' which provides the NIC teaming options.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/SW/GUI/config/Guide/1.4.1/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_141_chapter_01000.html#concept_AC4EC4E9FA3F4536A26BAD49734F23D0

  HTH

  Padma

• CISCO UCS C200 M2 amber display clear on mem and warning

  Hello

  My company bought 5 units of CISCO UCS C200 M2. The servers are equipped with 2 x 6 core 2.67 GHz. The server was also equipped with 32 GB of ram. One of the shows Server alert light yellow on mem and warning on the front panel. Can someone tell what could possibly cause this problem?

  Thank you

  Logan

  Hi Steve,.

  There could be a faulty MEMORY Strip on the system, in the MMIC, you can check the logs SALT (System event log) that will provide you with more details.

  I give advice you open a TAC case for this, we can take a look at the tech show and understand why accurate and if necessary replace the defective DIMM module / part (if defective).

  Thank you!

  . / Afonso

• UCS C200 M2 R200 - 1120402W Nic will negotiate only 100 MB full

  We have a new UCS C200 M2 server running ESXi 5.0.0 and will be only neg a speed of 100 MB - tried to connect a GLC - T on a 3750 and also Port copper on 2960G - same result.

  Trying hard value speed 1000 in vSphere client produced an error:

  Call 'HostNetworkSystem.UpdatePhysicalNicLinkSpeed' to object 'networkSystem"on ESXi '172.19.99.103' failed.

  Operation failed, the diagnostic report: forcing 1000Mbps or faster may not be supported on this network device, please use autonegotiation call 'HostNetworkSystem.UpdatePhysicalNicLinkSpeed' to object 'networkSystem"on ESXi '172.19.99.103' failed.
  Operation failed, the diagnostic report: forcing 1000Mbps or faster may not be supported on this network device, use rather auto-negotiation

  Adapter is Intel 82576 Gigabit Network Connection

  Just use HUU to version 1.4 - no improvement.

  Thoughts, suggestions?

  Gordon,

  Can you please share the output of following ESXi

  VMware - v

  esxcfg-NICS - l

  ethool-i vmincX

  Do you see the same behavior with the other ports of the NETWORK adapter on the server?

  Padma

• UCS C200 Server Power Supply Question

  We make some changes in our data center and which involves electric grid.  We had to replace our Dustribution of power rack and to respond to the charge, we moved 208V, 3 phase power distribution.  Read the literature, I see that the power supply to the UCS C200 servers can operate 115V to 230V AC.

  My questions are: is it everything I have on power supply from 120V AC 208 v power supply power supply power supply?  Can I have a power running at 120 v and the other operating at 208V?  I try to avoid the closure of the server.

  According to specifications

  http://www.Cisco.com/c/dam/en/us/products/collateral/servers-unified-com...

  Table 41 UCS C220 M3 SFF 450w Power Supply Specificationspescription
  Input AC voltage
  90 to 264 VAC auto-ranging,
  100 to 120 VAC nominal
  200 to 240 VAC nominal

• UCS C200 M2 could not start

  Hi all

  My Cisco UCS C200 could not start. Once checked, I found that the problem is the raid controller, the card may not work properly.

  the type of raid used controller is LSI MegaRAID 9260-4i

  can I replace this controller card with different types such as LSI MegaRAID 9260-8i

  If can, what should I do? are there concerns?

  Thank you for your kindness

  That should be fine.  See the documentation of the TA on the exact process of swapping the controller, but since they are of the same generation, just different port internal account (4 vs 8) and all RAID information is stored on the discs themselves, you should have no problem exchange controllers and imports of table on the new controller.  Once swap you controllers, host of startup, enter the optional ROM of LSI and check if the table is waiting for import (if she is not the automatic import).

  Kind regards

  Robert

• MMIC UCS C200 M2 blade - cannot access

  Hi all

  I was hoping someone in this forum could help with a problem I have on a customer site. We have therefore two blades UCS C200 M2 we cannot access MMIC of. When I try to reach the IP address, the browser just sits there, but the IP address is an echo request ICMP who responded. I rebooted a systems press F2 and tried to launch the utility BIOS Setup MMIC but received a message "no attention not found" and the only option was to hit very well.

  What would cause this? And should I update the firmware? If I need to update the firmware how can I go about this...?

  In addition, these systems are running ESXi 4.1, but I believe that the version of VMware is not compatible. Could someone help me confirm this?

  Any help is greatly appreciated!

  -Bobby

  Hello

  It worked before?

  If this is not the case, try resetting the MMIC or it could be a browser/java problem too. The problem exists across the browser and several pc user.

  See doc below to configure the Mmic

  http://www.Cisco.com/c/en/us/support/docs/servers-unified-computing/UCS-...

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/c/SW/CLI/CONF...

  -
  Siva

• UCS C240 M3 "hard drive not found."

  Hello world.

  I have a UCS C240 M3 for a demo with the following equipment.

  UCS C240 M3 SFF2 1x8GB 1xE5-2609 ROM55 2x650W SD RAILS

  SMARTNET 8X5XNBD UCS C240 M3 S2 Server-SFF

  E5-2609/80W 4 c/10 MB of 2.4 GHz Cache/DDR3 1066 MHz

  Rank of 8 GB DDR3-1600-MHz RDIMMS/PC3-12800/dual / 1.35v

  Power cord 250VAC 10A CEE 7/7 plug EU

  Shutter Panel UCS 2.5 inches HDD

  Heatsink for UCS C240 M3 Rack Server

  Standard height PCIe dispenser for C-series

  Low-profile PCIe dispenser for UCS

  Power 650W for C-series rack servers

  Embedded SW RAID 0, 1, 10, 5 8 ports SAS/SATA

  2U Kit rails for the UCS C-Series servers

  16 GB SD card module for servers C240

  In addition, these HD.

  300 GB, 6 GB SAS 10 K RPM SFF HDD/sled hot plug/mounted disk x 2

  I pluged the HDs to the Bay of 1 and 2, but the system says "Hard Drive not found" so it doesn't allow me all RAID configurations.

  Each LED on the HD and the server is green so aparently all is ok.

  The firmware is 1.4 (6)

  Any ideas?

  Thank you.

  Best regards

  Hello

  Please check if the cables are connect integrated RAID controller and the appropriate ports on the back plane.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/HW/C240/install/RAID.html#wp1017441

  What happens when you start as an option ROM RAID controller? What is it recognizes hard drives?

  Padma

• UCS C200 M2 with 1064E - not possible to the raid configuration

  Hello world

  I have a C200 M2 with a two and 1064E SAS drives raid controller, but I'm not able to configure a raid 1. I installed the firmware 1.4(3k). Please see attachments for more information.

  Someone that never had the same problems?

  Thanks in advance and best regards

  Dominic

  Information:

  

  

  

  

  

  

  

  Hi Dominic,

  You went in the F2 bios at startup and all pcie slots have been created for the disabled no.?  There is another bug were you must shoot all pci cards to set up the raid, but I think it's rained long you run in)

  ( http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtz63555&from=summary).

• execution of the RT custom device screw driver

  Hi all

  I'm building a custom device in which I expect a user input. (user provides entries on the home page of the custom device).

  Once the entry is expected on this basis I read the file-specific data and creating channels and article.

  Previously creating channels and article I in the initailiazation code.  But now that I'm waiting for user input I can't create these channels during initialization (reason is before getting the input channels will be created which I don't want. My creation of channel depends on the intervention of the user).

  If this logic of formation of channel I now write in pilot RT VI with my main logic of the reading and writing of the channels. For this I just want to know what exactly is the RT pilot VI begins its execution?

  If the RT Vi driver starts to run after adding the deivce custom veristand and after giving the user input and then my purpose will be resolved.

  I hope I explained my question correctly.

  The pilot begins after the definition of the system is deployed.  I don't think you can add strings in VI driver.  Nor do I think that you want, because you won't have an interface for them in the system definition.  Without a channel interface, i.e. mapping, how do you get data in and out of them?  I think your plan to create channels based on user input and data configuration are fine.  I suggest that you implement in the homepage or pages on the main page.

  -Steve K

• UCS C200 with Adaptec ASR-2405

  Hi all

  Our customer buy a C200 server and now he wants to put the controller RAID Adaptec ASR-2405, but this controller will not work.

  Is there a reason that RAID control does not work?

  Can you give me other tables with supported third-party RAID controllers?

  According to the version of the firmware, choose the appropriate document in this link.  This will tell you what hardware and software is supported.

  http://www.Cisco.com/en/us/products/ps10477/prod_technical_reference_list.html