Unable to connect to a network, even with the right password

Similar Questions

• Protected dmg will not open, even with the RIGHT password

  I created a password protected DMG, and now this record does not, although I am sure that I use the password. After entering the PW, I get a message indicating that the password is incorrect: ' try again - please enter the password to access the [FolderName] .dmg files»     Yesterday it was fine, and I use it every day from the folder.

  Yesterday I was accessing the DMG over LAN. Perhaps a corruption that happened then. The password does not also work on the same Time Machine recovered file DMGs, be saved.

  Other messages, I understand that using the console to get a newspaper might be useful, so I (think) I don't have that. What I believe to be the relevant lines produced when I tried to open the file is here:

  16/12/15 7:19:48.541 PM SecurityAgent [942]: failed to initialize the named IconCache: com.apple.iconservices with error: error Domain = NSCocoaErrorDomain Code 4097 = "could not connect with a helper." (connecting to the service named com.apple.iconservices) UserInfo = 0x7fccb3712a90 {NSDebugDescription = connection to the service named com.apple.iconservices}

  16/12/15 7:19:48.543 PM SecurityAgent [942]: error returned by iconservicesagent: Domain = NSCocoaErrorDomain Code error 4097 = "could not connect with a helper." (connecting to the service named com.apple.iconservices) UserInfo = 0x7fccb3721040 {NSDebugDescription = connection to the service named com.apple.iconservices}

  My system is Yosemitte 10.10.5.

  Does anyone have any ideas on how I can access my files again?

  Thank you

  -Tw

  UH... stupid. I'm sorry, I just cheated on my password. It's good, nufin is false, and it was the just operator error.

  .. . How can I delete these messages?

  This forum is anonymous?

  Ugh lame, sorry

• Unable to connect to a network or to the Internet on my Dell XPS1530.

  Unable to connect to a network or to the Internet on my Dell XPS1530. When I try to diagnose problem, I get a message that reads "Network Diagnostics cannot run because the Diagnostics Policy Service is not running." Having exhausted the patience all the phone with my IP and Dell, which tells me that it is a problem of Microsoft software. I have two other computers and a PS3, and I am able to connect to the Internet through one any of them. The XPS works under Vista with SP2. Can someone help, please? Thank you.

  Go to start / Control Panel / Administrative Tools / Services and go to diagnostic policy Service and set it to automatic and start it.  If it does not start, check the dependencies and make sure they're too automatic and rnning.  Then see if you can run Network Diagnostics.

  You can get in trouble with your device drivers.  Go to Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you should get those developed to date for the network card and regardless of the device you use to connect (such as a router wireless or such) and all you have time to do - they can help way beyond simply solve this problem), let the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.

  When I'm in a lke your situation, I usually start from scratch.  Create a new network connection by ensuring that all settings are correct.  Check all the cables (if there is).  You have already reinstalled the drivers - make sure that no firmware or software is also necessary.  Configure the network sharing settings and make sure that you are ready to discover the network and such.  Check other computers to see their settings to make sure you get yours right and essentially the same thing (the same exatly so is another Vista machine connected in the same way).  Go to start / Control Panel / Internet settings and make sure that it's too fixed properly.  To connect, then try again. If this is not the case, remove some time to cool down and then start again with another new connection.  It's almost certainly a parameter that is not correcct (something no doubt very simple).

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Laptop unable to connect to a network printer with WRT54GL Wireless

  Recently, I replaced an old router with a WRT54GL. Initially, I had the installation of the network without security and my PC and laptop had no problem connecting to the printer (Samsung CLP-600N). After that I enabled the security, the laptop can not send jobs to the printer. The discovery software that comes with the printer can find it; It can not all just print to it. My PC (wired LAN) allows to print, but not the laptop wireless.

  As you already know the IP address of the printer, then you need to manually add the printer on your computer port. What is the operating system installed on your computer?

  You can follow this link to add ports on your computer, its for windows 7.

  If its windows Vista, you can follow this link.

• want dv6-7214 will connect without Wireless - N, even with the replacement of the wifi card.

  Two routers, linksys e3000 and dlink dap1522, both running only thread-802 n wap2 personal

  (also fails with encryption disabled)

  HP dv6-7214 will connect or wireless-N.

  Other wireless-n devices all connected, like the samsung galaxy, sony viao vista.

  Dialog Configuration-protected connection recognizes WPS-Wireless wifi connect info, but still fails.

  Disable bluetooth, no effect.

  Diagnostic HP online support a wireless card problem, sent a replacement wireless card.

  Not installed, no improvement. Same behavior.

  Two dv6 wireless cards will connect two routers if G 802 eneables. Blutooth also works.

  All hp and windows updates installed (before all this and checked again after the new card installed).

  System always runs from as main player c. HP 750 g drive msata ssd drive as 2nd.

  (but probably not relevant,?)

  System for 2 weeks, just the windows 8 and a couple of installed items.

  Wireless-N has never worked, it not connected Wireless-g. G always work N never works.

  It works for EVERYONE on the Envy DV6-7000 series with windows 8?

  Windows 8 makes * beep * almost impossible to see how an adapter connects.

  You must go to the file Explorer, network properties, click the wi - fi connection,

  and look at the speed of connection. If its 54 Mbps, its G connection protocol.

  You can also configure the router on one N, see if it can connect to all.

  I just two bad wireless cards in a row, or am I missing something?

  Provided with the wi - fi - model Ralink RT3290 card?

  Thank you for posting if you are sure that you can connect dv6 win8 wireless-N, I would like to know

  If it still works.

  Thanks for your time.

  First of all, thank you for the Nice fellow who took the time to answer.

  After several hours with HP support, we have reloaded windows as a last resort.

  This fixed the problem of wireless-N with the ralink wireless card.

  I have created the restore point, applied updates (windows update) via the hp support assistant.

  Eventially has all the recommended updates and ended with several update option.

  Make a restore point

  Load the update of Microsoft as an option for ralink (975 k no id #), he again DEFEATED Wireless-n.

  Thank you MesS!

  Once loaded, it shows in the history of the update, but has no way to uninstall it.

  Also, no way to uninstall from the Programs window.

  Fortunately, I had a restore point.

  ===

  MS Forum:

  Try this driver from hp support.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4132&swLang=13&mode=2&taskId=135&swItem=ob-113862-1
  I have the same problem after recent Windows Update the Ralink driver. The drivers of hp seems to work very well.

  If you're stuck with this issue and do not want to wipe your drive and reload windows,

  You can try the above driver or the driver suggested in the other response.

  I don't know how to remove the fake ralink against MS update.

• In app purchase does not even with the correct password, keeps telling me to contact support Apple, anyone else?

  CCan can't purchase of gems in the app, I get the correct password, and then it requires I answer the security questions, then he said I need to contact Apple support, even though security questions correctly answered like a password! That is what it is? TO

  Click here and ask for help from the staff of the iTunes Store. Only, they know.

  (140077)

• Unable to connect to a network printer with Win7 x 64 machine

  I have a printer that is shared on a Server 2003 server is installed. I can find the printer when I add a printer, but at the end of the installation it says "Windows cannot connect to the printer. I am trying to install this printer on a Win 7 Pro x 64.

  I installed this printer on a Windows 7 Pro 32 x machine.
  I have the same printer brand a "HP Laserjet P2050 Series PCL6' installed on my W7x64 machine but from another server (Server 2003 yet).
  If the driver is already installed on W7x64.
  Also, I was able to install it using the IP address, but our software companies used the \\Server\printer convention for their print programs. so, it should be installed like this to work with our enterprise systems.
  It's very frustrating.

  Hello

  The problem you are having is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the TechNet.

  Please post your question in the Technet Forum.

  You can follow this link to ask your question:

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

  For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• Unable to connect to a network printer

  I am unable to connect to my network printer, even if when I run the command 'Connect to the printer' and select 'network', while the program is able to see my network printer, it crashes when I select the printer.

  I was able to connect to the printer in the past, but for some reason any printing interrupted.  I deleted and reinstalled the printer (HP OfficeJet Pro 8600) with the CD that came with the printer and once again, while trying to connect it froze.

  Any suggestions would be greatly appreciated.

  Hi André,.

  Welcome to Microsoft Community where you can find all the answers related to Windows.

  According to the description provided, looks like you can not connect to the network printer.

  I have a couple of steps, which I think should help you with this problem.

  Method 1:

  Try the steps mentioned in this link and check:

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Method 2:

  Visit this link to learn more about "Troubleshoot network printer."

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  In addition, visit these links and check:

  What are printer permissions?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-printer-permissions

  Troubleshoot file and printer sharing

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-file-and-printer-sharing

  Hope this information helps. In case you have issues with Windows, post here to Microsoft Community.

• Unable to connect to this network

  I have a samsung series 7 chronos 2013 np780z5e the intel centrino n advanced wireless installed, running 64-bit windows 8 6235 card. I can connect to my home network with wpa2-personal encryption and the public WiFi at my University. However, I can not connect to wpa2-enterprise security connection. It finds the network credentials and then immediately provides the message 'Unable to connect to this network', without asking for credentials. This network works fine with other laptops, and I can even connect with my phone. I think it's a matter of windows 8.

  I tried the automatic network troubleshooting and updating to the latest drivers, but neither have worked.
  Update: after network oversight, update drivers and reboot, it works now. Either reboot or forget the add new network and fixed the problem

  Hello

  The majority of connection to Windows 8 breast problems have been resolved by installing the latest driver for the wireless card with obtained from the manufacturer.

  Thanks for sharing the information. In case, if you need help, you can always after your questions related to Windows and your valuable suggestions in the Windows forum.

• Unable to connect to wireless networking

  My Toshiba laptop has been pre-installed with Windows 7 Home premium 64 - bit OS and it worked quite well with the BB wireless. However, the wireless internet was on and turned off in recent weeks, while other mobile devices, such as iphone, ipad, or laptop, in my household had no such problem. The wireless signal was so strong, but the error message always says "unable to connect to wireless networking. It seemed that there was something wrong with the wireless adapter.

  I got a new adapter properly installed TP-Link wireless. Fortunately, it worked; but unfortunately, it worked for less than 24 hours. It was really frustrating that I, like student full time, depended so much on the wireless network card.

  Help, please! Harry

  Hello

  You can enlighten us with:

  -What model do you use (eg..) L300-123)
  -What version of BIOS is installed?
  -WLAN driver do you use?

  All these questions are answered in PC Diagnostics are under Toshiba app folder in the start menu.

  BR

  Tom

• I can connect to my network, but with access "local only".

  Access to the "Local" network only
  I can connect to my network, but with access "local only".  Internet became more intermittent (not sure if that is related or if I guess it) and did not work in several weeks.  Desktop computer is plugged into the router, but have the same problem when it is plugged into the DSL modem.  Other computers on the same router (wireless or other) work very well.  Recently, I removed Mcaffee and installed MS security essentials.  I uninstalled mcaffee of programs and settings then used the mcaffee removal tool to lighten the rest.  I uninstalled and reinstalled MS security essentials.  I thought it might be a firewall issue, but I get error 0x6D9 when I try to start it.  I tried all the steps in the following post, nothing helps.  Any other suggestions?

  ______________________

  You can follow the steps below and check if that helps you solve the problem.

  Method 1

  Try to power cycle the router and the computer and check if it helps.

  On the PC:

  1. Save your work and restart the machine.

  On the router or modem (if wireless printing):

  1. Unplug the router and the modem.
  2. Wait 30 seconds.
  3. Plug in the modem and wait for it to come to the ready state.
  4. Plug in the router.

  After you put cycle check the connection between the router and the computer.

  Method 2

  If the steps above do not help, you mayreset TCP/IP stack. To reset access the link below and either click on "Fix it for me" or follow the instructions to fix it yourself:http://support.microsoft.com/kb/299357
   
  Disable the IP helpdesk:
  1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter
  2. scroll down to the IP assistance service, right-click on it and select Properties
  3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.
  4. then click on "Stop" to stop the service from running in the current session
  5. click on OK to exit the dialog box

  Method 3

  Disable IPv6 and remove IPv6 virtual cards:
   
  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.
  NOTE: You should do this for each network connection, even if they are disabled.

  Method 4

  Disable the DHCP Broadcast Flag:
  Link: http://support.microsoft.com/default.aspx/kb/928233
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://support.microsoft.com/kb/322756.  How to back up and restore the registry in Windows
   
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
   
  To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:

  
  1. Click Start, type regedit in the search box, and then click regedit in the list programs.
  2. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  3. Locate and then click the following registry subkey:
  4 HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}
  5. in this registry path, click the (GUID) subkey that corresponds to the network adapter that is connected to the network.
  6. on the Edit menu, point to new, and then click DWORD (32-bit) value.
  7. in the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.
  8. right click on DhcpConnEnableBcastFlagToggle, then click on modify.
  9. in the value data box, type 1 and then click OK.
  10. close the registry editor.
   
  By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.
  You can also try uninstalling and reinstalling the driver for the wireless card.

  ________________

  Thanks for any help!

  Hello

  All changes to the software or hardware of the computer?

  Method 1:

  Visit the link below and follow the steps.

  Of network connectivity status incorrectly as 'Local' only on a Windows Server 2008 or Windows Vista-based computer that has multiple network cards

  http://support.Microsoft.com/kb/947041

  Method 2:

  Update the NIC drivers and check.

  Network adapter problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

• on startup, I get the message, unable to connect to all network drives

  at startup I get message (unable to connect to all network drives) I use windows 7, intel i3, 64-bit and ie9.

  Hello

  Were there any changes (hardware or software) to the computer before the show?

  Method 1: Perform the steps from the link below and see if it helps.

  Programs may be unable to access some network locations after you turn on user account control in Windows Vista or in Windows 7

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  Method 2: Click on the link below and see if it solves the problem.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Networking/cannot-reconnect-all-network-drives/5c5a4492-1634-4479-91f9-b4d2763b31d2

  Hope this information helps.

• Unable to connect when I try to sign, he said: "your computer is offline. Please sign in with the last password used on this computer. »

  Original title: Unable to connect

  Ok. So I'm having a few problems to connect to my computer windows laptop 8. I have reset my password like 5 times, restarted my computer over the same period of time, and I can not even sign. When I try to sign, it says: "your computer is offline. Please sign in with the last password used on this computer. "Well, I don't know what was the last password. I'm sure that the last time I registered on my laptop, I used the PIN that I used to have for her. The only reason why I changed it was because I wanted it to be more difficult to get into my PC. But I wanted more difficult for other people, not more difficult for me. Can someone help me with this please?

  Hi Arianna,.

  Thanks for posting your query on the Microsoft Community.

  I understand the inconvenience caused to you. I'll be happy to help you with your problem.

  I suggest you refer to the suggestion given in the thread and check out them below if it can help solve your problem:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-security/whats-the-fix-for-your-PC-is-offline-please-sign/fd7dc731-6e23-4044-BFEE-dd8fbb42fc32

  Let us know the status of the issue. We will be happy to help you further.

  Thank you.

• Unable to connect even after the user password reset

  Hai all,
  
  10.2.0.3 on Linux
  
  Reset a user password and the user is unable to connect as you can see below
  
  
  [oracle@testdb 10.2.0] $ sqlplus sys/Manager as sysdba
  
  SQL * more: release 10.2.0.3.0 - Production on Tue Nov 27 16:20:21 2012
  
  Copyright (c) 1982, 2006, Oracle. All rights reserved.
  
  
  Connected to:
  Oracle Database 10 g Enterprise Edition release 10.2.0.3.0 - Production
  With partitioning, OLAP and Data Mining options
  
  SQL > alter user sysman identified by oracle.
  
  Modified user.
  
  SQL > disconnected from Oracle Database 10 g Enterprise Edition release 10.2.0.3.0 - Production
  With partitioning, OLAP and Data Mining options
  
  [oracle@testdb 10.2.0] $ sqlplus sysman/oracle
  
  SQL * more: release 10.2.0.3.0 - Production on Tue Nov 27 16:20:32 2012
  
  Copyright (c) 1982, 2006, Oracle. All rights reserved.
  
  ERROR:
  ORA-01017: name of user and password invalid. connection refused
  
  
  
  Unable to connect even after the user password reset

  Check
  How to change the password of the database user Sysman (DB control repository schema) [ID 259379.1]
  EMCA 11 g fails with the error "ORA-01017: name of user and password invalid; connection refused"and" username/password invalid name; For DBSNMP or user SYSMAN"[ID 741530.1]

• At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  original title: server and virus problem

  Hi SurajMendon,

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the platform of networking on TechNet. Please post your question in the TechNet Windows XP Networking forum.

  Networking platform

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads