Unable to connect wireless after the upgrade to Windows 7 since Vista.

Similar Questions

• HP Photosmart C6280: cannot print on C6280 wireless after the upgrade to Windows 10

  Cannot print on C6280 wireless after the upgrade to Windows 10. Have removed the device, but try to re install the printer when is not found. Can print if I connect USB. Tried to reload the driver using HP Support software help, but when he arrives at the end of the download fails.

  Hi @Ron9871,

  Welcome to the Forums of HP Support!

  I see that you are unable to get your printer HP Photosmart C6280 wireless printing. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to try the steps in this guide, "offline" Status Message printer (Windows 10).

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  • Print a Page of Network Configuration menu of the printer front panel. Note: the IPV4 IP.
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.

  Please restart the router, the printer and the computer in this sequence.

  If you're still having problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  • Use the File Checker system to repair missing or corrupted system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  You can try to change your WSD printer port by a Standard TCP/IP port.

  To do this, you will need your current IP address printers.  The Network Setup page shows the parameters of network for the product. To print this page; Press the button of network () on the control panel of the product.

   

• Cannot connect to internet after a reboot before you uninstall and then reinstall the network card. (After the upgrade to Windows 7 from Vista)

  This problem started immediately after the upgrade to Windows 7 Ultimate (32 bit) to Windows Vista Ultimate (32 bit).  Again, I want to remind that I never had this problem before installing Windows 7.

  -After a reboot, I am presented with the impossible to connect the network indicator (yellow triangle with!) in the task bar.  (It was how I was welcomed after the installation of Windows 7 is said by the way).

  -The only way I found to regain connectivity is to uninstall and reinstall the network via the device manager card, date at which the computer always successfully connects and remains connected until the next reboot.

  Network card: Realtek RTL8168C (P) / 811C (P) Family PCI - E Gigabit Ethernet NIC (NDIS 6.20)

  Driver provider: Microsoft
  Driver date: 14/05/2009
  Driver version: 7.2.1127.2008
  Digital signer: Microsoft Windows

  Thus, we have solved the problem! There are two possibilities of your problems:
  1 company Adobe uses the Bonjour service , this service should be disabled.
  Computer > Manage > Services and Applications > Services => find the bonjour service (sometimes stated as long numbers), stop service and if the Disabled value. It works!

  2. If it is not signed as Bonjour service. Try to disable the service:
  Shutdown mDNSResponder .exe (he is represented by # Id_String1.6844F930_1628_4223_B5CC_5BB94B879762 #).

  It is installed with Adobe software. If you upgrade the Vista, it will generally many users problem!

• After the upgrade to Windows 7 from Vista, I lost the previously loaded Fund games

  I recently downloaded Window7 on my PC.  Download Afthe was complete, I played games that were on my desk from the previous OS (Vista).  I have the next day got up and played them again and took off.  Upon my return, all games had disappeared from my office and cannot be found.  The only ones left are a compilation of classic board games from Microsoft.  The games I lost were; Free Cell, hearts, Solitare, Spider Solitaire, Minesweeper, and failures.  The question is: "How do they return?

  Original title: recovery lsot games

  Hi Richard,

  Thanks for the post. I understand that you have lost the default Windows 7 games like Solitaire, Minesweeper and etc. All changes made to the computer before the show?

  The games you mentioned are by default Windows 7 games and these are features of Windows 7. You will need to access the Windows features and then turn them on. Check out the link and follow the steps.

  Where are my games?

  http://Windows.Microsoft.com/en-us/Windows7/where-are-my-games

  I hope this helps to solve the problem.

• I lost my msn icon after the upgrade to windows 7. How I connect msn plsu? What is the web address?

  I lost my msn icon after the upgrade to windows 7. How I connect msn plsu? What is the web address?

  Hello

  I suggest you to contact MSN customer support for assistance.

  Here is the link for "how to contact MSN Support.

  http://support.Microsoft.com/kb/940784

  I hope that helps!

• Unable to connect even after the user password reset

  Hai all,
  
  10.2.0.3 on Linux
  
  Reset a user password and the user is unable to connect as you can see below
  
  
  [oracle@testdb 10.2.0] $ sqlplus sys/Manager as sysdba
  
  SQL * more: release 10.2.0.3.0 - Production on Tue Nov 27 16:20:21 2012
  
  Copyright (c) 1982, 2006, Oracle. All rights reserved.
  
  
  Connected to:
  Oracle Database 10 g Enterprise Edition release 10.2.0.3.0 - Production
  With partitioning, OLAP and Data Mining options
  
  SQL > alter user sysman identified by oracle.
  
  Modified user.
  
  SQL > disconnected from Oracle Database 10 g Enterprise Edition release 10.2.0.3.0 - Production
  With partitioning, OLAP and Data Mining options
  
  [oracle@testdb 10.2.0] $ sqlplus sysman/oracle
  
  SQL * more: release 10.2.0.3.0 - Production on Tue Nov 27 16:20:32 2012
  
  Copyright (c) 1982, 2006, Oracle. All rights reserved.
  
  ERROR:
  ORA-01017: name of user and password invalid. connection refused
  
  
  
  Unable to connect even after the user password reset

  Check
  How to change the password of the database user Sysman (DB control repository schema) [ID 259379.1]
  EMCA 11 g fails with the error "ORA-01017: name of user and password invalid; connection refused"and" username/password invalid name; For DBSNMP or user SYSMAN"[ID 741530.1]

• Laptop Compaq CQ58: LAN Ethernet does not work after the upgrade to windows 8.1

  After the upgrade of Windows 8 to 8.1, my Ethernet LAN is no longer in effect. Wireless LAN connectivity is OK. I run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I don't see a listed 8.1 for the LAN Ethernet driver.

  It seems that you encounter the same problem, I did when I ran the free preview of the W10. I had this error on the card reader.  I have no idea how to solve this problem.

  Is there is no ethernet controller needing drivers in Device Manager, then it is probably the realtek lan adapter that has the number 12 of the code, or it is part of the motherboard that controls the ethernet adapter.

  If you need Atheros bluetooth driver, then this is probably the one you need.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_127984_1

  Unfortunately, I won't be able to help you with question 12 code or ethernet.

  IMO, they are insoluble.

• Volume controls on the keyboard after the upgrade to Windows 8

  I have a Touchsmart 520-1070 with the mouse and keyboard without wire factory.  After the upgrade to WIndows 8, the volume controls no longer work.  I tried the Recovery Manager to reinstall the keyboard drivers, but there is no driver keyboard under hardware drivers.

  In the following device manager are listed under keyboards:

  HID keyboard device

  Keyboard 109 MCIR Microsoft eHome

  Keyboard MCIR Microsoft eHome

  Microsoft eHome key remove control Keayboard

  PS/2 standard keyboard

  Any report that they are installed and are working correctly and that the drivers are up to date.

  Has anyone else seen or solved this problem with a Touchsmart computer?

  The instructions below were provided by HP support.  This has restored the function on the keyboard volume controls.  The referenced below drivers are drivers IDT high definition Audio Device.  I am not sure that it was necessary to reinstall the audio drivers.  It can only had to remove the USB dongle and back to restore the functionality of the button.  Note: the USB dongle is located behind the VESA Panel to the back of the PC.  No tools are required and the dongle can be removed and replaced without shutting down the PC.  VESA panel removal requires a bit of a steady hand, pulling the lip which is close to the connections on the rear panel.

  Instructions received from HP:

  Please go to the following link and check the "return of the system", article #7 is the USB dongle:

  http://support.HP.com/us-en/document/c03026390

  After you have reinstalled the receiver, please download and install the following driver:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-110499-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

  Then install the following update:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-112060-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

• After the upgrade of Windows Windows 7 10, could not recover my product key.

  Original title: windows 7

  After the upgrade to windows 10 windows 7, could not recover my product key. When I connect my system am get notification that you may be victim of software counterfeiting and copy of windows is not genuine. you do me too much this error code. 0xC004F057. Please help me to recover my product key. my windows does not work after the upgrade as well.

  I suggest that you run the diagnostic tool Microsoft Genuine Advantage in normal mode and copy and paste the results into a response for further analysis:

  http://go.Microsoft.com/fwlink/?LinkId=52012

  Run the tool and when it ends, click the copy button, open a text such as Word or Notepad file and select Edit, paste. You can paste directly into an answer here. Open a response, right click and select Paste.

• Lightroom does not start after the upgrade to Windows 10, Version 1511, 10586

  Hi all

  After the upgrade to Windows 10, 1511 Version, lightroom 10586 CC can't be launched. Adobe cloud nor any link office or file system path to the files directly program. Lightroom.exe can be seen in the Task Manager for a second and then disappears to nirvana. No answer, no trace.

  What should do?

  standard things as uninstall - re - install, stop between the two, log out of the clouds - connect to the cloud, register of audit were made in several variants without success!

  Kind regards

  Robert

  Thank you hipolitorodrigues,

  your answer showed me the way. I found a solution more simple in a parallel thread, whose response brought back LR to life.

  CU, Robert

  8  re: does not start Lightroom CC

    

     Tanuj Sandal   14.12.2015 19:41 (als Antwort auf: antonk97314826)

  Go to the Panel, then programs and features.

  Please select Microsoft Visual C++ 2012, 2013, and fix it.

  Restart the computer and then let me know if the application works.

• FN keys do not work after the upgrade to Windows 10

  Why the FN keyboard does not work after upgrade to Windows 10?

  FN keys are controlled by utilities and special tools of Toshiba. Usually after the upgrade to Windows 10, the parts of the pre-installed Toshiba software must be upgraded to version compatible and support Windows 10...

  You have not provided information on the laptop model so I can't say with certainty if your unit is 10 Windows supported or not...

• Satellite P855 - function keys do not work after the upgrade to Windows 10

  Function keys do not work after the upgrade to Windows 10
  I know that I need two drivers (Flash cards support utility) and (Toshiba function Key Utility), but on the page download Toshiba is not suitable for Windows 10.
  Anyone know when and if it will be available?
  Thank you

  I'm also waiting for Win10 of things and do not know with certainty how Toshiba will start with the support of Win10. I hope that will happen soon.

• Problem with a keyboard key of T440 after the upgrade to Windows 10

  Hello world

  I have a Brazilian keyboard layout (ABNT2) on my T440 and I am facing a problem after the upgrade to Windows 10. The new version of Windows recognizes this key:

  

  As long as the "CTRL on the right" (commom on other layouts).

  Everyone was faced with a similar problem or have any clues as to what might solve this problem?

  Thanks in advance,

  Felipe

  Solved.

  Do more research, I fount out is an old bug with Lenovo's Thinkpad laptops with this Brazilian keyboard.

  If you are facing the same problem, use this registry tweak and the problem is solved:

  http://ZTop.com.br/WP-content/uploads/2009/11/thinkpad_abnt_win7.zip

  (the file name indicates "win7" but it also works for Windows 10)

• Re: Satellite A500 - FN key does not work after the upgrade to Windows 7

  Hello
  The FN key does not work even if I have (Toshiba Value added Package) and (toshiba flash Cards help).
  Happened after the upgrade to Windows 7 and using the upgrade CD to retrieve all of the tools and utilities.

  Satellite A500 - 134

  Try restarting Flash cards.
  Start > all programs > Toshiba > utilities > restart Flash cards.
  After doing this press FN button several times.

• After the upgrade to windows 7, Warcraft3, Battlefield Viet Nam cannot run in 4:3 screen but 16:9

  After the upgrade to windows 7, Warcraft3, Battlefield Viet Nam cannot run in 4:3 screen but 16:9... my East of 1366 X 768, so the games are run with black screen on the left and right sides... What can I do? He has run well in Vista =]

  1366 x 768 is the strangest resolution that I've ever heard of. Your video card drivers helped "keep the proportions" and decided to not to stretch imagine because I assume that you can't choose this exact resolution in the game. If your monitor has an overdrive video or image format option, you can enable or disable that or if you have a NVidia card, you can change the picture format option in the properties of the video card.

  If you have an ATI card, then you're stuck with a proportional image: P