Unable to fax due to voicemail, answering the line

Similar Questions

• HP C7240 message "Unable to scan, copy or fax" appears when I lift the cover on dish

  This happened for some time. Whenever I raise the lid, this message appears: "unable to scan, copy or send a fax. If I type "OK" everything returns to normal. I am able to fax and scanning from the doc feeder, but some things are just too thick to put thru. I tried to put my paper under the lid while the appliance has been turned off, so I was not raised the lid, perhaps thinking he might still scan from the dumpster, but no. I get the same message as soon as I turn on the printer. Running Windows 7.

  In addition, there is a line on my paper when I scan through the doc feeder. No idea how to get clean or repair everything that makes the line?

  Thank you!

  Yes, life has a way of doing that sometimes.  I'm you a link to a document of troubleshooting for lines in copies of the automatic feeder (ADF) documents.  Click here  A thorough cleaning of the ADF will probably solve this problem.

  The error message "Unable to copy, scan or fax" may be more difficult to overcome.  On the only step left that could be considered would be a semi full reset.  This reset the default printer and clear the memory.  If the printer was on a wireless network, it should be removed and would need to be reconnected.  If you want to try this, I can send you the steps in a private message.  I need you agree to not post the stages.  Let me know what you decide.

• Unable to answer the call of the CSQ

  Hello

  We have intermittent problems with some agents are unable to respond to a call for a CSQ. This seems to only happen when the call is transferred to one QSC to another.

  Scenario of
  The call comes on CSQ1 and Agent1 answers the call.
  Agent1 forwards the call to CSQ2.
  In CSQ2, Agent2 can see their status is set to 'Reserved' at the office of the Agent, but the appeal does not ring on their phone. The call is still active on the phone to Agent1.
  Agent1 can try to transfer again, but the same problem occurs. The call seems to be stuck on the phone to Agent1.

  The question is not subject to an Agent or a CSQ, happened on multiple Agents in multiples of the CSQ. The agent is not a resource in both in these situations of CSQ.

  We are running:
  UNIVERSITY COMPLUTENSE OF MADRID: 9.1.1.20000 - 5
  UCCX: 9.0.2.10000 - 71
  Devices: IP Phone 7945, SCCP Protocol

  Any thoughts or ideas are greatly appreciated.

  Thank you.

  You should try the region of the contact for this issue Center

• I have CS5 on Windows desktop 8.1 which I'm unable to update due to the repeated download error (no error number). I uninstalled and reinstalled CS5 but the same error occurs. I have same CS5 on Windows 7 laptop which seems to be up-to-date. What's wrong

  Issue. I have CS5 on Windows desktop 8.1 which I'm unable to update due to the repeated download error (no error number). I uninstalled and reinstalled CS5 but the same error occurs. I have same CS5 on Windows 7 laptop which seems to be up-to-date. What is the problem please?

  Hi Peter,.

  Please see the updates

  Hope that helps!

  Kind regards

  Sheena

• HP Officejet 8610: Unable to fax from the computer

  I have a HP Multifunction printer and use the fax from the computer option several times a month. I discovered this week that she did not work AGAIN. I have had this printer about a year and need to reinstall the software several times. When I select the fax printer and say 'print', the fax screen should display and ask where to send them, but nothing happens. When I check the devices screen and printers, it shows the fax as unrelated to printing or pending tasks. The machine is connected because I can print to this well, that's just something wrong with the communication by fax. I found that uninstalling and then reinstalling the printer solves the problem, but the number of times that I needed to do this is frustrating. I guess that something is messed up when windows does its updates. Is there a setting of simple connection that I could update instead of reinstalling everything on all of the computers on my network? Maybe HP could be added a correction for this option to their troubleshooting.

  Hello

  You can use the universal Fax HP driver instead:

  1. Download and extract the following:
     http://FTP.HP.com/pub/softlib/software13/COL60874/DS-146586-1/HPUFDDriver.zip
     (Use a program like Winzip or right-click on the file and select extract all).
  2. Open the extracted folder and run setup.exe
  3. Follow the instructions on the screen, a printer HP Universal Fax Driver will be created on your PC.
  4. HP Universal print driver Fax, select your printer and check the box to add a queue for your printer.

  Kind regards

  Shlomi

• All in one C7280 printer has become unable to fax after switching to ATT Uverse

  Printer all in one C7280 has become unable to fax after changing to ATT U-verse Internet wireless router. Internet and e-mail works well without any change.

  Can you help me what I need to do?

  KAZ

  KazUtsumi, I recommend first meeting AT & T and check to see if they provide a digital filter for your configuration and make sure that everything is in the right order (generally the fax must be one of the first things that connected to the telephone line).

  With regard to the installation, what else do you have on this line (telephone, answering machine, credit card machine, etc.) or is it a dedicated fax line?

  Let me know!

• No favorites, recents, contacts, keypad, voicemail at the bottom of the screen

  typing on the phone on the main screen icon does not display the list of contacts, but it not there no icons for the voicemail at the bottom of the screen, contacts, Favorites, keyboard, recent. Help?

  Just answered my own question... Power the phone off and reboot brought back the icons on the screen of the phone. Go figure.

• you forgot to answer the secret questions on APP Store too, I lost your e-mail account in order to find the answers

  I forgot to answer the secret questions on APP Store also, I lost my email account in order to find the answers

  You have to ask Apple to reset your security questions. To do this, click here and choose a method; If this page does not list one for your country or if you are unable to call, complete and submit this form.

  (136721)

• MSG for error in Windows 7: "unable to load DLL 'Gpib - 32.dll': the specified module could not be found."

  Hi people, I have a project in VB. NET (VS2010 specifically), which has been updated from an old VB6 project. The old project

  use Niglobal.bas and Vbib - 32.bas to communicate with the GPIB plugged into one of our litters.
  Now in the 64-bit Win7 with the Niglobal.bas and the Vbib - 32.bas converted to Niglobal.vb and Vbib - 32.vb,.

  I get an error when debugging to

  Public void RegisterGPIBGlobals()

  in the Vbib - 32.vb, the error msg says:

  Unable to load DLL 'Gpib - 32.dll': the specified module could not be found. (Exception from HRESULT: 0x8007007E)

  It seems like this Gpib - 32.dll, that I found under SysWOW64 on my Win7 is not designed for a 64-bit application and when I copy this dll file on

  C:\Windows\System32, the msg of error becomes:

  An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)

  So I think my question is double: 1. the drafting of my own app in VB. NET can I still use Gpib - 32.dll (including the Niglobal.vb and Vbib - 32.vb)?

  2 Will the application I am writing with .NET work in x 64 Windows 7?

  The Almighty gurus and Mods please help. Thank you!

  Hi Joel, thanks for the answer! I have the 3.0.2 driver.

  I was looking around for a while after I posted here and further in the use of NI4882 manual, page 4-4, I found this:

  «To bring an application in an environment 64-bit requires the application to migrate the NI4882 API and be recompiled.»

  So I'm ditching the gpib - 32.dll (vbib - 32 & niglobal) and currently I am using NI4882.dll and restructuring of my project.

• Understand fax failure oregano and corrects the prejudices of the solution or alternatives

  I have problems sending a fax failed after that analyses a number of revenue and then transfer them into a MS Word Document in a Word format. I have some basic questions based on fax trying to figure why faxes fail and how to prevent them from doing.

  Using Microsoft word 2007, running Windows 7 on my model # KN904UA #ABA HP Pavilion dv9700 notebook PC computer phone fax on a color HP LaserJet Pro CM1415 MPF series all in one printer. I tried faxing multiple documents several times to see that it gets to the next to the last page and fails. These documents are 15, 18, 19, and some even 21 pages long. And I wonder if one of the following solutions would work, tell me what you think? 1. cut the faxes in the half and passing the final part of the fax only, 2. By saving the document faxes in PDF and fax to PDF MS Word verses. 3. selection of the target destination Fax either from the AddressBook menu Fax (before frequently used saved fax number), or the fax number entering manually every time when sending a fax.

  Can someone help me answer a few basic questions base of fax or understand why they fail? :

  If I save a document in Word, click on print, choose to fax in the print options, the fax saves the file in the memory of the coil first before, it fires the fax process to start fax? In the affirmative when the file is saved in the coil of the memory, can I turn off my laptop and then the fax will continue Fax fax fax memory of coil? The fax data transfer rate is equal to a 14/4 Baud rate modem?

  I can't fax anything longer than 10 pages. A 21 page document must be divided into 3 segments: name 1 file name page, page 2, and page 3 of the file file name.  I hope this helps others with the same problem and inquierrie. Chris

• Fax machine, do not leave the machine to pick up.

  Have a 7520 HP printer all in one. I have a phone/answering machine plugged into the rear 2EXT port and the other phone cord supplied with the printer in the other and it goes on the phone jack in the wall.

  I have problems with the fax machine pick up anything. I got the answering machine pick up on the 2 rings and the 3rings for Telec pick-up setting.  The fax keeps howling through once the answering machine picks up.

  Any ideas?

  Hello

  Please change the no. of the rings on 4 printer and check.

• Necessary to reach the line of Fax Long Distance access code

  I have a HP all-in-one Officejet J4550 Copier-scanner-fax.  My question is how can I send a fax when I need to enter a series of numbers without connection with the fax number to reach a long-distance line?  It's a long story, but I mainly long distance access via a calling card.  I first call a toll-free number and enter a 12-digit before I can enter the fax number.  The Officejet does not seem to have provisions for this.  She has just one field for the fax number.

  I was able to answer my own question by using the method of trial and error.  It turns out that you can use the machine all-in-one HP Officejet J4550 fax 'manual', after all.  Forget the software "Solution Center".  I wrote just to the top of the other fax manually on the phone machine, put in all my codes required.  When I got another fax to the line, I put the Officejet key 'FAX (black and white)' using the arrow (adjacent to the 'OK' button '), responsible for my fax in the feeder and you press '1' at the prompt to send the fax.  (By pressing '2' will tell the Officejet to receive a fax.)  It's good to know, especially for the time that you can not by software.

• Problem of the printer, I get "the computer is unable to establish two-way communication with the device.

  Original title: printer problem

  "The computer is unable to establish two-way communication with the device. I have pluged a all cables and pluged in that they return.

  Hello
   
  1. What is the brand of your printer?
  2. when the question is is produced?
  3. you remember to make changes to your computer before the problem?
  4. when exactly you get this error?
   
  I would temporarily disable all security software and check if the problem persists.
   
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
   
  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
   
  If you have an HP printer, you can consult the links below.
   
  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=&cc=us&DocName=c01868684&product=3737195
   
  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=&cc=us&DocName=c00301806&product=407677
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Windows Fax and Scan-do can't fax any type of attachment "the message could not be sent. These data are incorrect. »

  Original title: Windows Fax and Scan is unable to fax any type of attachment

  I am trying to send a PDF using Windows Fax and Scan Ver 6 Build 6002 SP2.
  I get "the message could not be sent.  These data are incorrect. »
  I can send a cover sheet, or something typed into the dialog box, so the modem works fine.
  The problem is with an attachment to a fax.  Tried to PDF, DOC, ZIP, JPEG, and TIFF.
  I found lots of posts with the same problem, but no solutions or problem.

  Windows Vista Business SP2, Adobe Acrobat 9 Pro using

  Just ran the SFC system (C:\windows\systems32\sfc/scannow) and repair files corrrupt.  WF & S now works well when you attach files.

• I'm unable to download games, programs, etc from the internet.

  I'm unable to download games, programs, etc from the internet.  It started a year ago and I still have the problem.  I click on "Download", the dialog box appears, click "run" dialog box appears indicating the time to download, and then click "Run" and the dialog box disappears without ever finishing.  Anyone know what is happening, why and how resolve it.  Please keep in mind I'm not savvy with the computer language and need answers in the form of simple.  Thank you

  There is no way to accurately diagnose that lasts a year and with so little information. You should start by ensuring that the computer is free of viruses/malware:

  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  Post back with the results for further assistance.

  If you can't do the work yourself (and there is no shame in admitting this isn't your cup of tea), take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad). If possible, have all your data backed up before taking the machine into a shop.

  MS - MVP - Elephant Boy computers - don't panic!