Unable to get the restore point to work under vista. used to work ok.

commissioning went haywire and can take 30 minutes and have to use the escape key to bring up the achievable screen. Help.

Hi Winston,

Thank you for your advice. Apart from the problam of restore point, there was also a major problam start but I entered the configoration system and activated on start up and this has solved. I'll try again restore then outside the mode without failure, then in the case where the start was part of the problam point and go from there. I will let you know the results. Thank you very much.

Mark

Tags: Windows

Similar Questions

  • Re: Unable to get the wireless adapter to work on my Satellite L550-1CC

    I'm getting bored with this laptop, I reinstalled windows 7 (32 bit) and can not get the wireless adapter to work.

    My router settings are perfect, my netbook is zero connection problems - the router is just inches away from the laptop most of the time - the laptop insists that there is "no available networks."

    This of course is BS, before I reinstalled windows I could pick up 3 other neighbouring networks as well as mine.

    Windows automatically installed the wireless network - I thought that could be the problem, so I downloaded the realtek driver directly.

    No difference. Always the small icon with Red Cross barred through it.

    I thought it could have been a hot key problem - so I installed the flash card driver that apparently controls the access keys (for some reason any).

    Shortcut keys still don't work - I could really care about that - it's just the wireless network I need.

    Thanks for any help I receive.

    > my netbook has zero connection problems - the router is just inches away from the laptop most of the time - yet the laptop insists there is "no available networks."
    After reading this sentence, I'm a bit confused. If there is no available WLAN networks how your laptop had zero problems to connect?

    One last thing:
    > Of course is BS, before I reinstalled windows I could pick up 3 other neighbouring networks as well as mine.
    What is the difference between the old and the new installation of Windows?

    In general the WLAN use is fairly simple.
    Wireless network card - must be installed correctly (listed in Device Manager
    WLAN card - must be enabled using FN + F8 key combination to activate the wireless network card
    -scan the available WLAN networks area, click on the button of your WLAN and use connect
    -put key WLAN if necessary and after a few seconds WLAN connection will work

    I did this many times on laptops preinstalled Win7 and didn't have any problems. On all laptop computers pre-installed with Toshiba recovery image (factory settings) is not necessary to change the WLAN settings.

  • Unable to get the restore to work - Satellite 1410 disc

    I have a Toshiba Satellite 1410. During a restore of system with restore disks, I forgot to plug it. During the windows set up (this screen where you put in your country and all that) the battery has flat that I plug!

    I tried to throw the disc again, as it came with a box when I rebooted that said "the system is not fully restored. Please re-run Setup '. So I turned off and restart, then the message goes up after that windows image appears during startup.

    I bought this laptop second hand so I have all the manuals or books with him, I do not know the keys on which support to MSDOs not that I know what to do from here, I do not know which key press during boot up to get the CD to work, I have pressed the keys left right and Center and found exhaust takes me to a page of the system but anything to get the CD to run again that I thought would get just the restoration will once again.

    So now it starts up saying ' not completely restored system, please run the installation again.

    Someone know or seen this before, and someone can tell me if there is a simple answer, which key support during the start up or how to fix this?

    Thanks in advance.

    Hello

    As Daniel said in the first assignment by pressing the C button the laptop should boot from the disc. Please press that several times the C immediately after the laptop from.
    Then you can be sure that the option has been enabled.

    The other possibility is to enter the BIOS and then to change the initialization of the order on CD/DVD first

  • Unable to get the 'splash' screen to work with sample

    Using the RIM as a model example, I have this:

    {public Dib (boolean ribbonClicked)

    {if (ribbonClicked)}
    Launch the application
    this.pushScreen (new SplashScreen (UiApplication.getUiApplication (), new GameScreen()));
    this.pushScreen (new GameScreen());
    } else {}

    and this:

    public class SplashScreen extends full screen {}
    Private fields
    Following private FullScreen;
    application of UiApplication private;
    private Minu = new Timer();
      
    private final static Bitmap _bitmap is Bitmap.getBitmapResource ("berrysoft_logo.png");.
      
    Public SplashScreen (UiApplication ui, following fullscreen) {}
    Super(Field.USE_ALL_HEIGHT |) Field.FIELD_LEFT);
           
    This.application = ui;
    This.Next = next;

    This.Add (new BitmapField (_bitmap));
           
    SplashScreenListener listener = new SplashScreenListener (this);
    this.addKeyListener (listener);

    Timer.Schedule (new CountDown(), 5000);

    application.pushScreen (this);
    }

    but when I click on the application icon on the Ribbon, instead of work (as it does if I just press on GameScreen, it 'freezes' (a few seconds), then does nothing (IE never left the band).)

    What's wrong?

    The SplashScreen sample itself grows in the stack to display within its constructor.  You do not need to push, simply create an instance of it.  Pushing it, you try to push the same screen in the battery twice, which is not allowed.

  • Unable to get the content div to expand under the last tag div

    Again, I ask for help for my site www.acemon.com

    I can't get content to exceed the last div. When you look at the site, you can see the last box (titled "to the real estate agents") is surrounded by the color of .container instead of color content.

    You have an extra div to click here and clickhere2:

    Premium.html">."

    Click-images/sample.png"alt ="Value2"width ="150"height ="50"/ >

    value.html">."

    Click-images/realtor.png"alt ="Real Estate Agents"width ="152"height ="50"/ >

    Then, replace:

    with this at the bottom:

    that is to put the DIV outside comments.

    It must then validate.

  • Cannot open the synaptics pointing device in windows vista, upgrades are far but message error, unable to connect to the synaptics pointing device

    Hi I have a problem with my mouse/pointer when I click on the mouse to open it I have error message unable to connect to the synaptics pointing device. Have you checked the updates that are up-to-date, and the driver is ok, not sure what to try next need to make any changes to the mouse pointer

    with Brice thanks.

    Hi paiyay,

    Thanks for posting in the Microsoft Community.

    I understand that you are unable to open the synaptics pointing device in windows vista

    · You did changes to the computer before the show?

    · What happens when you click the Yes button in the error message?

    · You are able to use the mouse on the system?

    I suggest you uninstall the software from programs and features and then try to open the properties of the mouse and check if you are able to open the mouse properties then I would you recommend to uninstall the drivers that are installed on the system in the Device Manager and then download the drivers from the link below and check if the problem is resolved.

    http://www.Synaptics.com/support/drivers

    http://www.Synaptics.com/resources/drivers

    Updated a hardware driver that is not working properly

    http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

    Connect the hard disk, and then try running the fix tool of the article below and check out them.
    Hardware devices do not work or are not detected in Windows
    http://support.Microsoft.com/mats/hardware_device_problems/

    I suggest you to contact the mouse manufacturer for assistance. Click on the link below.

    http://www.Synaptics.com/

    See also:

    FAQ and troubleshooting

    http://www.Synaptics.com/resources/consumer-tips

  • Restore the system to a Restore Point fails: System Restore was unable to extract the original copy of the restore point consoleDirectory.

    I can create restore points and when updates are installed the system automatically creates a restore point. The problem is that I can't get the system to restore to a restore of these these points.

    System Restore was unable to extract the original copy of the restore point directory

    Source:%systemroot%\registration

    Destination: ComPlusStaging

    Hello John R H,

    Are you able to restore system successfully on a different date, or that you get the same result?  I looked through this thread and was curious to know why you want to perform a system restore?  Having other issues in addition to what you have described?

    Try to make a last good known Configuration and see if you are able to perform a system restore.

    Last good known Configuration:

    http://Windows.Microsoft.com/en-us/Windows7/using-last-known-good-configuration

    Please let us know status.

  • I uninstalled the touchsmart from hp on vista and then tried the system restore, dad will kill me, how can I get the touch screen to work again?

    I uninstalled the touchsmart from hp on vista and then tried the system restore, dad will kill me, how can I get the touch screen to work again?

    Hello

    You have a specific question for HP, it may be better if you ask in the Forums of HP's Support.

    http://h30434.www3.HP.com/

    See you soon.

  • Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."

    Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."  How can this be repaired?

    Hi rebick,.

    Try the troubleshooting steps presented by spirit X in this thread.

    Dena
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • I get error code 0 x 80070005 that reads "system restore failed during the restoration of the registry since the restore point.

    Original title: Windows 7 system restore always fail.

    I get error code 0 x 80070005 that reads "system restore failed during the restoration of the registry since the restore point.  I don't have Norton AntiVirus.

    If anyone can help solve me this problem I would be very grateful.

    Thank you for your response.  I forgot to mention in my first post, I tried both methods without success.  However, I finally understand how to solve the problem that led me to want to do a restore of the system in the first place. for now, I am therefore able to avoid a system restore.

    Thanks again.

  • Dates of the Restore Points are one month in advance

    For reasons I don't understand, the date of the day on my computer was changed to one month before the effective date, for example from May 13 to June 13, 2013. As a specialist, I kept getting messages that my Microsoft Security Essentials were outdated. Later, I discovered that all the restore points created after May 13 are dated June 13. I corrected the date and have updated Security Essentials and things are back to normal, but I have several restore points, a month in advance. Restore recent points are correctly dated now, but what can I do on these wrong, before the restore points. Thank you.

    If the pc works fine, then 2 options:

    1 turn off the system restore, which will remove all items, reboot, restart System Restore, and a system checkpoint will be created.

    2. go to disk cleanup, use the tab options, System Restore, cleanup, it will erase everything but the last system restore points.

  • Error snapshot VSS «file too small startup...» "during the restore point creating eventlog ID 12289 in Windows 8

    I am unable to do a restore point. There is plenty of space on both partitions.
    Config: A single drive with 2 partitions, one primary and one extended logical partition with Windows 8 on logic in dual boot with Windows 7 on the primary. The restore point creation in Win7 works OK but in Win8 it never worked alhthough all parameters seem to be OK.
    Device configuration:
    DISKPART > select disk 0
    Disk 0 is now the selected disk. NOTE: there is only 1 disc
    DISKPART > list disk
    Disc # status size free Dyn Gpt
    --------  -------------  -------  -------  ---  ---
    * Online drive 0 93 GB 1024 KB
    DISKPART > list volume
    Volume # Ltr Label Fs Type size status Info
    ----------  ---  -----------  -----  ----------  -------  ---------  --------
    Volume 0 DVD - ROM 0 B G no media
    Volume 1 - D drive of W7 NTFS Partition 54 GB healthy system
    Volume 2 C disc W8 NTFS Partition 39 GB Healthy Boot
    DISKPART > list partition
    Partition # type Offset size
    -------------  ----------------  -------  -------
    Partition 1 primary 54 GB 31 KB
    0 39 extended 54 GB GB partition
    Partition 2 logic 39 GB GB 54
    ---> Note: I do not understand partition 0, there are only two partitions!

    Extract from the event log. Error ID 12289 0 x 80042306:
    The volume shadow copy Service error: unexpected error
    DeviceIoControl (\\?\Volume{6fae1bd1-6bbe-11e2-af9b-806e6f6e6963}
    (- 0000011C, 0x0053c008, 007FB8D0, 0, 007FC8D8, 4096, [0]).  HR = 0 x 80820001,
    The startup file is too small to support persistent snapshots
    Operation:
    Treatment EndPrepareSnapshots
    Context:
    Execution context: System Provider
    ---> NOTE: occurs 4 to 5 times

    Cannot create (process = restore point
    'C:\Windows\system32\systempropertiesprotection.exe ';
    Description is W8 FDC shadow;. Error = 0 x 80042306).
    ---> NOTE: 1 times

    VSS commands: WRITERS, WMI and MSsearch system has failed...
    _________________________________________________________________________
    List writers C:\Windows\System32>vssadmin
    vssadmin 1.1 - Volume Shadow Copy Service administrative command-line too
    (C) copyright 2001-2012 Microsoft Corp.

    Author name: 'Task Scheduler Writer'
    The writer ID: {d61d61c8-d73a-4eee-8cdd-f6f9786b7124}
    Writer Instance Id: {1bddd48e-5052-49db-9b07-b96f96727e6b}
    Status: Stable [1]
    Last error: no error

    Writer name: 'recorder VSS metadata store.
    The writer ID: {75dfb225-e2e4-4d39-9ac9-ffaff65ddf06}
    Writer Instance Id: {088e7a7d-09a8-4cc6-a609-ad90e75ddc93}
    Status: Stable [1]
    Last error: no error

    Writer name: 'Performance Counters writer. "
    The writer ID: {0bada1de-01a9-4625-8278-69e735f39dd2}
    Writer Instance Id: {f0086dda-9efc-47c5-8eb6-a944c3d09381}
    Status: Stable [1]
    Last error: no error

    The writer's name: "System Writer".
    The writer ID: {e8132975-6f93-4464-a53e-1050253ae220}
    Writer Instance Id: {b796dce1-206a-472b-bb86-5417041b341c}
    State: [7] failed
    Last error: Timed out

    Author name: 'ASR Writer.
    The writer ID: {be000cbe-11fe-4426-9c58-531aa6355fc4}
    Writer Instance Id: {eaf13613-1a24-44b5-8622-8e691f1fb074}
    Status: Stable [1]
    Last error: no error

    Writer name: 'writer of Service MSSearch.
    The writer ID: {cd3f2362-8bef-46c7-9181-d62844cdc0b2}
    Writer Instance Id: {43272e0e-d81a-4aa5-abe9-f6bbbfa6f3b0}
    State: [7] failed
    Last error: Timed out

    Author name: 'Shadow Copy optimization Writer. "
    The writer ID: {4dc3bdd4-ab48-4d07-adb0-3bee2926fd7f}
    Writer Instance Id: {20038d53-ecd7-4332-b2f5-ad9a5c465220}
    Status: Stable [1]
    Last error: no error

    Name of the author: "COM + REGDB Writer".
    The writer ID: {542da469-d3e1-473c-9f4f-7847f01fc64f}
    Writer Instance Id: {bf7bd8e4-5aa8-412a-a401-528d6100203a}
    Status: Stable [1]
    Last error: no error

    Author name: 'Registry Writer'
    The writer ID: {afbab4a2-367d-4d15-a586-71dbb18f8485}
    Writer Instance Id: {77018269-1865-4b89-b810-e4a9b6a3b5ab}
    Status: Stable [1]
    Last error: no error

    Author name: 'BIT Writer'
    The writer ID: {4969d978-be47-48b0-b100-f328f07ac1e0}
    Writer Instance Id: {6a7abc2b-e868-45cb-be06-f63e19fb1510}
    Status: Stable [1]
    Last error: no error

    Author name: 'WMI Writer'
    The writer ID: {a6ad56c2-b509-4e6c-bb19-49d8f43532f0}
    Writer Instance Id: {848fabfd-fc83-4c67-ba79-92b274dab8eb}
    State: [7] failed
    Last error: Timed out
    _________________________________________________________________
    Mountvol

    C:\Windows\System32>mountvol
    Creates, deletes, or lists a volume mount point.

    The possible values for VolumeName along with current mount points are:

    \\?\Volume{6fae1bd0-6bbe-11E2-AF9B-806e6f6e6963}\
    D:\

    \\?\Volume{6fae1bd1-6bbe-11E2-AF9B-806e6f6e6963}\
    C:\

    \\?\Volume{6fae1bd6-6bbe-11E2-AF9B-806e6f6e6963}\
    G:\
    ----------------------------------------------
    Lists of C:\Windows\System32>vssadmin providers
    vssadmin 1.1 - Volume Shadow Copy Service administrative command-line tool
    (C) copyright 2001-2012 Microsoft Corp.
    The provider name: 'Microsoft Software Shadow Copy provider 1.0 '
    Provider type: System
    Provider ID: {b5946137-7b9f-4925-af80-51abd60b20d5}
    Version: 1.0.0.7
    _____________________________________________________________________

    C:\Windows\System32>vssadmin list shadowstorage
    vssadmin 1.1 - Volume Shadow Copy Service administrative command-line tool
    (C) copyright 2001-2012 Microsoft Corp.

    Shadow copy storage association
    Volume: (D :) \\?\Volume {6fae1bd0-6bbe-11e2-af9b-806e6f6e6963} \)
    Shadow copy storage volume: (D :) \\?\Volume {6fae1bd0-6bbe-11e2-af9b-806e6f6e6963} \)
    Memory copy ghost used space: 0 bytes (0%)
    Storage space copy allocated Shadow: 0 bytes (0%)
    Maximum space memory copy Ghost: 3.78 GB (7%)

    Shadow copy storage association
    Volume: (c) \\?\Volume {6fae1bd1-6bbe-11e2-af9b-806e6f6e6963}.
    Shadow copy storage volume: (c) \\?\Volume {6fae1bd1-6bbe-11e2-af9b-806e6f6e6963}.
    Memory copy ghost used space: 0 bytes (0%)
    Storage space copy allocated Shadow: 0 bytes (0%)
    Maximum space memory copy Ghost: 3.13 GB (8%)
    ---------------------------------------------------------------------

    Material:
    _________
    Computer brand name: Hewlett - Packard HP Pavilion dv6000 (RG892EA #UUG)
    Operating system: Microsoft Windows 8 Professional build 9200
    Processor: AMD Turion64 X 2 TL - 50 (1600,0 MHz)
    Motherboard: Quanta 30B 8 (nVidia GeForce Go 6100 (C51MV) + MCP51)
    Memory: 2 GB (dual channel)
    Hard drive: FUJITSU MHV2100BH (95 396 MB (100 GB))
    Optical drive: HL-DT-ST DVDRAM GSA - 4084N (DVD + R DL)
    Graphics card: nVidia GeForce Go 7200 [HP]

    Hard drive
    --------------------------------------
    Drive model: FUJITSU MHV2100BH
    Variable speed drive: SATA 1.5 Gb/s
    Drive serial number: NW12T662BYPM
    Firmware revision: 892C
    Disk capacity: 95 396 MB (100 GB)

    Hi Francis,.

    Thanks for posting the query on the Microsoft Community Forum.

    From the description, it seems that the error revceive you associated with VSS snapshot.

    1. What security software is installed on the computer?
    2. Do you have any third-party backup program installed on the computer?

    To begin troubleshooting, I would suggest that you do Check Disk

    • Press Windows key + R
    • Type "cmd" to open the command prompt.
    • Type Chkdsk/r , and press enter.

    Note:

    If all available hard disk data can be lost when running chkdsk, as the chkdsk attempts to repair the affected area.

    Reply with more information about the issue so that we can help you further.

    I had the same problem with a HP dv5000 has an Intel Dual Core processor, after installed the 10 Pro Update window cleaning, after the update sent by Windows Update Service left me with this problem.

    Thank you post I did check in the menu properties C: Tools.

    After that, I was able to create a Restore Point.

    Thank you very much for your message.

  • Unable to get the Bluetooth Toshiba BT Stac Headset profile in collaboration with mic

    Hello.

    I have problems with my Motorola HT 820 Stereo headset, the Toshiba Bluetooth Stack installed on Vista Home Premium 32 bit laptop.

    I am unable to get the microphone to work at all, so can't use it for Skype / VOIP calls etc. Features such as the A2DP and AVRCP work very well, and I can listen to music via the media player without problems.

    I read in a FAQ on this site, to make sure that I use the installation option custom rather than the quick installation when adding the device, but it seems to make no difference, am I missing a step here?

    In the properties of the device Windows registry, I see the option listed for Bluetooth Mic, but even assigning as device by default does not work.

    I know to plug my headphones on my desktop PC that uses the bluetooth stack Widdcom, can I use the headset/microphone function, but this battery seems to work differently, as I can select option headphones in the bluetooth settings, but I don't see such an interior option Toshiba stack - and I think that's the problem.

    I've updated to the last stack of Toshiba on this website, but this did not help at all.

    Here, any help would be appreciated.

    Concerning

    Matt

    Post edited by: Toxyturvy - wrong spelling

    Hello Matt

    Unfortunately I can't help you with that, but if I remember right here on the BT section that someone has already asked something similar. Please take a little time and see the BT section on this forum.

    You can also visit the FAQ section on http://aps2.toshiba-tro.de/bluetooth/
    Might find something there.

    Good luck!

  • Unable to get the automatic updates of Windows.

    Suddenly I'm unable to get the automatic updates of Windows.  When I use Windows fix - it, it is unable to do so, stating that automatic update components need repair.  Is there a way to repair the components?

    Hi Robert,.

    Reset windows update components.

    http://support.Microsoft.com/kb/971058

    Use the automated fix solution, then check windows update to see if it works.

    Additional information: If you are not fully patched for Windows XP SP3, download and install Windows XP SP3 from the link below.

    Windows XP SP3.

    http://www.Microsoft.com/en-US/Download/details.aspx?ID=24

    Ignore the warning text on the professionals and the network installation.

  • lost all the restore points after the reinstatement of windows

    Original title: have just re-recorded windows software, now Ifind I lost all the restore points. How can I get the old one back?

    Windows has been registered online. Checked restore points after recording and found that the only listed restore point was created when the software has been registered. How can I find the previous restore points?

    If you reformatted and reinstalled windows, you will lose any restore points. Theyre gone

Maybe you are looking for