Unable to install the driver from the iPhone to my computer.

Similar Questions

• HP Officejet 4630 is unable to install the driver. Windows XP Sp3

  Good evening

  I bought this printer earlier today and a few hours already on this issue. The box is not too far away, and the printer could come back soon!

  The printer works fine, it was connected to my router, the light is always on, it says connected to the wifi system. Print the confirmation of wifi connection page, everything is 'Success'

  My problem is that whenever I try to install the drivers, the research of setting up a printer that is connected but not yet installed. He notice my printer with the right ip address, then copy the driver of a couple files and then tells me it is unable to install the printer.

  The current configuration is OJ4630_198, I found an older version and tried it but roughly the same results, except that before it stops the installation telling me he fails to do so, it asks me to locate the HP CD on my cd player, looking for a fax facility facility .png but fails a second later.

  I am naïve enough, I tried to install it manually, but of course the Communication Port is a little tricky with a wire less printer.  I noticed there's a selection of "Create a new port" available in which appears an option named "Hp discovered Port Monitor (HP 4630 series)" which curiously is my new printer. Tried but it doesn't work.

  I reset my router and printer, pc several times, tried to assign my printer to another port number, all ended with the same results. It connects to my wifi, but I can't seem to install the printer driver.  So my list of printers is empty atm...

  Thanks for any help,

  Very appreciated

  Windows XP Sp3

  Cisco router

  ZoneAlarm firewall...

  Well, problem solved.

  It is indeed a Windows problem.

  Thanks to SAM from live chat assistance, he noticed the HP Installer wasn't working, so we tried to manually install the printer with the tcp/ip Protocol and former driver windows Xp Announces (deskjet 990c) who worked...

  I hope that everything is still functional. But Kudos to SAM for a helping hand.

• Of VMware Remote Console Plug-in Setup error: "unable to install the hcmon driver."

  Hi all

  I try to install the VMware Remote Console Plug-in for my browser of 32-bit Internet Explorer 11, and I get an error message during installation: "Unable to install the driver of hcmon."

  I have Windows 7 64 bit with .NET installed 4.5.5. Anything installed in my device manager, there is no hcmon.

  I use an x 86 install files to VRMC (VMware-vmrc-win32 - x 86 .exe), but I guess that this 32-bit version is what I want because I use THE 32-bit? Or is that what I want 64-bit for my OS?

  I've seen some posts related to this issue, but all my registry keys seem to be set correctly and my .NET is of course more recent than the version 3.5 SP1, but I hope it's OK.

  Also, I got an error on the USB in my Windows logs Arbitration Service, but following the steps described here, and retry the installation also failed with the same error 'hcmon' described above:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 2043656

  Any ideas on what might occur, or other things I can try?

  Check if these KBs contributes to:

  http://KB.VMware.com/kb/2053281

  http://KB.VMware.com/kb/2006486

• "Unable to install the plugin from RoboHelp for FrameMaker...." »

  Hi-

  I have 9 Frame and a copy of RoboHelp 8.0.0.203 demonstration and works in Windows 7 (all of a sudden. Yet to learn my way in the operating system after a catastrophic failure of the weekend with my trusty little machine XP.) I have no TCS2; just these two stand-alone tools. I have a book of frame I need to turn into contextual HLO and am auditioning Robo for the task.

  No dice. Whenever I try to import (see below re linking) I get an error message in a box marked "RHUtils": "unable to install the plugin from RoboHelp for FrameMaker. If please close FrameMaker and try again. »

  
  With your permission, I'll cover a few points in the order in which they come to mind:

  == > Initially I tried linking, hoping of course to the advantages of the single-sourcing. I learned in this forum and elsewhere (-btw, thanks for this great resource) I need the TCS2 in good faith in place to connect. Thought that I could import for now instead of it, just to see how it happened; received the same error message.

  == > It was AFTER I had done the research and on the Adobe site (http://www.adobe.com/support/robohelp/misc.html) found this: "the plug-in for RoboHelp, FrameMaker FrameMaker users allows quickly convert any number of books for a simple import or FrameMaker files in RoboHelp 2002 and X 3.» RoboHelp X 4 includes the plug-in! For RoboHelp, FrameMaker plug-in is only available for Windows. To install the plug-in, unzip the RoboMIF.dll into the Plugins folder in the installation of FrameMaker folder (normally found in C:\Program Files\Adobe\FrameMaker7.0\fminit\Plugins)...   Once the plug-in has been installed, restart FrameMaker. FrameMaker now includes a RoboHelp menu. "OK: I have downloaded RoboMIF.dll, installed according to the instructions, rebooted just in case, and now"Adobe RoboHelp"actually appears in the menu bar in the frame. I however always the error message whenever I try to import (now).

  
  == > For several of these attempts Frame was indeed closed. For several other Frame opened to the entry page and nothing else. No apparent effect, anyway.

  
  == > Import and link Word files seems to work very well - which is cool, but my document is in frame at the moment. I know I can convert, but up to now to convert the word seems to need to get all references, what I did in the framework. Doable but not my first choice.

  
  == > I found a thread of editors at http://www.mail-archive.com/[email protected]/msg18576.html / / www.mail-archive.com/[email protected] msg18576.html relating to this problem. The recommendation, (published here for brevity), who was the author:

  1. locate [the] Maker.ini file and ideally make a backup of it, just in case.
  2. in the [APIClients] section of the maker.ini file, add the following line:

  RH4FMver9 = Standard, RH4FMver9, C:\Program Files\Adobe\Adobe Technical Communication Suite 2\Adobe RoboHelp 8\RoboHTML\RHFrameMakerServer9.dll,all

  3. you should now be able to launch RoboHelp and 'link' files, FrameMaker, FrameMaker application should launch correctly.

  This doesn't seem to be my answer because I don't yet own TCS2. This path does not exist.

  (I still get excellent advice of training provided by this answering machine, RJ Raquez, to http://blogs.adobe.com/rjacquez/2009/05/linking_framemaker_9_books_in.html.)

  In any case, this is where I realized that I was, at least for now, of ideas. Does anyone have more?

  Thank you-

  Anne

  If you do not want to go down the road of miftogo mentions Arnis, you can always download the demo of TCS2 - it is fully functional for the period of the demo. I am tempted to install it in its own virtual machine (or another machine entirely) so that you do not get the demo interfere with your legitimate copy of FM9.

• Bing bar 7.00 is unable to install the update error 643

  Bing bar 7.00 is unable to install the update error 643

  How to ask a question
  http://support.Microsoft.com/kb/555375 >

  It helps those answering questions if you provide:

  what the version of windows (32-bit or 64-bit) and service pack level.

  you use what browser (exact version).

  what application anti-virus or security suite is installed and your current subscription?

  What third-party firewall

  What software anti-malware can be installed.

  What updates you trying to install? (Number of KB)

  Please do it in your next reply.

  `````````

  DON'T APPLY TO WIN7

  A KB has been created for the x 0 80070643 or error code 0 643 x that appears when you use Microsoft Update or Windows Update Web sites to install updates. The KB includes an automated Microsoft Fix it 50473 that corrects the problem. Look at the following KB: http://support.microsoft.com/kb/958052>>

  Suggest you download and save the fix it.

  Then close all open programs and browsers before running MS fix 50473.msi.

  `~`

  03/18 / 1105:46: 22:00

• Unable to install the update to windows? 0x800A01AE & 0 x 080070570

  Unable to install the update to windows? cordially 0x800A01AE & 0 x 080070570, Sohail Patel "MCSE 2003 | ITILv3 | "A journey of a thousand miles begins with a first step."

  http://support.Microsoft.com/kb/910359

  Manual procedure to solve the "0x800A01AE" or "0 x 080070570" error messages to manually resolve this problem, follow these steps:

  1. Stop the Background Intelligent Transfer Service and the automatic updates service. To do this, follow these steps:
     1. Click Start, click run, type cmd, and then click OK.
     2. At the command prompt, type the following commands and press ENTER after each command:
        net stop wuauserv
        net stop bits
        output
  2. Rename the Catroot2 folder.

     Note Do not follow this step if you are using Microsoft Windows 2000.

     To rename the Catroot2 folder, follow these steps:

     1. Click Start, click run, type cmd, and then click OK.
     2. At the command prompt, type the following commands and press ENTER after each command:
        
        net stop cryptsvc
        Ren %systemroot%\System32\Catroot2 oldcatroot2
        net start cryptsvc
        output

     Important Do not rename the folder C:\windows\system32\catroot. The Catroot2 folder is automatically recreated by Windows, but the C:\windows\system32\catroot folder is not recreated if is renamed the folder C:\windows\system32\catroot.

  3. Rename the folder "C:\Windows\SoftwareDistribution":
     1. Click Start, click run, type %any, and then click OK.
     2. Right-click the C:\Windows\SoftwareDistribution folder, and then click Rename.
     3. Type SoftwareDistribution.old, and then press ENTER to rename this folder.
  4. Save the files used by Windows Update and Microsoft Update. To do this, follow these steps:
     1. Click Start, click run, type cmd, and then click OK.
     2. At the command prompt, type the following commands, press ENTER after each command, and then click OK every time that you receive a verification message:
        regsvr32 c:\windows\system32\wuapi.dll
        regsvr32 wuaueng1.dll
        regsvr32 c:\windows\system32\wuaueng.dll
        regsvr32 c:\windows\system32\dllcache\wucltui.dll
        regsvr32 wups2.dll
        regsvr32 c:\windows\system32\wups.dll
        regsvr32 wuweb.dll
  5. Start the service of automatic updates, Background Intelligent Transfer and the event log service. To do this, follow these steps:
     1. Click Start, click run, type cmd, and then click OK.
     2. At the command prompt, type the following commands and press ENTER after each command:
        net start bits
        net start wuauserv
        net start Eventlog
        output

        Solved...!

  Best regards, Sohail Patel "MCSE 2003 | ITILv3 | "A journey of a thousand miles begins with a first step."

• Virus & spyware definitions update failed. error code: 0x8024402c. Error description: Microsoft Security Essentials was unable to install the updates of definition, because the proxy server or target server names is not resolved.

  Virus & spyware definitions update failed.

  error code: 0x8024402c.

  Error description: Microsoft Security Essentials was unable to install the updates of definition, because the proxy server or target server names is not resolved.

  Here is an article that meets your specific error message regarding updates:http://support.microsoft.com/kb/900936.  I am surprised that the error occurs with all the updates, but there may be a difference between them that causes the problem for definitions, but not for others.  I hope that this will solve the problem.

  If this does not help, please transfer your question in Forum Windows Update:http://social.answers.microsoft.com/Forums/en-US/vistawu/threads where updates experts will be happy to help you.  Please post with the information requested here:what to post in the Windows Update forum

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I'm unable to install the updates on my system

  I'm unable to install the updates on my system. Arte updates installed, but they are not configured properly so changes are returned and the end system day are not up to date please help. Thank you

  Hello

  see if that helps to fix:

  How to reset the Windows Update components?

  There is also an automatic 'fix - it' here

  http://support.Microsoft.com/kb/971058

  Also, try to put the KB numbers in the search on the link below and then manually download the

  http://www.Microsoft.com/downloads/en/default.aspx

   

  or please repost your question in the correct windows update forum

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all

• I'm unable to install the Microsoft. NET Framework 4 client for windows 7 X 64 profile base system. Any ideas?

  Original title: Microsoft. NET Framework 4 client for windows 7 X 64 profile base system

  I'm unable to install the Microsoft. NET Framework 4 client for windows 7 X 64 profile base system.

  Any ideas?

  Thank you.

  Hello

  Thanks for posting your query on the Microsoft Community.

  I understand that you have a problem with the installation of Microsoft. NET Framework 4 client profile. I will certainly help you in this matter.

  Provide us the following information to better help you.

  • Have you made changes on the computer before this problem?

  • You receive an error message/code?

  Follow the below methods:

  Method 1:

  The .NET Framework 4 Client Profile is available on Windows Update
  http://support.Microsoft.com/kb/982670

  Follow the method 1 and method 2 in the article and check for the issue. If the problem remains same follow method 2.

  Method 2:

  Disable the .net framework Windows feature on or off, follow these steps:

  a. click the Start button, select Control Panel, click programsand then click Windows turn on or off features. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  b. to turn off .net framework, click the media feature. And the .net framework and click OK.

  c. restart the computer to apply the changes.

  Note: follow the steps above to activate or activate the .net framework and check if the problem occurs.

  For more information, refer to this link turn Windows features turn on or off:

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-features-on-or-off

  Please let us know if you need more assistance.

  Thank you.

• I'm unable to install the drivers for the Intel CS630 PC camera for windows7 64-bit?

  I'm unable to install the drivers for the Intel CS630 PC camera for windows7 64-bit?

  If it's a camera for INTEL it website should have the good

  64-bit to Win 7 64 bit software.

  Some older hardware will not work on newer 64-bit systems.

  check your websites of manufacturers of games for win7 64 bit compatibility.

  Try your game in compatibility mode in Windows 7.

  to say the least there are a huge amount of games and

  software that works fine with Win7 64-bit.

• I'm unable to install the software on my new Surface RT nook study to access a manual

  I'm unable to install the software on my new Surface RT nook study to access a manual while I'll be away next week.

  "Nook" is in the Windows store, but not 'study of the corner. " Is there a work around to read my etext on my RT? I'm willing to try anything.

  Original title: nook survey application

  Microsoft them does not limit in any way: Nook is absolutely free to provide the study Nook Windows program, and encourage Microsoft to do.

• I have CS5 drives that were installed on an old laptop which is dead. I would like to reinstall this product on a new computer. I installed the disks on my computer, but I can't activate the product. Can you help me get a new serial number?

  I have CS5 drives that were installed on an old laptop which is dead. I would like to reinstall this product on a new computer. I installed the disks on my computer, but I can't activate the product. Can you help me get a new serial number?

  As far as I know, Adobe won't give you a new serial number

  Mac or Windows and EXACTLY what version of the operating system?

  Recent Mac AND Windows operating systems have been known to cause problems "weird."

  Invalid License http://helpx.adobe.com/creative-suite/kb/error-serial-number-valid-product.html

  -http://helpx.adobe.com/creative-suite/kb/invalid-serial-number-cs4.html

  - and http://forums.adobe.com/thread/1038761

• I'm unable to install the Prime Minister the elements of the trial.

  I'm unable to install the download to test components of Prime Minister.  I have a Mac.  He continues to tell me that "Setup has encountered a problem that caused the installation to fail.  Contact the manufacturer of software for support.  I followed all the advice on the troubleshooting page, but have the same results.  Any suggestions?

  OK, then I suggest that you contact our support staff at the following link: https://helpx.adobe.com/contact.html

  (be sure to connect to adobe.com with your Adobe ID first)

  Kind regards

  Guinot

• I had to uninstall flash player, but am unable to install the update.  I have reset the Mac Book but am still unable to install the update.

  Safari: Version 8.0.6 (10600.6.3)

  Mac Book: MacBook Pro (retina, 13 inch, mid-2014)

  I had to uninstall flash player, but am unable to install the update.  I have reset the PRAM book Mac & NVRAM + SMC re-set, but I am still unable to install the update via Safari or FireFox

  Still due once sort myself

  I downloaded the offline install app;

  http://fpdownload.Macromedia.com/pub/flashplayer/latest/help/install_flash_player_osx.dmg

  Up and running

• Get "unable to install the VirtualCenter Agent service" on ESX 2.5.4 after the upgrade of the VC to 2.5 update3

  I have improved my Virtual Center 2.5 to 2.5 update 3. After doing this, I have 2 of my ESX v2.5.4 servers which will not reconnect.

  I get the error message "Unable to install the VirtualCenter Agent service". I also see "the connection failed due to a bad user name or password" showing upwards in the list of tasks of VC. I don't know that I type in the good user/pass as I turn around tight and SSH on the server using the same user/pass.

  I tried to do "service vmware-vpxa restart" on the hosts. What log file I look in upon the host server to find the real problem, and is there any other suggestions on a quick fix to try before the word is supported?

  Thank you.

  Here is a good link that will help you in the installation of officers

  http://VMware-land.com/Vmware_Tips.html#ESX6