Update firmware for USB-6501 with 3.4.0 driver?

Similar Questions

• Unable to update firmware for the PERC 5 controller / i on PE1950

  We have 6 PE1950 server with SAS PERC 5 / i integrated RAID controllers. Dell OpenManage complains about being obsolete PERC firmware. 2 servers I currently have running, firmware 5.2.1 - 0062 and 5.1.1 - 0040. I downloaded the latest version of 5.2.2 - 0072. I tried the update by the Windows package and who did not, and he complain about the OS being too recent. A server is Windows Server 2008 R2 and the other Windows Server R2 2012. So, I created a BACK USB key with Dell hard drive files and run update.bat. Who failed on both servers with the following errors:

  Firmware doesn't have flash. Stop!

  Failed to update Firmware for controller 0

  The process of updating of the firmware of the controller does not have!

  Both servers had the exact same mistakes as described above. Ideas on how I can get the firmware update successfully? I checked the package I downloaded is for the PERC 5 / I integrated.

  It's here (if that will allow me to post a link):

  www.dell.com/.../DriversDetails

  Hello

  Try this updated version and see if it works. He said that it was for the 1950s.

• Best way to generate the software clock for USB-6501 of Measurement Studio for c# VS2008

  Hi all

  I wonder if there is a better way to generate a clock software for USB-6501 of Measurement Studio for VS2008 in C Sharp?

  I have developed a clock using C Sharp "Thread.Sleep (msecPauseTime)"; and statements to switch digital output high and low. There are a few things I noticed in creating a software clock in this way:

  1. The smallest delay by the Thread.Sleep command time is 1 millisecond (which means higher clock period is 2 msec-500 Hz, not holding not ball account no. 2 below).
  2. Sometimes the delay I see on an oscilloscope is considerably longer than the delay that I specified in the sleep command.

  In my application, I create signals (a clock, a latch enable and data series) to control what an attenuator step through the USB-6501 RF connected to a USB 2.0 on my computer. This particular step RF attenuator can accept clocks with frequencies up to 10 MHz, so I would like to generate a software clock (without having to connect to an external clock to a line of input on the USB-6501) which is closest to this maximum frequency, and I think that the USB2.0 line could handle clock speeds over 500 Hz. Also, I would like to know why the delays that I see on the scope are sometimes longer than the time specified by the Thread.Sleep command. Is it caused by the suspension of the execution of my program processor for something else, as I suspect? Of course, this isn't a big deal, because it does not affect the time as my serial data and pieces change compared to my clock. However, I would like to know why it does this.

  I appreciate your help.

  Thank you

  Jonathan Becker

  Doctoral research engineer

  Carnegie Mellon Silicon Valley

  Jonathan,

  Since the USB-6501 DIO is software programmed, you are at the mercy of the planning of the operating system and won't be able to work reliably with an external clock in the software.

  You can try to set the priority of your thread 'generation of clock' to improve performance, however, because Windows is not a deterministic operating system, there are still no guarantees.  Operating systems are not required to honor the priority of threads.  You can find examples and information on the definition of the priorities of the threads in c# here:

  http://msdn.Microsoft.com/en-us/library/system.Threading.thread.priority.aspx

  Kind regards

• Y at - it updated firmware for the m3 RX100

  Sony makes updates firmware for their cameras ie; RX100 m1/2/3, like to know before you buy one. Many sites seem to believe that it is rare that their cameras updated firmware. Cheers in advance

  Hello Oriley59,

  There is no update firmware, but made for the three models RX, you talked and it is difficult to assume that an update will be released soon.

  If my post answered your question, please mark it as "accept as a Solution.

• Trouble with USB-6501 with Labview 8.6 Pro for Mac OS

  Hello

  I have a unit USB-6501 I try to use with Labview 8.6 for Mac Pro to processor intel.

  I have the driver NOR-DAQmx base 3.2 for Mac installed and when I ran "Isdaq", it detects the device and also warned that the firmware needs to be updated. So, I ran the "FWUpdate" for updating the firmware. I double check the Isdaq and it detects the device as "NI USB-6501:"Dev1"(USB0::0x3923:0x718A:014386 B 0: RAW).

  Now, when I run Labview 8.6 and DAQmx Base create channel VI and the port of 'physical' wire to the control, nothing appears in the available device.

  Also, when I run the mxbaseconfig program, not the existing basic tasks detect the device.

  Could someone please help me get this to work? Basically, I need to read and write slow digital data through USB-6501. But, the Labview does not detect the device.

  Thank you

  Keong,

  I do not know what causes this, but place a task create VI before your code and the wire of the output task to the task of entering the chain and try to run that.  Please let me know if it works for you.

• Workstation HP Z240 tour: update Firmware for Z240

  Workstation HP Z240 Tower
  Product number: L8T12AV
  
  To update the Firmware, I provided this link by the customer support:
  
  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=8323794&swItemId=wk_158289_1&swEnvOid=419...
  
  Using the link, I was able to download and run sp74202.exe.
   
  A set of instructions then appear as follows:
   
  Another utility of FWUpdLcl.exe in the directory of Mee Flash\Local-Win is designed to update the ME firmware in an environment 32-bit or 64-bit Windows, the "Run" box or a command prompt. Her can be updated by running the following command: "FWUpdLcl.exe - f... \11001197.bin-generique. In addition, when you run a 64-bit Windows environment, use the command: "FWUpdLcl64.exe - f... \11001197.bin-generique. ME Flash contains the binary update image for use with the utility.  The binary image of the update and the content of the file room for both parties can be copied to any volume of storage available in the Windows operating system.
   
   
  Since I'm on 64-bit Windows 10 I guess I need to run the command: FWUpdLcl64.exe - f... \11001197.bin-generique
   
  My question is... How can I fill this order, that is, how know what folder to look at, to find the files.

  Many thanks for the advice.

  When you run HP service packs, they will enlarge and place their content under a clean directory in C:\swsetup.

  Specifically, in your case, if you are running sp74202.exe, you should see a new directory that c:\swsetup\sp74202 was created with the contents of the service pack to the breast.

  You can also use 7-zip to look inside the service pack exe without running from the exe is a zip file that runs the installation program once unzipped self-extracting

  In any case, is a more recent version update ME here , but first of all, I would apply the latest system firmware update available here.

  When looking at service pack HP above links, it is advisable to selectively click on each 'Description' and 'Improvements', 'Instructions of Installation' 'Release Notes' 'fixes' tabs 'History' and read the information (some of it is repetative, but you'll soon learn where to focus your attension).

  The content of these tabs contain important and relevant information on what has been improved, corrected, what system it is, how to install the update, etc. And if one SP installed previously is not listed in the tab 'historic' liberation may have been driven by HP due to certain behaviours fauly or another question!

  Attension pay including prerequisites in some cases of updates must be reinforced (is that you can always just apply later).

  And if you read these things boaring, tab Instructions of Installation of the firmware (BIOS) system would have given you a clue where the sp files are extended to the

  Have you tried simply enter the command (as shown) via a command prompt window and change the directory where the FWUpdLcl.exe file is located?

  Just keep in mind that sp74202 is the initial ME firmware release is nothing so sould update

  So best to apply the latest firmware system (BIOS), then the ME firmware, then maybe later ME software (under chipset drivers).

  Better to mark this page that lists all downloads for your 64-bit of Windows 10 z240 Tower system then see him regularly.

• Need to update firmware for drive HDDVD of Satellite P200

  I bought my P200 - 17 c, 3 months ago. I tried to update my Firmware apparent more later (TO35).
  However I can't because I don't have any other installed TO33/TO34. After checking my FW version is TO04! ????

  How can I get previous versions so I can upgrade to the current version. I find it very odd that the current versions do not earlier versions already have with her.

  WHERE CAN I FIND THE FIRMWARE BACK TO THE SATELLITE P200?

  First that you check if you Satellite P200 has been equipped and supplied with the TS-L802A drive because TO35 firmware was designed only for this drive.
  You should know that the P200 series was delivered with different readers and not all support the TS-L802A ;)

  Please check first!

• updated firmware for the clip and clip +.

  Hello

  I have an old Clip 4 GB firmware v 01.01.29A and a Clip + 8 GB firmware v 01.02.15A. I see that these are outdated versions and newer versions are available. I've never updated the firmware, so I was reading the messages to see how. Here's my question; I read that to remove FM Radio you should 'drop' the 'A' in the update. I see that the updates do not have the letter 'A' affixed. This doesn't mean no FM Radio more if I update the firmware for both of the clips? I don't want to lose the radio.

  Thanks in advance for any help

  I wouldn't bother with updating the Clip +. There is very little has changed since the version.15. It's the one I always use on mine.

  No, you won't lose the FM radio by updating the firmware. You must have read some old posts.

• Cannot update firmware for Officejet Pro 8600 N911a

  I can't upgrade the firmware in my Officejet Pro 8600 N911a.  My current firmware is CKP1CN1416AR.  According to the HP drivers website, the latest firmware is CLP1CN1322CR.  I get the update to run and it identifies my printer, but it won't let me select it.  I use the printer on a wireless network, but I'm trying to run the update of the firmware via USB.  Any help would be appreciated.

  Sunshyn2005,

  Please provide information on this issue.

  Apparently, the problem that your customers have is that they are wasting their time trying to update the firmware on their printers and after a few hours of frustration they finally know that HP has a firmware update file on its Web site that has a date that is much newer than the firmware itself.

  HP should do the following to make the process less frustrating firmware update:

  1. establish dates and version numbers in the file metadata which clearly indicate what firmware file is more recent.

  2. keep the HP web site up-to-date with the latest versions of firmware.

  3 Broudly and transparent announce to the public when an update will be made and why.

  4. establish technology so that firmware can be updated on wireless links so that the networks do not have to be reconfigured to make the firmware updates.

• Update firmware for HX100V?

  Request for update of firmware for HX100V to include photography in fast motion in the film section. Now I can record in 30ps (MPEG4) or 60ps (AVCHD). It should be possible to allow flexible adjustment for slower frame per second to produce the same photograph of time-lapse effects. No necessary intervalometer. My cheapie GE X 5 camera have intervalometer setting for interval of 30 s, 1 min, 5 min & 10 min. Kind of sad to see that you missed this feature in a perfect unit for photography accelerated. Get there in the guy.

  Thank you for your post and welcome to the forum.

  I forwarded your suggestion to the applicable to review Sony team in a future update.

• OfficeJet 4620: update Firmware for officejet 4620

  My scanner does not work, and I thought I had the latest firmware would solve. Where can I get the update of firmware for officejet 4620? I found something under the software and drivers, but I don't know if it's the same thing.

  Hi @elianab.

  Welcome to the Forums of HP's Support.  I appreciate that you try to update your firmware 4620's.

  You can download the latest firmware for printers from the HP site.  Scroll down and select the Firmware.

  Here is a link to the page drivers 4620. HP Officejet Firmware CWM1FN1451AR 2.3 MB December 6, 2015 is the latest / up to date firmware.

  Do you receive error messages when you try to scan? I can perhaps more assistance on this issue.

  I would like to know the link worked for you. If it did, that's great! Give us some reinforcements by pressing buttons of solution and laurels, that we will help and others see that we have the answers!

• Y at - he liked an update firmware for the sansa clip

  If I use the sansa updater it detects it as a normal element and gives me a firmware to install, one that ends in 32 I think, but if I install what I think ill ruin the clip, so I ask if a firmware update for the clip more were released, I got V01.01.05A firmware now

  No update firmware at the moment; you have the most recent.  If/when an update of the issues, it is likely is displayed as a sticky thread at the top of this forum.

• Updates firmware for the isa550w

  y at - he's going to be more updates of firmware for the isa550w or a cisco decide to stop making the deadline of November 14, 2014? I know that this product is reached it's end of life cycle soon not if cisco decides to make the updates of firmware for this product earlier than November, it would be good to know

  link to your solution two to the following: -.

  http://www.Cisco.com/c/en/us/products/collateral/security/small-business...

• Updated BIOS for a boot with USB (external)?

  I have a laptop of G50-104NR with Windows Vista Home Premium.

  It doesn't seem to be a BIOS update available at HP when you run the update from HP. As best I am able to determine, the BIOS does not support boot from an external USB device. Does anyone know of a source of an update of BIOS or other workaround to allow booting from a USB device?

  Thanks in advance.

  the update of hp does not always show the BIOS updates.

  Enter your product number in the search box at top right of this page, select software downloads and the pilot, then the OS you are using.

  you will then to the drivers page for your laptop.

  most of the newest BIOS of HP usb Boot support

• Satellite A30 303: no update firmware for drive UJ-811 H100

  Hello!

  I have model witch toshiba A30-303 have mast * one optical drive UJ-811 H100, I have this laptop for over 2 years and I have strength to find any update on this drive I n even know if this company exists (matsu * a).

  I've changed this disc about 5 or 6 times with a new period of warranty due to reading problems.

  I'll be happy if someone knows something about the update of this player

  GEIA sou Taso,

  Matsu * one is the same company that PANASONIC which is more known for us. The UJ-811 is a quite old model (3-4 years) and very well known problems.

  You forgot to mention in your post...
  (1) exactly, what is not working on your disk (writing? read?) DVD? CD? Movies?) and also
  (2) why do you think a firmware would solve your problem. (he has none)
  (3) how often and for what purpose do you use your car,.
  (4) and finally to what type of physical environment (home? mobile? dusty?) that you are using your laptop.

  Be aware, that optical readers get very easily breakable, especially when it is used for watching/rip movies on them or access the drive streaming of games. Another possible reason would be a wrong installation / incompatible software on your PC that can cause the drive not to work properly (or even disappear).

  You can try to 'clean up unused software' on your laptop and also to put a soft recovery to check, if your CD drive will be properly again. If the problem will not go away, you need to exchange it for a different brand new maybe even one (it was 5 times that a PANASONIC drive is broken?  ;)). If you are a heavy user of DVD player (movies, tearing, Burning, blah) you should ALSO get yourself a USB external... they hardly ever get broken, are faster and more reliable, and are much less expensive to replace. One of my friends who had already 3 discs replaced in his book could confirm as the best solution.

  Kind regards
  chain