Updated power supply with h8 - 1360t (after installing HD 9750 / 3 gb)

Similar Questions

• Pavilion HPE H8-1121: Pavilion HPE H8-1121 - new graphics card + power supply does not start after screen HP (Revisited)

  I have the same problem as this post 2013!  Ouch. Pavilion HPE H8-1121 - new map chart + power supply, does not start after HP screen.

  I installed a new power supply (Seasonic 620W), which works well.  I also installed a GTX 660Ti last year and it was works fine as well.  I recently bought a ZOTAC GTX 970 and attempted to install it, but it will not go beyond the blue HP screen and I get the same code of beeps (1 long, 3 short), who, seems, suggests that the video is not initialized.

  My BIOS date is 2011.

  Where can I find an update for this?

  I'm also using Windows 10, which I found on the HP site is not tested on my model and would probably not favourable to good use.  Should I do back up to 7 or 8?  and then update the BIOS?  Y at - it a update for my BIOS and where can I find.

  In any case, I hope that this is a solution.  Again, this is not a bad machine to be 5 years old.

  Thanks for any help!

  If the video card that you have purchased dose not a legacy vBIOS it will never start. An update of the BIOS doesn't solve that.

  It is likely that your new video card has a vBIOS UEFI and that only is for the PC motherboards newer than yours which have a UEFI BIOS. Your motherboard has a legacy BIOS. 2012 is the year of model when the UEFI BIOS more or less became the de facto on motherboards standard.

  I return it for a refund. Find the candidate of video cards that support the old BIOS. It can be inherited only or switchable vBIOS (legacy or UEFI) vBIOS.  I suggest looking at the site of Sapphire Technology. ZoTac is not known to provide enough information about their video cards in the way. You upgrade a pre-built desktop PC and it's different and a little more difficult to set up a DIY PC. I looked at the site of Zotac and see that nothing is said about their video vBIOS cards.  I would return to the map.  Carefully read the specifications of the video card. A candidate for your motherboard card must have inherited vBIOS support or simply, it won't work.

  ZOTAC (they don't say anything about their product vBIOS)

  https://www.ZOTAC.com/us/product/graphics_card/GTX-970-amp-extreme-core

  Sapphire Technology

  http://www.sapphiretech.com/catapage_pd.asp?cataid=305&lang=eng

  Because you look at game with 4 GB cards. Take a look at the following map. It has a double vBIOS. legacy and UEFI. http://www.sapphiretech.com/productdetial.asp?pid=640A98CD-0CF0-4191-B75C-CA2800111ADB&lang=eng

  

• I have a p6210f (Win 7), that does not illuminate. As recommended, I tried a new power supply with the same results.

  In my post in November, I explained that I had tested the power supply with a multimeter and read the correct voltage. Two people to the Board of Directors always seem to think it was the power supply, so I replaced it with a new one (Corsair CX 430 R) and it still won't turn. I had suspected the power switch because when I bypass the MOBO 20 pin plug 'on', the power led lights up, fans have come on short and I heard the rotation of the disk. I also tried to troubleshoot the switch by jumpering the pins on the motherboard, but still no luck. Someone there ideas more before I replace the card MOTHER and CPU? Thanks in advance.

  Roamstead

  Cloud_strider,

  Thanks for the reply. After swapping the PSU, CPU, taking the RAM pins on jumping on the MOBO for power/LED/reset button, each separately and with the same result, I eventually swapped the MOBO to an ASRock A785GM - THE and who did! He finally put under tension. Thanks again.

  roamstead

• did someone had problems with lightroom 5 after installing Mac OS El Capitan?

  did someone had problems with lightroom 5 after installing Mac OS El Capitan? the images are well n the library but darken when I switch to develop fashion

  It's a shame that you did not check for problems before you can update your Mac

  First, see if the update to the fixed bug Mac 10.11.1 will help you

  -an exchange of views of 10.11.1 https://forums.adobe.com/thread/1986008

  -In ADDITION the need to update the drivers nVidia (links included in the message)

  -There is also 'a' mention of an another 10.11.2 bug fix tested by Apple

  He has problems with Mac 10.11 El Capitan... which is perhaps one of them

  See answer #5 in https://forums.adobe.com/thread/1965850 for several solution links

  -the first link that the answer is a possible solution to install problems

  -There is also a link on the video display problems in Premiere Pro

  - and many other programs... MORE Microsoft Office also has problems

  More official Adobe help pages listing problems Mac 10.11

  https://helpx.Adobe.com/Photoshop/KB/Photoshop-and-El-Capitan-Mac-OS-10-11.html

  http://blogs.Adobe.com/PremierePro/2015/10/Premiere-Pro-CC-and-Mac-OS-x-10-11-El-Capitan.h tml

  https://helpx.Adobe.com/Lightroom/KB/Lightroom-and-El-Capitan---Mac-OS-10-11.html

  http://blogs.Adobe.com/audition/2015/10/audition-CC-and-OSX-10-11-El-Capitan.html#.VjjYBtG raUk

• Can power supply Question - I use the 230W power supply with a W540?

  I have a W540, which currently uses a power 170W (8.5 a 20V)

  I got also a docking station for a P50 that has a power of 230W showing 20V 11. 5a.

  The connectors are similar, but I'm hesitant to try the 230W power supply in the W540.

  It is allowed to use the 230W power supply with the W540?

  230 watts is maximum power feeding, it only provides the energy required by the computer.

  I sold my W540, so I can't test it for you. But I do use the ThinkPad X 1 carbon with 230 watts without no problem power adapter.

• Power supply with updated graphics card update

  I am considering buying the HPE-150 t with an improved graphics card standard:

  1 GB ATI Radeon HD 5770 [2 DVI, HDMI, DP, VGA adapter]

  I went on http://support.asus.com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us to the appropriate power needed for this gauge system, and it recommends a minimum 450 Watt power supply.

  If I ended up buying the HPE-150 t with updated graphics card, I get a power supply improved to compensate for the increase of energy consumption?

  
  

  Here are the specs of your motherboard.  It indicates a 350 Watt PSU.  However, if you scroll down to hardware options, you will see a 460 watt power supply associated with the 5770 video card.

• A non programmable power supply with LabVIEW + additional programming hardware

  My company is interested in the use of LabVIEW to automate a non programmable DC power supply. The instrument in question is the U8001A device, but the idea must be the same, regardless of the manufacturer (the instrument was purchased while I was hired, or I would have opted for one with SCPI commands if that's a thing for power supplies):

  http://www.Tequipment.NET/AgilentU8001A.ASP?source=googleshopping&gclid=CMn-rPzAks0CFZM6gQodMu4McQ

  We have two connectors that would be plugged into the power supply and in the 'brick' that holds some sample we want to warm up. This has worked well for our initial target, but we are now interested in time these events alongside 1-2 other instruments that we are exploited (for example a-ohmmeter for quality control), where we can control all this through LabVIEW. Say, only allowing the power reaching the sample at intervals of 5 seconds, with widths of 1-2 seconds impulse.

  I'm sure I'll need a multifunction data acquisition device, and I already have my eyes fixed on the purchase of the NI USB-6501 (link below). My main question is about any additional material which is necesasry, if only a debate of ideas cenceptual on what I'm trying to accomplish. I can do everything I plan only through the acquisition of data, or are there other necessary materials, such as doors? What type of material is suitable for it? I apologize if this is the wrong sub-forum for this topic, as seems to be the subforum of material more appropriate upon publication. Thanks for your time!

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/201630

  Not even an analog command on this power supply... Range of tension and how much power do you need?  You may be able to make an operational amplifier circuit, but find out who can handle that many likely power won't be easy.

  Honestly, I say just to bite the bullet and get a programmable power supply.  It will be cheaper as you try to make a personalized tour to adapt to a peg in a hole square circle.

• How to control the TTi QL564P Power Supply with USB connection?

  Hello

  When I connect the TTi QL564P power supply via the USB port I see not on MAX (peripherals and interfaces) the virtual serial connection. With GPIB, everything works great!

  I already downloaded the latest drivers on the site of the IFG.

  And I created a simple VI like this:

  OPEN--> VISA VISA WRITE ('V1?") --> DELAY (0.1 s)--> READING of VISA--> VISA CLOSE

  (works via GPIB, does not work via USB)

  VISA OPEN I have the name of resource VISA only the LPT1 and COM1 ports available... so where is the USB port (this virtual serial port, case)?

  VISA GPIB resource name is the ALIAS that I set on MAX...

  Thanks for the help

  OK, the solution was... on the front panel of the power supply, I replace the USB bus (I had default GPIB )

• Power supply with Acer Aspire X 1200 problem

  Hello world. I need help. I'm new to Acer Community Forum, but have a problem with my off-warranty X 1200 desktop model. It turns off and I am unable to start it. I changed outlets and also changed the power supply cord. Still nothing. The only thing I see on the Acer Support site is "check the tension on the system setting", but no explanation on how to do this. The system has a fuse that could be replaced? Someone had a similar problem? Any ideas as to what I can do to feed her top? Thank you.

  Ethel

  Thanks for your comments. It turns out that I was able to 'test' the PSU using the method "trombone" (20-24 pin, placing the trombone open between the Green and of the sons of black earth) and confirmed that the most likely guilty was in fact the power supply. I bought a new one on eBay (about $53) and in 2 days it had in my hands. I followed an other UTube on how to replace the power SUPPLY and even if I there was, cleaned dust on the fan, etc., put everything together, and SUCCESS! Now everything works fine. I agree that it would have been probably not cost-effective to have Geek Squad troubleshoot and replace the power supply, but to do it myself, I would say that it was well worth! Considering that it was the first time that I NEVER opened a tour, I feel pretty good on the result. Thanks again for your response! Ethel

• Upgrade to a X 51 power supply with Eurocom Dual 330 Watt power converter

  I recently saw this online converter and thought that it would be possible to use in my 51 R2... x http://www.tomshardware.com/reviews/eurocom-panther-5d-notebook-review, 3685 - 3.html

  made that system only if you read further stated you above. I don't think it will work as its own to this laptop model only.

  By necessity, Panther of Eurocom 5 d has a more robust systems for power supply alternative available on all laptops. His pair of 330 W power supplies convergence through a connector custom to feed the LGA 2011 - flat - desk shape and the GPU W 100 that are attached. Even without overclocking, we saw regularly use exceeding 425 W with peaks of more than 460 W

• Computer won't turn on completely (black screen with blinking cursor) after installing windows updates

  8/7, the following updates have been installed correctly:

  Microsoft .NET Framework 3.5 Service Pack 1 and the .NET Framework 3.5 Family Update (KB951847) x 86

  Update definition for Windows Defender - KB915597 (definition 1.63.1021.0)

  Following this installation, the display resolution has been reset to be very low.  When you try to reset the resolution, I was alerted to a driver problem, so tried installing this in vain (below error code)

  Intel Corporation - display - Intel (r) G33/G31 Express Chipset Family

  Error details: Code 800703E3

  After that, he went to sleep the computer, but was unable to select 'sleep' (it is grayed out) but the stop keys option indicates that the updates were ready to install so I stop thinking which may help.  It was last night.  This morning, the computer was on, seen the screen DELL, then a black screen with flashing white cursor in the upper left corner.  I tried ctrl-alt-del, got the dell screen appears again, then black screen.  I tried ctrl-alt-del, thinking I could try one of the options key F at this time, but he won't even go to this point, the dell blank screen just screen.

  Any ideas would be very appreciated!  It is the second major problem that I had recently after updates vista install (the last time I temporarily lost access to all my files, because they were placed under a temporary user account that had been created!)

  Thank you!

  Hello

  You try to borrow the Vista DVD to any of your friends and do a repair (inplace upgrade) it might help you solve the problem.

  All the best,

  Geek

• Global problems with IE crashing after installing the latest updates from Ms.

  After the installation of the last series MS Updates, we are seeing users get first notification DEP for Windows Explorer (using IE7), then an other error message stating that Windows must close THE Explorer. What happens when users try to access our portal Citrix Presentation Server SSL/VPN.

  Hi Chad t,

  Data Execution Prevention (DEP) is a set of hardware and software technologies that perform additional checks on memory to help prevent malicious code from running on a system.

  The main advantage of the DEP must help prevent the execution of code from data pages. In general, code is not executed by the default heap and the stack. Hardware DEP detects code that is running from these locations and throws an exception when execution occurs. Software DEP can help prevent malicious code to take advantage of exception-handling mechanisms in Windows.

  Microsoft does not recommend to Turn off the Data Execution Prevention (DEP).

  For more information on DEP, you can access the link below for the blog that talks about the DEP and the DEP/NX problems.
  http://msdnrss.thecoderblogs.com/2009/10/10/understanding-depnx/

  As you mentioned it started after the updates, I also suggest you to uninstall Internet Explorer and put it back manually and see if the problem persists. Access the links below for the steps to uninstall and reinstall Internet Explorer 7 respectively.

  http://support.Microsoft.com/kb/927177

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=9AE91EBE-3385-447C-8A30-081805B2F90B&displaylang=en

  For further assistance, you can also consult to Citrix Support to see if they have a fix or a workaround is available.
  http://www.Citrix.com/lang/English/support.asp

  Warning: This response contains a reference to third party World Wide Web site. Microsoft provides this information as a convenience to you. Microsoft does not control these sites and no has not tested any software or information found on these sites; Therefore, Microsoft cannot make any approach to quality, security or the ability of a software or information that are there. There are the dangers inherent in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet.

  Concerning
  Varun j: MICROSOFT SUPPORT
  Visit our Microsoft answers feedback Forum
  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ and tell us what you think
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I have a problem with Windows startup after installing an update.

  Original title: startup problems

  Hello

  As I did the August update, my laptop does not start in normal mode.
  When it starts, it gets to the windows logo, waiting if you like and then the screen flickers and after long hours, I get a 0 000000 x cannot read the message memory.
  I tried the Fix cumputer system recovery, deleated manually updates, nothing works.
  I tried to make a backup, to restart the computer, but you can't do it in safe mode.
  any tips?
  thnx

  of course, you know your stuff.

  It wrked all. It turns out that SXUPTP driver was the problem. updated and now everything works fine.
  Thank you

• Can not run Power saver on my Satellite after installing SP2

  I can't install or run toshiba power saver on my Satellite A60. I've updated to SP2 on the windows update page and cannot run energy-saving. I tried to reinstall the software, but it still doesn't work. Ideas please!

  See you soon
  themalguy

  Hello

  You will find on the site Web of Toshiba Power Saver driver 2.32.0.3C and Power Saver utility 7.03.02. You must install both parties. Note: First the driver that the utility.

  Good bye

• Does anyone know if HP or Microsoft has a fix for the problem with the microphone after installed win 7 own?

  I have a Pavilion 6700 AQuels came with Vista install that the HD has been replaced and installed Win7. Now the built-in microphones do not work on anything whatsoever.  Any help would be greatly appreciated.  Thank you.

  Paul

  Paul Merci much.  You know what I did?  Well, I went to Dev man and looked at the properties of its clicked on update driver card and found a driver Realtec and that fixes the problem.  Works fine now.  Yet once again I can't thank you enough your time a review on this issue.  Don't know if I'll have more questions, but I'll definitely stay here if I do.   ::) Paul