Upgrade memory of PC Compaq Presario SR2177CL Desktop problem

Similar Questions

• wanting to upgrade ram in my compaq presario sr1220nx desktop computer, but mixes information

  I have difficulties to obtain the correct information in the upgrade of ram in my sr1220nx. I currently have 512 MB in a slot and nothing in the other. Is gone to typical products, they said that I can put a maximum of 2 GB (1 GB in each slot). A lot of sites on the net say the same thing. (used their progam Configurator) I downloaded crucial.com scanner who has also verified maximum capacity of 2 GB. I was going to order 2 GB pny brand on amazon.com, but before I did I contacted technical support at the pny site and it said that my computer may not contain total 1 gb (512 in the two slots) he sent me care off hp.com site that has verified this info. I'm a bit at a loss. Thanks for any help. Message attached:

  http://www3.PNY.com/512MB-PC2700-DDR-DIMM-desktop-computer-memory-P1755C30.aspx

  Please contact the Technical Support. No, unfortunately, it's the incorrect memory and sizes. Here are the specs of your system:

  http://bizsupport1.Austin.HP.com/bizsupport/TechSupport/document.jsp?objectID=c00234202&lang=en&cc=u...

  You can only use the PC-2700 (333 mhz) memory, and you can improve only 1 GB (two 512 MB modules). Chances are that you have currently two modules of 256 MB in the system, so you can install both of them and you will hit the max, the system can manage:

  Hey, Dan:

  I use Patriot memory all the time. It should be of low density. Low density is the only way to go.

  Paul

• Upgrade a Compaq Presario SR5710F desktop computer

  Hello, I'm recovering because as far as I can get out my Compaq Presario SR5710F desktop... right now there windows vista service pack 2 32-bit. The processor is an AMD Athlon 64 dual core 4450e to 2.3 GHz with 3 GB of ram at 800 MHz. First of all, since the processor is 64-bit, I was wondering if a windows 7 64 upgrade is recommended... Secondly, I know that even though I have a 64-bit processor, the maximum capacity of ram I have is 4 GB due to the motherboard, but with this card mother, is possible to increase the speed of greater than 800 MHz ram (for the motherboard specifications are hard to find). I was also thinking to replace the graphics card, but what I am seeing that will probably require a different diet and I am on a limited budget. Any suggestion? Please take into consideration the fact that this upgrade is not for games etc, its a home computer that I'm trying to be as updated as possible for a minimal cost. I am realistic, however, and I know it's an old PC. More I am not worried about existing programs (32-bit), I certainly intend on a new installation

  RickCraw,

  Here are the specifications of your Compaq Presario SR5710F desktop computer and its card mother MCP61PM-HM (Iris8). According to the specification, this model has PCIe x 16 graphics card slot and a 250 watt power supply.

  (1) most retail graphics cards require a 300 watts or more big power supply system to work properly. Install a new graphics card to detail will require the replacement of power supply as well.

  (2) Yes, you can install Windows 7 64 bit on this computer. I recommend the upgrade of RAM at a minimum of 4 GB for use with a Windows 64-bit operating system.

  (3) NO, you cannot change the speed of the RAM. Your system is limited to the following specifications/configurations of memory;

  Dual channel memory architecture

  Two connectors DIMM DDR2 240-pin

  Supported DIMM types:

  PC2-4200 (533 MHz)

  PC2-5300 (667 MHz)

  PC2-6400 (800 MHz)

  Memory non - ECC, unbuffered

  Supports DIMM DDR2 2 GB modules

  Supports up to 4 GB (2 x 2 GB = 4 GB)

  Please send Bravo

• Compaq Presario SR1517CL Desktop processor upgrade

  I have a Compaq presario SR1517CL desktop with Asus K8S - motherboard and a Sempron 3000 + 1.8 GHz cpu. Can I switch to a faster processor. If so, that we recommend. I was watching an AMD Sempron 145 2.8 GHz.

  For the salmon in your desktop PC motherboard, go with an Athlon 64. There is a world of difference between Athlon 64 and Sempron processors.  Semprons are in lack of power as consideration for Intel, which is known as a Celeron of treatment.

  

• AMD Athlon II X 95W 3 450 processor compatible with the Compaq Presario CQ5700Y desktop PC?

  I was wondering of the AMD Athlon II X 95W 3 450 processor (ADX450WFGMBOX) compatible with the Compaq Presario CQ5700Y desktop PC? Thank you very much!

  Dr., welcome to the forum.

  Here is the processor upgrades that are compatible with the motherboard:

  • Max TDP: 95W

• Update of Compaq Presario CQ5110Y desktop PC

  I want to upgrade my Compaq Presario CQ5110Y desktop PC then I'll be able to watch TV Online (Football, shows, ect) with crisp clear picture and no gel (if possible, HD quality) I can do this? If so any suggestions on a decent type of video card and power supply upgrades that usually cost an arm and a leg. My video card is now integrated and the provision of my Poweer is 300W. Any help would greatly be appritiated!

  Hello:

  The Sapphire Radeon HD 6450 should work (even if the recommended power supply is 400W) fine.

  The card will draw only a maximum of less than 30 Watts.

  Sound cards... I don't know anything about them, unfortunately, since I have never installed one of my business offices.

• I have a compaq presario sr19090uk desktop pc, and the motherboard was dead. :(

  I have a compaq presario sr19090uk desktop pc running windows 7 64-bit with a card mother micro-ATX (ASUS - A8M2N - LA / Nodus M-GL8E) Socket AM2, Anthlon 64 3500 + socket 939and the motherboard was dead. What is a good replacement that takes in charge a cd/dvd ide burner and sata hard drive for undeer £100. I have also 4 GB DDR2 SDRAM installed.

  Thank you

  Tony

  Here are the specifications of your Compaq Presario SR1909UK desktop and it is card mother A8M2N-(NodusM). There is a conflict in the two specifications for what CPU socket is actually used. The computer specifications claim a socket 939 CPU, while the motherboard plug State she has a socket AM2. You will need to examine your system to confirm what type of CPU and socket he did.

  It can be difficult to locate a market after motherboard that will meet your needs as AM2 socket 939 about 5 years to 8 years and are several obsolete generation. Check e - Bay or similar in your area for a replacement card which meets you the specifications. Please keep in mind is likely to replace the HP OEM Board on your computer Windows become a "non-genuine" and require the purchase of a new operating system. Note that the recovery discs you created will not be also usable on your computer.

• Can connect wireless Compaq Presario SR5214X desktop PC?

  Hello

  I have a Compaq Presario SR5214X desktop PC. Can I connect wirelessly to the network with it? Have you looked online and I refuse to pay support to meet a simple Y / question N can I connect wirelessly to my router?

  Concerning

  Hello

  Your PC does not come with a wireless adapter, but you can certainly install one in a free PCI slot: these are the white horizontal slots shown in the bottom left of your motherboard is an example of the type of card, you need to install on the link below.

  Wireless PCI card

  Kind regards

  DP - K

• Compaq Presario SR1214NX desktop PC: update BIOS for SATA HDD?

  Hi CV Experts.

  In 2004, I bought a HP Compaq Presario SR1214NX desktop PC. Now, leave the original hard drive and I bought a new Seagate 500 GB SATA hard drive. I thought that this would work because the PC MoBo has two SATA connectors. After installation, I noticed the drive is not detected. I checked the BIOS but not hard listed. The installed BIOS is "BIOS Award BIOS Core Version 6.0 revision 3.10 26/07/2004.» What can I do? Is there a BIOS update available?

  Help, please!

  

  Do more research on this issue, I think that this motherboard may not have native support SATA. You can use ports SATA via Windows after you have installed the necessary drivers. I suggest that you add a primary as hard drive IDE PATA drive and load Windows. Post windows installation, install the necessary SATA drivers and plug the secondary drive SATA for use as a hard disk.

  I'm sorry for all of the early confused communications.

• Compaq Presario SR5214x: Replacing the CMOS battery for Compaq Presario SR5214x desktop computer

  How to replace the CMOS battery on a Compaq Presario SR5214x desktop computer. What type of battery? Where is the battery? Thank you (deleted content)

  @ernier

  You will find how to do here.

  http://h10032.www1.HP.com/CTG/manual/c00840496

  REO

• Compaq Presario SR1928IL desktop PC

  I have Compaq Presario SR1928IL desktop PC

  Any v1.0, v1.1 or v2.0 PCIe x 16 graphics card, with the exception of the cards of ATI Radeon HD 54xx, should work on your computer. Keep in mind that the power of your computer's power supply will limit your choice of cards. Depending on the card you get, you may need to replace the power supply.

  Please send Bravo

• Is connected to the Internet, but cannot use the Compaq Presario SR5123WM desktop PC

  Product name & #: Compaq Presario SR5123WM desktop PC (GC660AA-ABA)
  Operating system: Windows Vista Home Premium 32
  No only error message when Internet Explorer does not display the page or iTunes can't find any connection network (any application that requires an Internet connection).

  No changes were made to the system.

  I have the dial-up connection. The Bureau uses the Modem - PCI Soft Data Fax Modem with SmartCP (COM3).

  Once I start the computer, log in to my user and connect to the Internet, I click on Internet Explorer and type in Google to see if it would work. It is said that "Internet Explorer cannot display the webpage". For iTunes, he would say "iTunes has not to connect to the iTunes Store." Make sure your network connection is active and try again. »

  I tried all solutions online and by phone. I reset netsh int ip / winsock. I reset Internet Explorer options. Nothing works.

  What is strange, is that the Internet connection works well on my laptop (using Conexant D110 MDC V.92 Modem (COM3)).

  It would be GREAT if you could help me find a solution to this problem, because this has happened for months, and I'm tired of waiting. I put all my hopes on you.

  You may be able to do a system restore if the original HP partition is always on the computer.

  Here is a document detailing the steps:

  Perform a recovery of the system (Windows Vista) HP

• Compaq Presario CQ5300Y desktop PC - memory upgrade

  Hello, everyone! I hope you are all well.
  
  I have a desktop PC Compaq Presario CQ5300Y, to which I would like to upgrade the memory.
  
  The product specifications indicate clearly that the motherboard, a M2N68-(Narra5), 2 x DDR2 memory media. (In addition, the amount of installed memory is 2 GB.)
  
  The product specifications, in the information section of upgrade memory also mention the following:

  -----------------------------------------------------------------------------

  Dual channel memory architecture
  Supports two DDR2 DIMM (240-pin)

  Supported DIMM types:

  PC2-5300 (667 MHz)
  PC2-6400 (800 MHz)

  Memory non - ECC, unbuffered
  Supports DIMM DDR2 2 GB modules
  Supports up to 4 GB * on 32-bit PCs
  * 32 - bit operating systems cannot resolve a full 4.0 GB memory.

  -----------------------------------------------------------------------------

  I'm clear (with what the article said) I have only available two DIMM DDR2 2 brackets.

  "What confuses me is the statement" ""supports 2 GB DDR2 DIMM '. This is the reason for my question.

  "Supports 2 GB DDR2 DIMM" means that I have to use 2 GB DDR DIMM only, which means I can only go to 4 GB? Or could I use 4GB DDR2 DIMM, which breaks the barrier of 4 GB?

  In a few words, I would like to - at least - 8GB (assuming that I find two modules DIMM DDR2 4 GB). Would it be possible to have the above configuration?
  
  It is important to mention that the PC is running a 64-bit operating system.

  I would appreciate the attention he can draw on this issue.

  Best regards.

  Hello:

  Each slot of memory on the motherboard of your PC cannot accept that a maximum of one module of memory of 2 GB.

  1 x 2 GB will work.

  2 x 2 GB will work.

  1 x 4 GB will not work.

  2 x 4 GB will not work.

• Questions about upgrading a Compaq Presario CQ5205Y desktop computer system

  Good evening

  I'm about to embark on my first serious upgrade of my computer, and I thought it would be a good idea to arrive before I get too far down the rabbit hole (and knocked out my Internet access).  What motivates the need to upgrade, it's that the system tends to lag when I programs using a lot of memory running and I think I can give him a decent boost on reasonably low budget.

  I have a desktop PC Compaq Presario CQ5205Y Win7-64 bit without modification until running.  I'm lookin to upgrade the CPU and the RAM of the machine.  For ease of reference, here is the page describing the system:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=c01859812&lang=en&cc=us&Conte...

  For the CPU, I found a good price on an AMD Phenom X 4 9750 2.4 GHz Quad-Core CPU (HD9750WCJ4BGH).  What I read, it meets the necessary criteria (socket AM2 + 95W, etc.).  I still need to determine if it needs a fan or non - language marketing indicates that it is not), but assuming that it works, here are my questions for this update:

  1 should I update the BIOS on the card, or change one of its parameters to recognize the new chip?

  2. with regard to the installation, I think that it's pretty simple - unlock/remove the Semprom LE-1300 that is there now, carefully align the new processor Phenom X 4 (Golden to golden triangle triangle) and tighten in place. Then, if necessary, install the fan/radiator.  Is this correct, or am I missing something important and potentially catastrophic?

  For the RAM, I have not bought, but I think I need barrettes 2x2gb DDR2 memory unbuffered, non - ECC memory.  I'm showing my ignorance here, but I imagine that rain is better in this case and is much better than the PC2-5300 memory PC2-6400.  If Yes, then maybe something like (or more affordable if I can find it):

  http://www.TigerDirect.com/applications/SearchTools/item-details.asp?EdpNo=6252562&CSID=_61

  Once again, a couple of very similar questions:

  1. do I need to change BIOS settings after I installed memory or if the automatic detection system?

  2. I swapped memory on other computers before so I guess that this motherboard is always the same - unclip/dethrone the existing memory, slide into the new and snap it in place.  Does this sound right?

  In my view, which covers everything I know, but if anyone has any other advice or warning indication, they would certainly be appreciated.

  Thanks in advance for help a beginner brave new waters.

  Processor:

  (1) no updated BIOS available for this model

  (2) more or less correct... you will need a HSF (heatsink & fan) for the new processor and a thermal paste. After the installation of the CPU, you apply the thermal is dedicated to the then install the HSF. The stock will be Sempron HSF to adapt and work but can not dissipate the extra heat

  (3) it is one of these models that will accept AM3 Athlon II and Phenom II CPU (see CPU upgrade in specs), but if it is supported depends on the revision of the motherboard and the BIOS version. Your choice of Phenom 9750 is a sure way to go

  Memory:

  (1) once again, no BIOS update available for this model

  (2) sounds right

  (3) you can look at Newegg.com best prices

  Please send Bravo

• the upgrade of processor in compaq presario cq4010f

  I have a desktop Compaq Presario CQ4010F running Windows 7 Home premium 64 with AMD sempiron chip factory, and I want to improve. I checked page plug product and learned that the motherboard is the manufacturer name: Pegatron M2N68 - LA (5 NARRATED), and HP/Compaq name: NARRA6 GL6. Then I checked the processor upgrade information and learned that it supports the image of socket AM2 + AMD Phenom II chip. I bought the AMD Phenom II X 4 940 3.0 GHz true quad design 8.0 MB total cache chip core. I've installed the chip, and while I was there, I added 1 GB of ram (leading to 3 GB total) just to be on the safe side. When I turned on the computer it tells me "unsupported processor' and turns off. I cursed loudly and ran things. Then I put the old chip in the back and it works fine. I checked the BIOS (the BIOS basic version: 6.0 BIOS revision: 5.54).  The new memory appears, so it's true.  I called a local computer repairman who did work for my mother in the past, and he told me that I have to upgrade the BIOS. I went to HP's download page, but there is no update of the BIOS for my machine. Then, I called 1 800 HP customer/tech support number, but had difficulty in communicating my problem because nobody speaks English as a first language. I cursed even louder and expelled more than things. My cat is still in hiding.

  My question: How can I get this chip to work? I really need to upgrade the BIOS? If Yes, where can I get the said upgrade? If this is not the case, how can I get the current BIOS to recognize the new CPU? How to coax my cat (grey and white tiger striped, 2 years, version 4.5) out of hiding?

  Help, please! I want to play Skyrim.

  Thank you!

  You can post a screenshot of what you mean. ?
  There should not be a difference between the two.

  Computers HP don't require processors HP. The processors are manufactured by AMD and Intel.

  Just compare the specifications of each against what you read in the text of presentation upgrade CPU on the portal of the web HP supported on your motherboard.