USB OTG cable adapter

Similar Questions

• Does not support the Lenovo S650 Usb otg cable

  I bought the new lenovo S650 and I connect the usb otg cable for read my USB but it does not support? Why? Please help me

  S650 hardware does not support the OTG. Regardless of the cable.

  The micro-USB port to charge the phone only.

• Sony EC310 USB OTG cable

  Quick simple question, is the above mentioned cable Z5c compatible?

  Thank you

  It works with Z5 Compact but note that Z5 does not detect a USB device automatically when you plug it in. You must go to the settings-> connection-> connectivity-> USB device USB device detect.

  It also detects USB devices during startup so where the touchscreen does not work, you can plug in a mouse, turn the phone off and then on again.

• Cables USB OTG square

  Doc here with another tip to share!

  Are you worried as me on camera cable, Kit (USB OTG) which sticks to your Xoom, just waiting to be broken? Well, I traveled the four corners of the globe and found a square suitable OTG cable that works just as well without risk of damage. Yes, I tested these cables with the HID devices (keyboard, mouse and a digital camera) and they work perfectly with the Xoom. Unfortunately the portfolio will not close with these cables attached (not enough), but if you have a hole in your case, these keep the dongle or cord next to the Xoom while in the case.

  What's better than a cable of USB OTG left corner you ask? What also get a second USB OTG cables at right angles at the same time? I have provided a few photos below for your viewing pleasure.

  

  

  I used my new found friend USB OTG tonight at Panera Bread sitting in a booth (see photo below), who is much more beautiful than upset with a shot from the upper cable!

  

  Now for the best part, the TWO cables cost me $ 8 on eBay, including shipping (which took 7 days)! For those of you who worry about order on eBay, this seller has good reviews and I had zero problems. BTW, I own the Motorola brand cable as well.

  If you are interested, here is the link:

  http://CGI.eBay.com/WS/eBayISAPI.dll?ViewItem&item=130496350614&ssPageName=STRK:MEWNX:it

  Wish I thought of this cable as my flow Capacitor!

  -Doc

  
  

• Is XOOM MZ605 Brazil supports USB OTG?

  Hello

  Brazil MZ605 XOOM is supports USB OTG, please?

  One of my friends with the Samsung Galaxy S II was able to see my pen drive to my USB OTG cable content, but I am unable to do it with my MZ605 XOOM (3.2 Android or Android 3.1).

  Where Android XOOM MZ605 Brazil 3.1 release notes, please?

  Where the release Android 3.2 to XOOM MZ605 Brazil notes, please?

• Acer Z3 liquid z130 USB OTG

  Question:

  I wanted to know if I can use my phone icw z3 a memorystick. in other words is - what the z3 supports USB OTG?

  If Yes, how can I do this precisely or if that does not work is it possible that I can use USB OTG(on the go) on my z3?

  I already have a USB OTG cable, but it is not acer manufacturing doesn't matter or can I use it if it is possible to

  to do this.

  Friend Ryan

  As much as I KNOW Z3 does not have USB OTG support.

• Xperia Z3 & USB OTG

  Hello

  I have a USB OTG cable I got with my old Nokia N8 I used successfully with my Xperia Z. When I tried to plug this cable even in my Xperia Z3, it doesn't seem appropriate.  And I don't want to force, of course.

  Looking at the two ports close, connectors the Nokia N8 and Xperia Z look similar but the Z3 looks a little closer. From what I can tell on GSM Arena, all three devices claim to have Micro-USB v2.0 ports.

  What happens here?

  Kind regards

  Andries

  I got it by buying a new USB OTG cable.

  Got a labeled as 'Samsung OTG', but the saleswoman nicely I would test in the store and the CAP carries the most diamond shape vs. the more square of Nokia N8/Xperia Z shape

• Course speed SSD at 40 MB/s with USB - C cable

  I recently bought a Samsung T3 USB - C SSD drive for use with my MacBook.

  But right now I am facing a problem of course speed on that:

  I bought it used with my MacBook retina 12' because of the support of USB - C

  But there is a real problem for this drive to use with cable USB - C for USB - C:

  If I use the USB - C to C USB Apple cable, I get only speed USB 2.0 which is capped at 40 MB/s in and out. As the 1-3 photo shows below.

  If I use it with USB - cable USB - A C I USB 3.0 speed of 425 MB/s 400 MB/s on. But the downside part is for MacBook, I use a USB - C for the USB - A adapter as shown in photo 4-6.

  If Apple is any course speed cable USB - C or Samsung should take the blame that send the wrong information of speed USB 2.0 for Macbook?

  Use with direct cable Apple USB - C (I tried another cable USB - C like same problem anker/Chotech) cable is not the problem

  

  You can see that the speed in the information system is listed as USB 2.0 at 480 MB/s

  

  A speed test to confirm it is limited to the USB 2.0 standard:

  

  If I use a USB to adapter USB - C and use the USB - C for cable USB - A on the SSD. It will run at full speed:

  

  You can see that the speed in the information system is listed as USB 3.0 to 5 Gbps

  

  A speed test confirm this works:

  

  The USB - C to C USB cable that comes with the MacBook is not supposed to be used for data, this is to be able to only. You will need to buy a USB - C data cable.

• 2 unrecognized Lenovo A10 - 70F USB OTG tab

  Got cable USB OTG (USB to USB female-A microphone), he joined a key USB Fat32 and hooked up. Immediately detected and offered to always start ES Explorer files for USB OTG. Browsed file on the key, no problem. Then you click on remove. Fix again an hour later, the Tablet does not detect OTG. Test apps OTG confirm that there is no signal OTG. I know it can work, because he did, once, but now there is nothing. Tried to do restart, no difference. If anyone else has experienced this? Any suggestions gratefully received.

  Solved: it was a hardware malfunction... There was a contact folded into the USB port on the cable of the OTG.

• Use of the USB to Ethernet adapter to find cRIO Systems

  Hi all

  I'm trying to connect to one OR cRIO-9066 to my laptop using USB-to-Ethernet adapter.  But I have a problem with it; Find VI systems shows no results unlike the direct connection via the ethernet port on the laptop.  I wish that the connection of the USB-to-Ethernet adapter to support this feature as well.  I would like to know if somebody did, and I hope a solution to this.

  Here's my setup. I bought the adapter USB-to-Ethernet of RadioShack. I connect the adapter to a USB port on my laptop. The adapter is the female Ethernet port on the other end. I directly connect cRIO and the adapter using a crossover ethernet cable. What is of note is that ethernet connection works.  I can specify the IP address of the cRIO then I can communicate with crio in the same configuration. However, finding systems VI cannot find any system.  LabVIEW 2015, is what I use.

  Instead of using the adapter, if I use a direct connection via the ethernet port on the laptop, find systems VI works fine.

  Any help or suggestion is appreciated.

  Thank you in advance.

  After all, my conclusion to this problem has been the model of Ethernet USB card I was using was not good.

  Gigaware USB to adapter Ethernet (from Radio Shack) was working not with find systems VI on my environment even though it is still able to connect to CRIO if I know the IP address. I even had the other, but the result was the same.  The solution for me was to use another model of the BADGE, which is NS-PU98505. It is cheaper, but has worked with find systems VI.

  I don't know what's behind the different behaviour, but the issue is resolved on my end for now.

  Thank you all for all the tips and ideas. Congratulations to all!

• Is rab8 W micro USB OTG?

  Try to get a player to save my SD camera to W rab8 during a trip. All readers say check USB OTG. Does anyone know? Thank you!

  I just use a regular USB cable to connect to windows computers, PC acts as a master. Near as I can tell you need a cable OTG to create another connection master / slave for example to connect two PCs.

  Different load USB and Windows devices, I've seen require USB data lines to be shorted at least momentarily to switch to a full charge to maintenance charge.

• Windows 7 and bios sees not the hard drive, but when I connect the hard drive to the USB with an adapter, I see directories and files

  Please, I need pc

  Original title: windows 7 and bios does not see the hard drive. but when I connect the hard drive to the USB with an adapter, I see directories and files... Ive a hp Pavilion, what to do?

  Check the BIOS for hard drive setting.

  Make sure that you do not connect the drive to a SATA/RAID port.

  Old IDE drives - check the jumper on the drive (use "Cable Select" as a starting point), the BIOS must also be set in legacy/compatibility/IDE mode. Note: If you currently use the AHCI mode, then switch to IDE mode may cause Windows to boot.

  J W Stuart: http://www.pagestart.com

• Can't get USB - IEEE1284 (LPT) adapter/printer installed in Windows 8

  I recently bought a PC in Windows 8.  I have a printer (HP DesignJet 220) with the single port LPT.  I found and installed the printer driver 64 bits for this printer successfully and the printing device (DesignJet 220) shows up in my list of printers.   (Note that I have a HP 1055 all-in-One connected by USB on this machine and it works fine.)

  I bought and installed a USB adapter IEEE 1284 cable and Windows 8 recognizes the adapter (automatically, without having to load a driver).  Problem - when I put the printer port in the window of the printer device to the port of virtual printing USB003, all the instructions I've read - nothing happens.  I tried all USB ports and each port LPT in the list.  Sometimes I print a test page and get an error that the printer's paper (it is not), and sometimes the printer test page is going nowhere - a few stays in the print queue.   The function 'Enable bidirectional Support' is grayed out so I can't activate it (it appears as not controlled).

  The IEEE-1284 device says no printer.  When I try to change the printer driver in the IEEE-1284 device window, he said simply that the driver is up-to-date for the attached device (that he believes is 'none').  The printer is turned on and ready to print.   At any time the printer indicates that it has received all the data (on this model there is a flashing on the control panel when the data is transmitted).

  If I unplug the USB (on the adapter cable) to the computer, it is immediately recognized in the device window and the IEEE-1284 device is removed in the devices window.  If I leave the USB plug in and unplug the Centronics connector at the printer, nothing happens.

  How to make the printing device to connect to the USB port of the virtual printer?  On the other hand, is the problem in the IEEE-1284 device and how to recognize the printer?

  The problem is not the driver.  The problem is the interface.  Eight doesn't seem to work with most LPT drivers.  I tried two so far.  In addition, these interfaces are so old that most manufacturers ceased to provide drivers after Vista.  I tried an interface card (no luck) then a converter USB to LPT.  Eight did not recognize either.  I think the more specific question is if windows 8 supports parallel interfaces.

• USB sync cable

  Help, I lost my USB sync cable and adapter (108-132 VAC/60 Hz, United States)

  for my Palm Tungsten E2, as I looked over the other Forums that back as far as 2005 noone seems to have an answer

  so now that it's 2008, someone had a bit of luck to find this cable?

  Thank you very much, I had no idea that this cable would be so hard to track down...

  Try Amazon.com...

  They're for 0.66 each!

  Amazon Hotsync cable

  WyreNut

  Message relates to: Centro (AT & T)

• My USB to ethernet adapter works only if plugged into my MacBook Pro. I tried to use to start an expander USB (power strip), but this has not--a problem when you have only TWO USB ports ports! Any suggestions?

  My USB to ethernet adapter works only if plugged into my MacBook Pro.

  I tried to use to start an expander USB (power strip), but this has not--a problem when you have only TWO USB ports ports!

  Any suggestions?

  Juice what 'expander' did you use?

  What model of MacBook Pro?

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.