USB port not working do not because of the USB2. 0 - CRW?

Similar Questions

• USB ports not recognized on the computer.

  erased win 8 and reinstalled win 7 ultimate. Now computer will not recognize and usb ports. What should I do?

  I use a Compaq Presario 5320. USB works, that I plug my Saitek yoke and it works correctly. It's only usb drives I plug in I get the message, that he doesn´t recognize...

  TA

  The problem with coming back to win 7 is may or may not win 7 drivers.  I would contact Compaq to see if there is win 7 drivers.

  Another problem if your computer comes with win 8 pre-installed revenant may void the warranty

• HP a6554f: Front USB Ports not working for a6554f

  Hi, I cleaned the dust from my computer yesterday for the first time because the computer kept crashing. I removed the motherboard, so I unplugged everything that was clinging to her and I also removed the hard drive then plugged everything once I had finished, (do not know if I just plugged in as it was, even if I took a video of it, but the wasen can't good quality so I had to guess a little). I also added thermal compound to the cpu.

  Anyway, everyhting seems to work except the 2 usb ports front of the case. It was working fine until I opened the case (this is why I do not open the computers, but the dust was just too). The audio ports and microphone located in the front work correctly. And the rear USB ports are working properly.

  What I've done so far is running pilot Booster and also I went to Device Manager > USB Bus controllers, then I turned off everything on the list, then allowed them again. And nothing has worked.

  I don't know much about computers so I don't want to go to the hassle of opening the case cause once again I was scared lol but could I maybe hooked up a cable in the port of fake?

  Also, is there a diagram to show where each cable goes to the a6554f model?

  As you pointed out the audio before and MIC ports are working, then it might be just the plug for the ports before USB is not properly or is in the wrong place.  Here is a page that relates to the motherboard. In the lower right corner of the image or the page layout scheme, there are two blocks header before normally taken into USB ports.  Says F_USB1 and F_USB2.  Either we must work to the front ports.  Check to make sure that the wiring box beam (which has the wires going to the front USB ports) is connected on one of them.

• One of my USB ports not working

  I have an Asus Zenbook Ux31e. It has a USB port on the left and right. The one on the left has stopped working a few months ago. It does nothing when I plug in my external hard drive, my mouse or my flash drive. Oddly enough, it DOES not work when I plug in my disk drive. The right side works perfectly so I wonder what I can do to solve this problem.

  Here is a picture of Device Manager.

  

  Hi Ams2ay,

  This problem is usually caused due to driver issues or because of material related issues. I would like to know some information about this problem so that we can help you further.

  1. have you made changes on the computer before this problem?

  2. do you get any error code or error message when connecting devices to the USB port?

  3 have you tried the troubleshooting steps to resolve this problem?

  I suggest you try to update the chipset drivers on the Asus or Windows Update site and check if it helps.

  http://Windows.Microsoft.com/en-in/Windows/Update-driver-hardware-ISN

  If the problem persists, then it would be better to contact Asus for further assistance in this matter, because this could be a problem with the hardware.

  Suport of Asus: http://support.asus.com/ServiceHome.aspx?SLanguage=en

  Please reply with the status of the issue so that we can better help you.

• USB ports not working do not. Pavilion dm4-3090se

  USB ports not working do not.

  Thanks for your reply.

  no ports were working, so I went into Device Manager, uninstalled them, re-started... and... iola!

  they were back!

  Thank you again for your answer...

  Louise

• Satellite A200-1tw psae6e - USB ports not working not

  I use windows 7 ultimate on Satellite A200-1tw (psae6e-06u030du) and my usb ports no longer works correctly.
  In fact they recognize certain usb devices, but not all (for mouse and printer example work, but my USB does not work)

  Looking at the Device Manager, everything seems OK... No problem!

  Does anyone have a solution for my problem.

  Thanks :)

  Hello

  Try resetting the USB ports. This means that you need to remove the USB ports/hubs/controllers in Device Manager.
  Then, you have to restart the laptop to get new USB ports.
  In my case it has worked.

  By the way; I recommend upgrading the chipset driver and disable the feature for each energy-saving usb port.
  This can be done in the Device Manager-> port USB-> properties-> tab to save energy

• Equium A60 - 692 USB Ports not working not

  Hi all - new to the forum and what a good place to find info on Toshiba laptops. Anyway - after a recent storm, I lost connection to my ISP broadband - contacted the helpline who advised me to Exchange my ADSL modem to an Ethernet - made and corrected the connection problem - however - only after having it done I realize has none of my devices (printer, camera, Web Cam etc.) worked via the USB ports. I've uninstalled and reinstalled the system and drivers for devices without result. The device displays 500ma of power manager is available for each of the 3 ports but watch 0ma used. The Device Manager also shows that the USB ports are working properly. Can someone help or advise if these ports on a separate card or they are part of the motherboard. If Yes, where can I get a. Congratulations to all - Andy

  A lighting strike is not good news, if she gets hit by a kind something can go wrong. My guess is that your laptop USB ports has taken suddenly by a massive power surge that probably damaged the chips inside. It could be a Windows problem, or not the only thing I could suggest is to use a bootable Linux such as Knoppix CD and run a command called usbview with some USB devices.
  If the USB has been confirmed dead then your only option is to use an adapter CardBus USB 2.0 providing your CardBus slot is not damaged too.

  Richard S.

• 8.1 Windows 64 - bit 3 USB ports not working not

  I have a model computer T430s 2352CTO, running Windows 8.1, 64-bit version. Before upgrading Windows 8.0 all drivers have been updated. The USB ports 3 worked properly, in particular an external hard drive of 1 GB running. After the 8.1 update, 3 USB ports work always, but only for about 30 seconds, then the hard drive stops. The power led remains on the hard drive, but it no longer displays in windows Explorer.

  In Device Manager, I'm gone to Bus USB-> USB controllers Root Hub-> properties-> (under general it says "this device does not work correctly)-> Power Management-> unchecked the box"allow the computer to turn off this device to save energy. Unfortunately, it doesn't seem to stop the problem. Any ideas?

  Please try this:

  http://blogs.msdn.com/b/usbcoreblog/archive/2013/11/01/help-after-installing-Windows-8-1-my-USB-DRIV...

  Thank you!

  Houman

• Pavilion p7 - 1380t: USB ports not working not

  The two front USB ports do work not today. Worked fine yesterday. Everything I plug is not coming. Using ports in the back, they work very well.

  Someone at - it ideas about the problem and a fix?

  Thank you

  Hello @xploded16,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post on how the front USB ports on your desktop computer do not work, and I'd be happy to help you in this case!

  To enable your system to recognize the USB ports before once again, I recommend that you follow the steps described in this document on Troubleshooting connections USB (Windows 7).

  Please re-post with the results of your troubleshooting, and I look forward to your response!
  
  Concerning

• HP Pavilion G6-2146sl: HP Pavilion G6-2146sl left USB ports not working not

  Hi, I have a HP Pavilion G6-2146sl with Windows 7 Ultimate x 64... my problem is that the two left USB ports stopped working properly: for example, when I insert a USB flash drive lights up but it is not recognized by Windows. Is the only port that works on the right side of the laptop. I tried to do a search of driver, but Windows cannot find driver. Here is a screen of my Windows device management:

  

  Thank you in advance for your help and sorry for my bad English, I'm Italian.

  Hello

  AMD AHCI, USB 3.0 chipset and RAID drivers

• USB ports not working not online when using wireless

  Hi, I use windows vista Home premium on a Fujitsu siemens Amilo laptop.

  Until yesterday, I always connected to the internet via a direct connection with my router. Now, however, I have have a direct link and can only connect to the internet through a Wi - Fi

  As soon as I logged online, all my usb ports stop working... I mainly use my mouse and my web cam... the cam sex is essential for my communication with my wife living abroad... Try as I might, I can't get the laptop to recognize any usb... as soon as I'm online... That is to say the internet disconnct, according to my USB again.

  I would be eternally grateful if you could help with this frustrating situation

  Kind regards

  Graham

  Hi CindyThrelkel,

  Try the following steps to resolve the problem:

  Method 1: Run the troubleshooter of material and check what is happening.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: I suggest you perform the clean boot and check.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 3: You can check after uninstalling and reinstalling the USB drivers , if you are able to connect. You can disconnect all USB devices and then perform the following steps:

  a. Click Start and then click Control Panel.

  b. click System and Maintenance, click System and then click on Device Manager.

  Note: If Control Panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  c. in the Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  d. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  If you are still having the same problem then you can check the device USB drivers updated using windows update. See the following help link:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the edge of the question persists I'll ask allows you to check the chipset driver updates you find on the manufacturer's website. The chipset drivers normally integrate USB controller drivers as well.

  You can also check:

  In Windows network connection issues

  http://Windows.Microsoft.com/en-us/Windows/help/network-connection-problems-in-Windows

  Hope this information helps.

• All usb ports not working do not all of a sudden on windows xp

  I have 5 usb ports, which worked very well and all of a sudden none of them work, I checked the status of them in Device Manager and all say working properly?

  Hi Backgammon167,

  The question you have posted is related to Windows XP and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the best support.

  http://www.Microsoft.com/windowsxp/expertzone/newsgroups/reader.mspx?DG=Microsoft.public.WindowsXP.General&lang=en&CR=us

  I hope this information is useful.

  Concerning
  Rehman - support Micrsosoft

• Satellite P10-304: USB Ports not recognize anything

  I have a Satellite P10-304 and the USB ports not recognize anything that are attached to them. Device Manager tells me that they are enbaled and works correctly. What can be wrong with them or what can I do?

  Hello

  One of my friends has the same unit on the work and everything works perfectly. It uses the USB hub too and have many external devices connected to the unit.

  By the way: something like who can occur if the external device is not removed correctly use safely remove hardware option. If you try to connect any other device after that in most cases it is not recognized at all. In this case, you can restart the device or remove ports from the Device Manager and use the hardware detection to find them again.

  Good bye

• When I plug my Galaxy s captivate phone into the usb port on my computer, it will charge the phone but will not allow sharing of information from computer phone.

  Original title: usb with smart phone problem

  When I plug my galaxy s captivate phone into the usb port on my computer, it will charge the phone but I cannot share the news from computer to phone. In fact when I click on the computer icon, it shows the dvd, floppy disks and hard disk but not the phone. I use a mouse usb and headphones and they work fine. I tried to search for devices and it does not work. I run Defender pro anti-virus software and have checked the firewall, but I don't see that his block the phone. I don't know what else to do. Help, please. Thank you

  Hi Mike,.

  Just to follow up with you on that, that very well may be the cause. Especially when it comes to mobile phones, the real cable you use is very important to have all the features when it is plugged into a computer. Where you can try a new USB cable yet, I hope that whoever is completely compatible with this phone.

• USB port not to pick up when it is connected

  USB PORT NOT TO PICK UP WHEN IT IS CONNECTED

  Himanshu salvation,

  ·         How long have you been faced with this problem?

  ·         Did you make any changes before the show?

  Refer to the following Microsoft Fix It solution and click run now , and follow the steps to solve the problem:

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/

  Hope this information helps.