USB Port Replicator II and IEEE1284 - Windows XP

Similar Questions

• USB ports not working not on Windows but works on Ubuntu (fixed)

  Hello

  I have dual boot Windows 8 and 13.04 Ubuntu on my laptop. For some reason, my USB ports doesn't work on Windows, but it still works on Ubuntu.

  I ran a convenience store in the Panel and has detected that there is a problem with my USB (Code 43) ports, but he has not tried to fix or something. Given that my USB ports work fine on Ubuntu, I'm guessing it's a Windows driver issue? I was wondering what I should try to fix this (maybe uninstall drivers and reinstall? how?)
  Would be very happy for any help I could get.
  See you soon!

  Hi Darius,.

  This problem may occur because of the hardware device fails or if the device driver fails.

  Method 1:
  I suggest you try the procedure described in the article and see if it helps.

  Code 43: Windows has stopped this device because it has reported problems
  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = ws.10) .aspx

  Method 2:
  If the problem persists, you can try to download and install the latest USB drivers on the manufacturer's Web site.

  http://support.Toshiba.com/drivers

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• This will work if I plug it into the USB Port of a desktop with Windows 7 HP?

  I had the hard drive of my worn desk w / Vista HP layout box HD Startech. This will work if I plug it into the USB Port of a desktop with Windows 7 HP?

  Hello
  Yes it will work. You can access files on the hard drive but not the Oprating system hard disk previous. The previous hard drive can be used as hard drive.

  I hope this helps.

• No Audio or USB ports with Port Replicator 3 and Portege R600

  I have a problem between my Port Replicator 3 (PA3681E-2PRP) and my Portege R600-13 X (Win7 Pro 32-bit). Everything has been working well for the past few months until a week ago. My PC has developed a problem then that plugged on the Port Replicator, it will not recognize something new that is connected to the USB (two PC & Replicator ones) ports, the Replicator audio output no longer works and the PC hangs during shutdown. Everything is OK with the PC when booted without the Replicator, but as soon as it is connected to the port replicator, in this case.

  I tried looking for information about this problem, but nothing helps... Any help to fix this would be greatly appreciated as it is to set up a business and I need it to work properly.

  A few things to try:

  Reinstall the Toshiba Value Added Package.
  Use system restore to restore Windows to a previous state.
  Check the connector for docking station for damage.
  Back up your data and perform the recovery.

  If its still does not, then I would send the laptop and the Port Replicator Port for an ASP for repair.

• Windows Vista - why my usb ports stopped working, and how do I fix them?

  My 3 usb ports worked very well, but a few days ago they just stop working.  I updated the drivers even though my drivers were already later.  I even tried to update the drivers.  Nothing seems to work.  Can you help me?

  Hi WillisPop,

  ·         Since when are you facing this problem?

  ·         You did it last changes before the show?

  Use Device Manager to disable and re-enable all the USB controllers

  This allows controllers to recover the port USB of his condition does not respond. USB controllers represent the USB ports in Device Manager.

  To disable and re-enable the USB controllers, follow these steps:

  1. click on Start, type Device Manager in the start search box and press ENTER.

  2. expand Universal Serial Bus controllers.

  Note: you may scroll through the list to find this point.

  3. right click on the first USB controller under Bus USB controllersand then click Uninstall to remove it.

  4. repeat the above steps for each controller USB is listed under Bus USB controllers.

  5 restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  6. check the USB device to see if it works.

  You can also check out the article below for more information:

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-in/Windows-Vista/tips-for-solving-problems-with-USB-devices

• Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

  I have a Portege Z30 with 16 GB of Ram, connected to a Toshiba high speed Port Replicator III which is connected to two monitors running in mode extended.

  The monitor attached to the first section of the video is 1920 x 1200 running.
  However the second monitor is only show support for a maximum of 1280 x 1084.

  The monitors are identical, and both are connected by DisplayPort cables.

  I tried to lower the resolution and save the settings on the first monitor to see if it offered options on the second monitor, but the options remained the same.

  At this point, I have narrowed down to 1280 x 1024 so that it conforms to all the monitors but would like to a plus-res solution.

  Does anyone know if there is a fix/work-around for this?
  If this is a hardware limitation, has anyone tried a USB 3 to DisplayPort adapter in a similar configuration?

  Thank you!

  At the same time using two displayports?
  I wonder how it is possible, because of my knowledge it is not possible... as far as I know the Port Replicator III supports two DisplayPorts but you could choose and use one of them...

  In any case, you can use both with a lower resolution, I guess that this problem can be caused due to incompatible display drivers.
  I suggest you to uninstall reinstall or update the display drivers and check if it helps

• Express Port Replicator II and Tecra A10 - 12Z - only the power and LAN

  Since my Toshiba T3600CT I received with docking station, I discovered that I have a docking station. In the meantime, I had a small Sony who had no docking station, for which I got one of the first USB docking station and since then I've seen always to get laptops with docking station.

  But this time something went really wrong, the Toshiba Express Port Replicator II PA3680E-2PRP provides only power and LAN. There is no power in the USB ports, so no serial port or the sound, and DVI and VGA are also disabled.

  All these ports work fine on the Tecra A10, but not on the docking station.

  Of course, it is nice to have the power and LAN, but not when I expected too much of everything.
  So I was wondering if anyone has had a similar problem, it is like upgrading the BIOS for me who have not installed all the necessary software, or is it a fuse or something I could fix myself or is it a faulty docking that shouldn't have left the factory?

  Hello

  What's your Tecra pre-installed with original recovery image?

  When the laptop is preinstalled with recovery image simply connect compatible laptop Toshiba docking station and all the devices connected to the docking station will be recognized correctly and all available ports should work fine.
  Is that a Port Replicator basically "replica" ports on the laptop.

  On this virtual path, we cannot say that this port is 100% OK. What can you say about it? you bought is used a?

• HP Pro 3400 MT (usb ports do not work in windows 8.1 on Intel chipset)

  Are prorts USB on my computer do not work!
  I have Intel (E) 6 series C200 chipset. I'm updating all the drivers and after 5 to 15 minutes when the computer starts, usb ports have stopped working.
  My computer model: HP Pro 3400 MT
  OS: Windows 8.1
  Please, help me! How can I solve this problem?

  Yep! But... If this is not a new installation work? Hmm...

  Without doubt, I find a reason. It's for my X-710-BK (a4tech) mouse drivers. I switch to a different mouse and system now works fine!

  PS > not update drivers just because you can. Updated only if you wish.  -I agree!

• Pavilion 15 laptop n200si: missing USB drivers after formatting and reloading windows 7 on HP Pavilion 15 computer n200si laptop

  I recently formatted my laptop and reloaded windows 7 and lost my 2 left side USB drivers and the drver HDMI. I tried several searches but come back to the top with nothing every time.

  I managed to get the driver for the HDMI, but still nothing on the 2 USB ports.

  in Device Manager, USB 2 ports are yellow! in a triangle. I tried to update the drivers from there and on the HP support assistant.

  the hardware for 1 USB ID is:

  PCI\VEN_8086 & DEV_9C31 & SUBSYS_2163103C & REV_04

  PCI\VEN_8086 & DEV_9C31 & SUBSYS_2163103C

  PCI\VEN_8086 & DEV_9C31 & CC_0C0330

  PCI\VEN_8086 & DEV_9C31 & CC_0C03

  other USB hardware ID is:

  ACPI\HPQ6007

  * HPQ6007

  your help would be greatly appreciated as I need to be able to work with these USB ports and cant gt by just one.

  Thank you and looking forward to the help

  Stuart

  Hello

  The usb 3.0 driver, try the following.

  https://Downloadcenter.Intel.com/download/22824

  The second hardware id is for HP 3D DriveGuard.

  http://ftp.HP.com/pub/SoftPaq/sp71501-72000/sp71811.exe

  Kind regards

  DP - K

• USB ports do not work in windows 7 (64 bit)

  Hello

  recently installed windows 7 on my computer laptop 15-n203tx

  problem is my usb ports work fine in pre installed win 8.1 but now in win 7 port just one works and is the usb 2.0 port and two others are 3.0 and not workng please help me solve this problem!

  Hello:

  You must install this driver usb3.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-127803-1&cc=us&DLC=en&LC=en&OS=4063&product=6521374&sw_lang=

• No USB ports no drivers after reinstalling windows

  Had to re - install windows due to some problems ransomware.  Everything went fine except for the left usb ports drivers, and sm bus controller.  I searched on the HP site for the drivers, but none can be found.  On the right side usb ports are working fine but not the left.  When we look in the Device Manager, they lack drivers.  I tried everything I can think of to solve the problem without success.  Any help would be appreciated.  Thank you

  The machine is

  HP Pavilion dv7-6b57nr

  Hello:

  You must install the drivers for the AMD chipset from the link below that will install the smbus controller and usb controllers 3.

  You want the first file on the Web page.

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064

• USB ports not working is not windows xp worked

  computer works well was closed now rear usb ports and forward does not, said computer drivers work. Help, please

  The other post:

  hub USB root on missing (friendscomputer) program of difficulty need win xp but burn CDs on my computer without it affecting my settings for program win 7?

  have uninstalled and reinstalled the usb ports. found usb root hub missing file. do not know how. the only way I can put a program on my friends computer is with a cd. but can not get the full program without the computer wanting to change my hardware setting, how to get around this please.

  Hello

  You can see the following article for more information on CD burning:

  How to copy music to and from an audio CD in Windows XP

  http://support.Microsoft.com/kb/297015/en-us

   

  How to copy information to a CD in Windows XP

  http://support.Microsoft.com/kb/306524

  I hope this helps.

• USB ports no-opperational in the Windows 7 environment, does not start mode command line safe

  Quick description: experienced difficulty trying to reformat a HD problem. It has been suggested that I have download the diagnosis of the manufacturer. Did. Restarted the computer as required to run the new program. After reboot, no USB port work Windows. Considering that all my USB inputs, it is extremely annoying. Input devices still work on other computers and still work during the start upward (before windows), also does not open in safe mode with the command prompt.

  I tried to reformat a LaCie HD that was previously used for a Mac for PC usage. Gave me a code 43 error and a problem code: 0000002B. Had a bad"block" in the HD somewhere read that I should try to use the manufacturer diagnostic tools to check the HD on.» Downloaded the "LaCie Update Tool" and installed it. It took a reboot. After the reboot, any USB devices worked. (Will begin another thread on the HD as soon as I have this problem.)

  Tried to restart in Mode without failure. Then the Safe Mode with the command of the DVD prompt. (However, I'm not 100% sure that I'm loading from the DVD, I couldn't find a good answer on how to do something so basic.) Always seems to load in the window 7 - always end upwards the newspaper account on screen - certainly no command prompt.

  The keyboard and mouse work on other systems and the keyboard works fine before the Windows 7 screen (the selection of mode that starts in) so I'm pretty sure that it is a Windows 7 problem. Can't really get in the error codes that I can't enter anything now or move the cursor at all. (I'll try to borrow a non-USB keyboard and mouse).

  After a reboot when it asks me what I want to start the computer in safe mode or normal windows 7, loading the drivers, it stops at:

  \windows\system32\DRIVERS\CLASSPNP. SYS

  I don't know if this is normal or the system stuck.

  I tried a manual reset of the motherboard and deleted manually the CMOS on the motherboard did not help - but don't expect really.

  I think I need to run a disk check / fix from the command prompt, but I can't even at the command prompt to the top.

  Thanks to anyone who takes the time to answer, a lot of satisfaction in advance.

  My system:

  Windows 7 64 bit

  ADM Phenom 955 Black Edition Quad

  ASUS 890FXA-UD5

  Microsoft USB wireless keyboard and mouse

  Less relevant stuff: ADATA DDR3 1600 G XPG 2 X 2 GB, Sapphire Radeon 4670 1 GB, Western Digital Caviar Black 640 GB HD, ASUS DVD/CD drive (DRW 24B1st) Corsair TX 750 W

  The Repair Mode command prompt supports USB devices. Here is how you get there:

  1. put your BIOS so that it uses the DVD drive as its primary boot device.
  2 start the computer with your Windows 7 repair CD.
  3. press a button if you are prompted to start from the DVD.
  4. Select repair when prompted.
  5. Select the keyboard language when you are prompted.
  6. When you are prompted, select command prompt.
  In step 2, you can also use the Windows 7 installation DVD. The subsequent steps are similar to those above.

  The process described above is independent of everything that is on your hard drive. If your USB devices still do not work then you probably have a motherboard problem. If it is a desktop computer then you could by a 4 port USB card.

  If you get an account and password for the boot process then you dΘmarrez not from the CD/DVD. I've seen a number of messages in which people reported that they were unable to boot from the CD/DVD drive. Here are the most common reasons for these failures:
  -L' poster neglected the prompt to press a key to boot from the CD/DVD drive.
  -The CD/DVD boot was not a boot disk or was damaged. Use it on another machine has confirmed this.
  -Some BIOS setting was incorrect. Start with some other boot CD/DVD (for example here: http://pogostick.net/~pnh/ntpasswd/) confirmed it.
  -The CD/DVD drive has been damaged or is unable to boot from a boot CD or DVD.
  -The machine has a hardware problem (for example, a motherboard problem) which prevents start in any mode.

• USB ports suddenly freeze and stops working for 10 sec after power off or powered speakers

  Original title: Usb Ports stop working for 10secs after power off or powered speakers!

  Hello

  I have no why, but my usb ports suddenly hangs for 10secs when my speakers turned on or off the power in case of operation of pc... And I have a usb mouse usb wireless keyboard and... with this problem that I can not work properly... and some times my mouse work in early upward and then I should use my keyboard to restart the pc... Then it works very well! Help me please. !

  Hi Thierry,.

  This issue does not appear with Windows that even after you perform a clean installation. So for me, it looks like a material damage. I would recommenmd get you in touch with the manufacturer of your computer and to do the repair.

  Do not hesitate to contact if you have problems with Windows in the future.

• USB ports do not work in Windows 7

  Where my Windows 7 played very well a few weeks ago now, I can't access the USB ports. With a flashdrive in the port, Device Manager it says: 'a driver (service) for this device has been disabled.  Another driver can provide this functionality. (Code 32) ». I uninstalled all programs I had installed in the last 2 weeks so far. Currently, the two pilots showing with a flash drive in the USB port are: disk.sys and partmgr.sys. Could someone guide me how to activate the USB port, I can use a USB Flash drive or even external hard drive USB? Thank you

  You are welcome. Glad to see that worked.