Portege Z30 16 GB with high speed Port Replicator III and two monitors - resolution

Similar Questions

• Tecra Z40-A-176 - how to get support for high speed Port Replicator III?

  Hello

  a customer garage bougt some Tecra Z40 A 176 with high speed Port Replicator III. Unfortunally to either the displayport Port replicators is not working properly and I want to have the support so.

  What I found was the support for laptops page itself, but not for the port replicator.

  With regard to:
  Klaus

  I want to have the support so.

  What do you mean by support and what is the problem with the display port?

  If you have hardware problems, you can contact your dealer or contact the Toshiba authorized service provider that is available in your country.

• Portage Z30-A-13W connected to the high speed Port Replicator III - USB problems

  Hi all.

  We recently bought a new Portage Z30-A-13W and Hi-Speed Port Replicator III.
  Setting network and graphics work correctly with port replicator, but the USB ports don't work at all.

  I tried the port replicator USB 2.0 and USB 3.0 and I can't seem to work with a keyboard, mouse, USB key or a mobile phone.

  In the case of mobile phones, it is also no output power of the ports that the mobile does not start to load.

  At any one another experianced this problem and what was the resolution.

  Thank you very much

  Jonathan Davies

  Hello

  As far as I know additional drivers are not really needed to use the USB ports.
  This is why I m wondering why don t USB ports work.

  It might be possible that ports high speed Port Replicator III USB are faulty, but to be honest, I can't imagine that all 6 USB ports may bad work at the same time.

  So maybe it s a software problem.
  First of all, I would recommend the default BIOS and check the USB legacy support for keyboard and mouse could be activated.
  After access to the Device Manager and remove / delete the USB hubs and controllers in the list of devices.

  Keep high speed Port Replicator III connected to the computer and restart the device.
  Usually, the system should recognize automatically deleted USB ports and must update the drivers of USB ports.

  I hope that the USB ports don't work after this short workaround solution.
  Keep your fingers crossed.

• Toshiba high speed Port Replicator III - use of 2 x 4 k monitors on 60 Hz

  Dear Toshiba support.

  Is it possible to run 2 x 4 monitors k on 60 Hz on the Port Replicator Port Hi-speed Toshiba III (dockingsation)?
  He says he has Display port 1.3 (supports 4 k monitor the 60 Hz.) and a 2.0 HDMI (which also supports monitor k 4 on 60 Hz.).

  With sincere friendships.
  Augurkie

  PauPau wrote in this thread on the high speed Port Replicator III
  https://Forum.Toshiba.EU/showthread.php?83052

  DisplayPort supports the following resolutions:

  Resolution - Refresh Rate (HZ)
  640 x 480 - 60,72,75,85
  720 x 480-85
  800 x 600 - 56,60,72,75,85
  848 x 480-60
  1024 x 768 - 60,70,75,85
  1152 x 864-75
  1280 x 720 - 50,60
  1280 x 768 - 60,75,85
  1280 x 800-60
  1280 x 960 - 60,85
  1280 x 1024 - 60,75,85
  1360 x 768-60
  1366 x 768-60
  1400 x 1050 - 60,75
  1440 x 900 - 60,75,85
  1600 x 1200-60
  1680 x 1050-60
  1920 x 1080 - 24,25,30,50,60
  1920 x 1200-60
  2560 x 1600-60
  3200 x 2000-60

  But it seems the resolution also depends on the GPU built in the notebook

• Driver Toshiba Hi speed Port Replicator III

  Hello.

  I can't find a driver for Toshiba Hi speed Port Replicator III driver on your driver page.

  These need drivers or they are plug-and-play? The port replicator USB ports do not work.

  Thank you.

  I'm not 100% sure but I think you should be able to use all phones compatible with this port replicator.
  What model of laptop do you have?
  Do you use it with the original OS that you got with it?

• Tecra M9 longer works with the Advanced Port Replicator III

  Hello

  I have the Advanced Port Replicator III Plus (PA3474E-1PRP), and it works very well with my M5 (M3 and M200). For example I connect my laptop through it to my monitor/mouse/keyboard/external DVD/hard drives, sound, webcam etc...

  Now, I'm to assess what should I buy as my next laptop and the M9 (PTM91E-03000MEN) seems good.

  Question: * the M9 will work with my plu III advanced port replicator? *

  Otherwise, * y at - it another docking station option that will allow me to connect a M5 and an M9 * please? (of course not at the same time).

  If there is no solution that allows a single docking station for the M5 and M9, then I might as well choose a laptop from another supplier... Main reason to stick to Toshiba all these years is the docking station compatibility that I move older models to the newest...

  All thoughts welcome...

  See you soon
  Daniel
  --

  Tecra M9 and Tecra M5 do not have the same docking connector.
  This means Tecra M5 is the APR III +, Tecra M9 has Express Port Replicator.
  You need the correct docker for each system.

  May it is a solution to be able to use the Toshiba Dynadock. It's USB based:
  http://www.dynadock.com

• Advanced Port Replicator III and Tecra M5 - compatibility issue

  Hi all

  Had a brief search, but could not find a similar position.

  Is the Advanced Port Replicator III PA3314E-1PRP compatible with a laptop Tecra M5?

  Thanks in advance and amicably.

  James

  Yes, it is compatible, I can confirm this info above
  If you wish, you can consult the Web of Toshiba Europe site Options & accessories.
  You will find this info useful

• Tecra A7 with port replicator - the bad external monitor resolution

  Hello

  I have a Tecra A7 (Mod.No. PTA71E) that I use with often an III advanced port replicator and an external 19 "monitor (1280 x 1024).

  Now Ichanged the monitor with a new LCD display 22 '' Samsung 223BW with a resolution of 1680 x 1050.

  Attached to the VGA, I have a lot of flicker problems drinking the reolution is OK.
  Attached to the DVI I have not flickering but the monitor get a resolution of 1280 x 1024 with a desktop computer to 1680 x 1050, that appear depending on the position of the mouse.

  How can I use the DVI and get good resolution (as in VGA mode) but without twinkle?

  Thank you
  Davide Rubbiani

  Hello

  I guess that the Toshiba ATI driver does not support the resolution of 1680 x 1050.
  The only way to get the 1680 x 1050 resolution is to install another driver.

  Maybe here you will find a working one.
  http://drivers.Softpedia.com/get/graphics-board/ATI
  CU

• Problems with an external monitor with the Port Replicator III and M100

  Hey all.

  I just returned from a trip where I took my laptop. Plugged into the Port Replicator port, started and everything was fine. Then after an hour or two, the monitor stopped receiving a signal. I repositioned the laptop and everything was good again. He then loses signal once again, and I was not able to get a signal via the port replicator since.

  The monitor works fine through the hole at the rear of the M100.

  I checked the pins on the Port Replicator port and portable, none folded and tried to clean any dust etc. Still no signal to the monitor.

  Someone has ideas of how to do to solve this problem?

  Jamo

  Hello

  The Toshiba 3 mobile extension is responsible for the good condition of the duplicator 3 market. Try to reinstall this utility and also check the page of the Toshiba driver for updates.

• Portege Z30-A-12N with Port Replicator Port Hi-Speed USB III problems

  Hi all

  I have a big problem with my new Portege Z30-A-12N and Hi-Speed Port Replicator III.

  I connected the power, DVI, LAN, mouse and keyboard to the Port Replicator.
  Power, DVI and LAN are okay, but none will be found if I connect something to the USB Ports 2.0 or 3.0.
  No mouse, no keyboard, and no USB key.

  When I start my Portege I must enter a password after you press the power button.
  These password, I could enter with the external keyboard, but in windows, no keyboard has been found.

  If I connect the keyboard and mouse to the USB Ports of the Portege instead of Port Replicator, the two has been found.

  I ran Windows 7 Enterprise on the Portege.
  BIOS version is 3.30

  Do you have a solution for me?

  Hello

  The HI-SPEED PORT REPLICATOR III PA5116E-1PRP supports 2 x USB 2.0 and 4 x USB 3.0 ports.
  You n t special need Win 7 drivers in order to be able to use the USB ports or other interfaces such as VGA, DVI, audio, etc.

  Sound problems, make sure that the audio device has been selected in the right panel-> sound-> playback tab

  By the way: Win 7 needs USB driver 3.0 which is preinstalled when the laptop was equipped with USB 3.0 ports. My knowledge if your mobile phone does not support USB 3.0, you will be able to use the port replicator USB 3.0 ports.

  Finally and above all devices must be connected before you start the computer. The decision supported and compatible specifications: Portégé R30 - A, Tecra Z40 - A, Tecra Z50 - A, Portégé Z30-A/Z30t-A, Tecra A50 - has

• Need Advanced Port Replicator III drivers for use with my Portege M300

  Hello

  I have a Portege M300 with an Advanced Port Replicator III. I had to reinstall the operating system and now can not find the drivers for the port replicator.

  Can someone help me? I am running Win XP

  Thank you

  Hello

  I guess that you need drivers for the XP operating system. Am I wrong?
  You will find on the page of the Toshiba driver all drivers needed and utilities for Portege M300.
  You will also find the installation instructions document. This document shows the proper installation order.

  You simply download all the drivers and follow the order of installation. All that s

• Port Replicator III + very high CPU when you move the usb mouse only in W2k

  Tecra M2 with a port replicator III +.

  It is set to dual boot XP and Windows 2000 (yes I know it is well a bit but I have a bunch of stuff installed in win2k it is difficult to find these days).

  XP is very good at 100%, but with win 2000 if I use my * USB mouse * on the * ports port replicator and waggle the mouse around - the * CPU * jumps from 0 to * 70 + % * use (System process that seems indicatates like IRQ problem). If I plug the mouse into the ports of the laptop (when the laptop is connected) - it's fine, no more than 5% cpu usage. It's a microsoft basic mouse. I really believe that this is a problem of usb any, because the cpu jumps a little if I type quickly on my usb keyboard (only a few %). It comes with the usb ports on all the Replicator.

  Any ideas? I don't really want to plug my mouse in the morning because it beats a little interest to have a docking station in the first place! I have installed mobile extensions. All other aspects of the replicator are fine

  Martin

  Huh it will not be easy to find the right explanation for this.
  At the moment when Tecra M2 has been offered on the market as Replicator port compatible Toshiba offered Toshiba Advanced Port Replicator III (no +) and at that time both supported in operating system has been tested with it.

  Toshiba later designed Toshiba Advanced Port Replicator III + and confirmed the compatibility with Tecra M2, but obviously with more recent WXP (at this time).
  So now, you've been following situation: you use most recent Replicator port, but with much older operating system so I assume that there may be a compatibility issue with W2K.

  I can't imagine use you so often with W2K and if so, may not be so problematic to connect the mouse directly on the cell s USB port.

  Sorry, but I don't think that there is nothing you can do about it.

• External keyboard works only after the restart with Port Replicator III Plus

  The problem is that when I start the laptop, the external PS/2 keyboard does not work. When I reboot keyboard this one turns around and then I can use it.

  This problem occurs on a laptop Toshiba Tecra with an Advanced Port Replicator III Plus. I used several keyboards, so this isn't the problem. I changed a value in the bios which is used for devices USB (mouse/keyboard). I disabled the option, because I use a keyboard and a PS/2 mouse, but the problem is not resolved. I hope someone has an answer to this problem.

  Hello

  It will be interesting to know what model Tecra you use. Is it perhaps Tecra A6?

• Tecra A8: Problem with the USB printer connected to the Port Replicator III

  Hi all

  I have a problem with my Tecra A8, year Advanced Port Replicator III and a USB printer. With the printer connected to a USB port on the Port Replicator, I have to wait 2 minutes for printing to start. When it is connected directly to a USB port on the laptop and the laptop disconnected from the Port, printing starts immediately. I have the latest drivers from the Isensys of Canon LBP 2900 installed and Windows Vista professional as the operating system.

  I called the technical support of my country, but her is not recorded similar problems.

  A person with similar problem? Some help would be very appreciated.

  Thanks in advance.

  Hello

  Seems like a strange question... Already done the standard procedure in the event of such errors? :)

  The standard procedure is somehow similar to the following:

  -Update your BIOS
  -Update all the drivers for your machine
  -Update your printer drivers
  -Update your operating system

  If all else fails, then try an another Portrep if available, maybe you need to contact your dealer for an another portrep for the test.

  Something like this should be your way. And then you sucessfully made a TROUBLESHOOTIN´ ;)

  I'd be happy to hear feedback from you on your situation...

  Welcome them

• Portege R700: Speed Port Replicator HI + USB Vista questions

  Good afternoon

  I am having trouble with 4-5 new R500-1hd (311th short number), the number could be higher, but users could not have reported it.
  If the laptop is disconnected from the HI Speed Port Replicator 2, it off very well and the laptop can be used, but when the laptop is brought back it does not recognize the mouse or the keyboard. The device does not appear as an "unknown device" in Device Manager, but just does not at all appear.

  A new problem that has arisen is again when the machine is off station USB devices install\work not unless they are connected on port SATA\USB, once again the machine failed to detect at all. Even when devices are picked up, it may take in any case of 30-60 seconds before the work of the mouse and the keyboard.

  These are corporate images deployed through WDS and the problem is very intermittent.
  A reset is applied each time the device will be detected.

  I had a couple of flying machines and finished the stretch prior to the computer with Windows 7, computer image portable devices all work fine with or without the docking station and can be used instantly.

  Isn't anyone has an idea how I can fix this problem?

  Concerning

  Kris

  Hello

  As far as I know speed Port Replicator HI new supports the USB 3.0 standard.
  I found the USB driver on the European driver Toshiba for the USB 3.0 feature page.

  I recommend that you install this!

  Thanks for posting comments after trying that