Use EAP-FAST with ACS 5.2

Similar Questions

• WLC4402, SSC 4.0, EAP FAST with ACS 4.1.23 and Active Directory

  Hi all

  I have a problem where my client software SSC (Cisco Secure Services)-wireless on laptops don't will authenticate the windows domain users if they enter the user name and passwords manually. The unique signature feature will not work. I am using EAP-FAST. It is an ACS appliance based server that I restored from the recovery CD.

  When I look at the failure of authentication request I can see that she is trying to send [email protected] / * / during an attempt to SSO on. The log shows that it is a bad user name or password. Note that the end of the domain name is missing.

  I can see the authentication attempt in the log of the remote agent (CSWINagent.log) on the domain controller, so I don't know that it sends the connection request to the domain controller. The Remote Agent is the same version as the ACS server. When I authenticate successfully (manually) it sends not the domain part of the user.

  This is a new installation. Initially, I had 2 remote agents, both on the service domain controllers has been run under an account with sufficient privileges windows domain administrator. After a planned turn off weekend windows authentication has stopped working completely. I found a post in this forum that says to use the local system to start the remote agent service. This led windows authentication to life, but now I have this problem. I don't know that until I changed it the manual connection is also required in domain (IE user domain\username). I can't be sure that this is the case!

  Can anyone help me to get windows AD to accept these credentials, because they are sent to the client connection? Otherwise if I can make it work with the user account, he worked with initially then that would be great.

  Thank you very much

  As you mentioned that SSC transmits the username "[email protected] / * /" in SSO.

  Is what I think for the moment, to use the feature of Distribution of Proxy on ACS.

  that is, demand to come as it is "[email protected] / * /', let's make ACS Stip off"@domaine"and"username"to RA for AD verification."

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.1/user/NetCfg.html#wp342969

  After stripping '@domaine' send the request back to the ACS it itself, i.e. in the column forward to, ensure that we have input of the ACS.

  And let me know if it works for you?

  Kind regards

  Prem

• Authentication EAP - TLS with ACS 5.2

  Hi all

  I have question on EAP - TLS with ACS 5.2.

  If I want to implement the EAP - TLS with Microsoft CA, how authentication computer and user will be held?

  Understand that the cert is required on the client and the server end, but is this certificate to the computer links or links to individual users?

  If the links to the user, and I have a shared PC connection by few users, is that each user account will have their own certificates?

  And each individual user will have to manually get the CA cert? is there another method that my environment has more than 3000 PCs.

  And also if it binds to the user, any user can get their CA cert with their AD username and password, if they bring in their own device and try to get the CA certificate, they will be able to properly install the cert in their device on the right?

  I hope you guys can help with that. Thank you.

  Hope this will answer most of your questions:

  Client certificate or user

  http://www.Cisco.com/en/us/Partner/Tech/tk59/technologies_tech_note09186a00804b976b.shtml#T10

  Computer certificate

  http://www.Cisco.com/en/us/Partner/Tech/tk59/technologies_tech_note09186a00804b976b.shtml#T15

  In the case of EAP - TLS we have the certificate of computer and user installed on the machines.

  Kind regards

  Jousset

  The rate of useful messages-

• EAP-FAST + new user without certificate

  Hello classmates

  can Yyou you please share a situation with me?

  I ISE 2.0 with certificate based authentication using EAP-FAST. When a new user who never logged on the machine, try to connect... the user certificate does not exist and anyconnect found no valid certificate... and that's my problem.

  I have to allow this user to connect on my PKI and run the GPO update to download the certificate.  is it possible to impllement without any certificate eap-fast authentication? example:-anonymous certificate or self-signed certificate?

  Thank you

  Hello!

  So what you see here is the expected behavior. Your machine is not allowed on the network until it has the appropriate certificates, but you can't get the appropriate certificates until you connect to the network :)

  So, what are your options here:

  1 use the mode of low Impact instead of the closed mode. This allows you to define a pre authorization ACL that grants limited access to new machines so that they can enter all necessary GPO, certificates, etc..

  2. you can configure a rule based only on the computer certificate that allows limited access that will allow the user certificate to be issued. After that, a certificate of authenticity can be started and the user will then authenticate using both the user machine identification information +.

  I hope this helps!

  Thank you for evaluating useful messages!

• For EAP-FAST (inner EAP - TLS) authorization rule

  We have a deployment of ISE, where we seek to use EAP-FAST as our method of inner EAP - TLS authentication method. We check the computer and user certificate. We initially had the following condition in our AuthZ-> EapChainingResult = user and also successful machine rule, but we found that initially succeeded machine and the user fails after windows logon. If we change the condition of EapTunnelType = EAPFAST, then it works fine, logs show that although that initially user fails and machine is successful, after the windows shell login then log message has managed the user and the machine is visible. My preference would be to work with the first requirement, because it is a more valid check but it does not work due to the initial failure, anyone got the EAP-FAST (EAP - TLS) work.

  Concerning

  I have executed him at a client, and you've discovered only machine auth succeeded initially, it's because the user to store where the certificate of users is not open until they have logged ind, this does not work as expected.

  What you can do is to have two different authz, one for eapchainingresult = rules machine succeeded and the user has failed and another when both are successful. This way you can give a granular access by using another for the machine, so the machine does not receive full access to the network before a user is connected.

• EAP chaining with the PEAP Protocol

  I was wondering if we manage EAP chaining with PEAP (not EAP-FAST). For some reason, it does not work for me.

  DS

  I think the answer is 'No', but it is a little more complex than that, because you will use EAP-FAST, EAP-MS-CHAPv2 n EAP - TLS. I have not myself deployed, but here is a link to a good document that describes the process of chaining EAP and requirements:

  http://www.Cisco.com/en/us/solutions/collateral/ns340/ns414/ns742/ns744/docs/howto_80_eapchaining_deployment.PDF

  Thanks for the note!

• 802. 1 x EAP - TLS for wired users with ACS 5.5

  Hi all

  We are setting up a new configuration for wired users authentication with 802.1 x (EAP - TLS). ACS 5.5 we use as an authentication server.

  We have added the certificate (internal) CA root and certifcate for ACS signed by CA. Now, we want to check that authentication works or not. I hope that the CA root and identity certifcate also we need to install in laptop computers. But I don't know how to download the certifcates for client machine manually to CA.

  Please suggest on how to get certificates for clients both manually and automatically?

  Thank you

  Vijay

  Hi Vijay,

  for Wired 802.1 x (EAP - TLS) you must have the following certificates:

  Intermediate server on ACS - Root CA, CA certificate,

  The customer - Root CA, intermediate CA, user certificate (in the case of user authentication) or Machine certificae (in the case of authentication of the computer)

  I do not know what third-party certificate you use, if its Microsoft in the House or any other certificate server, you need to download the client certificate to the server itself.

  In the case of Microsoft, there will be a user certificate template. You can select and create user certificate

  This is an old document, but a computer certificate for the user configuration steps, you can see the steps to download the certificate user if his server from Microsoft:

  http://www.Cisco.com/c/en/us/support/docs/security/secure-access-control...

  In case you use the third serevr certificate, then you must check with them on how to download the certificate of the user

  See you soon

  Mohammed (rate useful message)

• EAP-FAST and the MAC with WPA2 on RADIUS authentication Local for 1242AG access point

  Hello

  Does anyone has a Setup for this combination work?

  Concerning

  VP

  Hi EAP - FAST didn't need any cert... We must generate CAP... Here is the link... that gives the comparison between different EAP

  http://ciscosystems.com/en/us/prod/collateral/wireless/ps5679/ps5861/prod_qas09186a00802030dc_ps4555_Products_Q_and_A_Item.html

  Here is the link to generate or use the CAP

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.3_8_JA/configuration/guide/s38local.html#wp1050270

  Let me know if that helps...

  Concerning

  Surendra

• 7921 EAP - FAST PAC provisioning question (ACS 4.2.0.124.6)

  I'm doing anonymous, CAP of some new 7921 phones with ACS 4.2.0.124.6.

  I created a user & pwd on the phone and add this user to the ACS.

  I have configured the WLC, ACS & phone in accordance with the deployment of 7921 guide (although there are a few options now GBA 4.2).

  When the phone tent first authenticate with ACS, I see failures of connection on ACS for the "anonymous" user I guess it's something to do with the supply of CAP (phase failure 0 etc..).

  But all I see is failures of continuous connection on ACS, and no commissioning CAP occurs.

  Is there maybe another setting I'm missing? Anyone see a similar problem when you try to do this?

  TIA.

  Nigel.

  Here is a screenshot of the wlan

• LEAP and EAP-FAST in the same access point

  Hello...

  We have an infrastructure based on 1142 APs.  Now, they have set up an SSID with JUMP as an authentication mechanism.

  The infrastructure is not a wireless LAN controller, access points are configured as standalone APs with SSID configured in each of them.

  The mechanism to authenticate the windows with JUMP positions was a little tricky.  We need now to migrate all stations to EAP-FAST, but without loss of JUMP environment during the migration.   You have to configure the APs to serve the two authentication mechanism: LEAP and EAP-FAST.

  Is it possible to have it?

  What should we do about it?

  Thanks in advance...

  For autonomous APs. If you are using:

  Authentication open EAP protocol

  Network EAP-

  It accepts virtually all EAP types, not depends on the radius server to have all active... for example EAP methods, if you are using ACS may the PEAP LEAP EAP-FAST, EAP - TLS at the sametime...

  So no matter what, the customer's server and the RADIUS wireless must match the EAP type configured... any type of EAP, the AP should support it...

• Wrong with EAP - TLS with Wireless before Windows logon

  Evil begins with a list of equipment;

  5508 WLC

  3502i AP

  Cisco ACS 5.3

  Clients Windows 7

  WLAN is set up with WPA2 AES with 802. 1 x for key management.

  Customer is set up with WPA2/AES, authentication method is Microsoft: card chip or other certificate on the computer. Authentication mode authentication is the user or computer.  The client is configured to use a certificate on the computer.  "It only works if the authenticating user or computer is seected."  If I use computer authenticate option... it says that it cannot find a certificate to use for the EAP.

  ACS is configured to allow only for the EAP - TLS protocol.

  We have created a stand-alone CA server and distributed CA certificates root and client authentication for all test systems.

  This whole process with EAP - TLS works very well if you are already connected to the machine, with the credentials of the cache.  Once I disconnect the Windows 7 client, I lose the connection to the WLAN.  We want to stay connected to the WIFI network.  W PEAP / MSCHAPV2 works very well with stay connected to the WLAN, but we want to use EAP - TLS.

  Any ideas?

  Thanks in advance,

  Ryan

  Hi Ryan,

  You actually answer your own question :) The reason for the fault is because the computer account doesn't have a certificate, so when your computer account user cannot connect to maintain the session going, and so you are disconnected. Provide the computer with a certificate account and your problem will be solved.

  Richard

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• tried to send emails using the fast-forward button now e-mail flashes on and outside

  tried to send emails using the fast-forward button now e-mail flashes on and outside

  Please disconnect from the Internet temporarily, if necessary, by disabling a Wi - Fi connection or unplug Ethernet cable, whichever is applicable.

  In the Mail menu bar, select

  ▹ Connection Doctor window

  Look for the email account (SMTP) out in the window that opens. Double-click it. Another window opens, displaying the list of all outgoing mail accounts. We'll pick the one affected. Make a note of the settings. Click the sign to remove, and then click OK.

  Reconnect to the Internet and add the account back with the same settings.

• final cut pro could run fast with macBook pro mid 2012?

  My MacBook pro (13-inch, mid-2012). Proc. 2.5 GHz intel Core i5. Memory 16GB 1600 MHz DDR3, startup disk Macintosh HD, 4000 1536 MB video card, could run fast with final cut pro X?

  the specifications of your look familiar to mine... (MacMini2012)

  works like charm IF you use external drives for media...

  recommend as 'work horse' a SSD, usb3 connected, position 250 GB = ~ €120

  very small, very lightweight, blazing fast

• Using the output with 6009 or 6216 possible buffer?

  Hello

  I have a USB6009 and a USB6216. I need to generate a signal by using the analog output and I would use the output buffer. My questions are:

  -The USB6009 has an output buffer? I always get an error, but I know from experience that this device is very limited, so I wonder if they have not only an output buffer... (Programs in input buffer are not a problem at all).

  -J' took the USB6216 and I tried the example WfmGenUp.c downloaded from somewhere in the area of the developer (sorry I lost the link but fix the code) but I am not all analog output signals and after you press ENTER to stop the program (depending on the show) I get this error message:

  NO MORTALS RUN - TIME ERROR: 'WfmGenUp.c', line 113, col 9, id thread 0x0000088C: DAQmxStopTask function: (is-200016 return value [0xfffcf2b0]). Measurements: On-board memory precision passing. Due to the limitations of system and/or the bandwidth of the bus, the driver could not write data to the device fast enough to track the rate of output of the device.  Reduce your sampling rate, change the method of transfer of data (from interruptions on DMA), use a product with more on-board memory or reduce the number of programs that your computer runs simultaneously. Task name: _unnamedTask<0> Code of State:-200016

  I don't know if the problem is just that the 6216 does not support the output buffering or the other...

  -So, if the output control is not supported by 6009 or 6216 what would be the best way to constantly generate signals to 100 s/s?

  Thank you very much

  Kristel

  Hi Ryan,

  the USB-6009 case has 150 s/s softwaretimed AO, so you won´t be able to use AO stamped with the module.

  The USB-6216 supported in the analog output buffer, just follow the recommendations that the driver gives you,

  for example by reducing the sampling frequency, if there is an overflow memory due to the limitations of system and/or the bandwidth of the bus.

  Experiment with the parameters and the basic to see in what range of sampling it works.

  You can find appropriate examples

  ANSI C:

  C:\Dokumente und All Anwendungsdaten Users\Dokumente\National Instruments\NI - DAQ\Beispiele\DAQmx C\Analog Out\Generate Voltage\Cont Gen Volt Wfm - Int Clk ANSI

  LabWindows CVI:

  C:\Dokumente und Users\Dokumente\National Instruments\CVI\samples\DAQmx\Analog Out\Generate Voltage\Cont Gen Volt Wfm - Int Clk Anwendungsdaten All