Use of bandwidth IPSEC 3Des

Similar Questions

• R7500 use of bandwidth by the device and the application does not appear anything.

  Hi, I am currently using a v1 R7500 and since Thursday, I have a problem with the use of bandwidth per device with 0Mbps of traffic for each device.

  

  When I inspect the traffic on the page with chrome I get an infinite number of error at the rate of 1/s.

  

  Does anyone know a fix?

  Factory reset and reflash the firmware

• How to reduce the use of bandwidth LAN?

  I want to design a relay system using two USRP of NI USRP 2922 with sample rates even as LTE standard. But there is limitation in the use of bandwidth of 1 Gbps LAN.

  I don't think you should achieve the full rate on a USRP without a link dedicated to the PC.  The protocol used is UDP between USPR and PC which can be disruped by the latency of the network and cause packets to arrive out of order or get lost.  You should also assume that, due to the effects of edge filter only 80% of the specified bandwidth is usable.  (20 MHz of bandwdith requires a rate of IQ of 25. MECH / s)  It takes a fast PC with a very high quality (we use intel) NIC to get there.  But you will need to use the driver for the NIC card manufactuer and maximize the RX and TX buffers.  So far, I realized only on desktop computers and mobile no.  I also would assume the package of 20% load, so on a 1 Gbps link, I would not expect to exceed the 800 MB/s.

  25 MS/s x (16 bit 16 bit I + q) = 800 MB/s

  You can also, in the pilot, 8-bit mode which will halve your dynamic range, but also the data rate.

  For a system like yours, you can consider to put a PC next to each usrp and install 2 network cards in each PC.  You will add the latency, but the additional computer will give you buffer against congestion and network problems.  In addition, relay is not a 'constant' streaming activity... only the RX is constant.  For TX, you can use the approach of gusts of transmission.

  Erik

• Limit the use of bandwidth per device?

  My father-in-law uses a program that didn't live follow tickers in different stock markets in the world. It takes up bandwidth on our network and does not care if he does or not. It's a real pain, because he will not change his program or get his own connection.

  Is there a method to limit the speed/bandwidth of each system?

  Why not put a QoS rule in place, for this particular device (using IP address or MAC address) and give priority to "low"?

  Allowing him the course "low activity" of others to get optimum bandwidth, and when others are on the same router / network, it will give priority to traffic, via its connection.

  It seems to work at home, where users of League of Legends and Skype (I know who they are :-)) have a low priority, and my work VPN connections have a higher priority)

• Hot to draw what is using internet bandwidth on new Acer V5

  Re: V5-131-2629, Windows 7, nine

  I would like to know what program or process is send and receive megabytes of data on my 3 G connection. My Acer ZG5 (XP) used about 2K bytes of data to get connected to the internet so no more until I loaded web pages. The new Acer V5 immediately sends and receives several megabytes of data to the log on. Also at the time when it is connected but not loading of web pages it will start sending and receiving a lot of MB of data until I log out. It is a problem with my very limited 3G service.

  I use the same Virgin Mobile MC60 (Novatel) USB modem on both computers. It does the same thing with Firefox, Internet Explorer, and Chrome.

  My conclusion is there is a lot of 'services' and also some items in the menu that are send and receive data whenever an internet connection to start is detected, even on a brand new with a single software OEM computer. Together they secretly out a huge amount of bandwidth. This really should make known to the user of Windows 7. I disabled about 20 different services start menu items to take care of this and my sluggish internet connection is much better.

• Use of bandwidth

  I have a WRT160N router on a single wired computer, wireless two computers and a DVD player blue ray with Netflix wireless.  I would like to know my bandwidth to use.  My ISP does not allow access to this information.  Any way to do it at the House of the router?  I am running Win 7 all around.

  It is not possible on Cisco routers.

• use of bandwidth network

  Hi, I use the Java API of Sigar to get CPU load and free memory (in percentages) and there is also a lot of good examples on the sources provided showing this kind of functionality. However, how can I use Sigar to get a similar percentage for the use of the network? It doesn't seem to be an example of how you could get this information. I understand that the metric is not very well defined, but I was thinking something in the sense of the amount of traffic entering and leaving as a percentage of the bandwidth of the Network Interface Card. Windows 7 provides at least one such metric in the Manager of tasks, tab 'Networking' and I was trying to get something similar using Java and Sigar.

  You should take a look at these Java API class:

  NetInterfaceStat

  You can get the values:

  RxBytes

  TxBytes

  Speed

  For a list of the detected interfaces a Sigar object has a method called:

  getNetInterfaceList.

  This allows to detect return of the ETH network, wifi and loop devices. You will need the name of the specific interface OS when getting a reference to the NetInterfaceStat object.

  The tricky part with the use of the network is the implementation of the platform of SIGAR with each operating system. If my memory is correct that Linux has a NOT_IMPLEMENTED indicator set for the interface attribute speed (done in the OS interface layer in the SIGAR C code). I did some experiments under Linux to get this value and its root very intertwind with level permissions to query the hardware. For Windows, you should be fine. For Linux have a way to pass a value configured in your application.

  Good luck.

• API for computer processor Cycles virtual, use of the RAM, use of bandwidth and disk space

  Hello

  Since I'm pretty new to VM Ware, can someone suggest me how to extract the following by a c# application:

  • VM real-time CPU usage

  • VM use of memory in real time

  • VM bandwidth for a session

  • VM allocated disk space and used disk space

  • VM e/s disk operations

  Any help on any of the topics mentioned above is appreciated.

  Also, please let me know the appropriate community if this isn't the appropriate community to write this query.

  Thanks and greetings

  You can find some of the requested data by using the following:

  http://www.VMware.com/support/developer/VC-SDK/visdk25pubs/ReferenceGuide/Vim.VM.GuestInfo.DISKINFO.html

  http://www.VMware.com/support/developer/VC-SDK/visdk25pubs/ReferenceGuide/Vim.VM.RuntimeInfo.html

  http://www.VMware.com/support/developer/VC-SDK/visdk25pubs/ReferenceGuide/Vim.VM.summary.QuickStats.html

  In terms of network and IO usage, it is available, but I don't know where.

  Good starting point is to understand the VI API object model (useful tips, you can ignore the specificities of Perl): http://www.vmware.com/support/developer/viperltoolkit/doc/perl_toolkit_appliance_idx.html

  By poking around the QAnywhere VI guide is also a great place to learn where to find certain things: http://www.vmware.com/support/developer/vc-sdk/visdk25pubs/ReferenceGuide/index.html as well as looking at the CROWD on ESXi/ESX/vCenter is another great place too (http://hostname/mob).

  =========================================================================

  -William

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

• Use a locally swc file to optimize the use of bandwidth for an LMS

  Hello.

  I have an LMS (learning management system), which also uses elements of the virtual world as avatars, games with great graphics etc...

  Bandwidth here in Spain is bad to say the least. Games like world of warcraft ship a CD to put heavy graphics on your local hard drive. It would be a great idea for our e-learning system. Is the best way to use a CFC which is impossible to decompile? It would save a lot of headaches.

  Well, what I'm trying to ask is how can I protect our graphics piracy if installed on the pc local users.

  Thank you in advance.

  You may simply want DRM. Here are some links to check out:

  Documents from Adobe:

  http://help.Adobe.com/en_US/FlashPlatform/reference/ActionScript/3/FLA sh/net/drm/DRMManager.html

  The use of Adobe News:

  http://help.Adobe.com/en_US/AS3/dev/WSe3d2d52902616553-41317b6911d1b4b fb29 - 8000.html

  By the way, the images are data binary just so you can encrypt them with something fast like RC4, use a library, for example:

  https://code.Google.com/p/As3Crypto/

  Ultimately if someone REALLY wants your content, there is no 100% average hackproof. I would implement a reasonable attempt at DRM or encryption, but really measure against the performance hit you'll take to do, with the knowledge that you really cannot guarantee protection in any case.

• Windows updates uses my bandwidth / or Mbps? that is billed by my ISP?

  My updates of the window shows I have several updates that must be installed on my PC - if I leave updates, will be my bandwidth / or Mbps (that I pay my ISP for each month) being exhausted. Windows Updates screen shows some resemble 10.9 MB and so on which is a huge amount!

  Yes, WU downloads are counted by your ISP.

• Setup for use with Cisco Anyconnect VPN IPsec

  So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.

  I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.

  NOTE: We are still testing this ASA and is not in production.

  Any help you can give me is greatly appreciated.

  ASA Version 8.4 (2)

  !

  ASA host name

  domain.com domain name

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  the IP 192.168.0.1 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 50.1.1.225 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  No nameif

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  boot system Disk0: / asa842 - k8.bin

  passive FTP mode

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  !

  permit same-security-traffic intra-interface

  !

  network of the NETWORK_OBJ_192.168.0.224_27 object

  subnet 192.168.0.224 255.255.255.224

  !

  object-group service VPN

  ESP service object

  the purpose of the tcp destination eq ssh service

  the purpose of the tcp destination eq https service

  the purpose of the service udp destination eq 443

  the destination eq isakmp udp service object

  !

  allowed IP extended ip access list a whole

  !

  mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool

  no failover

  failover time-out period - 1

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary

  !

  the object of the LAN network

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1

  Sysopt noproxyarp inside

  Sysopt noproxyarp outdoors

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 proposal ipsec 3DES

  Esp 3des encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES

  Esp aes encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES192

  Protocol esp encryption aes-192

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 AES256 ipsec-proposal

  Protocol esp encryption aes-256

  Esp integrity sha - 1, md5 Protocol

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = ASA

  Configure CRL

  crypto ca server

  Shutdown

  string encryption ca ASDM_TrustPoint0 certificates

  certificate d2c18c4e

  864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105

  0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e

  365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609

  02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109

  6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2

  8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b

  37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c

  234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782

  3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02

  03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1

  cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc

  18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6

  beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef

  af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398

  quit smoking

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 10

  aes-192 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 20

  aes encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 30

  3des encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 40

  the Encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 10

  Console timeout 0

  management-access inside

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2

  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3

  profiles of AnyConnect VPN disk0: / devpn.xml

  AnyConnect enable

  tunnel-group-list activate

  internal VPN group policy

  attributes of VPN group policy

  value of server WINS 50.1.1.17 50.1.1.18

  value of 50.1.1.17 DNS server 50.1.1.18

  Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client

  digitalextremes.com value by default-field

  WebVPN

  value of AnyConnect VPN type user profiles

  always-on-vpn-profile setting

  privilege of xxxxxxxxx encrypted password username administrator 15

  VPN1 xxxxxxxxx encrypted password username

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address (inside) VPNPool pool

  address pool VPNPool

  LOCAL authority-server-group

  Group Policy - by default-VPN

  VPN Tunnel-group webvpn-attributes

  enable VPN group-alias

  Group-tunnel VPN ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  class-map ips

  corresponds to the IP access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the http

  class ips

  IPS inline help

  class class by default

  Statistical accounting of user

  I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)

  Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.

  I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.

  As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)

• iPad, bandwidth use Air

  I wonder if there is a setting or an application that allows you to adjust the use of bandwidth of our wifi at home while other devices will not slow down. I adjusted the applications that run and update in the background. Thank you

  No, there is no adjustment for the bandwidth that uses the device.

• Using the loopback address to identify the IPsec peer

  I have two IOS routers and you want to use the loopback address on the remote router as address such peer recommended in documents such as "Configuration with EIGRP and IPX using GRE Tunneling IPSec."

  On the local router, I identify the remote router via its address and loopback on the remote router, I configure crypto MYMAP map interface S0/0 and BRI1/0 (with nothing configured on the other than the IP address loopback interface)

  When I establish an IPsec tunnel from the remote router, it uses the interface S0/0 as its source address.

  I tried to configure card crypto MYMAP on loopback0 instead of BRI1/0 and S0/0, but it did not work.

  How can I get the remote router to use as source address loopback address?

  Thanks in advance for any help offered.

  Try to use the "crypto-loopback address 0.

  -Dembélé

• 9 use of the bandwidth of Captivate

  Anyone know an easy way to track the use of bandwidth for Captivate courses, or is there a line course Director for how much bandwidth use? We are in an environment in which some areas have very limited bandwidth and cannot play our course, even without audio or video included.

  I am not interested in tips to reduce the size of classes, just some numbers bandwidth usage I can give network administrators. Thank you!

  Have you tried to download on SCORM cloud?

  I think they have performance statistics generated after the course has been viewed which could provide the base you are looking for.

  You should also consider the LMS you use will also have an impact on performance for your users.

  A user at each location could run a 'speed test' to check the upload and download bandwidth they know. This could also be useful to your network administrators to have a conversation with your service provider.

  

• IPsec Site to Site and the question of the IPsec remote access

  Our remote access IPsec 3DES 168 bit encrption has the value

  If we want to allow a remote user to get out of a tunnel to another site must be so 3DES encryption for the Tunnel?

  This tunnel is currently defined by AES.

  If I understand your question the answer is this:

  The VPN client will connect to the ASA with any encryption method, he chose.

  If the VPN client then runs through a tunnel from Site to Site to another location, it uses the encryption method specified in the tunnel from Site to Site.

  This is because as the settings for the client VPN applies only when he puts an end VPN on the ASA.

  When the customer traffic, passes through a different tunnel, the settings for this tunnel applies.

  Hope I answered your question, if not please let me know.

  Federico.