User Guide, integrated into the Web-based software

Similar Questions

• WRT54G V8 cannot connect to the web-based configuration page?

  Earlier, I reset my router and was able to use 192.168.1.1 to visit the configuration page based on the web while trying to restore a home network, now that I have a new computer using Windows 7 that can not use the easylink advisor. I was able to get on the page update my SSID and WEP key. But when my wireless devices were still having problems to you connect to the internet, I tried to go back to the page and found that I can't seem to connect, even if my office is able to connect to other websites very well.

  Anyone know what I can do wrong? I use Verizon DSL. I was able to ping to the router and all tests have shown that it was connected fine, but I still can't get on the configuration page and my laptop can't connect to the network. I tried to reset the router again and still nothing. And Yes, I went through several cycles of power. I have also tried to move if the network card on my computer, but the computer said it was impossible to create a card for him, although at the time I had listed as a home network.

  Wireless on 192.168.1.1 connections often fail.  Using the router configuration pages, always use a computer that is connected to the WRT54G.

  If the above does not solve your problem, so here are my other tips to see the router configuration pages:

  You don't need an Internet connection. 'web Pages' of the router are integrated into the router.
  Use Internet Explorer, it usually works.
  JavaScript must be enabled.
  Use a computer that is connected to the router.
  In the non-working computer, temporarily disable your firewall software.

  Point your browser to 192.168.1.1, and then connect to your router. Your username must be left blank. Your password is "admin" (without the quotes), unless you changed it.

  If you use Zone Alarm, do a right-click on the ZA icon in the taskbar (bottom right of screen) then click on "Shutdown ZoneAlarm" and see if that solves your problem. If this does not work, try the following with Zone Alarm: open the control center ZAISS, go to privacy, then temporarily disable Ad Blocking and Cookie Control and see if it solves your problem.

  Some Zone Alarm users reported that the addition of 192.168.1.1 to their address list "of trust" solved the problem. This trick can also work with other firewalls.

  If you use Noton Internet Security with the add-on Pack, don't forget to disable the blocker and ad blocker. Some users have reported that they needed to uninstall all Norton Add-on Pack.

  If you can not get anything to 192.168.1.1 then perhaps this is not the address of the router. Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig" (with no quotes), and press the Enter key. Look at the "default gateway". It is 192.168.1.1? Point your browser to the 'default gateway', can connect you to your router.

  If the above fails, unplug your modem router, then try again. If it solves your problem, then you probably a "modem-router" rather than a regular modem. A report with this problem and also specify the brand and exact model of your modem (not router) number.

  If all above fails them, turn off your entire system, unplug it from the wall, wait a minute, then lights up, then try again.

  If all the above tips fail, then reset the default router: power down the router and unplug all the wires. Wait a minute. Switch on the router, let it fully boot (1-2 minutes), then press and hold the reset for 30 seconds button, then release the button and allow the router to reset and restart (2-3 minutes). Turn off the router. Wait a minute. To connect to a computer, cable, a router's LAN port. Initialize the system.  The router should work, but you will need to configure your router again from scratch.  If you have saved a router configuration file, DO NOT use it.

  If you still have problems, then you must download and install (or reinstall) the latest firmware for your router. After the update of the firmware, you must reset the default router, and then configure the router again from scratch. If you have saved a router configuration file, DO NOT use it.

• How to access the Web-based utility?

  I have problems to connect to my wireless router, and when I put "admin" (WITHOUT the QUOTES) on the password, the same

  Guest returned three times and after that the message says "'401 authorization required ' (WITHOUT the QUOTES)." I do not understand, I installed the wireless router, just after that I have spend admin and my password (*). Can someone please help?

  My wireless router is

  Wireless-N Router

  Model: WRT160N

  To connect to your router, let the empty user name, then the password, use "admin" (without the quotes).  If you have changed the password of the router connection, use the password that you changed to.  If it does not, the most likely cause is a firewall problem (see information on this below), or you use the wrong password (it may need to reset the router to factory default - more on this below).  Here is my set full of tips for the display of the pages in your router configuration.

  To view the web pages of the router:

  You don't need an Internet connection.  'web Pages' of the router are integrated into the router.
  Use Internet Explorer, it usually works.
  JavaScript must be enabled.
  Use a computer that is connected to the router.
  In the non-working computer, temporarily disable your firewall software.

  If you use Zone Alarm, do a right-click on the ZA icon in the taskbar (bottom right of screen) then click on "Shutdown ZoneAlarm" and see if that solves your problem. If this does not work, try the following with Zone Alarm: open the control center ZAISS, go to privacy, then temporarily disable Ad Blocking and Cookie Control and see if it solves your problem.

  If you use Noton Internet Security with the add-on Pack, don't forget to disable the blocker and ad blocker. Some users have reported that they needed to uninstall all Norton Add-on Pack.

  If you can not get anything to 192.168.1.1 then perhaps this is not the address of the router. Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig" (with no quotes), and press the Enter key. Look at the "default gateway". It is 192.168.1.1? Point your browser to the 'default gateway', can connect you to your router.

  If the above fails, unplug your modem router, then try again. If it solves your problem, then you probably a "modem-router" rather than a regular modem. Check if your modem-router "" uses the same address as your Linksys router 192.168.1.x space. If this is the case, then the report with this problem and also specify the brand and model of your modem router.

  If all above fails them, turn off your entire system, unplug it from the wall, wait a minute, then lights up, then try again.

  If all the above tips fail, then reset the default router: power down the router and unplug all the wires. Wait a minute. Switch on the router, let it fully boot (1-2 minutes), then press and hold the reset for 30 seconds button, then release the button and allow the router to reset and restart (2-3 minutes). Turn off the router. Wait a minute. To connect to a computer, cable, a router's LAN port. Initialize the system. It should work.  Now, your password will be reset to 'admin' (without the quotes).

  If the reset does not fix your system, then you must download and install (or reinstall) the latest firmware for your router. After the update of the firmware, you must reset the default router, and then configure the router again from scratch. If you have saved a router configuration file, DO NOT use it.

• Can I use Google webfonts, or can they be integrated into the Muse?

  Can I use Google webfonts, or can they be integrated into the Muse?

  Would be useful because there are now "optimized" fonts (googlewebfonts) that can be added (embedded?) in a site, while Muse does not offer this possibility.

  Nevermind, I figured it. There may be better ways to do this within the Muse, but it worked for me:

  To http://www.google.com/fonts , I chose a 'test' (Titillium) font family with 11 styles and added to my collection. (This 'collection' will be temporary, since it is only for a single page in Muse). Google web fonts are also FREE.

  Then to the link 'use' Google 11 styles belonging to the family, I chose two weights (200 and 600), each with an extra italic style (200italic and 600italic) - total 4 squares.

  Under 'add this code on your site,' I copied the line of code here and Muse: Page > Page Properties > metadata > "HTML for.""> pasted this code and click OK." You can do a "collection" to Google fonts, or if you're like me and that you change your mind at all times, you can also paste each new piece of code for the fonts to be added below the last one. This can be done globally in Muse; This must be done page by page.

  The part "tricky" for me (do not have updated HTML for a long time as humanly possible), became the HTML syntax that is appropriate for the different weights and styles of 4 fonts I chose of my test font-family.

  After some tests, here's what my guy looks like Muse:

  

  In Muse, here is the HTML code I typed in > object > insert HTML code...:

  

  Note that each HTML tag must be closed in the right place, and Muse, you'll see little ugly 'X-boxes' in your text, which means that something is wrong in the HTML code.

  In Muse, you can change the size of the text box, font size and attack, but not tracking. And if you want to change the text, then 'Edit HTML'.

  I hope this helps others to be used more than able fonts such offers Typekit in the Muse.

• AZ1VR Action Cam Mini with a Wi - Fi connection is the GPS integrated into the handpiece

  I have the new AZ1VR Action Cam Mini with a Wi - Fi is the GPS integrated into the handpiece

  cannellaj wrote:

  I have the new AZ1VR Action Cam Mini with a Wi - Fi is the GPS integrated into the handpiece

  Yes, get the GPS with the AZ1 to remote LVR2V wrist. You must also update the firmware in both devices. I have both and they work great.

• Satellite A110-149 - HPET chip integrated into the southbridge?

  Hello world

  Could not find this information anywhere, so I ask you.
  Don't the Satellite A110-149 has HPET or HPET integrated into the southbridge chip?

  Kind regards
  Charly

  Hello

  It is not known to me, but maybe this info might help you:
  My knowledge of the computer laptop Satellite A110-149 was equipped with processor Intel CELERONM-430 YONAH (1.7 GHZ) and a RC410MD ATI graphics card (ATI Radeon Xpress 200).

  Here are all the details I could find on this device.

• Possible security for the Web-based Configuration

  My colleagues and I found something very interesting today... Despite having configured the FTP security settings (which have been confirmed to set up and in funcitoning. I can't open an FTP session to our remote target without specifying a username admin and the password) If you open the configuration tool based OR web in a browser, you can send via FTP to and from the target using the file remote browser without being connected to all! Everyone knows this?

  Apparently, these permissions are separate from FTP, but you can define these special permissions on the page of the security configuration for the web-based configuration utility.

• Reinstall the Web Cam software

  My web cam software/driver just mysterious disappears from my hard drive and I can't reinstall it unless I have reinstall the OS.  Is there another place I can get a copy of the web cam software and the driver so I can use my built in webcam?  I don't know what triggers it.  I just noticed that is no longer available when I go to the for use and Manager of my web cam says please plug in a supported device.  Any help would be appreciated.

  Hello

  Welcome to the community.

  Visit this link to download and install the Dell Webcam software.

  NOTE from the ADMIN: Broken link has been removed / replaced this post by Dell >

  -Press download and save.

  -Extract the file and run the installer.

  Hope this helps,

• Download VMDK files from the browser to the Web-based data store

  Hello

  I want to download the virtual computer VMDK file using the browser of the Web-based data store. I know how to do, but there is something I don't understand.

  I have configured my VM with a provisioning. From the VI client, I see that the size of the vm.vmdk is 4 GB.  The size of proviosned is 20 GB.

  Technically speaking, if I download the VMDK file, it should be 4 GB, however, from the browser on the vm - flat hard size Web-based data store is 20 GB... What is the standard behavior? Is there a way to download only the actually used 4 GB?

  Hello.

  This is the expected behavior, and as much as I know there is no work around if you use the browser to store data.

  Good luck!

• How to install the basket into the Web of Adobe Muse site?

  How to install the basket into the Web of Adobe Muse site?

  Hello

  Please see the following baskets link

  Kind regards

  Aish

• missing components of the web-based configuration

  Hi all

  I have two controllers cRIO-9074 on my network, both with the OR-RIO 4.0 software installed.  When I open a web browser to display utilities 'OR configuration & monitoring Web-based', a cRIO not show four of the eight tools on the left side of the interface of Silverlight.  Missing the Console Remote File Browser, Web Server Configuration and installed the Configuration Tools.

  I would like for the user of this system be able to download its data files, every day or so using the remote file browser, so this feature would be nice to have. Any ideas?

  Kind regards

  Marvin Perry, DRESSED

  
  

• The Web-based game skill system

  Hi all
  
  I am developing a gambling site based on the web using Coldfusion 8 and MS SQL.
  
  Until recently, things have been going well. But I am now stuck on a small matter to use a system of skills in the game.
  
  The way in which it works (or work), it's that your character in the game will have a large library of skills to choose, which are accessible throughout the entire game. When selecting a skill, your character begins to learn for a while (the time needed for that specific skill). Your character, over time, generates its own library of skills learned - each with him in the game.
  
  I hope this is all clear so far :)
  
  So my small (but actually quite big) problem is that I don't know how to store the list of skills learned.
  My first instinct was to create a column in the table of 'characters' in which the skills learned would be stored in form of list and then stretched when actually listed on a page. But I have heard that the use of lists in the database tables is not a good idea, and usually, I would have preferred another way around the issue.
  My next idea was to create a table that lists all the skills available in the form of columns (a sort of library of every skill in the game), and then the characters have a single line in the table in which they have a 'yes' or 'no' to the title of each column of skills. These answers Yes or no then would be used to generate the library of skills that has character. But this idea is very messy, and I know not even how I could use this table in a SQL query...
  
  I would really like a simple and powerful solution for this problem, and I would be very grateful to anyone who could help me!
  
  Thanks in advance,
  Aiden

  "Thanks a lot for your answer anyway :) and I'm sorry it was not usual.
  for me. »

  Actually Dan was guiding you down the correct database normalization
  path. What you have is a classic many-to-many join. You have a lot
  documents of character and many issues of jurisdiction and that you want to join these
  that a character can have skills 0-N (zero to infinity) and a jurisdiction may
  be used by players 0-N.

  This is done with three tables. An array of characters with the base
  Details of a character and an array of skills with the details of the skills
  and a junction table that links the two. At least join tables
  simple consists of two fields, a foreign key to the characters field
  table and a foreign key of the skills table field. Thus, for each skill
  a character has there will be a record linking the two IDs
  set. Join this table can easily be extended for that other data
  on the join nature of skills such as when he started, what level the
  character has reached in the jurisdiction, regardless of other requirements of your system.

  A simple example:

  Character map
  ID name
  1 Joe
  Sam 2
  3 George

  Skills table
  ID name
  1 hunting
  Cooking 2
  3 archery

  Character_Skill join Table
  CharID SkillID
  1 1
  1 3
  2 2
  1 of 3
  2 S
  3 3

  With basic SQL join syntax allows us to synthesize the data that Joe can
  hunting and shooting arrows, Sam can cook and George can do it all.

  HTH
  Ian

• Linksys spa3102, unable to connect to the web-based utility.

  I have a problem... try to configure my spa3102 voip router, I can't connect you to the basic utility web (192.168.0.1/admin/advanced) page that he asked me to in the installation guide.

  a reapears of error "404-File not found" every time.

  Help, please

  first of all, make sure that your computer is connected to the LAN port on the back of the SPA3102 - then, click Start > run > type cmd > click OK > type ipconfig > hit Enter - glance to the DEFAULT GATEWAY - use to access the web interface of the SPA3102

  ex. If the default gateway as 192.168.1.1 type http://192.168.1.1 in the address bar of your IE - you can then click admin on the upper right of the screen and then click on advanced, also on the upper right of the screen

  * Sometimes the IP address of SPa3102 changes to a different address, especially if the device when you connect the WAN port has the same IP address which is 192.168.0.1

• WRT110-problem accessing the Web-based Setup Page

  I can't access the configuration page based on web for the WRT110 router I have. I am able to make a connection on two computers without the router, but when I add them I get an error message in my browser.

  I tried to access the configuration page based on the web both of my computers and some information were followed by Ecritel.net, but I'm having no luck. I receive the following error message "missed connection: connection to the server was reset while the page is loading." The network link was interrupted for negotiating a connection. Please try again. »

  Any advice would be greatly appreciated! Thank you!

  Actually, I get a different error message now. I made a few adjustments to things like the start menu, which is a problem before. Here is the new error message I received:

  Network timeout Server 192.168.1.1 takes too long to respond. The requested site did not respond to a connection request and the browser has stopped waiting for a response

  Can experience the high demand server or a temporary outage? Try again later.

  Are you unable to navigate to other sites? Check the computer's network connection.

  Is your computer or a network protected by a firewall or proxy? Incorrect settings can interfere with browsing the web.

  Still having trouble? See your network administrator or your Internet service provider for assistance.

  Someone at - it ideas? I searched on the Internet, but nothing I've tried works. Thank you in advance!

• His Dell Inspiron 1420, microphone and camera integrated into the laptop does not work after installing Windows 7 Professional

  No sound from my Dell Inspiron 1420 and the microphone and built-in laptop camera do not work after installing Windows 7 Professional 64-bit. My laptop has Windows 7 Vista 32 - bit family premium. My laptop is 64-bit capable and after going through the Upgrade Advisor, I installed Windows 7 64-bit. I can hear sounds when I use a headset plugged into the line-in Jack, but not through the speakers built into the laptop. I already tried new drivers from the Dell website, but I could not find.

  Any help will be much appreciated. Thank you.

  As it is has no drivers 64 bit Windows 7 on Dell Web site, your best chance is to install the 64-bit versions of Vista (if they exist) in compatibility mode, viz:

  Right click on the Vista driver, then select Properties > Compatibility tab. Now choose to run the program in Vista compatibility mode and then apply > OK. Right click on the file and select run as administrator to install it.