v_workspace model of 2012R2 Windows

Similar Questions

• How to clean the printhead on an HP Photosmart Plus model B210e using Windows 7?

  How to clean the printhead on an HP Photosmart Plus model B210e using Windows 7? I can print in color, but not with the black cartridge, what's new...

  I'm including a document print quality, I'd take a peek at the five solution it will guide you in the process of cleaning print head via the Control Panel on the printer.
  
  Print quality
  
  Let me know how it goes.

• HP Pavilion 17 t J5R51AV: driver for Qualcomm model Atheros QCWB335 Windows 7 (64)

  Hello. I'm looking for a Driver for 7 (64) of Qualcomm Atheros model QCWB335 for Windows. (802.11 b/g/n WLAN and Bluetooth (r) [1 x])

  I tried HP support system discovery and recommended pilot report, he reads material and product incorrect.

  I tried this solution forward to backwards compatibility, but it did not work. http://h30434.www3.HP.com/T5/wireless-Internet-home-networking/driver-for-Qualcomm-Atheros-model-QCW...

  My laptop is a HP Pavilion 17 t (f000?)  P/N: J5R51AV

  I updated the BIOS to F.34

  Windows 7 Ultimate (64)

  Sp67265, sp68433, sp67625 drivers installed and cannot install the sp66402.

  Œuvres Ethernet, WLAN and Bluetooth connection are not.

  The WLAN and bluetooth worked well with Linux Ubuntu 14.04

  History of the laptop

  5 February 2015 ordered from the factory:

  HP Pavilion 17 Windows 7 Professional P/N: J8H36AV t with 802.11 b/g/n WLAN and Bluetooth (r) [1 x]

  Received:

  HP Pavilion 17 Windows 7 Professional P/N: J5R51AV t with 802.11 b/g/n WLAN and Bluetooth (r) [1 x]

  Out of the box, worked very well. I tried to install Ubuntu as a dualboot and discovered, I would need to tweak the installation of Ubuntu to work with 4 partitions that HP had already put in place on the hard drive. Instead, I have supported Windows with Windows backup, created a recovery disk bootable on USB using the HP Recovery Wizard. The Recovery Wizard HP said that the recovery USB disk has been a success.

  I reformatted the hard drive the Sina Active @ killdisk and installed Linux Ubuntu 14.04 successfully. All on the cell worked, including WIFI and Bluetooth. Backup Ubuntu using Ubuntu backup and also created a clone of the hardrive using Clonezilla live 2.3.2.

  Attempted to boot from HP Recovery disk on USB and it failed. Tried again, failed. Contacted HP, they have graciously sent free recovery disks. Only, they sent the recovery disc for Windows 8.1, so I contacted HP and they sent free the recovery disc for Windows 7.

  Recovery disks would work almost throughout the installation of Windows, which gives 3 errors and allowing a Setup log can be fully copied. The errors were "chkErrBB.CMD detects an error during PININST_BBV.", "check c:\system.sav\logs\BurnBootWarn.log." and "check c:\system.sav\logs\BurnBootMerg.log." Analysis the hardrive shows 4 partitions factory HP installs have been installed, the Windows shell folders folders.

  HP support had me has contacted and suggested I send the laptop and pay to install restore it, and instead I bought Windows 7 Ultimate for a clean install.

  Using the HP driver support tools, it indicates the portable bad and suggests drivers for WLAN radio that I have not installed on the motherboard.

  I've updated the BIOS F.34 and which did not help.

  I don't know how to extract the driver from the HP driver and utilities recovery disk HP sent me, it is in a file format that I don't know how to handle.

  I can connect to the internet via the ethernet cable, but not the WLAN.

  Hello:

  See if this driver works...

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_128686_1

  You also need this driver BT...

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_126765_1

• Bluetooth driver wanted for my model 15rt078tu for windows 7 64 bit hp

  I want driver bluetooth for my rt078tu for windows 7 64-bit 15 hp model

  Hello:

  This bluetooth driver should work for you...

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_130390_1

• HP Pavilion 23 All in one - model 23-g010 Windows 7 64 bit - USB and SM Bus controller drivers

  Desperately need drivers Windows 7 64 bit for SM Bus controller and Bus controller series universal (USB).  Looked everywhere, have visited the AMD site and installed the latest chipset drivers, installed what they had on the site driver from hp for the model with Windows 7 64 bit but nothing works.  Thanks in advance!

  Hardware ID-

  USB: PCI\VEN_1022 & DEV_7814 & SUBSYS_2B08103C & REV_01

  Bus SM: PCI\VEN_1022 & DEV_780B & SUBSYS_2B08103C & REV_3A

  Hello:

  Here are the drivers you need:

  SMBus:

  Here's what I did... I have zipped and attached below in attachments, the raw smbus controller driver files to decompress and install manually.

  Download and unzip the file.

  Go to Device Manager and click the controller smbus needing drivers.  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the driver folder that you unzipped.

  Make sure that the include subfolders is selected and the driver should install.  Then restart.

  USB3: Install these two and restart.

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=6943836&SP...

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdDetails/?sp4ts.Oid=6943836&SP...

• Installing the drivers on hp 4441 s (base model) works on windows 7; 32 bit

  I have HP probook 4441 s (base model). I am facing problem in the installation of the base system, bluetooth, USB controller driver, and I also see an unknown device. PL help solve this problem. I am not able to decide which driver will work. Thank you

  What event has occurred which has caused this problem?

  The laptop was delivered in a working state.

  The base system driver is likely to be the JMicron card reader driver.

  All of your specifications required of the drivers for Windows 7 (32 bit) are found here.

  You will have to identify each of the devices by using Device Manager. For each device that is not a driver, right-click on the device in Device Manager and select properties and in the Properties window, select the Details tab, as shown in the following image.

  

  For Bluetooth, the driver is in the network section.

• quilt of old models compatible with windows 7

  We have the old software of couture, boss and duvet. Cannot find any info as to whether it will be compatible with Windows 7 or 8. Get a new laptop and have plenty of models. Help, please.

  Thank you

  Kathie

  For most cases, it will continue to operate perfectly.  However the best way to know is to contact the company that makes it.  Or if you have the name and the version number, you can search online.

• Can't uninstall DisplayLink Core Software on a laptop Sony Vaio (VGN-NR110E model) for a Windows Vista upgrade to Windows 7.

  Hi, I wonder if there is someone who can help me on this issue because it prevents me to install Windows 7 on my laptop.  I have a Sony Vaio VGN-NR110E model, and when I try to install Win7 it tells me that I must first uninstall DisplayLink Core Software.  I went to my control panel to uninstall the program, and it doesn't let me, saying another program he has in use.  On this forum, someone suggested that I'm trying to boot my laptop in safe mode, and it can allows me to remove the program there.  My concern with this would be if I remove this program in Mode safe, how could make sure I'd be able to re - install DisplayLink Core Software should anything go wrong when I try to install Win7?

  The other question I have is there are two other programs that appear to be linked to DisplayLink Core Software.  They are called SONY VGP-UPR1 and there is another utility called program SONY VGP-UPR1 (display Adapater). If I deleted those first, it seems that it can release DisplayLink Core software should be deleted.  In this case someone has already tried that and had success?

  Could someone install Windows 7 on a Sony Vaio VGN-NR110E?

  Hi RC2076,

  Welcome to Windows 7 answers Forum!

  From what I can see SONY VGP-UPR1is a USB docking station for VAIO, try to temporarily disable by right clicking on the program. You can go ahead and uninstall the software basis of DisplayLink, as long as you have the CD for this software.

  Once you are done uninstalling, you can install Windows 7 and later you install DisplayLink Core Software and select then the other two programs that are linked with the above mentioned software.

  You can also run the Upgrade Advisor and check it out. Here is the link to download the Upgrade Advisor.

  http://www.Microsoft.com/Windows/Windows-7/get/Upgrade-Advisor.aspx

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Create a virtual computer model using the Windows Client (c#) function?

  
  The windows-based client can create VM templates?  I created a VM Windows Server 2012 R2 Standard and I would use it as a model for all the virtual machines that follow.  However, I have not yet created the vCenter Server VM but want to use the W2012R2 virtual machine as its base.  I don't see how with the customer I have.  Can if not a model, I simply duplicate the VM?  I don't want to use this machine virtual first for vCenter Server and then create a new one from scratch for use as a model.

  To create templates and clone virtual machines, you will need vcenter server in place, but you can use alternative means to clone this virtual machine to use as a basis for vCenter, take a look at this blog post: cloning a virtual machine without vCenter in ESXi free edition 5.1 | Curiosity killed the cat

• Model number of Windows Server 2012

  Hi all

  So ive downloaded the RTM Server 2012 and built a virtual machine in our environment ESX 5.0 without problem, turned the virtual machine in a model then deployed a machine from this model, but at the start of this new machine, it just sits at the Windows start screen (the part where the windows logo is displayed after the BIOS) and goes no further.  Until this ive left 20 minutes without movement, the small small circle with points going below the logo of windows so its continue to operate in someway and its still using 100% CPU but just not progress.

  Anyone else had any question as a 2012 model?

  Any suggestions for fixing?

  Ta

  Stew

  Looks like the same problem, I had when I first installed a VM with 2012 GTR, which has been set using EFI instead of the regular BIOS (requires reinstall it). Control http://kb.vmware.com/kb/2021887 and perhaps http://kb.vmware.com/kb/2006859 too while you're there.

  I have not tried to deploy as a model still well.

  Anyway, with vSphere 5.1 released tomorrow-ish (and perhaps 5.0 U2?), there might be a fix or two around a few bugs when running in 2012.

  5.0 U1 currently supports 2012/W8 with Support considerations:Tech Preview only.

• Models of VM, Windows and related Clones updates

  In our society, we have a set of VM templates for a variety of different versions of Windows, we need to test our software. Our test workflow goes like this:

  1 Tester creates a new, empty configuration

  2 Tester adds new clone linked VMs for each version of Windows they need to test against, using our models.

  3. tests coming, development challenges coming, more tests, etc.

  4. when the test is finished, VMs will be cancelled but must be kept available for a period of time (several weeks or several months for example)

  Periodically, we run Windows updates on the models to keep them informed. In my view, that it is cancelling publication of the model, deploying, running updates, Undeploying and then publish it again.

  But this raises a few questions:

  We expect problems if not to publish models, run Windows update and then republish these models when there is, linked clone VMs based on them? Through this repeatedly over time will start to degrade the performance of the models (due to new links in chains)? How often, if ever, should we be consolidate models (we prefer to minimize this for reasons of space)?

  In fact, the picture is slightly more complicated, because the models VM themselves are linked clones:

  Windows-> add Visual Studio 6-> add to Visual Studio 2005-> add to Visual Studio 2008-> add to Visual Studio 2010

  Most of our test VMs are linked clones since the last link in the chain above: windows with a variety of pre-installed Visual Studio versions.

  I would be grateful of any advice on 1) how we should address updates of Windows running on the models and the 2) when, if ever, we must consolidate the models.

  Thank you

  Adam

  Periodically, we run Windows updates on the models to keep them informed. In my view, that it is cancelling publication of the model, deploying, running updates, Undeploying and then publish it again.

  Could they remove just the configurations if they're going to be just "sitting there"?  If you want to keep them fresh and current (compared to the model itself), then they should really just remove the configuration and create a new one if necessary.

  We expect problems if not to publish models, run Windows update and then republish these models when there is, linked clone VMs based on them? Through this repeatedly over time will start to degrade the performance of the models (due to new links in chains)? How often, if ever, should we be consolidate models (we prefer to minimize this for reasons of space)?

  I expect questions if you just don't publish/deploy/update / publish.  When "unpublish you" a new link in the chain is done, so any existing VMs based on the previous instance of the virtual machine will continue to exist without error.  All the updates that are placed in a new location, and new virtual machines will be based out of this instance, once you have published it.

  Storage performance can degrade over time, but it really depends on the profile of IO of the virtual machines themselves and the length of the string of this virtual machine.  If the update cycle occurs every month, then perhaps consolidate records each h1/h2.  If you're updating models every week, then maybe do it once per quarter.  It is just the management fees.  The technical limit is 30 links in the chain, but try to keep it under 15 or more.

  (1) how we tackle running Windows updates on the models and 2) while, if ever, we must consolidate the models.

  I think that my comments above should help you out.

  Best regards

  Jon Hemming

• I have a HP Pavilion Entertainment PC, VM2394A #ABC model dv7 - 3060ca Windows 7 Home Premium

  I have picture but no sound when I plug in my cable HDMI to my TV, the sound comes out of my laptop but as soon as I plug in the plug HDMI the sound stops on the laptop and does not come through the TV

  Hello

  Open windows control panel, open Device Manager and open display devices - note equipment listed here i.e. ATI, NVidia or Intel.

  Then connect your laptop via HDMI to your TV.  Do a right-click the speaker icon in the taskbar, and select playback devices.  Once (just to emphasize the entrance), the HDMI output which has the same name as your graphics card, and then click the set as default, see if you now audio left click.

  Kind regards

  DP - K

• Replacing the hard drive HP G62-450SA model / recovery. Windows 7

  Hello

  Last week my laptop started running very slowly, and after a few tests, it seems that the hard drive is on its way.

  I phoned to HP supports, however is out of warranty I wasn't able to get a real support, but advised him to watch the online support pages to back up my files, create a file recovery on a usb device and then it would be as simple as taking on the old hard drive, put in the new, and following the instructions to recover my system and files.

  So after these tips, I've created:

  -A recovery image USB on a Virgin USB key, using the Recovery Manager

  -A backup on an external hard drive using the backup and restore

  -An image of the system by using the backup and restore.

  Then I replaced the hard drive.

  When I turned on the laptop all I get is a black screen that says "no boot device - insert the diskette and press any key".

  I have not all discs. I thought that was the point of creating the recovery image on the USB key? I insert the USB key, and it is not recognized.

  If at this point, I'm stuck. I'm not all boards because HP say they have to charge me.

  Please can anyone here tell me what to do next? What I need to buy recovery discs or is there a way I can install the new hard drive by using the above files?

  Thanks in advance

  Hello

  You are welcome

  Another option, you can try would be to restore the system image you created - you can do the following.

  If you do not, use another PC to create a rescue CD Windows 7.  Download the ISO relevant among the links below.

  Windows 7 32 bit

  Windows 7 64 bit

  You must use an app like ImgBurn ( Note: you can deselect additional software during installation of ImgBurn options) to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.

  When creating, type following the ESC key as soon as you start the launch of the laptop Boot Menu, and then insert the rescue CD.  Select boot options (usually f9 ), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  Connect the drive that contains the system image you have created and then follow method 3 below to reload the image on the new HARD drive.

  http://www.shivaranjan.com/2009/05/21/Windows-7-How-to-restore-Windows-7-partition-or-hard-disk-part...

  Kind regards

  DP - K

• Modeling video in Windows Live Movie Maker

  I was using just Windows Live Movie Maker for editing training videos (add captions, etc.). It's all right, then I struggled to record a video and the next thing I knew that all my videos have been x'd on red. I tried to open the vids in the program (open with) so that first of all, open the program and add the vids. All I see are red Xs. HELP!

  Hello

  In dealing with the problem with Windows Live Movie Maker, I recommend you post your question in Windows Live Solution Center for assistance:

  http://www.windowslivehelp.com/

  Hope the helps of information.

• all of my original games that took on the computer do not work... I tried to play spider solitaire and other zero. model #a6813w using windows vista 64-bit system... Help, please...

  product #nc892aa #aba

  Hello
   
  Could you please answer these money questions?
  1. tell us what happens when you try to open the game?
  2. do you get an error message?
  You can also reinstall the games by turning on the feature of windows. It will install the games.
   
  To enable or disable Windows features, follow these steps:
   
  1. click the Start button, select Control Panel, click programs and then click turn on turn Windows features on or off.
  2. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. to activate a Windows feature, select the check box next to the feature (games). To turn a Windows feature off, clear the check box. Click OK.
  4. After you enable or disable a feature, you may be asked to restart the computer.
   
  Turn on or off Windows features
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-features-on-or-off
   
  Thank you, and in what concerns:
  I. Suuresh Kumar-Microsoft Support.
  Visit our Microsoft answers feedback Forum and let us know what you think.