V3 772g 9653 VGA Windows 10

Go straight to "BOLD" to the question, prior is what led to the question.

I put an mSATA SSD and a clean installed Windows 10 of USB support. To my delight, that I didn't provide a key (made 2 days before the Win 10 free upgrade offer finished) although I used Belarc Advisor for showing it to me until I tried the installation.

Installation was quick and painless and it gave me a start system double managed 8 existing Windows and new Windows 10 (which on the mSATA SSD load in a NICE wink!). I had downloaded a bunch of Windows 10 drivers from the ACER support site before installing Windows 10, but it seemed that I have taken the trouble. I was more worried about the Intel and nVidia installation GTX760, but while I was downloading FireFox, a notification appeared and told me that I had to reboot in order to get all the features of graphics. I had a couple other "must - haves" I wanted before I did the reboot said when another message came to say the same thing, indicating that he had sorted out the nVidia as well as the ifgx. Reboot, which I did.

Everything seemed fine, except that I get "Intel Display Driver for Windows 8 has stopped working and successfully recovered" periodically. Happens if fast, it wasn't a huge deal, as if I were to move a window, there will be a slight delay, then the message, then everything should work perfectly.

In addition, I was dissatisfied with the performance of game under the 760 m. Two racing games, exactly as I had them on my installation of windows 8 was a bit rough on windows 10 and I was wondering if the ifgx was it spoil.

I created a restore point before you install the Intel GFX driver I downloaded from Acer and then run the installation program. Everything went well didn't happen, no improvement in the two games unfortunately. Can't see a driver igfx error but didn't have it going long enough to know for sure.

The problem is that after installing the new driver, the GTX760m does not close at all. The laptop works so much more hot, and I am not happy with that. Because I had done a system restore before updating the igfx I thought that restore would put it right back as it was. No luck. The GTX760M still refuses to turn off the power when you are not using it. When I roll over the icon (which is now always in color instead of being only color when you use), it shows that nothing is to use it. Why then is it not turn off when unused? How can I fix it?

If possible, I got llike to avoid reinstalling Windows 10 from scratch and leaving him to discover again. Any help much appreciated.

Hello

I expect that ), we (the people of the forum) know the struggle with the driver update).

So, do exactly the same thing but a little different

If Device Manager---> Intel hd graphics---> update device software---> browse computer---> here select Let me repeat...---> Click here have disc---> navigate where you have unpacked the driver---> select the graphics file from here---> select the igdlh64.inf and click---> Select the graphics card list intel HD 4600 and click Next. After installation click Close, and then restart.

Please update the graphics drivers from Nvidia as well. And do a clean install if you will be asked.

The point is that Nvidia optimus is responsible for choosing what software use the dGPU and who use the iGPU, so it can also be something wrong there.

I hope that the instructions are not confusing if you have any questions, just ask.

Tags: Acer Laptops

Similar Questions

  • CQ58: HP Compaq CQ58 VGA Windows 7

    Hello

    I recently downgraded my laptop Windows 8 CQ58 for Windows 7 64.

    I tried to connect my projector small office in it and it seems that the VGA port is not active / work.

    There is no missing drivers, that I am aware, I'm now losing this function due to degradation?

    Hello:

    I'm sorry that it didn't work.

    Give this one a try...

    FTP://ftp.HP.com/pub/SoftPaq/sp56501-57000/sp56836.exe

  • Need driver VGA Windows Vista Ultimate 64-Bit for Qosmio G40 - 11 d

    Please, I want to know how to get the driver for Windows Vista 64 - bit for my Qosmio G40 - 11 d because I can not find in Toshiba driver downloads or N-vidia.

    Consult laptopvideo2go (dot) com - they got modded drivers nForce who will probably walk!

  • Acer V3 - 772G - 8.1 Windows, cannot find the boot (like the safe mode) settings

    Hello.

    I can't find a way to access the startup parameters to access the option "Disable driver signature enforcement"

    I used the 2 following ways:

    OPTION 1)

     

    Used a guide from Microsoft (here) and I followed all the steps but I can't find the option.

    Here are the pictures:

    So I don't see no option of troubleshooting... why? Should it not like this: this?

    OPTION 2)


    Power on the laptop, you press ALT + F10 and then follow the steps once you have selected the language and keyboard configuration:

    Where are the startup options? How to start in safe mode? Should it not like this: this?

    Help?

    Thank you

    [Solved]

    (1) open administrator command prompt

    (2) write "bcdedit/set {default} bootmenupolicy legacy" to allow the start of legacy with F8 (don't forget to change the settings after this guide)

    (3) reboot and press F8

    Thanks to Maciej Zalewski of the Acer Support

  • Need Windows 7 display driver for Satellite L20

    Hello, I have problem with the vga on Windows 7 driver I use xp on Windows 7 drivers, but before you install vga driver windows work speed after install driver vga windows slow work and aero does not work.
    I go to control Panel\All Control Panel Items\Troubleshooting\Appearance and customization

    Display after scanning driver is not compatible that's why I use xp with Windows 7 driver.

    I searched on download driver Toshiba L20 drivers but drivers leave L300

    Can you help me to find the driver vga Windows 7? My vga type is intel 915GM/GMS, 910GLM Express Chipset.

    Thanks in advance
    With greetings

    You can't find your laptop model because it is older model and it is listed in the ARCHIVES.
    Under product type choose archive and you'll find it.

    Win7 has nothing to do with WXP so I m wondering how you want to use this old driver.
    If there is a certain similarity between the two operating systems between Win7 and Vista.

    Please remove this driver WXP and try with Vista driver.

  • Windows crash - big blue screen with a sad smily comes then it reboots sometimes

    Hi all, I bought an acer Aspire V3 - 772G with 8 windows pre installed. the thing is while in the middle of something, a blue screen appears just saying that your pc just came across a problem, gives error names such as IRQ_NOT_LESS_OR_EQUAL, look for this error on the internet later... This has been driving nuts me lately. I thought that the problem was with windows 8, so I've upgraded to windows 8.1 but still sometimes. How the hell can I solve this problem? all of the suggestions. What exactly is the problem? any help is appreciated in advance.

    After spending about $ 1,000 on the computer I wasn't expecting this kind of errors.

    Thank you.

    Yes, too common.

    as suggestion, if you are still under warranty, call Acer customer service, probably isn't a hardware issue.

  • CQ62-410US stuck with "Several monitor - Clone View" and VGA port does not

    Hello!

    I have a Compaq CQ62-410US computer laptop with an Intel GMA 4500 M (onboard) video card and a port output VGA, Windows 7 x 64 operating system. A few weeks back the screen was broken (kick straight punch of a child) and nothing could be transmitted via the VGA output either, but the laptop booted and I could hear the sound of Windows 7 logon. I never checked before the VGA output port.
    Yesterday, I replaced the screen broke up with and identical. The fine (full-screen) display in case of back work (boot from USB Flash and the sea + test images), but in Windows 7, two vertical black stripes appeared on the sides because lower than the native resolution. The resolution can be changed at native 1366 x 768 "Screen resolution" because the display is set by default to "Multiple monitors" (I have no other monitor connected, only the built-in screen) and "display of Clone. The built-in display is set as secondary and 'Generic non - PnP' is defined as primary. Any attempt to set the integrated display as primary function or to change the mode "display single" / "Extend view" leads to a black screen with the backlight always on, no matter where I change the settings - in the 'screen Resolution' or 'Graphic properties' (from driver Intel). In the 'Screen Resolution' window the pictogram of the screens show a single screen split in two, and when I press the button "Identify" it shows on the screen ' 1 | 2 ", as you left half of the screen is the main display and half right is the secondary display.
    I put a Philips monitor to the VGA port, Windows detects and installs the appropriate driver, but there is no picture any of mode I put - Clone, Extend, unique display - monitor.
    I tested 3 view of the site of Compaq drivers for my device and the GMA 4500 M drivers from Intel, but the problem is the same (with the drivers from the site intel, on I get only black screen with backlighting.) Pilots are unstable, sometimes at the opening session, page is only a black screen (but before the windows loading screen appear very well) that cannot be changed by "Fn + F4" / "F4" (change view) but a black with the backlight is turned off.
    Due to the replacement of the hard disk, I can't use restore of the operating system that is installed at the factory.
    Please advise me how to solve the display problem and enable the port VGA (get the image on the external monitor).
    Thank you in advance.
    SSM there is not output through the VGA input even at the BIOS screen (no material or to issue independent of the operating system support?).

    I have attached a screenshot.

    Update: I started a live Knoppix CD, and I don't find any problem - unique in 1366 x 768 display configuration; I could even play a game in 3D (OpenGL). While hanging from one monitor to the VGA port, it was found, but when trying to print image to it the OS hung. I guess it's a hardware problem, something to do with the video controller.

    I thought about it, it's the GPU, I think that some of the contacts are damaged. Today even in the BIOS screen I see in the middle of the screen a vertical thin purple line which was bounded two screens on a single screen, and all now have a purple tint.

    I had a quick glance at the GPU and surprise - it is glued to the motherboard, no sleeve, no welding. The motherboard chipset is also stuck.

    See the attached images.

    Thank you for the excellent support. I will never buy anything with Compaq logo on it.

  • Error, input signal is out of range on installing Windows 7

    Hello again, I install Windows 7 on my computer of mothers, but when installing, restart the computer, the screen does not work it says input signal out of range can be dis is because the video card is not a driver, we have a disk with driver say but. Help thanks for all this

    I want to thank you to you all. I solved the problem, I just connect the PC to the TV via a cable VGA windows starts normally and I go to control panel and then to the system and security, then the administrator tools, then the configuration system. When the system configuration window opens I go to the page "boot" and click on "basic video" and then apply the settings and then click on "ok" and I restart the computer. When the computer restarts I unplug the TV and plugged VGA on the monitor cable. I expect windows to load and load successfully when all was fine with the monitor. I change the screen resolution to the highest that my monitor supports. And now everything is fine. Thank you.

  • Display flicker of NVidia and crashed to a black screen on HP IQ500.UK after upgrade of Windows 8

    I have a HP IQ500.UK OS computer original Vista 64 with GeForce 9300 M GS Driver version 174.62. Update of the operating system Windows 8 has replaced the driver NVIDIA version 9.18.13.0286, which is unstable for display, causing frequent display flicker every other second or so, sometimes not get back and goes to black screen. Reboot needed to recover and a phenomenon. The original driver can be deployed in windows 8? HP or Nvidia has a solution? Should I revert to original driver Vista 64?

    Update: I have now the Nvidia driver works and have not had an accident in days. Here's what I did:

    1. You must stop Windows 8 tries to automatically update drivers every time it starts up because that's what's causing all the problems, to do follow this tutorial:
      http://www.c-sharpcorner.com/UploadFile/6cde20/automatically-updates-drivers-in-Windows-8/
    2. Then up to uninstall everything what you have loaded upward and loading the driver VGA Windows options base which is available under find it locally. Do all this in Device Manager
    3. Download the Windows 7 Nvidia driver on the HP support site - don't try Nvidia card who are not compatible
    4. Remove your ethernet cable and/or disable wireless - very important. You'll re-enable it after all this is over, but you do not want Windows to do something unexpected...
    5. Using 7-Zip or some other programs self-extracting unzip the exe that you downloaded. My memory was SP44488 or something like that (I'm at work sorry). Extract it to your desktop or something
    6. Go back into Device Manager, right click on the graphics card and select update or install drivers option.
    7. Select the manual installation option
    8. Select the diskette provided at the bottom of the screen and then go to your exe file extracted in step 4
    9. Windows will look for the name of the driver then install it from there. Your screen, wobbles a bit and you think that its going to crash but mine did not. It takes a while to load so be patient.
    10. Once loaded to reboot the machine. When it restarts it will likely screen black right now that even if you did mine has actually updated the driver to version 9, I think only the first step.
    11. Stop and try again and your father's brother Bob

    I did the above and all my problems disappeared and I have the Nvidia drivers loaded. You'll see the pilot who caused all the problems turn upward in Windows Update as an optional download - INSTALLER DONT IT

    Now, my PC is not the fans screaming as he did when the driver has been disabled and it is much more receptive.

    Hope this helps

    see you soon

    Steve

  • Hello! I have problems with the bluetooth audio

    Hello!

    Help, please! I have problems with the bluetooth, when I use jambox with my laptop for audio streams, the freezing of the computer laptop everything for every 5 seconds. I don't know wat to do...

    I would update the drivers of BT:

    http://us.Acer.com/AC/en/us/content/drivers/4732;-; Longs % 20V3 - 772G

    Select windows as the operating system 8.1

    Check if you have Broadcom or Atheros

  • Display driver stopped responding and has successfully recovered

    Hello

    Yes, I know, there are discussions and topics about this problem here, but I read some of them and none of them helped me to solve my problem.

    CPU: intel i5 750 2.66 GHz

    motherboard: gigabyte p55-usb3

    VGA: sapphire radeon hd5850 toxic

    RAM: geil 2 * 2 GB ddr3 1333

    Ok. When I go to apply 3d in win 7 64 bit, after a few minutes, the screen freezes and the program crashes and I get this:

    «"" driver AMD display driver stopped responding and has successfully recovered.»»» » »

    I had this soccer10, assassins creed 2, crysis warhead, benchmark of sky, nba 2 k 10, etc.

    things, I did and did not help: I reinstalled programs, reinstalled windows, all drivers updated, update the bios of the motherboard and vga, windows update, checked the hardware, cooling systems, etc...

    I know it seems like a hardware problem, but since I don't get it in win XP, I think it's a windows problem. See, I played assassins creed 2 on higher graphics options (60 fps) for many hours, I have same finieshed crysis warhead with keen twice under XP. No problem.

    but in win7, I always have this error even in circles low, and when the vga is 40 to 50 degrees Celsius.

    Thank you

    Hello

    Check with Sapphire Support and Forums (for the known issues and solutions) and drivers.

    Sapphire - Support
    http://www.sapphiretech.com/presentation/support/?PSN=0002

    Sapphire - drivers
    http://www.sapphiretech.com/presentation/downloads/download_index_01.aspx?PSN=0006

    Sapphire - communities and more
    http://www.sapphiretech.com/presentation/Member/member_index.aspx

    ==============================================

    Try this even if you did similar before.

    Download the latest version of the driver, but DO NOT install it again.

    Start in Safe Mode - press F8 several times.

    Panel - Manager of devices - graphics cards - click on - UNINSTALL - check of control
    REMOVE DRIVERS

    RESET

    Now go to where you put the drivers and click right on - RUN AS ADMIN.

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • Helping to create crashing after you import a video clip

    Hello

    I'm a first time of first user, but failed to start my first still.

    I can open the first, but when I try to import a video clip and click on it (or try to drag on a sequence), the program crashes with the following message:

    "Adobe first Pro CC 2014.2 stopped working: a problem caused blocking the program works correctly." "Windows will close the program and notify you if solutions are available.

    I tried a number of things to resolve, but the only chance I had uninstalled my graphics driver which then he solves the fracas, however only has then supported VGA Windows Basic.

    The system key information:

    First Version = Adobe® first® Pro CC v8.1, caravan, version 2014.2, build 8.2.0 (65)

    Operating system = Windows 7 Home Premium, Service Pack 1, 64-bit, Version 6.1, Build 7601

    Material = Intel® Core™ i5 - 4570S CPU, integrated Intel® HD Graphics 4600 (Driver version 10.18.10.3960), 8 GB of Ram.

    This problem occurs with or without the GPU of Mercury Playback Engine acceleration.

    I also tried to close the preview window before you click any clip, which seems to slightly delay the crash until the preview window automatically opens again.

    Has anyone previously met, or have pearls of wisdom?

    Thank you

    Vicky

    I ended up installing a separate certified GPU that solved the problem.

  • Please I havea problem with my driver vga with windows 8

    I tried several times to install windows 8, but the problem always come with driver vga. my laptop is pavilion dv6-6b90se

    Please give me help

    Hello

    Please check the following link, there driver Windows 8 now but don't update in the next few days:

    http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?swlinkmsg=100 & CC = US & DLC = in & docname = c00042629 & lang = to & LC = in & Product = 5204551 & Tool =

    Kind regards.

  • Satellite L655-13U and detection of windows VGA max

    My laptop is Toshiba Satellite L655-13U and vga card does not Max the windows to detect 64-bit only from 1654
    I want to be the vga is max how?

    Hey Buddy

    Sorry, but your ad is quite understandable.
    Be so kind and try to explain it with other words.

    What is the problem with your laptop? Maybe display resolution?

  • Z40-70 windows 7 (32 bit) Intel VGA driver support downloads page does not work

    Hi people,

    just got a 59436180 Z40 - 70 w / nvidia geforce and installed with windows 7 (32 bit).

    installing the nvidia vga drivers told me I need to install intel vga driver before installing the nvidia, one card...

    the problem is that I can't install the driver vga intel that I got the support of the lenovo download page (the name of the file is 'ivg200w732.exe'),

    When I run it, it says something like my computer doesn't have the minimum requirements for the driver to install...

    Well it seems that it is the wrong driver, because when I explore the installation directory, I found a 'x 64' - named directory... and not "x 86" or "32 bit" or something similar... "."

    someone has the same problem?

    Help...

    had the driver from the site of intel... resolved.

Maybe you are looking for