Valet - NAT or SPI service?
The Cisco Valet/Valet Plus there technology of network address translation (NAT) or a firewall SPI? (Or both?) Thank you.
Both.
Tags: Linksys Products
Similar Questions
-
Networks VPN NAT l2l problem-Dup-HELP!
I use a router IOS as a VPN L2L device to connect my site to several different customer locations, some of them use the same internal IP addresses. These VPNS have been working well.
I recently added another client to this system and I am now having a problem with the new configuration. With this configuration, I have NAT my internal addresses. NAT works correctly, but it NAT my bad common NAT addresses and therefore do not generate the tunnel.
My internal IP 10.10.x.x
incorrect NAT pool 10.129.x.x
decent NAT pool 10.99.x.x
Help... :))
Thank you
The problem is simple. You have almost an identical ACL for two guests. As the first NAT rule has been added previously, it comes into play. To resolve this issue, you must set explicit host/subnet destination match instead of 'none' keyword.
For example like this:
ip access-list extended ME-CRYPTO-ACL
permit ip 10.129.40.0 0.0.0.255 host 10.10.131.63
ip access-list extended ME-NAT-ACL
permit ip 10.10.10.0 0.0.0.255 host 10.10.131.63
ip access-list extended SA-CRYPTO-ACL
permit ip 10.96.21.0 0.0.0.255 host 10.99.2.95
ip access-list extended SA-NAT-ACL
permit ip 10.10.10.0 0.0.0.255 host 10.99.2.95
Another solution is more complex and harder to understand (and explain), you can use Virtual models with tunnel-protection for each customer, VRF and NAT for common services.
___
HTH. Please rate this post if this has been helpful. If it solves your problem, please mark this message as "right answer".
-
Use the second router to extend the network to Time Capsule
I have a v7.6.7 running Time Capsule 1 TB and older airport. I'm hoping to add a second router in a new location, and I use an ethernet cable from the TC at the new router (TP Link Archer C5), updated to the latest version of the firmware. The IP address of the TC is 192.168.1.1.
I have set up my router C5 as follows: allocation of IP 192.168.1.199, value DHCP = off, and I connect a cable between the TC ports and port WAN (not Internet) available on the C5. In the C5 wireless settings, I tried both using the TC SSID and pw and creating a new SSID and pw. In both cases, the network will work for a short time, but eventually the entire network, including the TC, stops working. I made no changes to the parameters of the TC on any trial.
Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router? If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?
Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router?
Yes. That would be the basis of a network of mobile type.
The key for a roaming network parameters are:
- The 'primary' router must be configured as a router. In other words, it must have active NAT and DHCP services.
- All other routers used in a network of roaming must be reconfigured as a bridge.
- All routers must broadcast a Wi - Fi network that uses the same network (SSID, aka) name, and the type of wireless security, and the password.
- All routers must be interconnected by Ethernet. To provide Powerline adapters using an Ethernet connectivity should also work.
If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?
Should not really which is the main in the roaming network.
I think at this point, your current circuit line. To check that, I would suggest that you consider to bring back the router C5 in the same room as you have the TC. Then connect it directly to one of the LAN of the TC ports. Complete the entire upward to a mobile network and test it. If everything works, bring back the C5 in the desired location, and then try again.
If it fails, then the circuit line will be tested to check that it provides a solid 'Ethernet' connection between the adapters.
-
Airport of Port Forwarding is more?
So I'm pretty new to this network thing. I don't know the technical network terms then please do not use (or at least their simplification). So I managed to set up my ASUS RT - something something router. I also put in some rules to sink my Xbox One anywhere port forwarding. However, I had problems with port forwarding, so I just used the dmz for her service. However, given that I had to move my Xbox to another part of my house with worst network connection, set up a time capsule for the network. After a long time, I managed to do the work, but now I can listen to is no longer my Xbox. My guess is that the port forwarding rules are not carriers, as it connected via ethernet time capsule and the capsule is connected to another time capsule via radio and this time capsule is connected to my ASUS router via ethernet. So my question is: how to transfer the required ports to my Xbox?
If both of your time Capsules are configured as bridges, the Asus router is the one that needs to be set up on port mapping. The port mapping is used only when a router is configured for routing. In other words, the NAT and DHCP services are enabled. This is the default value for any router.
Just to make sure that I understand your current network configuration, the following is correct?
- ASUS > Time Capsule > > > Time Capsule > Xbox, where ' > ' represents a wired connection, and ' > > > ' represents a wireless.
-
AnyConnect client can not access local network
Hello
I have a problem with the Cisco anyconnect. Once clients are connected they cannot access anything whatsoever, including their default gateway.
Pool of the VPN client is on the same subnet as the LAN (139.16.1.x/24). Local network clients can access DMZ, VPN clients can ping computers on the local network, but they cannot access the DMZ.
I guess that any rule providing that traffic is absent but I m new with Cisco ASA and I m totally lost. I read as much as I could on this topic, but I do not understand which rule is necessary.
Thank you very much in advance for your support.
ASA release 9.4 (1)
!
ciscoasa hostname
activate the encrypted password of WmlxhdtfAnw9XbcA
TA.qizy4R//ChqQH encrypted passwd
names of
mask 139.16.1.50 - 139.16.1.80 255.255.255.0 IP local pool Pool_139
!
interface GigabitEthernet1/1
nameif outside
security-level 0
192.168.1.100 IP address 255.255.255.0
!
interface GigabitEthernet1/2
nameif inside
security-level 100
IP 139.16.1.1 255.255.255.0
!
interface GigabitEthernet1/3
nameif DMZ
security-level 50
IP 172.16.1.1 255.255.255.0
!
interface GigabitEthernet1/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/5
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/6
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/7
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/8
Shutdown
No nameif
no level of security
no ip address
!
Management1/1 interface
management only
nameif management
security-level 100
11.11.11.11 IP address 255.255.255.0
!
passive FTP mode
network obj_any object
subnet 0.0.0.0 0.0.0.0
internal subnet object-
139.16.1.0 subnet 255.255.255.0
network dmz subnet object
subnet 172.16.1.0 255.255.255.0
wialon Server external ip network object
Home 192.168.1.132
wialon-Server network objects
Home 172.16.1.69
Wialon-service-TCP object service
destination tcp source between 1 65535 21999 20100 service range
Wialon-service-UDP object service
destination service udp source between 0 65535 21999 20100 range
network of the NETWORK_OBJ_139.16.1.0_25 object
subnet 139.16.1.0 255.255.255.128
outside_acl list extended access permit tcp any object wialon-Server eq www
outside_acl list extended access allowed object Wialon-service-TCP any wialon-server object
outside_acl list extended access allowed object Wialon-service-UDP any wialon-server object
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 DMZ
management of MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source any any static destination NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 non-proxy-arp-search to itinerary
!
network obj_any object
dynamic NAT (all, outside) interface
internal subnet object-
NAT dynamic interface (indoor, outdoor)
wialon-Server network objects
NAT (DMZ, external) service wialon Server external ip static tcp www www
Access-group outside_acl in interface outside
Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
identity of the user by default-domain LOCAL
Enable http server
http 11.11.11.0 255.255.255.0 management
http 139.16.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
service sw-reset button
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
domain name full ciscoasa.srdongato.null
E-mail [email protected] / * /
name of the object CN = srdongato
Serial number
Proxy-loc-transmitter
Configure CRL
Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
registration auto
full domain name no
name of the object CN = 139.16.1.1, CN = ciscoasa
ASDM_LAUNCHER key pair
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint0 certificates
certificate 09836256
30820381 30820269 a0030201 02020409 83625630 0d06092a 864886f7 0d 010105
05003050 31123010 06035504 03130973 72646f6e 6761746f 313 has 3012 06035504
05130b4a a 41443139 32323033 34343024 06092, 86 01090216 17636973 4886f70d
636f6173 612e7372 646f6e67 61746f2e 6e756c6c 31353132 30353036 301e170d
5a170d32 33333535 35313230 32303633 3335355a 30503112 30100603 55040313
09737264 6f6e6761 30120603 55040513 31393232 30333434 0b4a4144 746f313a
2a 864886 30240609 f70d0109 6973636f 02161763 6173612e 7372646f 6e676174
6f2e6e75 6c6c3082 0122300d 06092 has 86 01010105 00038201 0f003082 4886f70d
010a 0282 010100d 2 295e679c 153e8b6a d3f6131d 8ea646e3 aa0a5fa9 20e49259
ca895563 7e818047 033a4e8f 57f619e9 fa93bfd5 6c44141f b0abf2c0 8b86334e
bac63f41 99e6d676 c689dcf7 080f2715 038a8e1b 694a00de 7124565e a1948f09
8dbeffab c7c8a028 741c5b10 d0ede5e9 599f38fe 5b88f678 4decdc4b b 353, 6708
cfa2fbce f58be06e 18feba56 4b2b04a1 77773ec6 5c58d2ed d7ca4f17 980f0353
138bfe65 1b1165e6 7b6f94bb ab4d4286 e900178c 147a6dba 2427f38e e225030f
0a66d1eb 5075c57e 6d77e5bb 247f5bc3 8d3530f0 49dedf2d 21a24b5f daa08d98
690183cf e82a6b8d 5e489956 c5eecdbc 7fc2365c b629a52b 126b51e2 18590ed5
c9da8503 a639f102 03010001 a3633061 300f0603 551d 1301 01ff0405 30030101
ff300e06 03551d0f 0101ff04 86301f06 04030201 23 04183016 80143468 03551d
dec79103 0a91b530 1ada7e47 7e27b16d 4186301d 0603551d 0e041604 143468de
c791030a 91b5301a da7e477e 27b16d41 86300d 86f70d01 01050500 06 092 a 8648
003cdb04 03820101 8ef5ed31 c05c684b ad2b0062 96bfd39a ecb0a3fe 547aebe5
14b753e7 89f55827 3d4e0aa8 b8674e45 80d4c023 8e99a7b4 0907d 347 060a2fe4
fa6e0c2f 3b9cd708 a539c09f 7022d2ee fb6e2cf6 82b0e861 a2839a71 1512b3ec
e28664e9 732270c 9 d1c679d9 1eaf2ad5 31c3ff97 09aae869 88677a3d b 007, 5699
ecb3032e 2dd0f74f 81f9a8fb 79f30809 723bbdbf dfef4154 5ad6b012 a8f37093
481fa678 b44b0290 23390036 042828f3 5eefdc43 ebe52d26 78934455 9b4234a9
4146 166e5adc b431f12f 8d0fbf16 46306228 731c bfeebc43 34 76984 d2e6ebbc
88ca120a 96838694 d4f32884 963e7385 987ec6b0 dfa28d49 05ba5fa8 641bcfc7
ff92ac3c 52
quit smoking
string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
Certificate 0 is 836256
308202cc a0030201 0202040a 0d06092a 83625630 864886f7 0d 010105 308201b 4
05003028 06035504 03130863 61736131 13301106 03550403 6973636f 3111300f
130a 3133 392e3136 2e312e31 31353132 30353036 35363236 5a170d32 301e170d
35313230 32303635 3632365a 30283111 55040313 08636973 636f6173 300f0603
61311330 11060355 0403130 3133392e 31362e31 2e313082 0122300d 06092 has 86
4886f70d 01010105 00038201 0f003082 010 has 0282 010100e7 a5c16e86 16c15a10
e018b868 bac7271a 30f1a3f8 ecb9c6b8 3ed4b1ad c9468f5e 287f2a7a 644f1496
c43a061e da927d09 a755b53e ed7c6a66 f2f1fb1e f944345c 86e08ce0 891c99b3
13101ab3 04963fad f91f987f 99f22a89 cd1e8c5a 5e4c026d 2cadd7b7 6620bbd1
b4a5135b 24ec886f fa061a06 dd536e96 1e483730 756c 4101 23f83a8d 944a7fbe
93c51d56 32ac0d17 ceb75f63 0ae24f07 f2c54e83 5b84ff00 16b0b899 c925c737
1765b 066 23 b 54645 bc419684 d09dd130 c1479949 68b0a779 df39b078 6fb0deb9
758b14c3 f0801faf f0ad60e1 a018ffba d769f867 3fe8e5fc 88ccc5b2 2319f5d4
617a78c4 74e7a64b 5c68276c 06ea57c1 d0ffce4b 358c4d02 03010001 300 d 0609
2a 864886 05050003 82010100 dff97c9f 4256fd47 8eb661fd d22ecea4 f70d0101
589eff09 958e01f1 a435a20e 5ed1cf19 af42e54d d61fc0ab cb2ee7ac 7fcb4513
1a44cc86 1e020d72 3a3f78d2 4 d 225177 857093d 9 f5fcf3c7 6e656d2b 54a0c522
f636b8cf 33c5ae34 ea340f32 85dff4c1 50165e7a e94de10b ced15752 0b3a76c1
2a50777b 20291106 a1a8a214 a 8 003716 680c15d4 ac3f7cc7 378f8f5f 38e3403f
f958c095 e549c8ed 4baf8cc5 bdcd230e 260754ea 953c3a4c eb01fef5 62b97e01
9f82ce6b f479dbdd 000c45af 8758b35f b4a958ee 32c4db3f 2ddc7385 dc05b0e3
78b609ba a9280841 2433ae87 5dd7a7c2 d5691068 1dc0eddc c23f99c5 3df8b1a5
aadbd82a 423f4ba8 563142bf 742771c 3
quit smoking
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
Telnet 139.16.1.0 255.255.255.0 inside
Telnet 11.11.11.0 255.255.255.0 management
Telnet timeout 5
without ssh stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 172.16.1.69 - DMZ 172.16.1.69
dhcpd dns 87.216.1.65 87.216.1.66 DMZ interface
dhcpd option 3 ip 172.16.1.1 DMZ interface
dhcpd enable DMZ
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust outside ASDM_TrustPoint0 point
SSL-trust ASDM_Launcher_Access_TrustPoint_0 inside point
Trust ASDM_Launcher_Access_TrustPoint_0 inside the vpnlb-ip SSL-point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-3.1.12020-k9.pkg 1
AnyConnect profiles Wialon_client_profile disk0: / Wialon_client_profile.xml
AnyConnect enable
tunnel-group-list activate
Disable error recovery
internal GroupPolicy_Wialon group strategy
attributes of Group Policy GroupPolicy_Wialon
WINS server no
value of 192.168.1.1 DNS server
client ssl-VPN-tunnel-Protocol ikev2
by default no
WebVPN
AnyConnect value Wialon_client_profile type user profiles
dynamic-access-policy-registration DfltAccessPolicy
wialon_1 Wy2aFpAQTXQavfJD username encrypted password
wialon_2 4STJ9bvyWxOTxIyH encrypted password username
remote access to Wialon tunnel-group type
attributes global-tunnel-group Wialon
address pool Pool_139
Group Policy - by default-GroupPolicy_Wialon
tunnel-group Wialon webvpn-attributes
enable Wialon group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447ec315ae30818a98f705fb1bf3fd75Hello
You don't have NAT exemption the DMZ network to the pool of VPN traffic.
Please try to add the following statement to run:
nat (DMZ,outside) 1 source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 route-lookup
Also please delete the existing instruction manual nat "non-proxy-arp" statement, because it can cause problems like you the ip subnet address pool is identical to that of the Interior of the network.no nat (inside,outside) source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 no-proxy-arp route-lookup nat (inside,outside) 1 source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 route-lookup
Cordially Véronique -
Help! Several problem of the setup of site-to-site VPN connection
Recently, I place ASA 5505 on 3 sites and communicate with VPN site-to-site. I am able to connect HQ for two offices without any problem. And each office connect as weel. However, I can't do desktop connection remote at camp. Please see below for each configuration of office and thanks to any part of your experience.
(Pri:172.29.88.254 remote desktop; Pub: 173.190.234.138; Subnet:172.29.88.0/24)
|
| (VPN)
|
HQ office (Pri: 172.29.8.254;) Pub: 173.111.222.140; Subnet: 172.29.8.0/24)
|
| (VPN)
|
Colo (Pri: 172.29.168.254;) Pub: 111.167.239.218; Subnet: 172.29.168.0/24)
Configuration of HQ ASA5505-
ASA 4,0000 Version 1
!
hostname jtfw-AC
domain jollytech.com
activate the encrypted password of Yr4Jr0JzJxYTTQQu
GCdiui.2NH7n52DU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
!
interface Ethernet0/1
switchport access vlan 2
Speed 100
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 172.29.8.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 173.111.222.140 255.255.255.248
!
passive FTP mode
clock timezone GMT 0
DNS server-group DefaultDNS
domain jollytech.com
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
service object RDP
source eq 3389 tcp service
Orange network object
Home 172.29.8.151
network of the WAN_173_111_222_138 object
Home 173.111.222.138
SMTP service object
tcp source eq smtp service
service object PPTP
tcp source eq pptp service
service of the JT_WWW object
tcp source eq www service
service of the JT_HTTPS object
tcp source eq https service
network obj_lex object
172.29.88.0 subnet 255.255.255.0
network of offices of Lexington Description
network obj_HQ object
172.29.8.0 subnet 255.255.255.0
guava network object
Home 172.29.8.3
network obj_HQVPN object
192.168.8.0 subnet 255.255.255.0
jt-fn68zv1 network object
Home 172.29.8.71
service of the JT_FTP object
tcp source eq ftp service
network obj_colo object
172.29.168.0 subnet 255.255.255.0
Standard access list VPN_Tunnel_User allow 172.29.8.0 255.255.255.0
VPN_Tunnel_User standard access list allow 192.168.8.0 255.255.255.0
inside_access_in list extended access permit icmp any one
inside_access_in tcp extended access list deny any any eq idle 135
inside_access_in tcp extended access list refuse any eq 135 all idle state
inside_access_in list extended access deny udp any what eq 135 all idle state
inside_access_in list extended access deny udp any any eq idle 135
inside_access_in tcp extended access list deny any any eq 1591
inside_access_in tcp extended access list refuse any eq 1591 everything
inside_access_in list extended access deny udp any eq which 1591 everything
inside_access_in list extended access deny udp any any eq 1591
inside_access_in tcp extended access list deny any any eq 1214
inside_access_in tcp extended access list refuse any eq 1214 all
inside_access_in list extended access deny udp any any eq 1214
inside_access_in list extended access deny udp any what eq 1214 all
inside_access_in of access allowed any ip an extended list
inside_access_in list extended access permit tcp any any eq www
inside_access_in list extended access permit tcp any eq www everything
outside_access_in list extended access permit icmp any one
outside_access_in list extended access permit tcp any host 173.111.222.138 eq 3389
outside_access_in list extended access permit tcp any host 173.111.222.138 eq smtp
outside_access_in list extended access permit tcp any host 173.111.222.138 eq pptp
outside_access_in list extended access permit tcp any host 173.111.222.138 eq www
outside_access_in list extended access permit tcp any host 173.111.222.138 eq https
outside_access_in of access allowed any ip an extended list
inside_access_out list extended access permit icmp any one
inside_access_out of access allowed any ip an extended list
access extensive list ip 172.29.8.0 outside_cryptomap allow 255.255.255.0 172.29.88.0 255.255.255.0
permit access list extended ip object obj_colo object obj_lex outside_cryptomap
inside_in list extended access permit icmp any one
inside_in of access allowed any ip an extended list
inside_in list extended access udp allowed any any eq isakmp
inside_in list extended access udp allowed any isakmp eq everything
inside_in list extended access udp allowed a whole
inside_in list extended access permitted tcp a whole
permit access list extended ip object obj_HQ object obj_colo outside_cryptomap_1
permit access list extended ip object obj_lex object obj_colo outside_cryptomap_1
pager lines 24
Enable logging
timestamp of the record
logging trap information
asdm of logging of information
address record [email protected] / * /
host of logging inside the 172.29.8.89
Within 1500 MTU
Outside 1500 MTU
mask 192.168.8.100 - 192.168.8.150 255.255.255.0 IP local pool Jolly_HQVPN_DHCP
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT static orange interface (inside, outside) source RDP RDP service
NAT (inside, outside) source obj_HQ destination obj_HQ static static obj_lex obj_lex-route search
NAT (inside, outside) source obj_HQ destination obj_HQ static static obj_colo obj_colo-route search
NAT (inside, outside) source obj_colo destination obj_colo static static obj_lex obj_lex-route search
NAT (inside, outside) source obj_lex destination obj_lex static static obj_colo obj_colo-route search
NAT guava Shared source (internal, external) WAN_173_164_222_138 service JT_WWW JT_WWW
NAT guava Shared source (internal, external) WAN_173_164_222_138 service JT_HTTPS JT_HTTPS
NAT guava Shared source (internal, external) WAN_173_164_222_138 service RDP RDP
NAT guava Shared source (internal, external) WAN_173_164_222_138 SMTP SMTP service
NAT guava Shared source (internal, external) WAN_173_164_222_138 PPTP PPTP service
NAT interface service (Interior, exterior) source static jt-fn68zv1 JT_FTP JT_FTP
NAT (inside, outside) source obj_HQ destination obj_HQ static static obj_HQVPN obj_HQVPN
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 173.111.222.142 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt guava
AAA-server host 172.29.8.3 guava (inside)
Timeout 15
guava auth - NT domain controller
identity of the user by default-domain LOCAL
identity of the user inactive-user-timer minutes 360
Enable http server
http 172.29.8.0 255.255.255.0 inside
SNMP-server host within the 172.29.8.89 community * version 2 c
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac Remote_VPN_Set ikev1
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto-map Dynamics 20 ikev1 transform-set Remote_VPN_Set set outside_dyn_map
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 173.190.234.138
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5
ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA'RE
P-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
card crypto outside_map 2 match address outside_cryptomap_1
card crypto outside_map 2 set pfs
peer set card crypto outside_map 2 111.167.239.218
card crypto outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5
ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA'RE
P-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 2 set AES AES192 AES256 3DES ipsec-proposal ikev2
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet 172.29.8.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
dhcpd auto_config off vpnclient-wins-override
!
dhcprelay Server 172.29.8.3 on the inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
internal Jolleytech_VPN group strategy
attributes of Group Policy Jolleytech_VPN
value of server DNS 172.29.8.3
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_Tunnel_User
jollytech.local value by default-field
internal GroupPolicy_10.8.8.1 group strategy
attributes of Group Policy GroupPolicy_10.8.8.1
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
name of user who encrypted password eicyrfJBrqOaxQvS
type tunnel-group jollytech remote access
tunnel-group jollytech General-attributes
address pool Jolly_HQVPN_DHCP
authentication-server-group guava
Group Policy - by default-Jolleytech_VPN
jollytech group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
tunnel-group 111.167.239.218 type ipsec-l2l
tunnel-group 111.167.239.218 General-attributes
Group - default policy - GroupPolicy_10.8.8.1
IPSec-attributes tunnel-group 111.167.239.218
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
tunnel-group 173.190.234.138 type ipsec-l2l
tunnel-group 173.190.234.138 General-attributes
Group - default policy - GroupPolicy_10.8.8.1
IPSec-attributes tunnel-group 173.190.234.138
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
Policy-map global_policy
class inspection_default
inspect the pptp
inspect the ftp
inspect the netbios
inspect the http
!
global service-policy global_policy
172.29.8.3 SMTP server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:2da829cf9fd3d4901e8131c2ae32b679
: end
Configuration of remote desktop-
ASA Version 8.4 (3)
!
hostname jtfw-lex
activate the encrypted password of Yr4Jr0JzJxYTTQQu
GCdiui.2NH7n52DU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 2
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 172.29.88.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 173.190.234.138 255.255.255.248
!
passive FTP mode
network obj_any object
subnet 0.0.0.0 0.0.0.0
service object RDP
source eq 3389 tcp service
SMTP service object
tcp source eq smtp service
service object PPTP
tcp source eq pptp service
service of the JT_WWW object
tcp source eq www service
service of the JT_HTTPS object
tcp source eq https service
jt-dc01 network object
Home 172.29.88.151
network of the object WAN_jt-dc01
Home 10.8.8.3
network obj_lex object
172.29.88.0 subnet 255.255.255.0
network of offices of Lexinton Description
network obj_HQ object
172.29.8.0 subnet 255.255.255.0
network Jollytech HQ Description
network obj_colo object
172.29.168.0 subnet 255.255.255.0
network of colo Jollytech Description
inside_access_in list extended access permit icmp any one
inside_access_in tcp extended access list deny any any eq idle netbios-ssn
inside_access_in tcp extended access list refuse any netbios-ssn eq all idle state
inside_access_in list extended access deny udp any what eq 139 all
inside_access_in list extended access deny udp any any eq 139
inside_access_in tcp extended access list deny any any eq 135
inside_access_in tcp extended access list refuse any eq 135 everything
inside_access_in list extended access deny udp any what eq 135 everything
inside_access_in list extended access deny udp any any eq 135
inside_access_in tcp extended access list deny any any eq 1591
inside_access_in tcp extended access list refuse any eq 1591 everything
inside_access_in list extended access deny udp any eq which 1591 everything
inside_access_in list extended access deny udp any any eq 1591
inside_access_in tcp extended access list deny any any eq 1214
inside_access_in tcp extended access list refuse any eq 1214 all
inside_access_in list extended access deny udp any what eq 1214 all
inside_access_in list extended access deny udp any any eq 1214
inside_access_in of access allowed any ip an extended list
outside_access_in list extended access permit icmp any one
outside_access_in list extended access permit tcp any host 10.8.8.3 eq smtp
outside_access_in list extended access permit tcp any host 10.8.8.3 eq pptp
outside_access_in list extended access permit tcp any host 10.8.8.3 eq www
outside_access_in list extended access permit tcp any host 10.8.8.3 eq https
outside_access_in list extended access permit tcp any host 10.8.8.3 eq 3389
outside_access_in of access allowed any ip an extended list
inside_access_out list extended access permit icmp any one
access extensive list ip 172.29.88.0 outside_cryptomap allow 255.255.255.0 object obj_HQ
permit access list extended ip object obj_lex object obj_colo outside_cryptomap
Standard access list VPN_Tunnel_user allow 172.29.88.0 255.255.255.0
Standard access list VPN_Tunnel_user allow 172.29.8.0 255.255.255.0
Standard access list VPN_Tunnel_user allow 172.29.168.0 255.255.255.0
Standard access list VPN_Tunnel_user allow 192.168.88.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool jolly_lex_DHCP 192.168.88.100 - 192.168.88.120 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT WAN_jt-dc01 service (Interior, exterior) source static jt-dc01 RDP RDP
NAT static (inside, outside) source JT_WWW JT_WWW WAN_jt-dc01 jt-dc01 service
NAT (inside, outside) source obj_lex destination obj_lex static static obj_HQ obj_HQ-route search
NAT (inside, outside) source obj_lex destination obj_lex static static obj_colo obj_colo-route search
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 173.190.234.137 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 172.29.88.0 255.255.255.0 inside
SNMP-server host within the 172.29.88.30 community * version 2 c
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac Remote_VPN_set ikev1
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 173.111.222.140
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5
ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA'RE
P-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet 172.29.88.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 172.29.88.50 - 172.29.88.100 inside
dhcpd dns 172.29.8.3 166.102.165.11 interface inside
dhcpd jollytech.local area inside interface
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal GroupPolicy_173.164.222.140 group strategy
attributes of Group Policy GroupPolicy_173.164.222.140
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
name of user who has encrypted password JOYSoaqW4x32VHKB
tunnel-group 173.111.222.140 type ipsec-l2l
tunnel-group 173.111.222.140 general-attributes
Group - default policy - GroupPolicy_173.164.222.140
IPSec-attributes tunnel-group 173.111.222.140
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
Policy-map global_policy
class inspection_default
inspect the pptp
inspect the ftp
inspect the netbios
!
global service-policy global_policy
172.29.8.3 SMTP server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:0a0cf040a1f0f979ff55f0ef7e15c452
: end
Configuration Colo-
ASA Version 8.4 (3)
!
hostname jtfw-colo
domain jollytech.com
activate the encrypted password of Yr4Jr0JzJxYTTQQu
GCdiui.2NH7n52DU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 2
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 172.29.168.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 111.167.239.218 255.255.255.248
!
passive FTP mode
clock timezone GMT 0
DNS server-group DefaultDNS
domain jollytech.com
network obj_any object
subnet 0.0.0.0 0.0.0.0
service object RDP
source eq 3389 tcp service
SMTP service object
tcp source eq smtp service
service object PPTP
tcp source eq pptp service
service of the JT_WWW object
tcp source eq www service
service of the JT_HTTPS object
tcp source eq https service
network obj_lex object
172.29.88.0 subnet 255.255.255.0
network of offices of Lexington Description
network obj_HQ object
172.29.8.0 subnet 255.255.255.0
network Jollytech HQ Description
guava network object
Home 172.29.8.3
network obj_HQVPN object
192.168.8.0 subnet 255.255.255.0
Description Jollytech HQ VPN network
network of the WAN_111_167_239_220 object
Home 111.167.239.220
jt-dc01 network object
Home 172.29.168.3
jt-exch2010 network object
Home 172.29.168.25
network obj_colo object
172.29.168.0 subnet 255.255.255.0
network of colo Jollytech Description
network of the object RC_jt-r610
Home 172.29.168.8
network of the WAN_111_167_239_221 object
Home 111.167.239.221
inside_access_in list extended access permit icmp any one
inside_access_in tcp extended access list deny any any eq idle 135
inside_access_in tcp extended access list refuse any eq 135 all idle state
inside_access_in list extended access deny udp any what eq 135 everything
inside_access_in list extended access deny udp any any eq 135
inside_access_in tcp extended access list deny any any eq 1591
inside_access_in tcp extended access list refuse any eq 1591 everything
inside_access_in list extended access deny udp any eq which 1591 everything
inside_access_in list extended access deny udp any any eq 1591
inside_access_in tcp extended access list deny any any eq 1214
inside_access_in tcp extended access list refuse any eq 1214 all
inside_access_in list extended access deny udp any any eq 1214
inside_access_in list extended access deny udp any what eq 1214 all
inside_access_in list extended access permit tcp any any eq www
inside_access_in list extended access permit tcp any eq www everything
inside_access_in of access allowed any ip an extended list
outside_access_in list extended access permit icmp any one
outside_access_in list extended access permit tcp any object WAN_198_167_239_220 eq 3389
outside_access_in list extended access permit tcp any object WAN_198_167_239_220 eq www
outside_access_in list extended access permit tcp any object https eq WAN_198_167_239_220
outside_access_in list extended access permit tcp any object WAN_198_167_239_221 eq www
outside_access_in list extended access permit tcp any object https eq WAN_198_167_239_221
outside_access_in list extended access permit tcp any object WAN_198_167_239_221 eq 3389
outside_access_in of access allowed any ip an extended list
inside_access_out list extended access permit icmp any one
inside_access_out of access allowed any ip an extended list
permit access list extended ip object obj_colo object obj_HQ outside_cryptomap
permit access list extended ip object obj_colo object obj_lex outside_cryptomap
pager lines 24
Enable logging
asdm of logging of information
address record [email protected] / * /
exploitation forest-address recipient [email protected] / * / level of errors
host of logging inside the 172.29.168.89
Within 1500 MTU
Outside 1500 MTU
mask 192.168.168.100 - 192.168.168.110 255.255.255.0 IP local pool Jolly_coloVPN_DHCP
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT of the service interface to the Shared source (internal, external) JT_WWW JT_WWW RC_jt-r610
NAT of the service interface to the Shared source (internal, external) JT_HTTPS JT_HTTPS RC_jt-r610
NAT service of WAN_111_167_239_220 jt-dc01 Shared source (internal, external) JT_HTTPS JT_HTTPS
NAT service of WAN_111_167_239_220 jt-dc01 Shared source (internal, external) JT_WWW JT_WWW
NAT service of WAN_111_167_239_220 jt-dc01 Shared source (inside, outside) RDP RDP
NAT service of WAN_111_167_239_221 jt-exch2010 static source (inside, outside) RDP RDP
NAT source service (Interior, exterior) static jt-exch2010 WAN_111_167_239_221 JT_WWW JT_WWW
NAT source service (Interior, exterior) static jt-exch2010 WAN_111_167_239_221 JT_HTTPS JT_HTTPS
NAT (inside, outside) source obj_colo destination obj_colo static static obj_HQ obj_HQ-route search
NAT (inside, outside) source obj_colo destination obj_colo static static obj_lex obj_lex-route search
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 111.167.239.217 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 172.29.168.0 255.255.255.0 inside
http 172.29.8.0 255.255.255.0 inside
SNMP-server host within the 172.29.168.89 community * version 2 c
location of SNMP server it Fremont Colo
SNMP Server contact [email protected] / * /
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac Remote_VPN_Set ikev1
Crypto ipsec transform-set esp-3des esp-md5-hmac Remote_vpn_set ikev1
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto-map Dynamics 20 ikev1 transform-set Remote_VPN_Set set outside_dyn_map
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 173.111.222.140
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5
ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA'RE
P-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet 172.29.8.0 255.255.255.0 inside
Telnet 172.29.168.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd auto_config off vpnclient-wins-override
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
internal GroupPolicy_173.111.222.140 group strategy
attributes of Group Policy GroupPolicy_173.111.222.140
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
name of user who encrypted password eicyrfJBrqOaxQvS
tunnel-group 173.111.222.140 type ipsec-l2l
tunnel-group 173.111.222.140 general-attributes
Group - default policy - GroupPolicy_173.111.222.140
IPSec-attributes tunnel-group 173.111.222.140
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
Policy-map global_policy
class inspection_default
inspect the pptp
inspect the ftp
inspect the netbios
!
global service-policy global_policy
172.29.8.3 SMTP server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:a45d9f3e7b23713c34d13d5a8ac5ece5
: end
Hello
I think that these NAT configurations must change in the ASA HQ
NAT (inside, outside) source obj_colo destination obj_colo static static obj_lex obj_lex-route search
NAT (inside, outside) source obj_lex destination obj_lex static static obj_colo obj_colo-route search
Note that you must configure to use 'inside' and 'outside' interface.
However if two remote sites put an end to the ASA HQ "outside" interface and the traffic between these remote sites (that go through this ASA HQ) actually must a NAT between 'outside' and 'outside '.
You will need to use the (outside, outside) in the NAT configurations.
NAT (outside, outside) source obj_colo destination obj_colo static static obj_lex obj_lex-route search
NAT (outside, outside) source obj_lex destination obj_lex static static obj_colo obj_colo-route search
You could actually be fine with either NAT 2 only two-way configurations as it should.
-Jouni
-
Freezing of construction-2496824 VMWare Workstation 11.1.0
Hello
I have a Windows 7 x 64 using Workstation 11.1.0 host (assessment of the trial). I have a Windows 8.1 Pro x 64 running virtual machine. It is the only virtual machine running. A few minutes after starting the virtual machine, the virtual machine and the Workstation locks.
I do Ctrl + Alt + Delete and open the host Task Manager. VMware.exe is always 25% of the CPU (I have a Core i7-4600U, so there are 4 cores with hypertheads). VMware - vmx.exe CPU usuage varies. My only option is to kill the process vmware.exe. Then, the host runs normally. To run the windows 8.1 host once again, I have to restart the computer, as it says the prompt is used.
When the computer restarts normally that's fine. But this time he started running slow after a minute. I opened the windows Task Manager. Once it is open (after 10 minutes) I found that the CPU utilization was only 1% or more. After 10 or 15 minutes of looking around, I started to kill the VMware processes. After that I took some to the host ran normally. It's working normally now.
The issue of freezing happened 4 or 5 times in two or three days. When I kill computer vmware.exe always goes back to normal.
I did a few things like proactive:
(1) add folder VM to the exclusion list antivirus, windows search, exclusion of our backup software list exclusion list.
(2) remove the floppy and CD drive from the list of virtual machine hardware. I read that could cause a hang upwards.
The event log does not contain something interesting. I have attached all newspapers of vmware, I have for the machine virtual windows 8.1.
Any suggestions on what I can do next to try to solve this further?
The host is not lock it just the vmware workstation app. I wanted to clarify that.
Other than the VM Pro 8.1 Windows only other VM I have is Windows XP Mode. I started the XP Mode VM and it has always worked very well after having worked in the virtual machine for an hour. I then restarted the VM of Windows 8.1 and three minutes later, he locked and workstation. I see two vmware - vmx.exe treated one to 25% CPU usage in Task Manager (I presume VM Windows 8.1) and the other with barley any use of CPU (likey XP Mode). Vmware.exe also has 25% CPU usage as before.
I'm in the resource monitor and to suspend the process vmware - vmx.exe which uses 25% cpu and now a workstation and the XP Mode VM work properly. I then clicked on 'stop' the machine virtual windows 8.1 and has resumed the vmx process. VM stop the 8.1 Windows workstation with success. Workstation and the XP Mode VM still work normally.
So certainly issue between the workstation and the machine virtual windows 8.1 but I am not a guru vm or work station, so I can't determine what is the question.
Edit
Repeat the question. Is a wait analyze on vmware.exe chain in resource monitored and must wait on himself: "one or more threads to vmware.exe wait to finish i/o network." and "vmware.exe PID XXXX 6208" Thread. So some kind of blocking of the thread? When I suspend the vmware - vmx.exe running to my VM of Windows 8.1 then the vmware.exe CPU usage goes to 0%. But the wait vmware.exe watch chain still he waits on itself with the same message as above. I then return to the vmware-vmx process and the CPU goes up to 25%.
I can fix things without killing the process vmware or vmx suspend windows 8.1 vmx process, use windows 7 taskbar live preview for click shutdown (square button) and then resume the vmx process. At that point the 8.1 windows vm shutsdown immediately and the workstation (with the xp mode vm) is operating normally.
He has worked to find a few days but starting to give me this problem.
Edit2
OK problem solved I think. Our IT technician installed Malwarebytes Anti-malware over another anti-virus/anti-malware program. Which was causing the computer to 'lock' (run slow but cpu was near 0% so desire ' cpu loading) during start, sounds a different problem than what I saw, but it may affect both workstation. Also my VMs used NAT so I tried to switch to bridged and disabled the NAT and DHCP service. Featured two fewer services to run. Don't know which of those (if any) was causing the problem, but after those changes it works (for the most part very well).
Wes
-
WinRunner license with VMware Workstation
Evaluate us VMware Workstation 10.0 and we try to install Winrunner on a virtual machine but the Winrunner trying to get out to the network on the virtual machine to find the license competition, every time, we have created (OS Win 7), installation is suspended. The error indicates the installation Winrunner is unable to find the license on the network.
Verified that the network is in place and works very well. Check that the license exists on the network (installed on another computer to test using a ghost image). Anyone got any ideas on why installing Winrunner can not find the license?
Concerning
Your guest VM is configured to use NAT or Bridged network mode? Not sure if it would be serious, but it is possible - if it's NAT - the license service is unable to return to the virtual machine.
-
unstall Miscosoft NET framework 2.0 service pack 2 because I also have Miscosoft. NET Framework 3.0 service pack 2 and 3.5 SPI
Hello mortgage by crosswind,
I would not uninstall earlier versions of the .NET Framework on your computer. Some applications are written only search a specific version, therefore, the application may not work if you delete the old version.
Please click on item below to view the article dealing with this information.
KB Article ID: 829019 -benefits of the Microsoft .NET FrameworkI hope this helps answer your question.
Sincerely,
Marilyn
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think -
How to change the Nat setting on valet parking for Xbox to work properly
My NAT type is moderate and I do not allow me to use all the features of XBox... live is possible to change these settings?
Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...
If you have installed the software router using Cisco connect then the wireless network key will be the password of the router.
On the Configuration tab change the size of the MTU to 1365, then click on save settings...
Click the 'Administration' tab and disable the UPnP option and click on save settings...
Click on the tab "Games and Applications" and then click the sub-tab "Port Range Forwarding"...(1) on the first line in the box, type Application in ABC, in the start box, type in 53 and type in 3074 service box, leave the Protocol as and under type 192.168.1.20 ip address and check the box to enable, click on save settings once it's been...
(2) once you return to the game to the top page, click the Security tab and uncheck block anonymous Internet requests and click on save settings...
(3) click on the status tab, and then note the DNS1 and DNS2 addresses...
4) go to the XBox network settings and IP address settings, select manual IP settings and assign the following on your Xbox IP address:-192.168.1.20 subnet mask:-255.255.255.0, default gateway:-192.168.1.1...
(5) also assign addresses DNS Xbox DNS1 and DNS2 use addresses you took note of the primary router as secondary DNS & DNS status tab for the xbox...
(6) turn off your modem, router and Xbox... Wait a minute...
(7) connect the power supply to the modem first, wait another minute and plug the router power cable, wait another minute and turn on the Xbox and test... It will connect...
-
Access to services: conflict NAT and VPN
Hi people!
I encountered a problem with external access to local services of:
(a) remote clients (port open on the side WAN)
(b) the remote sites (through IPsec tunnels)Here's a topology:
EXPLANATIONS
FW1 (actually from TMG 2010) overload NAT of preforms.
The service in question (for example tcp 9999) is published on 192.168.100.0/24 via static NAT translation, which is accessible from the network.
HQ1 is a border router (cisco 2921). It also performs NAT overload for public addresses. (Other than cisco) Branch1 also performs NAT overload.
All traffic between the headquarters and the remote site is allowed. The service is accessible from the remote site.
PROBLEM
I want to allow access to the service for an external user (remote user). I do the following configuration:
IP nat inside source static tcp 192.168.100.2 2.2.2.2 9999 9999 extensible
After this command remote user is able to access the service by public IP, BUT the site's users remote losing it. If I roll back with
No nat ip inside the source static tcp 192.168.100.2 2.2.2.2 9999 9999 extensible
then access to the remote site is restored, and remote user lose again. Seems that it is connected with the static NAT translations.
How can I make it work in both cases of simulteniously? Both for the remote site and the remote user.
Thank you!
You must use a map of the route with your static NAT configuration.
Recently answered a question for the same thing, please visit this link and if you have any questions please come back.
https://supportforums.Cisco.com/discussion/12544291/IPSec-IP-NAT-inside-source-static
Jon
-
Special RV220W NAT allows only a single service?
Hello
Just bought a RV220W for a client to replace a WRVS4400N which has no support for individual NAT and stated that the specific NAT for this router is only marginally better.
I have three WAN addresses and three devices to their card. With the RV0xx, I used the following more than a dozen times.
WAN 1 address - public address of the router
Port HTTP, HTTPS and SMTP for Windows Small Business Server 2011
Messaging and remote Web access are available to the remote.company.com
Address WAN 2
One-to-one NAT to Ubuntu Server's private IP address
Add the following access rules:
- All refuse
- Allow everything to the private IP address of the HTTP Server
- Allow SSH to static IP address of my business to private IP
- Allow FTP to static IP address of my business to the private IP address
Companies Web site is accessible to company.com and I can update the site with SSH and FTP
Address WAN 3
One-to-one NAT to private IP address of the module of RMM Intel Server Hyper-V (Lights out remote management)
Add the following access rules:
- All refuse
- Allow HTTP, HTTPS, and RMM all ports of statics of my business to the private IP address of RMM modules
I can access the my business network connection rmm.company.com server
My problems are:
- Specific option NAT requires now allows you to specify the service you want to transfer (Note: service, not services)
- If you select all of the service which is the only way that I can see for having more than one service, there is no way to add any specific Allow or Deny rules because the Destination area is dimmed in page access rules.
- This results in my Ubuntu Server only have HTTP sent to her and my module RMM having all ports open to any IP address.
There must be a way around this! I don't understand why the Destination IP option is grayed out for all inbound access rules. I used this same configuration with the RV0xx of Cisco, many Sonicwall, as well as several Cisco ASA firewalls. Obviously this isn't an ASA, but this individual NAT implementation is useless!
Any help is greatly appreciated. Thank you
Kevin
Due to the GUI limiting to one service in individual NAT page, users must go to the firewall > page access rules to specify additional services are allowed.
-
I have VMware Workstation 12.1 Pro installed on a 64-bit of Windows 10 host.
I created a rule of port forwarding for VMnet8 (NAT network). Through netstat, I can confirm that ports in LISTENING State on the host computer. I can confirm that client ports also work.
As soon as I try to open a connection to the port transferred from the host, the VMware NAT service dies.
If I restart the NAT service, the ports are open again, and again, it will die when I try to connect.
Here are the relevant messages in the event viewer:
Log name: Application
Source: VMware NAT Service
Date: 29/01/2016 13:56:03
Event ID: 1000
Task category: no
Level: Information
Keywords: Classic
User: n/a
Description:
Service started
Log name: Application
Source: VMware NAT Service
Date: 29/01/2016 13:56:03
Event ID: 1000
Task category: no
Level: Information
Keywords: Classic
User: n/a
Description:
Using the configuration file: C:\ProgramData\VMware\vmnetnat.conf.
IP address: 192.168.169.2
Subnet: 255.255.255.0
External IP address: 0.0.0.0
Feature: vmnet8.
MAC address: 00:50:56:EB:9 A: 84.
Ignore the MAC address of the host: 00:50:56:C0:00:08.
Log name: System
Source: Service Control Manager
Date: 29/01/2016 13:56:19
Event ID: 7034
Task category: no
Level: error
Keywords: Classic
User: n/a
Description:
The service of VMware NAT Service ended unexpectedly. He made this 5 times.
Log name: Application
Source: Application error
Date: 29/01/2016 13:56:19
Event ID: 1000
Task category: (100)
Level: error
Keywords: Classic
User: n/a
Description:
Name of the failing application: vmnat.exe, version: 12.1.0.2487, time stamp: 0x565668d4
Name of the failed module: vmnat.exe, version: 12.1.0.2487, time stamp: 0x565668d4
Exception code: 0xc0000005
Offset: 0x0000befb
ID of the process failing: 0x14e4
Start time of application vulnerabilities: 0x01d15aad8e6ff1a9
The failing application path: C:\Windows\SysWOW64\vmnat.exe
Path of the failing module: C:\Windows\SysWOW64\vmnat.exe
Report ID: 6b76381c-38e4-4cb7-86ee-317f57b61095
Faulting full name of the package:
ID of the failed package-parent application:
Log name: Application
Source: Windows Error Reporting
Date: 29/01/2016 13:56:19
Event ID: 1001
Task category: no
Level: Information
Keywords: Classic
User: n/a
Computer: GTIRLONI
Description:
Bucket of error, type 0
Event name: APPCRASH
Answer: No available
Cabin ID: 0
Signature of the problem:
P1: vmnat.exe
P2: 12.1.0.2487
P3: 565668d 4
P4: vmnat.exe
P5: 12.1.0.2487
P6: 565668d 4
P7: c0000005
P8: 0000befb
P9:
P10:
Attached files:
C:\Windows\Temp\WER1C4B.tmp.AppCompat.txt
C:\Windows\Temp\WER1C5C.tmp.WERInternalMetadata.XML
C:\ProgramData\Microsoft\Windows\WER\ReportQueue\AppCrash_vmnat.exe_20f42c45e9411a26b8a065f72a726fbaef111e76_f3265a09_cab_13cd1c6a\memory. HMDP
C:\ProgramData\Microsoft\Windows\WER\ReportQueue\AppCrash_vmnat.exe_20f42c45e9411a26b8a065f72a726fbaef111e76_f3265a09_cab_13cd1c6a\triagedump.dmp
These files are available here:
C:\ProgramData\Microsoft\Windows\WER\ReportQueue\AppCrash_vmnat.exe_20f42c45e9411a26b8a065f72a726fbaef111e76_f3265a09_cab_13cd1c6a
Symbol of the analysis:
Recheck for solution: 0
Report ID: 6b76381c-38e4-4cb7-86ee-317f57b61095
Display state: 4
Bucket Hashed:
Downgrade to version 12.0.1 "Fixed" the problem.
-
This is my system:
miklasm@miklasmub: cat/etc/issue
Ubuntu 10.04.1 LTS \n \l
miklasmub: / home/miklasm # uname - a
Miklasmub 2.6.32 - 24-generic #38 - Ubuntu Linux SMP kills Jul 5 09:20:59 UTC 2010 x86_64 GNU/Linux
miklasmub: / home/miklasm # vmware - v
VMware Workstation 7.1.0 build 261024
Host: Ubuntu 10 to 100 Mbps wired
Client: Windows XP, network NAT. VM Ware, tools are installed, GUI works fine.
I'm trying to copy 10,000 small files to our FTP server. After a few minutes on the guest network is not responding and I'm getting 'host not found '. After restarting vmware on ubuntu network services work again.
This is the solution for this problem?
Thank you
Maciej
You use NAT that blocks incoming ports, but if you want to use the FTP protocol, the destination trying to open ports to your guest. Try to use the passive FTP as in this case, the server instructs the FTP client which port should be used, and it opens the client (your virtual guest).
Read http://pubs.vmware.com/ws7_ace26/ws_user/ws_net_nat_externalaccess.html#1019966
and http://pubs.vmware.com/ws7_ace26/ws_user/network_adv.17.33.html on how to activate the active FTP.
Or use the bridged network.
AWo
VCP 3 & 4
\[:o]===\[o:]
= You want to have this ad as a ringtone on your mobile phone? =
= Send 'Assignment' to 911 for only $999999,99! =
-
How do I restart services (NAT) vmnet with reboot 'everything '.
Hello
I'm unable to determine how to restart just the services involved in vmnet8 (NAT) for /etc/vmware/vmnet8/nat/nat.conf changes can take effect. I've got other guests running and it looks (reason to upgrade?) unreasonable to have to stop all clients and restart vmware via /etc/init.d/vmware reboot. My reason is the addition of a NAT device would have guest OS and I wish the portability forward to get SSH access. I see nothing in the new interface server 2.x.x web admin to stop and start services NAT/vmnet8. I googled for zero results about 1.5 hours. Any ideas? I am running 2.0.2 on host CentOS 5.x.
Thank you
George
Try the following which should restart all services network for vmnet8 (NAT):
/usr/lib/vmware/net-services.sh restart 8
--
If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.
Maybe you are looking for
-
I'm unable to stop "private browsing".
For some reason any Firefox automatically put me under navigation private when I open it. I try to close private browsing, but the option is grayed out. And the problem is that I don't even know if I'm really in private browsing, because it does not
-
Your computer cannot connect to the remote computer
Hello OT: Your computer cannot connect to the remote computer because the remote desktop gateway server address request and the certificate subject name do not match. Contact your network administrator. I implement the remote desktop session based on
-
HP Pavilion: Information on the new laptop
Hi all I think to change my laptop HP a new but confussed so that one go, can someone explain the benefits or the dissadvantages for following types? Model HPaf157sa with storage processor AMD A8 - 7410 APU is 2 TB other interested model is Model HPa
-
PCI Simple Communication controller
Please help me. In Device Manager / other devices... There's a yellow exclamation mark for PCI Simple Communication controller. Which driver I'm missing to install? Please help me. My laptop is a 4540 of HP Probook running Windows 7 Professional. I n
-
What to do with downloaded Dell Bios / others when asked where you want to unpack these?
Hey people, I know that this is not the place to ask the question, but I have trouble instead of Dell. And Microsoft has always gone through before. I went to Dell downloads looking for things, downloaded the new urgent BIOS and a few others, saved t