Valet parking more speed problem

Similar Questions

• Valet parking more and FIos

  Hello

  I have the router Actiontec of FIOS REV D. and I just bought a Valet Plus with the hope of using it for my wireless, but stay on the same network.

  (1) how to configure the Valet and Actiontec to communicate with each other

  (2) I want to keep the network service customers if it is possible for Valet

  (3) I would be able to use the ethernet ports on both devices and wireless for valet and always be able to communicate between devices.

  (4) Finally, I don't want to disable all FIOS TV services.

  You must connect two routers together with the Ethernet cable.

  You can't connect two routers using the Wi - Fi connection. So there should be a cable between Actiontech router and with valet services more.

  Connection type 1:

  If you want to use the network comments on Valet Plus router then router function or the DHCP server on the Valet more should work.

  Consider that the IP of Actiontach router address is 192.168.1.1. Then connect the cable to the port of Actiontech router to the Internet liked Jack port. Connect the computer to the Valet Plus router and run the Cisco connect software on your computer. The Cisco connect software will automatically create the network invited for plu Valet and it will also change the IP address of the Valet Plus router. In this case, you can use the two routers (wired or wireless) Internet connection and network reviews.

  But Actiontach computers/devices connected to the router will not be able to communicate with the computers/devices connected to the Valet more because of IP address change.

  Type of connection 2:

  In this type of connection, you can connect Actiontech router to more router Ethernet 1 Valet port and use it as an access point or switch.

  Consider the IP of Actiontech router address is 192.168.1.1, then you can change the IP address of Jack more on 192.168.1.2. Disable the DHCP server on the router more Valet.

  In this case, you will not be able to Jack by using the installation CD. You must manually change the settings and you will not be able to use the Valet guest network feature.

  But the computer connected to the Actiontech router will be able to communicate with computers connected to the Valet Plus.

  Follow this link for more information on the cascade of routers

• any ideas? ~ macbook pro (13-inch mid 2009) speed problem & sound a1278 ~ el capitan 10.11.5 (15F34)

  any ideas? ~ macbook pro (13-inch mid 2009) speed problem & sound a1278 ~ el capitan 10.11.5 (15F34)

  
  

  EtreCheck version: 2.9.12 (265)

  Report generated 2016-06-25 16:47:10

  Download EtreCheck from https://etrecheck.com

  Time 02:21

  Performance: Excellent

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Verify the signatures of Apple: enabled

  
  

  Problem: Computer is too slow

  Hardware Information: ⓘ

  MacBook Pro (13-inch, mid 2009)

  [Data sheet] - [User Guide] - [warranty & Service]

  MacBook Pro - model: MacBookPro5, 5

  1 CPU 2.53 GHz Intel Core 2 Duo: 2 strands

  8 GB of RAM expandable - [Instructions]

  BANK 0/DIMM0

  OK 4 GB DDR3 1067 MHz

  BANK 1/DIMM0

  OK 4 GB DDR3 1067 MHz

  Bluetooth: Old - transfer/Airdrop2 not supported

  Wireless: en1: 802.11 a/b/g/n

  Battery: Health = Normal - Cycle count = 7

  Video information: ⓘ

  NVIDIA GeForce 9400M - VRAM: 256 MB

  Color LCD 1280 x 800

  Software: ⓘ

  OS X El Capitan 10.11.5 (15F34) - since startup time: less than an hour

  Disc information: ⓘ

  SAMSUNG SSD 840 EVO 250 GB disk0: (250,06 GB) (Solid State - TRIM: No.)

  EFI (disk0s1) < not mounted >: 210 MB

  a /Volumes (disk0s2) / has: 50,00 (GB 49,84 free)

  b (disk0s3) /: 199,07 go-go (160,81 free)

  Recovery HD (disk0s4) < not mounted > [recovery]: 650 MB

  HL-DT-ST DVD - RW GS23N)

  USB information: ⓘ

  Built-in ISight from Apple Inc..

  Card reader Apple

  Apple Inc. Apple keyboard / Trackpad

  Computer, Inc. Apple IR receiver.

  Apple Inc. BRCM2046 hub.

  Apple Inc. Bluetooth USB host controller.

  Configuration files: ⓘ

  / etc/sudoers, 1242 but file size expected 2299

  Protection of the integrity of system status: disabled

  Guardian: ⓘ

  Any where

  Kernel extensions: ⓘ

  / System/Library/Extensions

  [no charge] com.native - instruments.driver.NIUSBDeviceHelper (1.0.8 (R32) - 2016-06-25) [Support]

  Launch system officers: ⓘ

  [loaded] 7 tasks Apple

  [loading] 165 tasks Apple

  [operation] 66 tasks Apple

  Launch system demons: ⓘ

  [loaded] 47 tasks Apple

  [loading] 164 tasks Apple

  [operation] 79 tasks Apple

  Launch demons: ⓘ

  [loading] com.adobe.fpsaud.plist (2016-06-14) [Support]

  [loading] com.malwarebytes.HelperTool.plist (2016-06-25) [Support]

  User launch officers: ⓘ

  com.apple.CSConfigDotMacCert [fail]-[...] @me.com - SharedServices.Agent.plist (2016-06-23) -/System/Library/Frameworks/CoreServices.framework/Frameworks/OSServices.framewo rk/Versions/A/support/CSConfigDotMacCert: Executable not found!

  [loading] com.google.keystone.agent.plist (2016-06-23) [Support]

  Items in user login: ⓘ

  gfxCardStatus Application (~ / Downloads/gfxCardStatus.app)

  Hidden Google Chrome application (/ Applications/Google Chrome.app)

  NIHardwareAgent Application hidden (/ Library/Application Support/Native Instruments/Hardware/NIHardwareAgent.app)

  Other applications: ⓘ

  [ongoing] com.Apple.XPC.launchd.oneshot.0x10000002.Google Chrome

  [ongoing] com.eidac.smcFanControl2.54432

  [ongoing] com.etresoft.EtreCheck.6112

  com.google.Chrome.47072 [loading]

  com.native-[ongoing] instruments.NIHardwareService.54752

  [loading] 411 tasks Apple

  [operation] 176 tasks Apple

  Plug-ins Internet: ⓘ

  FlashPlayer - 10.6: 22.0.0.192 - SDK 10.9 (2016-06-23) [Support]

  QuickTime Plugin: 7.7.3 (2016-06-25)

  Flash Player: 22.0.0.192 - SDK 10.9 (2016-06-23) [Support]

  JavaAppletPlugin: 15.0.1 - 10.11 (2016-06-23) check the version of the SDK

  Default browser: 601 - SDK 10.11 (2016-06-25)

  3rd party preference panes: ⓘ

  Flash Player (2016-06-14) [Support]

  Time Machine: ⓘ

  Time Machine not configured!

  Top of page process CPU: ⓘ

  28% by mail

  11% WindowServer

  6% kernel_task

  2% hidd

  1% fontd

  Top of page process of memory: ⓘ

  1.65 GB Google Chrome Helper (13)

  563 MB kernel_task

  Mdworker (19) 360 MB

  221 MB Google Chrome

  Com.apple.WebKit.WebContent (2) 131 MB

  Virtual memory information: ⓘ

  3.77 GB of free RAM

  used 4.48 GB RAM (2,40 GB being cached)

  Used Swap 0 B

  Diagnostic information: ⓘ

  25 June 2016, 16:18:23 self test - passed

  24 June 2016, 18:55:37 ~/Library/Logs/DiagnosticReports/WebProcess_2016-06-24-185537_[redacted].crash

  com.apple.WebProcess - /System/Library/PrivateFrameworks/WebKit2.framework/WebProcess.app/Contents/Mac OS/process Web

  MacBook Pro, average vintage thrash?

  Your hard drive may be faulty, run disk utility > first aid your recovery volume or another hard drive under OS X on it and let us know what he reports.

  https://support.Apple.com/en-us/HT201639

  Edit: you 2009 isn't a recovery, run it from your installation CD original or other dislk with OS X on it.

• Valet parking can be defined as an access point only?

  I'm on ATT U-verse and must use their router but I wish I had an access point "N".  The new valet parking is adjustable as an access point only either turn off the router and DHCP functions?

  Technically Yes, but if you do not set up this way, you will not be able to configure it by using the software, will have to be a manual configuration...

  I recommend the following:

  1. set the Valet for default values (hold the reset for 10 seconds, then release)

  2. connect a PC to the Valet

  3. access to user interface to 192.168.1.1 (if resetting the password will be admin)

  4. go in the wireless tab and configure your SSID and security settings

  -Do not forget to 802.11n you use WPA2 personal security only, nothing else will not give you of top speeds speed

  5. save wireless settings.

  6. go to the basic settings and change the IP address to something different, which I suggest you to 192.168.1.2 (if using another device Linksys or Cisco, as this will help prevent conflicts when you connect your networks together)

  7. save the settings

  8. close the browser and reopen it, access the user interface to the new address 192.168.1.2 (or you have chosen)

  9. on the page basic settings, disable the DHCP server, and then click Save.

  10 disconnect your PC from the Jack and connect the Jack to your network existing (use of the LAN numbered ports to not connect the INTERNET port)

  11. Once you have the LAN ports on the Jack connected to the LAN ports on your existing router, you should be able to pull DHCP from the main router when connected wireless and surf the net...

  Enjoy!

• Satellite A80 129 DVD-RAM write speed problem

  Hi all!

  I have a problem. the thing is that I want to write in NERO 6 (last version purchased) a CD or DVD, but we will only write to me at slow speeds. In this laptop I MAST * a DVD-RAM UJ-830 s with DVD-R 8 x and 24 x CD - R write speed said.

  When I try to write on a CD it gives me only 16 x write speed, then where is x 24? It goes same for DVD, as I want to burn DVDs and it gives me only 2 x write speed.

  Please, do not put this fault on a CD or DVD, cause in my country there are limited suppliers of this type of media, so I won't change my media. They worked with my previous PC CD - RW fine, no speed problem.

  I want to know also if this is lack of DVD - RAM, where then find firmware for this burner?

  Thanks for your replies.

  BR, Kekec

  You should try to update nero, it might solve the problem.

  Also an update of the firmware can help, go to http://www.toshiba-europe.com/storage/index.asp?nav=HOM&page=HOM&frame=home

• the volume appears to contain one or more unrecoverabble problems

  I had a windows pc wth dual boot XP after that I did a system restore to a date that precedes a installed the second version of windows XP my computer start your ups Loopy I can't start in safe mode. I started upward with the recvory cd en windows got massage when I did a chkdsk. the volume appears to contain one or more unrecoverabble problems

  FIXBOOT cannot open the partition

  I had installed a new version on the patition even.

  When I start my PC after the windows screen reboot pc looped you.

  I solved the problem with BartPe. I did a chkdsk and now my pc works well

• Blue screen and after forced registry errors stops under XP, "volume contains one or more unrecoverable problems".

  Hello!  My computer hung on me for quite some time, so a few days ago I had no choice but to make a closed group.  Now, I can't even as much as screen (with the blue bar and the Windows logo).  I tried the following:

  (a) via the Windows Recovery Console chkdsk.  I tried / p, / r, / f, all give me a "volume contains one or more unrecoverable problems." or something like that.  If I try to install a new Windows, as soon as it "looking for previous versions", I get a BAD_POOL_HEADER blue screen with stop error message 0x000000C2.

  (b) I tried to hit every single F shortcut key, but none would let me go in the recovery console (which is F10 for me) and safe mode (which is F8 for me).  Only the F1 works, who has access to my bios Setup, I think.

  If I jump just the recovery console, I just get a white loading bar, who finally stops loading, and then I get a message telling me that one of my files (windows\config\system I think) is missing or damaged.  I tried after a few steps through one of the Windows solutions to counteract this, but I can't even copy/delete files via the command prompt that it denies access.

  Help, please!

  Hello

  · What is the number and the model of the computer?

  You can check the link below

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-performance/what-to-do-about-chkdsk-message-the-volume-appears/e351d02f-F508-489e-AFDC-988d8ddc462c

  Regarding the BAD_POOL_HEADER error, according to the research of mu, it points to be a hardware problem with the memory or a driver issue as possible.

  We can offer further assistance once you are able to boot XP.  Overall however, looks like some ongoing hardware issues.

• What to do about CHKDSK message "volume appears to contain one or more unrecoverable problems".

  My XP Home just quit starting all along.  Previoously before leaving he would do a CHKDSK scan and then go over to start.  Now, it closes a few seconds after the Windows screen comes up with the dots that runs through.  The Windows image stays on the screen, but nothing else happens.  I put in my XP disk to run the repair and got at the C:\Windows prompt after all the various commands of the finish.  Then I typed CHKDSK and Enter.  The first time that CHKDSK has stopped 38% full.  The 2nd time it finished and gave me the error message: "volume appears to contain one or more unrecoverable problems".

  I sure would appreciate it if someone can suggest my next move to get XP running back?

  http://www.computerhope.com/issues/ch001214.htm Hope this helps, Gerry Cornell

• Speed problems according to the channel in which I connect - Possible hardware problem:

  Hello

  I bought a R8000 about 1 month, and it worked pretty well. Last week, I read a review on the router suggested what a turn on the Smart Connect. That's when the problems started.

  -Panda USB wireless that worked perfectly started to have speeds of 1.5 Mbps when my service is Comcast 150MBps explosion. Before turning on the S.C., it reaches that speed easily.

  -After the filming of Smart Connect, did not improve the performance of the USB dongle. It is remained at 1.5 Mbps to 3MBPs. I tried to fix it for a week now.

  -J' I reset the modem (button reset button for 10 seconds), configured my router again and added to my dongle is malfunctioning, the router started having trouble to detect my external WD "My passport".

  Today, troubleshooting the wireless dongle with Panda, I changed the channel 5 GHz at the elementary school and the speed is back to 170 Mbps. The router is kept at approximately 3 M from the computer without any obstacles between them.

  Finally, the streaming of my router (with cable) to my TV using DLNA sometimes stutters. yesterday, she even caused the TV to not recognize the transmitted file.

  Can you help me troubleshoot the router more far to find if it is defective?

  Thank you

  As I started the topic, I would give it a closure. My problem was that I had a USB Wireless Dongle of Panda, who performed in the secondary channel (high way) but ridiculously low in the primary (Channel Low). As I had Smart Connect lit, I couldn't control my connected computer channel and appeared the problem was with the router.

  That said, I noticed a better balance between devices when I disabled the dynamic QoS option. I don't know if the algorithm for dynamic QoS is simply wrong or its implementation by the current firmware (V1.0.3.4_1.1.2) is buggy.

  In any case, currently, everything works with me. Explosion of Comcast 150Mbps and rapid tests is between 157 to 153Mbps in tests using a channel 5 G.

• Sorting the rows in the table based on the first character - speed-problem

  Hello

  I have a text file with a lot of lines. The file is imported into LV, and must be sorted by the first character.

  It works very well, but gets very slow lines if too.

  If 40,000 lines then take 0. 2 s.

  If 400,000 lines then the time rises with factor 100 in 25 years.

  If 1,000,000 lines then the weather is dry 222 (~ 4 min)

  Attached is the code which sorts a table to text.

  The number of lines can be set with the meter of the loop (Loop-counter * 4 = NumberOfLines)

  The elapsed time is displayed.

  How to speed this up? (Or check the more linear time number of rows)

  Thank you

  

  You can try something like that. If you treat a table line by line, you end up taking a lot of time.

  

  Sorry I have a problem of fixing of the VI.

• Acquisition speed problem - cDAQ9188XT

  Hello

  I need your help because I have a slow acquisition problem in my project that I don't know how to solve.
  Basically, I realized that my program was not run fast enough and I found that it was because of my acquisition of dig vi.
  Acquisition rate / loop is limited to 772-773ms for each iteration, while I could at least 100ms.

  In order to reduce to a minimum the other task to do here is what I did:
  
  and what I get:

  

  For the results 2305.63... I had plugged nothing but values with wire are good, the problem is not there.

  I'm still very novice with DAQmx tasks (I wanted to learn to do without the DAQ Assistant, which itself puts ms 2800 loop...) so there may be some errors, but I don't know where...

  I acquire the temperature only a NI 9213 module that shouldn't have problems to keep! And I request a sample on request. (Clocked in the future by a loop of 100 ms between each iteration).

  To create the 'task' refnum, I converted my old DAQ assist in a task! Maybe it's here-> 2.0 assistant DAQ in the project
  I have also changed my computer, I get exactly the same result, so the problem comes from my code / configuration...

  The project is not executable because it took me a while loop in the sub acquisition.vi vi to identify the problem.

  The vi test is called test - speed.vi and the task refnum: assistant DAQ 2.0, be sure to select on the Panel before printing, although I doubt that without the same DAQ - module, execution starts ^^

  In addition, as a substitute in the whole project, the acquisition by simulation, it works almost perfectly!

  I hope that I was pretty, as usual, do not hesitate to tell me if I should explain more clearly!

  I can not find a solution at this time, do you have any idea?

  Thank you very much!

  Erwan

  PS: do not hesitate to criticize the bad things that you see in my project as a whole, if you see something really bad!

  PS2: I see just with a SINGLE temperature on the nor 9213 my loop is 163ms...
  

  Look at the specifications on page 6.  The 9213 has 2 modes, high resolution and high speed.  It also has an auto zero option.

  http://www.NI.com/PDF/manuals/374916a_02.PDF

  When you configure the task must be a device tab that has the auto zero and adc synchronization mode.  Change the synchronization in high speed mode and the auto zero times or none and see if that speeds up things for you.  But there is a take-off with precision.

  14 playback channels I received about a time of 300 ms iteration by using a task DAQmx.  I found that with the help of the 9188 some modules are not as fast as I would like.  You can run your thermocouples in a separate loop and transmit data to your main vi when it is available.

• WRT1900AC with internet speed problems

  So I've recently updated my 30mbps to 180mbps Comcast internet. We decided to get new hardware to support this faster speed that our 'old' was quite old. The old router is a Linksys E2000, not terribly old, but does support up to 300 Mbps. Our upgrade includes the WRT1900AC and a modem Arris Surfboard SB6183, both purchased about 3 months ago.

  Now here's my number: At the time when we thought that the new internet, router and modem seemed quick and we really didn't actually check our speeds are after you configure the settings. After about a month I started noticing the buffering in the videos and on the websites of loading time slower. I decided to perform a speed test on speedtest.net and found that the speed was down to what she was before us all, upgraded 30mbps... This is certainly not what I pay for...

  A crossed wireless settings to try various channels rather than just auto and got one that seems to work. Channel 11-2, 462 GHz on the 2.4 GHz network and channel 157 - 5.785 GHz on 5 Ghz. prioritization of media network also tried lit after reading that would solve the problem. He did it! I was getting around 150mbps down, so it was a big improvement. Awesome its fixed!

  I ignore the case for a few weeks, but later concluded that the internet was down to 35mbps. This confused me because I did not change settings either. I do more research and find how to configure bandwidth downstream under MP settings. He seemed to be attached to all about 30mbps so I upped it to 200 Mbit / s. save the settings, restart the router just to be sure and do a speed test. Nothing has changed. Always get a slower speed to about 35mbps down and 12 upwards.

  

  I tried everything I found on the internet with no results. To reset the router to factory settings to change the channel under network settings for each network. Still nothing. It fluctuated between 20-35mbps down with the settings I've adjusted and does not exceed 35. I don't know if there is a hidden buffer, I should be searching or if it's something else.

  If I'm missing any info in this I'm going to try my best to fill it.

  Any help is appreciated!

  Thank you

  Matthew

  Your bandwidth downstream MP must be set to 184320. Active WMM.

  To ensure that the issue is not the modem or ISP connect a computer directly to the ISP modem and run the speed test. Keep in mind that on your network the user could also heavily use the Internet causing the performance problem.

• Download speed problems

  recently upgraded to 30 MB with WiFi ISP and speedtest.net shows ok but cable running only at about 21MO. It is with Vista. In safe mode, it runs at 31 MB assume so must be a software problem. Have tried with Norton firewall off - no difference. Can anyone help?

  Hello

  Pass first down for driver update methods and update the interface NETWORK (wired) and the WiFi driver
  (Wireless).  Good idea to update the others at the same time. Also check the system manufacturer
  (Manufacturer of motherboard for custom systems) to update the BIOS and chipset of low level drivers.

  Check with the router manufacturer for firmware updates.
  
  ---------------------------------------------------------------

  After the pilot updatess use these methods:

  Use the startup clean and other methods to try to determine the cause of and eliminate problems.

  ---------------------------------------------------------------

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  ===================================
  ===================================

  And, if necessary:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Why is my Internet connection so slow?
  http://Windows.Microsoft.com/en-us/Windows-Vista/why-is-my-Internet-connection-so-slow

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Connection speed problems - black WUSB54GC usb adapter

  Hello everyone,

  This is my first post here!

  I googled nothing helped, and so I thought I would record with the Linksys forum and see if maybe I can solve this problem that others may have as well.

  I recently installed black WUSB54GC usb wireless adapter on my desktop PC, windows XP (now updated with service packs, etc.)

  The adapter receives the complete signal (very good - excellent, 54 Mbps), but it seems that my download speeds are capped with this adapter. Web pages same way load more slowly. I can place the macbook from my girlfriend directly next to my office, connected to exactly the same wireless network, and its download speed, browser speed and speed test results are always twice as me (any site speed test I use or what file I download).

  When I do a speed test, almost seems as if the speedometer needles few want to continue, but they just 'bounce', as they are hitting some kind of ceiling.

  When downloading files, the macbook on average 500 to 800 Kbps, while the adapter WUSB54GC hangs out at approximately 90 kbps.

  I have read in this forum and have adjusted my router Linksys WRT54G wireless suggested as follows:

  -Set the channel 11-2 wireless, 462 GHz

  -Change the interval of tag to 75

  -Change the Fragmentation threshold to 2304

  -Change the RTS threshold to 2304

  In addition, my connection speed is even slower, regardless if I have the settings TCP/IP (under the Wi - Fi connection properties) set manual (static ip) or automatically.

  Any help would be greatly appreciated, as I would like to be able to get this thing working properly, knowing that my router is pumping a lot more than this adapter is letting me use.

  Thank you!

  Well, I think I solved the problem.

  Seems that in some ports USB on my motherboard (Asus P5B) do not allow to run at full speed wireless USB adapter. I had used in the rear ports on my computer... but the passage for the first ports (that came with the case - Thermaltake Armor) seems to have solved the problem. However, as I believe that all of the USB ports I have is strange Hi-speed USB 2.0 and strange that those outside that came with the case and will connect to the pins on the motherboard works better than those actually built. Huh.

  Wouldn't be something to do with the drivers for the WUSB54GC, or is this a problem with USB port drivers?

  In any case, I'm sorry if this sounds like a useless thread now, but maybe this someone solve other problems too.

  See you soon!

• Windows Media Player playback speed problem - static...

  I play an MP3 to an audio book on WMP file and when I go on it 2 X normal playback speed, suddenly the sound produces a static noise. The audio is always readable, but static electricity is super annoying.

  Do you know what causes this and how to fix it?

  Thank you very much

  Thanks for the tips... I found actually an ideal solution that completely eliminated the problem...

  I previously converted the audio book in MP3 format, and as I said, I had that static when going above 2 X the playback speed.

  Well, what I did to solve the problem is the following:

  I used RealPlayer (which is a 100% free tool) to convert the MP3 to a Windows Media Audio file. Just click convert to button in RealPlayer and change the settings and press convert...

  AND'RE YOU READY TO GO...

  The audio is excellent... zero static... and now I can listen to the audio book of more than 2 X the normal speed in Windows Media Player and do with it in less time that I would otherwise...

  It's a beautiful thing!

  Wanted to leave instructions because other people have noticed that they have had this problem and I am sure that there will be more who need a solution in the future...

  Cool - let me know if you have any questions for those facing the same question...