Version number in "Application Properties" does not match what I put it in in 'Version' on JDE

Similar Questions

• Why do write can not be performed because the number of data channels does not match number of channels in the task.

  Possible reasons:

  Scripture cannot be performed because the number of data channels does not match number of channels in the task.

  When writing, provide data for all channels in the task. You can also change the task so that it contains the same number of channels as the written data.

  Number of job channels: 8
  Number of data channels: 1

  Lama says:

  The DAQmx vi writing gives me the error. If I run a single channel, isn't a problem. Multichannel gives me error.

  You are funny! Why tie yourself to work VI (single channel) instead of one that gives you errors (multichannel)?

  (If your car does not work, you bring car your wives to the mechanic, right!)

  What is the exact text in the multichannel 'physical channels' when you do the AO control?

  Lama says:

  I did a sequence to ensure that each function has been run in the correct order. Wouldn't a race condition.

  All you have to do is wire the 'start of task' error at the entrance of error of the DAQ assistant and then back to 'stop task' and things will run in order. Guaranteed! Think the stream! Everything else can run in parallel or the order is irrelevant.

  First convert the sequence stacked to a sequence of plate, remove the flat sequence and add the mentioned son. Now, do a "cleaning pattern.

  A when stacked with the inhabitants of the sequence is one of the worst construction you can possibly do. It makes the code difficult to follow, impossible to maintain, difficult to debug.

• 500 the application author does not match the author token of debugging

  My name is Jean-François Geyelin. My application name is PewPew.

  When you try to run PewPew on a playbook, I get the error "500 the Application author does not match debug token author.":

  the command deploy blackberry - installApp-password abdelkader 192.168.1.37 - package device-Debug/PewPew.bar returns:

  Info: Send request: install
  Info: Action: install
  Info: File size: 3575023
  Info: installation...
  Info: Treatment 3575023 bytes
  actual_dname:
  actual_id:
  actual_version:
  result::failure 500 the Application author does not match debug author token.

  I did check the following:

  the blackberry-nativepackager - listManifest PewPew.bar command returns (among others):

  Package-author: Jean-Francois Geyelin

  Package-author-Id: gYAAgPqb4i9DBQ-DjR0zWsAWK8s

  blackberry nativepackager - listManifest library/Research\ In\ Motion control / debugtoken1.bar returns (among others):

  Package-author: Jean-Francois Geyelin
  Package-author-Id: gYAAgPqb4i9DBQ-DjR0zWsAWK8s

  What should I check or what is the problem?

  
  

  Problem solved by clearing and forwarding of the token of the device debugging.

• Signature App, number of Folios error does not match the main file Folio

  Hi all;

  I have a standalone application of 250 pages that I'm trying to compile for the Apple Store. I've read through the forums and enabled "AppBuilderLoggingEnabled.cfg" in my home directory of the user to discuss the issue. Here is an excerpt of the newspaper which has been created which, to me, shows why the app is not signed.

  46386 codesign ERROR [main]. Signatory - failure during the signature

  java.lang.RuntimeException: invalid package, number of folios does not match the primary file (Folio.xml or Issue.xml) 251-250 folio

  at com.adobe.devtech.codesign.IPAOutputHelper.convertFolioProduceFormatToFolio (IPAOutputHelp er.java:272)

  at com.adobe.devtech.codesign.IPAOutputHelper.replacePlaceholderFolio (IPAOutputHelper.java:1 92)

  at com.adobe.devtech.codesign.IPAOutputHelper.execute(IPAOutputHelper.java:82)

  at com.adobe.devtech.codesign.Signer.sign(Signer.java:169)

  at com.adobe.devtech.codesign.Signer.processArgs(Signer.java:106)

  at com.adobe.devtech.codesign.Signer.main(Signer.java:46)

  46388 codesign ERROR [main]. Signatory - error: invalid package, number of folios does not match the master folio (Folio.xml or Issue.xml) 251-250

  I deleted special characters in the article titles and rebuilt the app only to deal with the same error. I have advanced and created a new AppID in the portal to Apple developers, created new files available, and the error remains. I am now to create a new folio and import the items into the new folio to see if that will solve the problem of "number of folios does not.

  Any help or idea would be amazing. Thanks to you all.

  -mat

  I created a new folio and all items imported again. After hitting "Create App" for this new folio, to about 10 pages in a 'PDF Export' error stopped the app creation process. I went in InDesign to update the layout for the 10 page to see that the PDF export issue kept me from updating the page layouts as well. Some thing in the InDesign file was not playing nice with the creation of folio, so I created two new InDesign files, deleted the article and built a new article from scratch. I was able to import the new page in a new article to the main folio and click on "Create App" again. This time he had no problems with the creative process. I have synced files available in App Builder and could sign the application code.

  I guess the moral of the story is to double and even triple check each item along the way to make sure there is no problem, is introduced into the process that eventually causes headaches during the phase of distribution of creating applications!

  -mat

• Size of the hard drive does not match, what to do?

  End of 2012, the MacBook Pro 13 "

  I've added everything I installed and registered on my macbook and it does not match the size of my disk info...
  I just deleted all the documents that I need to see what will happen with the size of the disk and it says: drive for 'other' size is 85GB and

  Audio = 0
  Film = 0
  Photo = 0
  Programs = 0
  Security Copies = 0
  Other = 85,17 GB

  And the strange thing is that I have 10 + adobe programs installed (that doesn't add anywhere near 85 GB!)
  But the weird thing ', it is also that it shows 0GB to programs/software that I obviously have a lot of programs/software installed. WHAAAT...

  It's really annoying

  It seems as if increases the amount of data in 'other' counts for

  Is there someone out there in the world of the internet, who knows how to fix this?

  I tried to read a previous debate about this, but to be honest, I do not understand...
  I'm not exactly a macbook-computer-expert when it comes to knowledge like that

  I would be grateful for your help!

  

  It is in Danish, but... Yes

  LYD Sound/Audio =
  Film = film
  Photo = Photo
  Progr. = Programs
  Sik.Kopier = security Copies
  Agent = other

• 881 failure: The Application author does not match debug author token

  Hey guys, I'm a newbie at software development and don't know anything about the other languages except HTML and CSS so I decided to try the apps program to see how it works and if it's the right think for me. I received my 'key' for the playbook and generated and download the Debug Token. My first idea was to put the Hello World app (that I copied on the BB site) on my playbook to see if everything works, but every time I try to download the app, I get "the application failure 881 author does not debug author token.

  I have tried a few troubleshooting myself (make another Debug Token, adding the and a blackbery - tablet.xml with these fields in the config.xml file and) and still nothing. Do you know the guy what is happening and what should I do to solve this problem, so I can download my apps on my playbook?

  Thank you

  Oskar

  There is an easier way... and maybe just an alternative.  I had this problem before and the reminder to change the bbwp.properties file to run.

  For more information, see this page:

  https://developer.BlackBerry.com/HTML5/documentation/runnning_unsigned_apps_using_a_debug_token_1866...

  Copied from this page:

  For PlayBook OS applications

  1. In the SDK BlackBerry WebWorks for BlackBerry Tablet OS installation folder, navigate to thebbwp\bin folder.
  2. Using a text editor, open the bbwp.properties file.
  3. Add the path to the file to debug token using the debug_token > tags.

     path to debug token file
     

  Example: file bbwp.properties with the path to the file debug token

  
  
  -quiet
  C:\Program Files\Research In Motion\BlackBerry WebWorks SDK for TabletOS 2.1.0\jre
  AirAppTemplates
  AirAppTemplates
  C:\Program Files\Research In Motion\BlackBerry WebWorks SDK for TabletOS 2.1.0\bbwp\blackberry-tablet-sdk
  ext
  C:\my_debug_token.bar
  
  

  You can now load your app on a debug-enabled BlackBerry device without having to sign

• Scripture cannot be performed because the number of data channels does not match number of channels in the task.

  My VI works as a motion detector.  Whenever the motion detector is activated, the led lights up and a beep is heard (a switch will exercise my motion sensor).  Once all the lights are on, the system reset is supposed to light up, and then the other three lights turn off back waiting to be activated once more.  My attachment saved as "sensor project", I have the VI working with data acquisition by implementing a case of random number, and the VI works here to give a demonstration of what I'm trying to work in favor. Any information would be greatly appreciated.

  You have some problems of logic and data flow.

  Once all three loops stop sensors, all outputs are necessarily true, then the case and a compound bow structure in the loop (reset) next is useless. Because the boolean in the fourth loop ending is immediately true, the loop to stop and not care about the State of the reset button. Maybe you should connect the termination condition to the wire going to the system reset light instead. Since it is also a polling loop, it needs a small wait. Once you press reset, the VI full and stops. (Do not use the continuous operation mode!).

  Solution: Create a state machine with a single outer loop. You have 4 x code too!

• Current version of Flash listed does not match what is downloaded

  I see Adobe Flash 16.0.0.287 is available here: http://www.adobe.com/products/flashplayer/distribution3.html

  The version I downloaded is always 16.0.0.257

  Difficulty please!

  Thank you.

  Thank you to provide the location.  I'm going to climb it.

  --

  Maria

• The number of photos in a folder does not match what appears in the display of the grid.

  

  It shows pictures of 1907 in the left tab in the grid view, it displays only the 1886 photos in the grid view, but no filters are on. Where are the other 21 pictures?

  Try using the command

  -> Photo-stacking > expand all stacks

• For my preview of the PSD in excerpt does not match what I see in Photoshop?

  EXTRACT

  

  PSD

  

  the problem is resolved is that there is sRGB is RGB.

• My online page is does not match what I have in DW

  Hello

  This is my first real effort on an Internet site: http://wisercharitable.org/vr_index.html

  In recent months, she looked very well, but I've added a page here and there in the last week or two and something turned out badly.  It has something to do with the size of the font, because when I go online, it's huge compared to what it looks like in DW.  In fact, he cannot even sit properly on the page.  Also, it seems to have an effect on each page, leading me to believe that the problem is on the style sheet.  I'm sure it happened because of a change, I did recently, but I can't understand what would be and why the pages all look good in DW.  Any thoughts would be appreciated as I learn I will.

  Here's my CSS code as well:

  @charset "utf-8";

  / * CSS document * /.

  {body

  background-color: #000;

  }

  #container {}

  height: 1200px;

  Width: 900px;

  left: auto;

  right: auto;

  background-image: url(Images/vr_grad.jpg);

  margin: 0 auto;

  }

  #header {}

  Width: 878px;

  height: 130px;

  background: #FFFFFF;

  background-image: url(Images/vr_header.jpg);

  border: 1px solid #000000;

  padding: 10px 10px 10px 10px;

  }

  #date {}

  Width: 880px;

  height: 20px;

  background-image: url(Images/vr_redgrad2.jpg);

  border: 1px solid #000000;

  padding: 10px 10px 10px 10px;

  text-align: center;

  do-family: Georgia, "Times New Roman", Times, serif;

  font size: 20px;

  make-weight: bold;

  }

  {#left_column}

  Width: 150px;

  height: 864px;

  float: left;

  margin: 5px 5px 0 0;

  border: 1px solid #000000;

  padding: 10px 10px 10px 10px;

  text-align: center;

  font size: 20px;

  make-weight: bold;

  background-image: url(Images/vr_yellowgrad.jpg);

  }

  {#center_column}

  Width: 890px;

  height: 936px;

  margin: 5px 5px 5px 0;

  padding-right: 10px;

  do-size: 18px;

  make-weight: bold;

  }

  #center_column h2 {}

  do-size: 36px;

  make-style: italic;

  }

  {p}

  margin: 0;

  make-weight: bold;

  Color: #000;

  }

  #footer {}

  Width: 880px;

  height: 80px;

  border: 1px solid #000000;

  padding: 10px 10px 10px 10px;

  background-image: url(Images/vr_grad.jpg);

  do-size: 14px;

  do-family: Georgia, "Times New Roman", Times, serif;

  text-align: center;

  Police-weight: 100;

  }

  .links {}

  font size: 24 PX.

  }

  . Events {}

  font size: 24 PX.

  }

  {.floatright}

  float: right;

  margin-left: 5px;

  margin-top: 10px;

  }

  {.floatleft}

  float: left;

  right margin: 5px;

  margin-bottom: 5px;

  }

  . GFR {}

  font size: 20px;

  color: #CC9900;

  }

  . GFR {}

  Color: #000;

  do-size: 18px;

  }

  . GFR {}

  do-size: 18px;

  }

  #container #center_column .ms_title {}

  make-weight: normal;

  do-size: 18px;

  }

  . {Sharp

  make-weight: bold;

  }

  . Bold {}

  do-size: 18px;

  make-weight: bolder;

  }

  {.spon}

  make-weight: bold;

  }

  Thanks for any help you all can offer.

  Chris

  Jon,

  It actually worked.  In Design view, it looks bad, but when I went to the live mode it looks great.  It is downloaded now and it looks good.  Thanks for the help.

  Chris

• Reinstall all the software on the new hard disk, Acrobat downloaded in the history of the order and he said the serial number does not match

  I just had to restore my computer from scratch.  I have redownloaded XI of Acrobat Standard of my history page to control on Adobe's Web site with serial number in my order history page.

  It gives me the error that the serial number is valid, but does not match the software on the computer.  He invites me to select another but Acrobat Standard XI isn't in the drop-down list.  I tried everything in the list and he said that they do not match.

  How is that possible?  What should I do?

  I recognize the problem you describe. Simply, you install an upgrade. The product "calling" it asks for is the OLDER version of Acrobat that gives you right to the upgrade. You must now enter your serial number for Acrobat X or 9, to prove eligibility.

• author of the 881 failure application does not match the author token of debugging

  Hello

  I can't launch my app Android of Eclipse for the BlackBerry PlayBook.

  Error:

  Impossible to deploy the project MYPROJECT
  Info: Send request: install
  Info: Action: install
  Info: File size: 1076852
  Info: installation...
  Info: Treatment 1076852 bytes
  actual_dname:
  actual_id:
  actual_version:
  result::failure 881 the application author does not match the author token of debugging

  Thank you

  Delete the special character of the author fixed the issue.

• video copied to DVD does not match project that I can see

  Good,

  No doubt another basic question, but I can't find an answer in the Adobe manual. I just discovered (after burning 8 copies of the same file) that the film on the DVD does not match what I see on the screen of project. The drop-down list to organize > project resembles what I want except that he seems to have the original avi file that I edited later as well as the changed file. The timeline seems correct. The timeline seems correct. I tried to eliminate the 'markers', but there was none to remove - the drop down menu gave me the ability to add markers. A Council, is that the DVD is picking up a model of menu that I played with, but could not get to work and then deleted. I ended up using the title screen very basic with black video in the high title of range drop-down list menu rather than the option model to change. I see the new title in the scene and timelines. Yet once the previous question just posted, I don't see anything in the screen clip
  (e.g., boxes of th) under 'organize '. In addition, the video clip on the DVD appears truncated by about half of playing time.

  At one point I have only the old menu design clip shows just below the montor screen could display but could not know how to remove.

  THX

  Yes, I want to.

  To preview your created disc, click the Preview button on the monitor of the disk layout.

• Player version listed in the GUI does not match that of the executable file (new)

  I've posted about this before (http://forums.adobe.com/message/4817948), but has never been able to find an answer.

  I am currently deployment of Adobe Reader versions 10.1.5 using the MSI installer and group policy. The problem is that a user stops his midway to Windows 7 computer while installation MSI interrupt (i.e. screwing) installation process. I had to remove some entries from the registry and restart the PC of the user in order to restart the installation of the reader (something I've done in the past).

  To verify that the drive has been installed successfully, I navigate to the Reader (AcroRd32.exe) executable Program Files, double-click the executable, select on Adobe on the Help menu, check the version number in the info box and see that the version number is 10.1.4 (i.e. the old version that I'm upgrading to). However, when I travel to the Reader (AcroRd32.exe) executable in Program Files and and open the properties of the file, I see the version 10.1.5 (i.e. the new version I am upgrading to).

  So the Player version listed in the GUI does not match that specified in the executable box.

  It's the second time that this has happened with a Windows 7 PC. I've never known this kind of thing with a PC running Windows XP.

  Why is the different version number in the GUI? Where the version number read to leave for the GUI? The registry? Anyone can shed some light on this situation?

  Hi Grittyminder,

  Remove some reg entries is not going to give you clean uninstall if you pouvez get a viable product. You can run this to get a better result: http://labs.adobe.com/downloads/acrobatcleaner.html.

  While I don't know what the problem is, it would be interesting to check the version of the product using the MSI API as described in the guide of the administrator to the www.adobe.com/go/acrobatetk.

  Ben