"VISA read text strings do not match identical constants text search - could it be double-byte characters.

Similar Questions

• The value read by visa read that VI is not correct!

  I design a labview program to control the Agilent E5072C Network Analyzer. When I want to get the value of this instrument, I use VI "VISA read" listed in the plate. However, the value read from this VI's latest measurement of time value. For example, the last time that the read value is 1.0 db, and this time the measurement value is 1.2 db. But when I use 'VISA read' VI to extract the value is 1.0 db.

  Agilent also provide a VI for this device to read the measurement value and she was always correct value. If someone could tell me why? need to do any action before the value read from this instrument if I want to use VI "VISA reading" instead of Agilent VI?

  You are probably reading too quickly.  Reading it in NOR-MAX, you do it by hand, it takes more time.  When you do that programmatically, it is "instant".  Try using the * OPC? command to activate your order in a query.  He returned then a '1' in the buffer.  Read the '1' and then create the command fetch.

  For Dennis:

  I've had bad experiences with the drivers provided by the manufacturer to the point where I don't even try to use more.  But Agilent is also anal about their drivers, because they are on their books, they should pose no problems.

• When I use it; (semicolon), the character string, do not indent!

  Suppose that we have any string of characters within a text block:

  asldfjalksdjflkajsfdklasfd

  If the string does not match inside the text block and the setting is checked in the paragraph Panel, will the string for examples:

  asldfjalk-

  sdjflkajs-

  fdklasfd

  Now suppose this character string inside, there are; (semicolon):

  asldfjalk; sdjflkajsfdklasfd

  now on the string do not hyphen, if the text block is too small, it disappears and a red sign as usual appears at the bottom right of the text frame. So I have to enlarge the text block to display the entire string of characters and, if the block of text outside the borders of the page?

  Can someone help me solve this problem?

  Hi Henry,.

  How many times this will happen with the copy that you have?

  If it's only an opportunity, then you can simply insert newline forced according to the needs.

  You put in a jump line by placing the cursor where you want to pause, and pressing SHIFT + return.

  In addition, if cannot see the text because of the long string (all see you is the Red sign on the block of text), select the block of text and press ctrl-y (cmd - y on mac) to open the copy in the story editor. Insert the line break, if necessary, and the copy will appear in the text frame.

  I hope this helps!

  See you soon,.

  ~ Nate

• County to return read VISA does not match number of bytes

  I encounter an error with a VISA reading.  I ask 8 bytes (in number of bytes), but get only 7 return (return number), which causes errors in my code downstream.  Curiously, the VISA Read block does not return an error.  Any ideas on how to debug this?

  Data sheet:

  LabVIEW RT 8.2

  VISA 4.3

  Series OR 3.3.0

  PXI-8431/4

  Parameters: 1843200 Baud, 8N1.

  Is VISA reading set to put an end to the reception of a termination character?  I think that it does not have the stop in the output string character, which could make your short back counter.

  Lynn

• VISA read lose characters beyond the end of the output string

  Hello

  I wrote a VI to take a string of output data of an ardunio Uno and analysand. I use the vi read Visa to enter the output channel of the unit. In the end I will connect a device that actually gives the value in this type of format string: (#80212164,2289,2292,2296,2300,2328,2289,2297,2290,2300,2308,2292,2295,2298,2289,22,24,0 *).

  So after a large number of loops, the program starts to drop the last characters of the string that it generates. If the string of Visa Read output reads something like (#80212164,2289,2292,2296,2300,2328,2289,2297,2290,2300,2308,2292,2295,2298,2289,22,24,). The only way to solve this problem, once it has occurred must completely close labview (completely). Once I open again and start the program running, all is well in the world.

  Has anyone had this problem? I tried to debug it in different ways and the only weird symptom I have other Visa Read function lose a few characters of the string is the fact that by looking at the bytes to the Port after I read visa, is that she starts showing five bytes instead of zero.

  my last attempt at resolving this issue is attached.

  Note: The Ardunio outputs a string of this format every 2 seconds with the values being incrimental on a specified range. (80212164,2289,2292,2296,2300,2328,2289,2297,2290,2300,2308,2292,2295,2298,2289,22,24,0 # *)

  You can configure the * your character of termination if your Arduino does not send the carriage return or line feed.  Use the configure a Serial Port to ensure that your settings are correct.  You can also use this VI to increase your timeout so that you no longer need your waiting.

• The text of the e-mail under the column of the object does not match the selection

  When I get to my Inbox and select an e-mail to open the middle box and the text box below do not match the selection in the object column. This has occurred recently and only on my laptop. My office works fine. The central area and the text matching, this email has been deleted but the text won't just change and go. I'm going on a trip tomorrow, and if I can't fix this, I won't be able to open emails with possible solutions. I'll see answers but can't open them.

  right click on the folder, select Properties, and then on the button repair.

• The VISA read function is not read the bytes specified in the buffer zone

  I created a program that continuously acquire data of the inverter. But, the "Reading of VISA" function is not rreading all bytes of the buffer, which is a big problem because the way my work programme is it will extract the specific buffer bytes and convert these values in voltage and current values.

  I specified the number of bytes that I want to read the buffer as for example I want to read 21 bytes. But, even if there are 21 bytes in the buffer, the read function VISA read only 9 bytes. Im not using any character of endpoints so this is weird. I'm using LabVIEW 2011.

  Is attached a photo of my program and the results.

  You still have the active stop character.  You must connect up to a FAKE at the entrance of termination character activate on the Serial Port to set it up.

• These can be wired together as their data types (digital, string, array, cluster, etc.) do not match.

  Hi, I get an error update LabVIEW 8.2 for 2011:

  These can be wired together as their data types (digital, string, array, cluster, etc.) do not match. View the contextual help window to find out what type of data is required.
  The type of the source is cluster of 2 elements.
  The type of the sink is typedef "IMAQ Image.ctl"
  IMAQImage (IMAQImage,).

  This type of incorrect argument can be caused by an old instance of the Image data type.
  To fix, simply replace the instance with the definition of type IMAQ Image.ctl in the control menu of the image palette.

  The source is:

  Call library function node - image (dup)

  The sink is:

  IMAQ_array for image - image

  I tried to delete the image VI IMAQ_array & always replacing but it connects...

  Here is a picture of the VI, I have a number of VI to update and they all have this problem

  Home is also the VI.

  See if you can shed some light on this

  

  The solution, he had to do with the representation of images in the old and the version of Labview

  I'm completely new to NI Vision, so I had no idea what I was looking for

  from this thread:

  http://forums.NI.com/NI/board/message?board.ID=200&message.ID=5849#M5849

• the channel guide does not match the actual string

  the channel guide does not match the actual string that is to say PBS should be Channel 13 but is listed as channel 2 on the guide

  Hello James,.

  Welcome to the community of Sony.

  What is the model # of the TV?

  You can locate the model # of the TV from this link.

  You can try the steps mentioned on the underside of the base article of knowledge:

  http://www.KB.Sony.com/selfservice/documentLink.do?externalId=C408137

  Please mark it as "acceptable Solution" If you find this information useful.

  Kind regards

  Colby

• Leak memory in real time caused by VISA Read and timed loop of data nodes? Is not supposed.

  In collaboration with LV 8.2.1 in real time to develop applications that monitor or emulate computers on bus RS-422.   The following screenshots have been taken an application that monitors a transmission of 200 Hz.  After a few hours, the PXI station would break a range impressive messages angry... most involving something about memory loss.  After much hair pulling and passing money, my partner has discovered while looking at the available memory on the controller of loss of memory occurred at each loop containing a VISA read and propagation of error using the data nodes (see Leak.jpg of memory).  He concluded that if he went to the propagation of the error to the regular old shift registers, then the available memory was rock-solid.  (has the Leak.jpg of No memory)

  Any ideas of what could be the cause?  Do you see not any problem with the way that we code these kinds of loops?  We always strive to optimize the way in which we use the memory on our urgent requests and VISA readings and DAQmx bed give us the heartache more than ever, we are able to allocate memory for these screws some tips?

  Dan Marlow

  GDLS

  Hi thisisnotadream,

  This problem has been reported, and you seem to be exactly reproduce the conditions required to see this problem. This was reported to R & D (# 134314) for further investigations. There are several possible solutions, of which one is the one you have already found the wiring error directly in the loop. Other situations which give rise to no memory leak are:

  1 if the bytes of the property node port is not there and has read lies in each iteration and time-outs resulting are ignored.

  2. If the structure of the deal is gone and just blindly check the bytes to the port and read each iteration.

  3. If the timed loop is transformed into a while loop.

  Thanks for the comments!

  Kind regards

  Stephen S.

• all the pages that load do not match the screen have to scroll on the side to side to read

  all the pages that load do not match the screen have to scroll on the side to side to read

  all the pages that load do not match the screen have to scroll on the side to side to read

  =================================
  Try the following...

  View / Zoom... reduce the percentage

  The Zoom option can also be accessed from
  your at the bottom status bar.

  John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - to proceed at your own risk

• Windows 7 Narrator does not read text

  I can't get the Narrator to read text in the body of a Microsoft Word document (or any document - pdf, Web page, etc.)

  I tried to use all the commands Insert (both with the text highlighted and highlighted text), and they all say "BLANK DOCUMENT"

  The only thing he reads is "1 - Microsoft Word Document" and then he describes the menu options.

  FYI - I also posted this question in the forum "Desktop and personalization" - I cannot say what forum would be better.

  This message suggests a possible bug with Word, the solution is to copy the text in Notepad and read from there.

  Narrator using Vista with Word 2007
  http://www.Vistaheads.com/forums/Microsoft-public-Windows-Vista-General/17579-using-Vista-Narrator-Word-2007-a.html

  Choose which text reads reciting aloud
  http://windowshelp.Microsoft.com/Windows/en-us/help/13d48403-fb32-4f26-8141-2cf2ae72a4e31033.mspx

  http://www.Google.com/search?hl=en&RLS=com.Microsoft%3A * & q = Use + Narrator + in + % 2Bvista & btnG = Search Word

  Narrator can be a little buggy fixed, or just not up to par, because I can't read in Word on Windows 7, either.

• Director of Windows won't start; How to fix error: "component identity found in manifest does not match the identity of the requested component»

  Whenever I try to start Windows Movie Maker, I get the following error:

  "Sorry, cannot start Windows movie maker. Make sure your satisfied computer minimum system requirements before you try to start the Movie Maker and then try to update the driver for your video card if Movie Maker does not start".

  I know that my computer meets the minimum system requirements because it came with the whole package. I've also updated my video driver correctly several times. I even uninstalled Movie Maker, re-installed. Even uninstalled the complete set of Windows Live and re-installed, but it still does not work. After a lot of searching for answers, I found the event log in which this error:

  «Activation context generation failed for "C:\Program Files (x 86) \Windows Gallery\MovieMaker.Exe".» Manifest error or policy of the folder "C:\Program Files (x 86)" \Windows Live\Photo Gallery\WLMFDS. "." DLL"on line 8. Component identity found in manifest does not match the identity of the requested component. Reference is WLMFDS, processorArchitecture = "AMD64", type = "win32", version = "1.0.0.1". Definition is WLMFDS, processorArchitecture = "x 86", type = "win32", version = "1.0.0.1". Use sxstrace.exe for detailed diagnosis. »

  I don't know, but I think it's causing my movie maker does not start. I looked around even more of an answer to this question on how to resolve this error, and I couldn't find anything so far. Microsoft support said that I have nothing to do and it will solve automatically. Alas, I got this error whenever I tried to open Movie Maker (the time is equal to the time I tried to open it).

  What can I do to fix this?

  Thanks in advance.

  Hello JurrianH,

  You can go ahead and post in the forums alive in dealing with the problem with Live Movie Maker specifically. Please do not hesitate to answer, in the case where you are facing in the future other problems with Windows.

• TO_DATETIME gives the error ORA-01861: literal does not match the format string

  When I use the following in a formula in the column in the business model, the administration of BI tool does not complain:

  TO_DATETIME (LEFT ("registration - College". "D time". " ("' Exercise ', 4) | ("/ 09/01 ', ' yyyy/mm/dd')

  But when I use it in an analysis, I get the error message:

  ORA-01861: literal does not match the format to the call of the OIC string

  The scope of practice is a varchar of 6 characters (e.g. 201213), so I do not know what causes this error. Is this because the TO_DATETIME expects something like hh as argument?

  Without the element that to_datetime is supposed to work, here is an example that I made on SampleApp406.

  

  Try to add the "time", but for me it has always worked without problem.

• Error "ORA-01861: literal does not match the format ORA-06512 string.

  Hello
  I am getting error on EBS page when I click on the button
  
  I wrote the code in CO to insert values in table when the button is clicked
  
  but when I click the button it gives an error
  

  ORA-01861: literal does not match the format ORA-06512 string

  I think that his error of date format
  
  but I tried many styles of formatting but not yet able to fix it

  KAO

  You are right, that this is due to the error in the data type. Share the code that you have coded for button click here.

  Kind regards
  GYAN