Vista HP1100 HP 1100

Similar Questions

• Is there a vista for my HP Deskjet 1100 printer driver?

  I want to install my printer HP Deskjet 1100 on my new computer "vista".  Where can I find a driver?

  Thanx

  Jeroen

  Vista has included drivers for the Deskjet 1120, 1125 and 1000.  I'll try these drivers (in that order).

  Kind regards
  

  Bob Headrick, Microsoft MVP printing and imaging

• Printer Laser Jet HP 1100 and Vista

  Someone managed using a jet of HP1100A laser with the Vista operating system? I had to work for a short period, but then just stoped printing. I used an adapter cable to match the printer to a USB port. I then installed a card to the computer's parallel port. Still no luck printing. I can plug the 1100A to a computer with XP and it works very well. Vista does not recognize the 1100A. I had a neighbor who is a computer programmer and the computer does not communicate with the printer, he said. He tried to use several different drivers on the HP site, tried to use the disc that came with the printer, all this without success.

  Here is the page I was looking for:

  http://support.HP.com/us-en/document/c00867904

  I have configured my 1100 as a 1000.  If you follow the instructions, this should take care of it.  I don't know if I've lost any functionality, but I don't know that I am now using my Business Inkjet 1100 as expected with Vista even though HP says that this model is not supported under Vista 64-bit.  I'm very much a happy camper now.  I don't know whether or not it is the printer that you were talking about.  Good luck.

• Driver for hp business inkjet 1100 Series, Windows Vista home Premium x 64

  I recently bought a Dell Studio XPS laptop 1640. It has Windows Vista Home Premium x 64 operating system. My hp business inkjet 1100 printer series will not be installed with the hp installation CD. I need the correct driver. Apparently, hp does not offer one for Vista x 64. Is there a generic driver available that will do the work?

  HP provides the drivers for their products, not Microsoft.

  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=en&cc=us&DocName=c00867904

  I'm sorry, but the above is the info provided by HP.
  Try the info provided by HP. as their workaround, the link above.

  If HP does not write drivers for their product, you're out of luck.

  See you soon.

  Mick Murphy - Microsoft partner

• HP Laserjet 1100 with Vista

  I would like to printer announces an my computer HP vista laptop. He installed the USB to parallel port. However, I can't find the right driver. Laser Jet 1100 MS, but it does not work. What is the correct driver to use with Vista?  Can U help?

  Hello

  HP Laserjet 1100 is not a model number, a serial number of the printer.

  Select your correct link here HP model number, and follow it however to find if there are Vista drivers available.

  http://WWW8.HP.com/us/en/support-drivers.html

  4 matches found. Please select one below
  HP LaserJet 1100 printer series

  • HP LaserJet 1100 to printer
  • HP LaserJet 1100 printer xi

  HP LaserJet 1100-All - in - One Printer series

  • HP LaserJet 1100 A is all-in - One Printer
  • HP LaserJet 1100 has xi all-in - One Printer

  See you soon.

• Recovery creator disc error code: 1100 8-48-00000002. Satellite Pro L300-15

  Hi all.

  Satellite Pro L300-152 of the Vista 32 SP2.

  This laptop was gave me to try to repair (another instance of stolen suicide Vista).
  After retrieving the system (no re - install wasn't necessary), I would like to create a disc of recovery for the owner.

  However, when I try to run the "Toshiba Recovery Disk Creator", I get an 'Error' window with the following message is displayed "an unexpected error has occurred. Exit this application and start it again. (Error code: 1100 00000002-48-8). Of course restarting the application generates another identical message.
  No one knows what could be the cause of this error and how do I create a recovery for this notebook drive.

  Take care of all.

  Mike

  Hello

  This error message usually appears because the non compatible CD or DVD.
  I think you should first check if there is an ODD firmware update.
  On the Toshiba European page driver you might find updates firmware for different CD/DVD drives.

  You should check your CD/DVD drive and a compatible firmware is available, then you need to update this
  If there is no update firmware, then you must try different discs from different manufacturers to create a recovery disk.

• No sound HDMI on dv6t-1100 CTO

  I have a laptop dv6t-1100 CTO Entertainment. When I bought it, it is installed with Windows Vista. Then, I was able to connect it to my home theater HDMI system by simply choosing the HDMI output. Since I upgraded to Windows 7, when I attach the HDMI cable, the image is on the TV, but the sound is still coming through the computer speakers. My sound is IDT HD sound. I opened the settings to change the HDMI Audio output, but only the following choices;  Speakers and headphones double (default), headphones double independent and SPDIF (digital output HP dock screws). I tried to change the default to the last with no difference. I think I have the latest driver installed. Please help, as I want to connect the laptop to my home theater system to run a special program vacation I. Any help would be greatly appreciated.

  It worked! Thank you, David.

• On DX11 and Vista

  I was wondering if there will be an update for Vista DX11... because I've already spent $1100 on update of my hardware including an ATI HD5870 DX11 card... im short money for a while and do not know if the patient is able to get Windows 7 for a while...

  There are a lot of rumors out there, but people say those are false... .so I wanted to know if anyone knows a good answer...

  I really hope that its not another exclusive thing of the OS like Vista DX10...

  Hello BES12000, welcome.

  I guess that he gets out, very probably a month or so after windows 7 release.

  Have a look here:
  http://tech-mania.com/2009/03/download-DirectX-11-for-Windows7-Vista/

  Hope this helps,

  Thank you!

• recovery disk for HP Notebook HI 18 premium with windows vista 64 final

  Hello. A few days ago I had a flash media player update icon/box appear and I chose to download it. Since that time my thing has stop working... no printing, Internet keeps closing - I get a security warning that says I don't have permission to download the file (I was not trying to download a file). I ran Norton, Avira, bytes of Mal-ware and CC cleaner and no viruses can be found. I also get a "disk use raised by COM surrogate mother.  Looking at the configuration of my system files, I noticed that the COM + application is checked to run but shows, he stopped. I rebooted, restarted in afe mode...  Thus,.

  1. I thought that I orderd recovery disks when I bought this machine. I found a package of seled disks but cannot tell if they are for this machine or not. The label on the software: hp notebook pc F4665 - 12058A ze5000 WXP he edition

  2. If this isn't the software where I can get it and based on what I mentioned that going to work?

  3 info machine: HP HDX 18 laptop;  MS Windows Vista Ultimate Edition; 64-bit SP2; Intel Core 2 DUO CPU T9400 @2.53 GHz 4.0 GB RAM;  The label on the back of the machine: product: HPHDX18 p/n: FJ927AV the rest of the tag is within reach to make any other determinations.

  Also, in safe mode I don't have security alerts and other messages that I mentioned. I ran CCcleaner in safe mode and I guess I made a big Boo-Boo. Now I see even no internet...

  Please help if you can...

  "F4665 - 12058A ze5000 WXP he edition ' is that a Windows XP Home HP Recovery set for a laptop of HP ze5000 series. It will not work on your computer.

  Please see third-party provider computersurgeons.com to buy "Recovery Kit 514200-001 for HP model number X18t-1100. This software should work as it is a copy of the original HP software.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Upgrade Vista 32-bit, Vista 64-bit

  I recently "inherited" an Acer Aspire 5100 TravelMate a member of the family.  I had a lot of luck with Acer laptops in the past, so I thought I couldn't go wrong with this one.  So far, so good (great, actually).

  My question/quandry: this system came originally with the 32-bit version of Windows Vista.  For many reasons, I did a clean install with Vista Ultimate 64-bit upgrade.  Rockin '!  However, there are at least two relatively minor problems that I can't find solutions to the.  FIRST: the integrated mouse pads.  I can't turn it off when a USB mouse is detected as I can't find the drivers and Synaptics software for this computer only for the 64 bit version of Windows Vista.  Any suggestions?  SECOND: the ATI xpress 1100 graphic card flake.  Same problem as with the built-in mouse pad.  Once again, any suggestions?

  No mspot, here will be fine

  The symptoms you describe sounds more like a hardware problem, or the graphics chip or motherboard. It is not likely to be the the BIOS update - usually your laptop would not start!

• Blue screen after installing pentium D 960 on windows vista

  I recently bought a pentium D 960 on Ebay. It works very well for a while, then I get a blue screen Page_fault_in_nonpaged_area. My computer is a compaq presario sr2163wm. Compaq said that the processor should work. I don't think that the processor is bad because I ran it on the same machine with linux Ultimate Edition 3.0 for 3 days straight without any problems.  also had a blue screen which says something about an incorrect header? I had problems with windows stop but not the material, before I installed the processor. I just reinstalled windows with source material (the only way to really install windows with a recovery cd). One last thing, I use a Galaxy Geforce GT 520 to 810 MHz and 2048 MB of DDR3. system has 2 GB of DDR2 ram. chipset is a xpress 1100 ATI (northbridge and sb600 southbridge. 4 mb. bios RC415 latest revision 2008 5.34 (5.3 something) metagrads, Inc. of vista sp2 fully updated home base.)

  The combination seems to be OK, based on the specifications of the motherboard.

  You can contact HP about the problem you are having and see if any similar problem has been reported with the Pentium D 960.

• Windows Vista Ultimate Edition started cutting the computer when certain usb devices are connected

  I had this platform for a few years with no problems. Last week when I went to sync an ipod (which I had already done several times) it abruptly shuts. I can it restarts, but when I try to sync the ipod, same thing happens, no error message full closed.  Also, I noticed that when I am attaching other devices such as an external hard drive or a blackberry it stops.  Today, he does even without fixing anything. All of these devices were working very well.  I have disassembled the computer, cleaned all fans, removed all dust bunnies. I have an ASUS MB, cpu temperature seems good. I think it's a software/driver problem. The thing is I have not installed anything, System Restore does nothing, all the usb drivers say they are up-to-date. All USB ports are affected, even most directly on the MB.  Anyone had this happen?  I think buying windows 7 and try it because I don't want to replace the motherboard, I spent $$ on this a few years ago, raid, etc. of liquid cooling.

  It should last me awhile longer, last year the food out crapped (dust bunnies blocked fan), I replaced with a 1100 watt tagan. This system had worked great for a year, so I don't think it's a matter of P/S.

  Any help or advice would be greatly appreciated!

  Hi Highrever,

  1. do you have the latest Vista service pack installed on the computer?

  You can try to uninstall and reinstall the complete USB hub drivers and check.

  a. Click Start and typedevmgmt.msc and then click OK. Device Manager opens.

  b. expand Bus USB controllers.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer.

  You can also check if you get special material related errors in Event Viewer about what is causing the problem.

  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to restore Vista recovery Partiton? Help, please

  I bought the HP Pavilion dv6z-1100 CTO Entertainment Notebook PC with installed OS Vista Home Premium (32 bit).

  There are recovery Partiton (drive D). I have not at any drive recovery. There were a few errors in the operating system later and I installed some other cd of vista vista. I got to the recovery partition. Now I want to restore vista recovery partiton present on my hard drive. I run the System Restore Wizard, but there is no option to restore the D drive system. It gives only the option restore from restorepoint. Please tell me how to restore from recovery partation. Best regards

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, with HP you will need to press F11 at startup to start the recovery process...

  See you soon.

  Mick Murphy - Microsoft partner

• ATI radeon x 1100 does not not in win7 (32 bit) HELP!

  Hi all, I have recently updated for Win 7 (HP) and it does not recognize my graphics card. Win7 detects a "standard vga adapter" and not the ATI Radeon Xpress 1100 which is actually there (and has worked with Vista). I tried to download and install the driver vista for it, but he won't do it for me. The stabdard VGA card is that it will detect.

  I have a little technical sense and can operate normally these things, but in this case I'm just going around in circles. I searched every forum out there, and although there seems to be some suggestions, I have not found a solution. Basically, I want just a step by step procedure to get my Radeon x 1100 work in Windows 7.

  Can anyone help?

  Thanks in advance,
  McB.

  p.s. Sorry - I have a laptop Asus X50RL, running Windows 7 32 bit.

  The Windows 7 solution involves Asus publishes a full range of Windows 7 drivers, which one would be for the video. Did you ask Asus if they're going to do this? What did say?

  The current solution to "the video to work as it should" leads back to the original operating system...   Mike Hall MVP - Windows Desktop Experience http://msmvps.com/blogs/mikehall/

• Problems with HP LaserJet 1100 print printer windows 7 (64)

  I have a LaserJet 1100 HP printer and I bougt the printer cable USB/Minicent garage and reconnected the PC in an operating system of Windows 7 (64), Theplug and game need not recognize the PC and try to install it that way is suggested in the HP site but I got going in circles throuught pahges without success. Finally I found a diver and it installled hav it, but I have a question: in the Pinters loaded appears and HP 950 IEEE1284 controller and the HP Laserjet 1100, I tried to delete this 950aand HP cannot be

  I watched the HP1100 installed printer and I saw all my documents in the what... I removed most of the ten but one a test page and can not move and does not alow the printer to print correctly.  I went to another site and gave to Ms. driver and I installed it and now the shoewn of the printer are LaseJet HP1100 LaserJet HP1100 (MS).

  Once again in the default printer, the HP 100 when the test page has been sent is always stuck in Quebec and can'tdelete or print.

  I made the default LaserJet HP 1100 (MS) and sent a test page and print it.

  The question is which printer can I leave the HP 1100 as defauly the (delete or leave) or the HP LS 1100 (MS)?

  Has anyone had this problem before?

  Any s suggestion comment I appreciate them. Thank you

  Clearly your message not being your comments on the web site of Microsoft Answers, then I have it to this forum the forum of 'Hardware and drivers' Windows 7.

  Visit the page of your printer on the guide of the Microsoft Windows 7 compatibility for your printer here: http://www.microsoft.com/windows/compatibility/windows-7/en-us/Details.aspx?type=Hardware&p=HP%20LaserJet%201100%20Laser%20Printer&v=HP&uid=C4224A&l=en-US&pf=0&pi=0&s=laserjet%201100&os=64-bit. You should see a link "Free download required. Follow this link. It leads you to a driver?