VMware Player 5.0.1 - USB no driver found error.

Similar Questions

• USB flash drives not error 39 working -.

  Original title: USB flash drives doesn't work do not

  Hello
  My USB flash drives do not work in one of my USB slots. All other USB devices work correctly.
  Device Manager displays a yellow triangle with an exclamation mark next to the hard drive
  Have tried to update the drivers but points out the best drivers already installed.
  Connection drive after that a restart prompt message "driver installation", followed installation failed, error 39.
  I installed the latest drivers for the chipset of my Board.
  I have the Nations United-mounted and re-installed readers all affected.

  Grateful for the help, please.

  conx82

  Hello

  Have you tried the thumbdrive in another computer to be sure that it is still viable?

  ----------------------

  Try a restore of the system back to until the drive disappeared.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -----------------------------------------------------------

  If necessary:

  References to Vista also apply to Windows 7.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - anywhere in the area of white/white - point of VIEW, then-
  Show hidden devices

  Look everywhere EXCEPT USB controllers for your device and if find you them (maybe
  plus_d' one of each) under disk drives, you can have several - right CLICK and UNINSTALL
  for all instances. (There may be none.)

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and methods of Vista and Windows 7 are the same
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer.
  as well as all USB devices that you previously used. Run Options and tick the three 1st choice
  to see if one is there.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  ----------------------------------------------

  This can be useful to determine if the wrong driver is loading.

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Downgrade from Windows 7 RC to Windows XP - no hard drive found error

  I have Windows 7 RC running on my DELL 8400 desktop computer and want to perform a new installation on Windows XP. Installation stops after the 1st (install Windows XP) screen with error message "No Hard Drive Found" and start again. I used to run XP OK on the machine before participating in the beta program. Please help as I am not ready to move again to the full version of Windows 7. My hard drive is a Western Digital 160 GB and the DELL 8400 has an edge Intel SATA Controller. Thanks for your help.

  Mike

  Hi Mike.

  You may be able to put the drive in the BIOS for a SATA legacy which will act as an IDE, which won't be visible when installing XP.  Otherwise, you need to get a copy of the SATA drivers, and then press F2 as the XP installation starts that will allow you to use the drivers that XP installation can see the SATA drive.

• Toshiba 320 GB external USB HARD drive - 10 error Code

  Basically, I bought one of these today and put everything and he put in place and for some reason, my computer refuses to recognize or even start it. Initially, he recognized new hardware, but then nothing happened. I found it in device manager and it says that it will not start due to a "Code 10". Anyone know what it is?

  Then I turned off my computer after about an hour of nothing, then tried again, once more he recognized a second but a pop up came that said an error has occurred and may not work properly. Again, someone knows why this happened?

  Any help would be greatly appreciated. Thank you.

  Hello

  Code 10 means that the device could not start.
  Make sure you have the latest driver installed for your device. You may also be able to resolve this issue by removing the device in Device Manager, and through the Add New Hardware Wizard in Control Panel.

  It is also possible that your USB HDD needs an external power supply.
  If the USB device needs more than 500 ma, so usually an external power supply is required.

• EzCAP 116 USB 2.0 TV USB EMPAudio driver installation error.

  Just installed the drivers for a 2.0 ezcap USB video capture device and also the Arcsoft showbiz software. For some reason any my laptop does not recognize the driver audio 64-bit when I plug the unit gives a driver error audio ezcap 116 usb EMP. Fine video drivers

  When I try to capture the video, the software does not record sound and given no chance to change source resulting in a painful white noise that is emitted.
  Tried to re install the drivers and using another USB port with the same result.
  I have a laptop vaio Windows 7
  any ideas?

  Hi RickRoe,

  It seems that you are facing problems with video capture using EzCAP116 USB 2.0 Video Capture.

  I suggest you to consult and follow the steps from the link EzCAP116 USB 2.0 Video Capture Support and check if it helps.

  http://www.ezcap.TV/EzCAP116-drivers?ZENiD=5vbs59qnd75j8gph0ah03uc635

  For reference:

  http://www.ezcap.TV/Forum/

  I hope it helps. If you have any questions about Windows in the future, please let us know. We will be happy to help you.

• A machine virtual de VMware player can be saved on an external HDD for backup?

  Please allow me to set up the scene: I have a shadow PC from my main system on VMware Player

  I try an update on my 1st VM player. The update for my distro of choice borks the system, or at least a very important application. My corrections to the application can do worse things & this my system borks. I then delete the virtual machine.

  Now after this deletion, I do a reinstall Virtual complete. Then wait and see if a fix is coming in the next update.

  If I copy/home/username/vmware/opensuse to an external USB HARD drive.

  Is it possible after deleting a virtual machine in the drive to go to my USB and pick up my copy of opensuse in/home/username/vmware/and have it function like the old?

  Hey there,

  You can stop to the bottom of the virtual machine, copy the VM on your external HARD drive and be prepared to restore it if it breaks.

  If this post was useful/solved your problem, please mark the points of wire and price as seem you. Thank you!

• Can I make a partition D on VMWare Player?

  Hey all.

  I am new to the community and VMware.

  I use a non-commercial (free) version of VMware Player. I do a few laboratories of practice using Microsoft Servers. Some of the steps in my hands-on labs require a formatting drive D.

  My problem is, when I create the Machines, disk space is allocated on the C drive. There is no option to partition and create logical drives.

  The ""Options " are included in the"parameters "Manager allows adding additional HDs.» But not for the default partitioning, 40GB HD.

  I need to be able to run these commands... ["ntdsutil > activate ATN example > ifm > create sysvol full d:\ifm '] in order to complete the laboratory as well as additional measures that depend on the completion of this exercise. The command fails, because VMware Player always default to a huge drive C.

  Does anyone know of a work around this in VMware Player?

  Thank you

  Try to add a new disk in VMware Player editing options and then format the drive in Windows.

  Your virtual machine must be stopped before you add the disk.

• on usb driver install error

  in the windows 7 installation usb Acer driver aspire error e1-531 becomes as this computer does not meet the minimum requirements for installing this software

  Hello

  This error can occur if your computer does not have an operating system that is supported for the driver, or the driver version is not correct for your device. It could also be a problem if you download the wrong bit of the driver.

  For you help I would be grateful if you could answer the following questions:

  1. What version on key USB drivers are you trying to install?
  2. You did material recent or software on your computer changes before the show?
  3. Do you have any third-party security program installed on your computer?
  4. What is the full error message?

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-us/Windows/tips-fixing-common-driver-problems#tips-fixing-common-driver-problems=Windows-7

  Post back with the result so that we can help you further.

• keyboard does not (driver is loading don't not with the error code 38) after upgrading to VMWare Player 6.0.6 or 7.1.0

  Hi all

  Host: DELL M3800, Windows 8.1

  Since the update to VMware Player 6.0.6 (or 7.1.0) Windows is not loaded (error code 38) keyboard drivers.

  The device HID\VID_046D & PID_C313 & MI_00\7 & 362ebef & 0 & 0000 had a starting problem. (Pilot: keyboard.inf, problem: 0 x 26).

  I had no problem with previous versions (VMware Player 6 to 6.0.4).

  If I uninstall VMWare Player, Windows correctly loading the keyboard drivers.

  Now, if I reinstall the earlier version of VMware Player, Windows does not load properly (error code 38) keyboard drivers.

  Can you help me?

  Thank you

  Guillaume

  The problem is caused by the VMkbd.sys driver.

  You can find the "best" solution for Usb keyboard problem

• Detects the Wndows 7 + VMWare player + USB

  My host OS is Windows 7 Professional 64-bit, and my version of VMware player 5.0.2 build-1031769

  My problem USB devices cannot be connected to any guest OS running on VMware player.

  I tried CentOC 6buttons, Ubuntu 9.04 Ubuntu 12.04.

  the device icons are displayed top-right corner of the virtual machine, but when I right click-> Connect (disconnect form host)

  After a while "peripheral USB [Flash Drive] can not be connected device error" is appear.

  Device does not work correctly when it is connected to the host computer. It also detects and works fine when I connected to a

  virtual machine running on the Windows XP host.

  I spent a day hole in internet research. Please give let me know how to solve this problem.

  It seems that no one can give me a solution, anyway I solved the problem of upgrading my version of VMware player to 6.0.0 build-1295980

• Ultrabook HP 4 t-1100 - hard drives defective - No. DVD player - made HP sells recovery USB flash drives?

  Hello

  I am repairing a laptop HP Touchsmart Ultrabook 4 t-1100 for a friend. The pc wouldn't start. BSOD, would try to repair itself, then BSOD again. I ran the hard drive from the bios test. He said that the hard drive has failed. I bought a new drive hard Western Digital 7mm Blue, replaced the wrong drive, has passed the test to drive hard and then asked my friend if she had the Windows 8 recovery disc or a flash supplied with the computer player.

  Apparently, the recovery discs are not included with Ultrabooks, nor are a recovery flash drive. Being that this computer has been for a schoolgirl teenager, given to him by his mother of the computer-illiterate, nor had the foresight to do a restore of backup USB flash drive. All Ultrabooks do not have a reader of CD/DVD/BLU, so a USB recovery "disk" is necessary.

  I don't have another computer to Windows 8 lying autour to make a USB recovery. Some people sell images of USB recovery on eBay, but they don't seem very good reputation.

  And apparently they do not put the product key of Windows 8 on the bottom of portable computers more either! HP offers to sell a "recovery disc" through their section of the support of their website, but it is obviously not a DVD player to put it in.

  Here's my quandry: If I buy the "recovery disk" HP, they will send me a DVD or a USB FlashDrive with a system image on it? And if they send me DVD, I'll be able to put it in a computer Windows 7 and make a bootable system image that then I could put it on a USB key? Then, Windows will automatically find the product key?

  Hello:

  When I click on the link below, I see an option to order a recovery media USB for this model.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4132&LC=en&cc=us&DLC=en&sw_lang=&product=5328025

• You want to know how VMware player has demonstrated in supporting printer HP LJ P1100w USB devices for example.

  Original title: VMWARE Player, what went right?

  All of a sudden, VMWare Player [Win XP it] recognized and installed my printer HP LJ P1100w.  This, after being informed by them, by phone, that this freebie version does not support any usbs in addition to human and internal interface.  So, I decided to try to install my Deskjet 5400. I got a download HP upgrade package, uninstalled the existing software and Lo! VM has ask me to cut the host device and install it. Test page printed.

  What I want to know, since I can't get the response from VMWare, is how is it? There have not been updated for ages.

  Anyway, this avoids everything that copy/paste, drag and drop and no quality control before submitting the. PRN to Frogmore Rawprint.

  Hello

  VMware technical support technicians will be better placed to provide you with information:

  Assistance to Support VMware

  Hope the helps of information.

• How to get the external hard drive to connect to VMWare Player?

  Hi all

  I currently have VMWare Player 3.1.4 and that you have a VM installed on an external SSD that works very well.

  The guest operating system is XP and host operating system is OpenSuSE 11.4.

  The problem is that I have another external hard drive that I want to connect to the virtual machine to store files and other (WD Scorpio Black 320 GB).

  So what I tried was when I opend VMWare Player, I went to add a new SCSI device, found the hard drive, I wanted to use and created it. But when I go in-> "VM" > "Removable devices" > "generic SCSI (SCSI 0:1) ' > 'Connect'-> I get the below error message.

  Device virtual scsi0:1: could not open the device host "/ dev/sdc": not sufficient permissions to access the file. Please make sure that the virtual device is configured to use a Linux generic SCSI device (/ dev/sg *), and that the physical device works normally on the host computer.
  Cannot connect the device virtual scsi0:1.

  Does anyone know if I'm doing something wrong? What are the permissions are they talking about?

  Thanks in advance,

  Matt

  Are back at the office and tested on a variety of Linux Ubuntu and was able to add a second drive HARD/dev/sdb as a physical and even disc was also able to boot from it even if it needs to be dismantled first and I had to start VMware Player using sudo, because I was using a standard account both add the disk and run the virtual machine with the added disk.

• Usar USB Vmware player

  E possible em uma instalacao Vmware player sober windows7 64bits este player rodando windowx xp 32bits equipamentos online use has Máquina of da porta USB?

  Tenho wont o Vmware tools dentro da vm xp 32 bit este nao reconhece nenhum pendrive conectado ao computador, impressora nada scanner usb could then use me veio a doubt. "Will o' VM player mourned?

  Alguem Saberia me informar? is sim como devo proceed?

  em annex uma imagem com uma mensagem ao initialize o VMware ja procurei appears no referent of windows as portas usb is ok

  ATT

  DELROCK

  atribua os pontinhos clicando nas stars.

  ABCs

• Do I need work station to modify USB devices? You can also VMware Player...

  That's what I would do:

  Install VMware Player on Windows 7 evaluation version

  I have to configure a modem USB (ISDN-telephone line)

  Can I add this USB device to my virtual guest later in VMware Player?

  I feel like the installation of VMware Workstation for just add this USB device installation. I have no experience of using VMware Player. I've always had of VMware Workstation to support me in everything I've done, that's why I ask.

  I can only imagine that maybe VMware Player will limit to deal with the addition of devices/units, but what is the truth?

  Peripheral USB themselves act as plug-and-play.  As long as you have configured the virtual computer to have a USB controller and have installed the drivers (via VMware Tools) in the comments, you can attach any USB device to the guest with workstation, player, server, Fusion, etc..

  Workstation already includes the UI player interface so that you can test your VMS how they will be displayed to users who have installed Player.  There should be a shortcut installed for it.  You can run your VM via player INTERFACE and to answer to your question here, I think.