Volume on the laptop T530 indicator

Similar Questions

• laptop battery indicator always flashes

  Hello

  Why did the laptop battery indicator is always green / orange flashing?

  is there any solution outside the battery failure?

  Thank you

  Lanzartel

  Hello

  Please contact the Team Support from Dell. They should be able to help you.

  See the link.

  http://en.Community.Dell.com/?~CK_=_mn

• When you open the laptop, there is a beep noise

  Hello

  When I open my Lenovo X200t when it is in hibernation/standby, beep loud and as little as it may seem, it causes disturbances in time if not unnecessary.  I realize that it will not issue when the volume on the laptop is on mute or 0%, but y at - it another way, in which it will not beep?

  If you are not familiar with it, the sound signal also appears when the battery level is critical and four beeps.

  Please tell me that there is a way to turn it off!

  Thank you

  MoeKara

  You can disable it in the bios. F1 at the start screen, alarm, config, control, disable beep.  You can also disable the low battery alarm if you want from there.

• Volume of the speaker in X 40 question

  Dear Forum

  I have a question about my X 40. When I use it it is a built-in speaker and you can adjust the volume as much as possible to the maximum.

  However, I noticed that when the ultrabay docking station is used with the laptop, can reach a much higher sound volume when the laptop is used without the ultrbay docking station.

  Please anyone know why this is? Is it because there is another stakeholder in the docking station

  If someone can advise, I would be grateful.

  With best wishes

  Ian

  The answer is because the X 40 has himself a speaker built-in. Features detailed - ThinkPad X 40

  The X 4 What ban has two built-in stereo speakers.  Docking ban ThinkPad X 4 - Overview

  Hope this helps

• Volume on the ProBook s 4740 indicator

  Volume indicator does not display when you adjust the volume with the fn + f8/f9 key on ProBook 4740 s 64-bit Windows 7?

  Thank you.

  Hello

  Try reinstalling HP HotKey Support available on the following link.

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5229500&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_127051_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  When reinstalling, restart the laptop.

  Kind regards

  DP - K

• HP ENVY laptop - 15 - ae101no: control of the Volume on the keyboard keys do not work!

  Hello

  Volume control keys had suddenly stopped working, and I have no idea why. I have the model HP ENVY laptop - 15-ae101no (ENERGY STAR). Could you please help me fix it? Thank you!

  Hello

  Try the following.

  Download Realtek HD Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp74501-75000/sp74867.exe

  When finished, press and hold the Windows key and press R

  In the run window, type devmgmt.msc and press to enter.

  In Device Manager, expand sound, video and game controllers.  Right click on the Realtek device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

  When you are finished, download and reinstall the Chipset driver at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72105.exe

  When the reinstallation of Chipset is finished, stop the laptop.

  Disconnect the power adapter and then hold button power supply for 30 seconds, then release.

  Plug the power adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f9 to load the default values (sometimes it is f5, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  When windows has reloaded, open your download folder, right click on the installer of Realtek and select "Run as Administrator" to launch the installation.  Once this done, reboot the laptop and let windows load completely for a few minutes before checking.

  Kind regards

  DP - K

• The volume on my laptop icon keeps popping up on the screen every time

  The volume on my laptop icon keeps popping on the screen each time, whay could be the problem and how it can be corrected?

  Hello

  Brian says need us more information about your problem.

  Please describe the problem you are experiencing.

  Tips for solving common audio problems

  B Eddie

• the volume on my laptop lenovo does not work

  the volume on my laptop lenovo does not work, I ran the troubleshooting but he days my driver does not work properly, I have uninstalled/reinstalled but still have the same issue - no volume. everything I've tried has not worked. I can't put the volume up and down but always the same volume no matter what I try! Could someone please!

  Hello

  1. you receive an error message?

  2 did you change on your computer before this problem?

  3. what operating system is installed on your computer?

  What version of the operating system Windows am I running?

  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  Follow the suggestions and see if it helps.

  Method 1

  You can follow the steps and see if it helps.

  (a) right click on the Volume icon in the Notification area.

  b) click on tab reading.

  (c) right click on the box empty.

  d) select Show disabled devices.

  e) right click speakers and select allow.

  f) right click on speakers and go to the Properties.

  g) select use this device from the use of the device.

  h) click apply and OK.

  Method 2

  If it was working fine before, you can restore the computer settings to a date where he worked very well earlier.

  System restore

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

  See also:

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Sound cards: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/sound-cards-frequently-asked-questions

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

• How can I return the volume bar display after reimagee the laptop? HP Pavilion dv6 2120sl

  Hello

  I just got back my cell phone after being reimagee Windows.

  There are above the keyboard volume and tabs of wi - fi, wi - fi works very well, if I turn it off it changes the color red. However not in the same goes for the volume (it's always white) and also before the reimage whenever I put the volume there was little box on the screen showing how I changed the volume... Now, still works, but I want this little box back what seemed before. How can I do?

  I installed HP MediaSmart together - and restarted the laptop after her, but always without success.

  I have a 64-bit Windows 7 installation.

  Do you have any suggestions?

  Thank you.

  Hello mmirjam, welcome to the Forums of HP.

  It seems that your lack of 'volume bar' since having your laptop reimagee. I will try to help you with this.

  Start using this document from Microsoft: how the icons appear in the notification area of change.

  He should be able to guide to check settings, to see if this has been changed.

  If this does not work, then try to update the audio drivers: HP Pavilion dv6-2120sl Entertainment Notebook PC Drivers.

  I would like to know how it all happens.
  Thanks for posting on the HP Forums.

• Just after I turn on the laptop (before that turns on Vista) I get "cannot open volume for direct access.

  Just after I turn on the laptop (before Windows Vista turns on) the following message appears "cannot open volume for direct access.  What this mean and how can it be solved?

  Thank you

  Eddie

  Hi EddieLopezA,

  ·         Which version of Windows Vista is installed on your computer?

  ·         You have antivirus software on your computer?

  This problem may occur if another utility or service, for example a virus check program or a program disk monitoring, locked the partition before you try to run the Chkdsk.exe or Autochk.exe utility.

  I have some steps that may help you.

  Method 1: I suggest you to turn off all third-party applications and check if you have a similar question.

  To do this, follow these steps:

  1. open the start search box, type services.msc and click OK.

  2. in the Services (Local) list scroll the service concerned (for example auditor of virus or disk monitoring tool).

  3. right click on the service and select Properties.

  4. change the startup type to disabled for all applications 3rd - party that could be the cause of the blocking of Chkdsk problem.

  5. click OK/apply.

  6. restart the computer.

  Method 2: If this does not help, try to change the registry value and restart the computer.

  1. click on the start search box, type regedit.

  2. in the Publisher of the registry under the HKEY_LOCAL_MACHINE subtree, go to the following subkey:

  \SYSTEM\CurrentControlSet\Control\Session manager

  3 change the Boot entry run of:

  autocheck autochk * /r\DosDevice\C: (or other)

  TO:

  autocheck autochk *.

  Note: Change the settings of the REGISTRY can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the REGISTRY settings configuration can be solved. Changes to these settings are at your own risk.  If you want to edit the registry to fix this I urge you to back up your registry before proceeding.

  Links for:

  Unable to run CHKDSK

  http://support.Microsoft.com/kb/555484 (also applies to Vista)

  Hope the helps of information.

• To run all the applications of the laptop or install download applications works does not error message indicating that the application is not valid "win32.exe or win32.application.

  To run all the applications of the laptop or install download applications works does not error message indicating that the application is not valid "win32.exe or win32.application.

  Hello m.velentino,

  Not sure if you are still having the error message isn't valid win32.applicaiton.

  Get the error: not a valid 32-bit application can have several origins:
  I have listed some of them below.

  The file is corrupted, bad or missing.
  -If the hard disk is damaged or hurt it cause work programs to fail, either because not all data can be read from the hard drive the program is damaged on the drive. Run scandisk and defrag on the hard disk to check for potential errors.
  -If you run the program from a shortcut on the computer, verify that the program is still on the computer. In some cases if the program is no longer installed on the computer, you can get this error.

  File is not designed for your version of Windows:
  -If you try to run a program that is not designed for your version of Windows, you can get this error.
  -Although many old programs designed to work in older versions of Windows will work with new versions of Windows, unfortunately, not all programs will not work.
  -If the program is an MS-DOS program more former start program or Windows, you can get this error.
  -If the program is designed for a 64-bit version of Windows and you are running in a 32-bit version of Windows, it will not work and generate this error.

  File is a virus, worm or other malicious program file.
  - This error can be generated by a file that is a virus, worm, Trojan horse or other type of malware file. Often, this will result because the antivirus installed on the computer will not allow the file to install or run. Try to analyze the file to check, it is not a virus or infected.
  -If the file has been checked and is clean, it is always possible that the virus protection program or a another program installed on the computer is at the origin of questions during installation or execution of the program. Start the computer in Mode safe and try to run the program. start the computer in Mode safe will be that nothing is running in the background that could cause this problem.
  
  Hardware incompatibility.
  -If you get this error during the installation of a program, it is also possible that the CD-ROM drive or the drive that you are installing the program from is not compatible with Windows or has drivers that are not compatible with Windows.
  -Download the latest drivers for your CD player or other of the manufacturer of the computer or the manufacturer of the equipment. (Microsoft does not pilot for other materials)

  Let us know if these suggestions help you.

  Marilyn

• Volume of the Satellite A80-127, reading

  I recently bought an SA80 and sometimes use it to stream audio, but its volume seems to be quite low. I tried using all options available through volume control the volume.

  So, can someone please confirm if that is the case with all laptops or y at - it maybe a problem with mine.

  Best regards

  Hello

  Have you checked for a physical volume on your SA80 (knob or button) control?

  He can control the volume regardless of the volume of software controls.

  HTH >)

• Question about volume adjust the volume knob - Satellite Pro U300

  Hello

  I have a problem with the volume control. When I adjust the volume using the button on the left side of the laptop, I can only choose 3 levels of "loudness":

  No volume, very quiet volume and maximum volume (from rabies).

  Is this normal, is not anyone have problems with this?
  I hope that the problem is because of the digital volume adjustment screw. The adjuster does not record the exact position of the volume button. Every time when I get a phone call at work (I listen to internet radio), I turn off the radio by using the adjustment screw on the side of the laptop. When I end the phone call, I always need to open the laptop and the volume on the windows task bar, because when I use the device volume control on the left side of the laptop, it will just immediately at maximum volume.

  Welcome them

  Hello

  It s very strange that your volume control contains only 3 levels of volume
  I noticed that Toshiba has released a new driver (v. 6.0.1.5473) sound on the European driver page.

  How about if the update driver sound?
  Audio driver certainly controls the volume sound and in my opinion it s worth a try.

  Good luck

• volume on the keyboard slider does not work

  can someone help me please the slider for the volume on my laptop decided to stop working can anyone help

  Hello

  First of all, download and reinstall HP Quick Launch Buttons on the link below.

  http://ftp.HP.com/pub/SoftPaq/sp48001-48500/sp48159.exe

  After the installation is complete, restart the computer and verify if the volume slider works now.

  If it doesn't work, try the following.

  Download IDT Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp48501-49000/sp48830.exe

  One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

  When you're done, shut down the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery, connect the power adapter and start Notepad.

  Let windows load fully, then open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.

  When this has completed, restart the laptop.

  Kind regards

  DP - K

• Re: How to reduce the volume of the alarm?

  I have some programs that use the beeper system to report that something has happened.

  While in desktop computers the good old ringtone usually has an own speaker beside the case,
  for laptops, just like the toshiba, it is common that the sound of the alarm sound is mixed with the regular audio driver and so go out with the normal audio of the headphone jack.

  Now, this beep is really STRONG, and mixer windows vista seems to not have a slider for her...

  is it possible to change the volume of the ringtone in a different way?

  > have some programs that use the beeper system to report that something has happened.

  1. have you checked if there is an option to turn off the sound signal in the programs?
  2 you can turn off the beep at all, as shown below:

  http://img267.imageshack.us/img267/5026/sounduw.jpg