VPN client: static ip address assignment for xauth

Similar Questions

• How to use ACS 5.2 to create a static ip address user for remote access VPN

  Hi all

  I have the problem. Please help me.

  Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.

  I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:

  1Ajouter step to attribute a static IP address to the user attribute dictionary internal:

  Step 2select System Administration > Configuration > dictionaries > identity > internal users.

  Step 3click create.

  Static IP attribute by step 4Ajouter.

  5selectionnez users and identity of the stage stores > internal identity stores > users.

  6Click step create.

  Step 7Edit static IP attribute of the user.

  I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.

  so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.

  Wait for you answer, no question right or not, please answer, thank you.

  There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached

• Static IP address assignment to a device? (An XBox)

  I'm trying to set up my XBox One to broadcast remote but I am completely ignorant when it comes to networking and rely the economy on the default settings. There seem to be three main parts to this process described here:

  - Port forwarding (which was explained by DexterJB. (Thank you!)

  -Allocating an address static IP to the device (This step)

  - and implementation of dynamic DNS

  I was wondering if someone would be willing to walk me through step of assigning a static IP address to a device, which in this case is my XBox One.

  I really wanted to know that for a while for other devices, but do not know if it is a thing of router or a computer thing. I'd appreciate any help.

  Hi @varxtis,

  You are welcome!

  Instead of setting a static IP address for your XBOX, you can make a reservation address so that the XBOX will have a compatible IP for port forwarding you have done. You can refer to the link below for the steps on how to do it.

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24091

  Kind regards

  Dexter

  The community team

• static IP address assignment to TiVo on BEFSR41 router

  Hello

  I'm trying to put in place a couple of TiVo cable already on my home network so I can 'see' on my Mac using the TiVo Express of Toast Titanium function and copy the TiVo on my Mac programs.   TiVo technical support suggested that the problem is that my Mac IP address is 198.162.1.100 (assigned automatically) and for some reason some of my TiVo is on 198.162.0.2 et.0.3.  They suggested that I have manually assign a static IP address for the for put them in 'sync' with my Mac address - that is to say, something in the range 198.152.1.xxx of TiVo.

  I was able to assign a static IP address of 198.162.1.109 to the head of the TiVo (and my Mac is still not see it), but I received an error message when I tried to assign 198.162.1.110 to the other TiVo.   Technical support suggested I check with you on assignment of the IP address via the router.  Can you tell me if this is possible and if so, how?

  Thank you!

  If the TiVo is Gets an IP 192.168.0.2 or similar when using dynamic/DHCP/Auto IP addresses means the TiVo is connected to a different router or get an IP address from another DHCP server.

  1. Please check your wiring. Your modem should connect to the internet, the port of the BEF everything is connected to the BEF. If the modem has additional LAN ports, a modem/router combo device. Do not use additional ports on the modem/router combo.

  2. If wiring is OK, as previously indicated another reason for a 192.168.0.2 automatic address IP sharing a computer inside your network that has been configured for an internet connection. With internet connection sharing you can share an internet connection through this computer. To do this, the computer will assign 192.168.0. * IP addresses on its side LAN. Please check your computers if there is one that has internet connection sharing enabled.

• Only 1 of the 2 computers in my LAN recognizes my static IP address assigned by my ISP - HELP!

  I have an IP address from my ISP, but only one of the two computers in my LAN presents this static IP address in the "ipconfig" and it connects to the internet, the other computer Watch has "169.254.XXX.XXX' IP address and does not connect to the internet.  How can I fix it? I don't know much about the TCP/IP settings.  OS is XP Pro SP3.  I have a DSL router from single port connected to a simple switch 5 ports, then two CAT5 cables will switch on both computers.

  Thanks for your help!

  derisk

  Hello

  Two computers cannot connect to the same connection using the same IP address. Each computer on the network must have its own unique IP address.

  You need to get a cable/DSL router. Configure the WAN port (Internet) side with your static IP address and connect all the computers the and other equipment network on the side of the router LAN.

  Generally, it looks like this, http://www.ezlan.net/network/router.jpg

  P.S. You don't need to use the wireless if you do not, it is very difficult to find a new wireless router.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• VPN client and contradictory static NAT entries

  Hello, we have a VPN IPSEC implemented on a router for remote access. It works very well, for the most part. We have also a few PAT static entries to allow access to a web server, etc. from the outside. We deny NATting from the range of IP addresses for the range of VPN client and it works except for entries that also have PAT configurations.

  So, for example, we have web server 10.0.0.1 and a PAT redirection port 10.0.0.1: 80 to the IP WAN port 80. If a VPN client tries to connect to 10.0.0.1: 80, the syn - ack packet back to the customer WAN IP VPN on the router! If the VPN client connects to the RDP server 10.0.0.2:3389, it works very well that this server is not a static entry PAT.

  Is there a way to get around this?

  Thank you!

  There is a way to get around, use the same settings you have for your dynamic nat in your nat staitc entries, something like this:

  Currently, it should show as:

  IP nat inside source static XXXXX XXXX 80 80

  you need to take it

  IP nat inside source static 80 XXXX XXXX 80 map route AAAA

  When your itinerary map YYY refers to something with an acl that you refuse traffic from inside your router for the pool of vpn

  IP Access-list ext nonat

  deny ip 10.0.0.0 0.0.0.255

  Licensing ip 10.0.0.0 0.0.0.255 any

  route allowed AAAA 10 map

  match ip address sheep

  You even need all the static PAT

  HTH

  Ivan

• Assign ACLs to VPN clients

  We have a client that VPN in a Pix 515. I inserted the configuration of intra-interface same-security-traffic allowed on the pix so that members of staff who use the VPN would be able to access a specific resource from the public side. What I would do is to continue to use the same-security-traffic intra-interface command permit, but restrict access to other resources to the VPN client. Can I assign an access list to the VPN client allowing 10.10.10.10 everything and refuse all other connections? Where can I insert this in the VPN structure?

  Thank you

  Yes.

  Kind regards

  Arul

  * Please note all useful messages *.

• The VPN client VPN connection behind other PIX PIX

  I have the following problem:

  I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

  So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

  I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

  Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

  If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

  305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

  194.x.x.x is our customer s address IP PIX

  I understand that somewhere access list is missing, but I can not understand.

  Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

  Can you please help me?

  Thank you in advan

  The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

  I've cut and pasted here for you to read, I think that the problem mentioned below:

  Question:

  Hi Glenn,.

  Following is possible?

  I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

  The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

  My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

  Thank you very much for any help provided in advance.

  Response from Glenn:

  First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

  fixup protocol esp-ike

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

  If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

  ISAKMP nat-traversal

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

  NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

  ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

  A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

  NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

  Hope that helps.

• Static IP address on the server 2008R2 disconnecting Internet

  Please help with a static IP configuration on VMware.

  I would like to configure Active Directory on VMware with FULL INTERNET AND IP ADDRESS, please help.

  Scenarios

  I use VMware on Windows 8.1 10 and that's what strikes me:

  1. After installing server 2008R2 on VMware and the activation of the "Connection NAT" network card, I had full access to the internet.
  2. 1920168.5.2 to server static IP address assignment disconnect internet.
  3. Add more network on the server to reconnect to the internet but removes the static IP address.
  4. Even the bridge two network cards, I still get internet access.
  5. Active directory cannot be installed on a dynamic IP address
  6. I connect using wireless (my cell phone as a modem).

  Your help will be greatly appreciated

  After following your instructions, I discovered that VM DNS is 192.168.111.2. Both the DNS and gateway uses the same IP address, DNS is indeed the gateway to NAT. la... 111... changes when you reset the VM machine. Also, I discovered that the DHCP of the VM is 192.168.111.128 as you put it. Now place the Client Server on the same network of VM IP, thus, take the given dynamic IP 192.168.111.128/129/130/131 etc, make it static. Assigning 192.168.111.2 as gateway and DNS, provides access to the internet. However, after configuring Active directory member servers will not find the domain controller uses the DNS of VM.  Instead, insert the IP of the VM DNS as secondary preferred over the IP of the DNS server (for example, DC1, DC2 mem1 etc.) in the preferred DNS. Then... VOALA... Is set with full internet access.

  It was a challenge to the calm, but I give you the thumbs up for your lead. You are the best.

• Unable to connect to other remote access (ASA) VPN clients

  Hello

  I have a cisco ASA 5510 appliance configured with remote VPN access

  I can connect all hosts on the INSIDE and DMZ network, but not able to access other clients connected to the same VPN.

  For example, if I have 2 clients connected to the VPN, customer and CustomerB, with a pool of vpn IP addresses such as 10.40.170.160 and 10.40.170.161 respectively, these two clients are not able to communicate with each other.

  Any help is welcome.

  Thanks in advance.

  Hello

  I'm a little rusty on the old format NAT, but would be what I would personally try to configure NAT0 on the 'outer' interface.

  It seems to me that you currently have dynamic PAT configured for the VPN users you have this

  NAT (outside) 1 10.40.170.0 255.255.255.0

  If your traffic is probably corresponding to it.

  The only thing I can think of at the moment would be to configure

  Note of VPN-CLIENT-NAT0-access-list NAT0 for traffic between VPN Clients

  list of access VPN-CLIENT-NAT0 permit ip 10.40.170.0 255.255.255.0 10.40.170.0 255.255.255.0

  NAT (outside) 0-list of access VPN-CLIENT-NAT0

  I don't know if it works. I did not really have to configure it on any ASAs running older software. There was some similar questions here on the forums for the new format.

  -Jouni

• ASA 5520: Remote VPN Clients cannot ping LAN, Internet

  I've set up a few of them in my time, but I am confused with this one.  Can I establish connect via VPN tunnel but I can't ping or go on the internet.  I searched the forum for similar and found a little issues, but none of the fixes seem to match.  I noticed a strange thing is when I run ipconfig/all of the vpn client, the IP address that has been leased over the Pool of the VPN is also the default gateway!

  I have attached the config.  Help, please.

  Thank you!

  Exemption of NAT ACL has not yet been applied.

  NAT (inside) 0-list of access Inside_nat0_outbound

  In addition, you have not split tunnel, not sure you were using internet ASA for the vpn client internet browsing.

  You can also enable icmp inspection if you test in scathing:

  Policy-map global_policy
  class inspection_default

  inspect the icmp

  Hope that helps.

• The VPN client user authentication

  When users connect to our network remotely via VPN user name field is already filled with the last person who logged. I know that they just delete the username and enter their own, but is there a way the client can be configured to where the username field will be always empty for all those who want access to the network via VPN? We have an ASA 5510 with version 7.0 (8) and a windows 2003 with IAS server for windows authentication. Thank you!

  Hello

  In FCP, you can configure a single line is not editable by the user (or the vpn client).

  Simply insert an attack! Like this

  ! Username =

  ! SaveUserPassword = 0

  ! UserPassword =

  ! enc_UserPassword =

  Subsequently the vpn client will not save registrations for these settings more.

• With PAT on Cisco PIX VPN client

  Dear all,

  I have a PIX 515 to the main site with the IPSec security is enabled. Homepage user using 3.x VPN client connects to the PIX for VPN access. When user Home use real IP, I can ping to the local network of the main site. However, when the Home user using a router with PAT, the VPN can be established.

  Is there a setting I should put on PIX, VPN client or router?

  Thank you.

  Doug

  And if you still have problems, upgrade your pix, 6.3 and usage:

  ISAKMP nat-traversal

  But the first thing would be to check the IPSEC passthrough as Ade suggested. If the device is a linksys check the version of the firmware as well.

  Kind regards

• Automatic reconnection VPN Client

  We have a PIX 515E and we have just implemented a few remote users. Everything has been working well, except that users have unreliable connections that often fall. When their ISP connection drops, they connect in the VPN client again. Is it possible to configure the clients to automatically connect to the VPN when a connection is present, similar in the manner of that site to site VPN works transparently for the user?

  We currently use the client 4.6 and are open to try other methods of remote users connect to the PIX (PPTP, etc.)

  The VPn client has an auto-initie function, in that when he sees the traffic to a specific destination, it will bring up the tunnel. If you allow users to save their passwords, then the whole process can be transparent.

  See http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/4_6/admin/vcach4.htm for more details.

• ASA static IP Addressing for IPSec VPN Client

  Hello guys.

  I use a Cisco ASA 5540 with version 8.4.
  I need to assign a static IP address to a VPN client. I saw in the documentation Cisco that this can be done to validate the user against the local ASA and in the user account database, you assign a dedicated IP address, or using the vpn-framed-ip-address CLI command.
  The problem is that the customer never gets this address and it always gets one of the pool in the political group. If I delete this pool, the client can't get any address.
  No idea on how to fix this or how can I give this static IP address to a specific VPN client?
  Thank you.

  Your welcome please check the response as correct and mark.

  See you soon