VPN site-to-site between two PIX 501 with Client VPN access

Similar Questions

• VPN connection between two pix firewall problems

  Hi, trying to create a VPN between the firewall two pix a 501 and a 506e.

  currently on the 506th pdm shows 1 IKE tunnel in the stats, but it displays then return to zero. The two hosts of pix can access the web and ping each other gateways.

  I posted the 506th config but the 501 config is the same.

  outside IP for pix 506th = a.a.a.a

  outside IP for pix 501 = b.b.b.b

  Internet service provider ip of the gateway to 506th = x.x.x.x

  Thank you

  Alex

  Hi Alex

  See the configuration on the other side (PIX501) it will be difficult to solve, you'll need to be sure when it is a phase failure 1 or phase 2.

  Please note between the two PIX IPSec negotiation fails if both of the phases SAs IKE do not match on the peers.

  Cordially MJ

• PIX 501 with Actiontec Q1000 in Bridge mode

  I have an Actiontec Q1000 Qwest racetrack with 8 static IP addresses.  I want to put the Actiontec in bridge mode and connect the PIX.  I have configured the PIX as follows, but there are some things that are unclear to me:

  IP address outside pppoe setroute

  VPDN group chi request dialout pppoe

  VPDN group chi localname xxxxx

  VPDN group chi ppp authentication pap

  VPDN username password xxxxx xxxxx

  Qwest gave me a block of 8 IP, and they either of them specified as a gateway address.

  This IP will get the external interface?

  Can I use setroute with Qwest, or I need to specify a default route instead?

  Can I assign the gateway address to the external interface of the PIX?

  My ultimate goal is to be able to configure the PIX to allow client software Cisco VPN incoming connections.

  Thank you very much for all your comments.

  P.S. I can't just try, because I am in California and I need to set it up and send it to Utah, where I there will have access via SSH.

  The ip address will be given by provide it during the negotiation of PPPoE.

  You should be able to use the road together, I would expect Qwest provide the default route in PPPoE.

  I should get it by the ISP automatically.

  Please evaluate the useful messages.

  PK

• Switch between two intelligent forms with a single button?

  Hello!  I work at 8 Captivate and try to use a single button to switch between two smartshapes.  I can't for the life of me figure out how to do it.  I know its possible to make it 'show' and 'hide', but is it possible to simply create a user click on a button and whenever we click on it, it comes and goes between two different smartshapes?

  Im trying to show the user the functionality on a piece of equipment when they press a button.  When they push the button, it comes and goes between two different read out on the screen.

  Thanks in advance!

  Have you looked at the blog post that I posted a link: I offer 4 scenarios.

  It can also easily be done, if you have a separate (shape) button to switch between two different objects:

  1. Create a user with a default value of 0 v_visib variable
  2. Create two objects and one of them is visible, the other invisible output ("eye" in the Properties Panel icon); I've tagged the ShapeOne and ShapeTwo, where ShapeOne is visible at the beginning
  3. Create this advanced conditional action (you can also turn it into a shared action):

  IF v_visib equals 0
  Hide ShapeOne
  See the ShapeTwo
  Toggle v_visib
  ON THE OTHER

  Hide ShapeTwo

  See the ShapeOne

  Toggle v_visib

  4 assign this action to the success of the button event

• site-to-site between two ASA firewall

  Hello

  I have two ASA and I have set up the two ASA til S2S. ASA1 is in HQ and ASA2 is in Office of Brunch. HQ ASA has multi S2S connection and Brunch ASA has only S2S to Headquarters. The Senario is I want to send all traffic (both Internet and LAN in the ASA HQ) ASA2 throug the tunnel. The problem is that when the tunnel is up and there is ASA2 connevtivity (brunch office) for the network local behinde ASA1 (HQ), but the client behinde ASA2 has no conectivity when they try to go to the Internet. Tanks a lot in advance for any help!

  ASA HQ extern ip 192.x.y.z/24, LAN 10.70.0.0/16

  Brunch of the ASA Office a extern ip 168.x.y.z/24, LAN 10.79.1.0/24

  This should help you:

  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0

  access extensive list ip 10.79.1.0 inside_nat0_outbound allow 255.255.255.0 255.255.255.0 x.x.x.x
  access extensive list ip 10.79.1.0 outside_1_cryptomap allow 255.255.255.0 255.255.255.0 x.x.x.x

  x.x.x.x = subnet HQ, in the ASA HQ you need of the opposite ACL:

  permit inside_nat0_outbound to access extended list ip x.x.x.x 255.255.255.0 10.79.1.0 255.255.255.0
  permit outside_1_cryptomap to access extended list ip x.x.x.x 255.255.255.0 10.79.1.0 255.255.255.0

  This way to the internet traffic will be coordinated because it turns off and traffic to the VPN will be
  not be translated as she goes down the tunnel

• PIX 501 with public several IP addresses

  Hi all

  I have the following configuration:

  audience of 6 IP addresses, for example: 123.123.123.1 - 6 255.255.255.248

  My provider, I have a Zyxel modem which has the 123.123.123.1 IP address, which is also the default gateway for my PIX.

  The PIX is connected to a modem Zyxel.

  The external interface of the PIX, 123.123.123.2 and the inside interface 192.168.1.1 255.255.255.0

  At my home I have several client computers and network servers 3.

  Client computers must be able to connect to the internet.

  Server should have the public IP 123.123.123.3 and 192.168.52.3 inside

  Server B must have public IP 123.123.123.4 and 192.168.52.4 inside

  Server C must have public IP 123.123.123.5 and 192.168.52.5 inside

  Server 3 are Web servers and should be accessible from the outside on ports 80 and 443.

  My current setup is:

  See the pixfirewall (config) # executes
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password
  encrypted passwd
  pixfirewall hostname
  domain ciscopix.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  object-group service tcp web
  port-object eq www
  EQ object of the https port
  OUTSIDE of the ip access list allow any host 123.123.123.3
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP outdoor 123.123.123.2 255.255.255.248
  IP address inside 192.168.1.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  location of PDM 192.168.1.0 255.255.255.0 inside
  history of PDM activate
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 192.168.1.0 255.255.255.0 0 0
  static (inside, outside) tcp 123.123.123.3 www 192.168.1.3 www netmask 255.255.255.255 0 0
  Access-group OUTSIDE in interface outside
  Route outside 0.0.0.0 0.0.0.0 123.123.123.1 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.2.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet 192.168.2.0 255.255.255.0 inside
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  Terminal width 80
  : end
  pixfirewall (config) #.

  This acutally configuration only allows connections from the inside to the outside but not from the outside to connect to the server.

  I'm sure miss me something stupid, maybe someone could give me a hint?

  Mike

  Setup looks quite right, assuming that you only test connectivity to Server A (123.123.123.3) as it is the only one configured.

  I suggest that you make 'clear xlate' and 'clear the arp' and test again. I would check to see if your modem has the ARP entry for 123.123.123.3 and it should point to the ethernet0 PIX MAC address.

• Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.

  I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.

  .

  The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).

  .

  A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?

  .

  I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?

  .

  Thank you.

  UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.

  The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.

• VPN site to site Pix 525 ver7.2 (2) and Pix 501 ver 6.3

  Hello!!

  I have problems to establish a vpn between two pix.

  The first pix 525 a version 7.2 (2) an another Pix version 6.3 has this it is not run by myself.

  The fixed phase 1 but send the associated messages

  can help me

  Thank you

  I'm glad you got it working now :)

  Please evaluate the useful messages.

  Concerning

  Farrukh

• VPN site to Site - ASA to PIX - same subnet on the inside

  Chaps,

  I have a unusual scenario, whereby case I need a tunnel vpn site-to-site between a pix of cisco version 7 and version 8 cisco asa, which have the same subnet ip to each endpoint.  Is it possible to create such a tunnel from site to site or do I change one of the remote endpoints?

  Thank you

  Nick

  Hi Nicolas,.

  To allow the traffic through the tunnel when having the same at both ends addressing scheme, you should NAT VPN traffic.

  That is to say.

  Site a 10.1.1.0/24 LAN

  Site B LAN 10.1.1.0/24

  The site config:

  NAT permit list to access ip 10.1.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  (in, out) static 192.168.1.0 access-list NAT

  license of crypto list to access ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  Site B config:

  NAT permit list to access ip 10.1.1.0 255.255.255.0 192.168.1.0 255.255.255.0

  (in, out) static 192.168.2.0 access-list NAT

  license of crypto list to access ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0

  The idea is that Site A will to 192.168.1.0 translatefd when you go to Site B, and Site B will result to 192.168.2.0 when you go to the Site A.

  Hope that makes sense.

  Federico.

• VPN PPTP and PPPOE CLIENT ON PIX 501

  Hello

  Can I create a PPTP VPN and a client connection on a PIX 501 with a client to my ISP PPPOE connection. The PPPOE ip is dynamic and the VPN will be a static IP address. They gave me a username and password for VPN and PPPOE. Him also gave me an ip address for the VPN server.

  Should that happen, it's that the PPPOE should connect to the VPN to work.

  I can only get the PPPOE, but I don't know how to do this with a PPTP VPN set.

  Here is my config:
  
  PIX Version 6.3(3)
  
      interface ethernet0 auto
  
      interface ethernet1 100full
  
      nameif ethernet0 outside security0
  
      nameif ethernet1 inside security100
  
      enable password xxxxxxxx encrypted
  
      passwd xxxxxxx encrypted
  
      hostname neveroff
  
      domain-name neveroff.com
  
      fixup protocol dns maximum-length 512
  
      fixup protocol ftp 21
  
      fixup protocol h323 h225 1720
  
      fixup protocol h323 ras 1718-1719
  
      fixup protocol http 80
  
      fixup protocol rsh 514
  
      fixup protocol rtsp 554
  
      fixup protocol sip 5060
  
      fixup protocol sip udp 5060
  
      fixup protocol skinny 2000
  
      fixup protocol smtp 25
  
      fixup protocol sqlnet 1521
  
      fixup protocol tftp 69
  
      names
  
      access-list incoming permit icmp any any echo-reply
  
      access-list incoming permit icmp any any source-quench
  
      access-list incoming permit icmp any any unreachable
  
      access-list incoming permit icmp any any time-exceeded
  
      pager lines 24
  
      icmp permit any echo outside
  
      icmp permit any unreachable outside
  
      icmp permit any time-exceeded outside
  
      icmp permit any source-quench outside
  
      icmp permit any echo-reply outside
  
      icmp permit any information-reply outside
  
      icmp permit any mask-reply outside
  
      icmp permit any timestamp-reply outside
  
      mtu outside 1500
  
      mtu inside 1500
  
      ip address outside pppoe setroute
  
      ip address inside 192.168.1.1 255.255.255.0
  
      ip audit info action alarm
  
      ip audit attack action alarm
  
      pdm logging informational 100
  
      pdm history enable
  
      arp timeout 14400
  
      global (outside) 1 interface
  
      nat (inside) 1 192.168.1.0 255.255.255.0 0 0
  
      static (inside,outside) tcp interface smtp 192.168.1.201 smtp netmask 255.255.255.255 0 0
  
      access-group incoming in interface outside
  
      timeout xlate 0:05:00
  
      timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
  
      timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
  
      timeout uauth 0:05:00 absolute
  
      aaa-server TACACS+ protocol tacacs+
  
      aaa-server RADIUS protocol radius
  
      aaa-server LOCAL protocol local
  
      http server enable
  
      no snmp-server location
  
      no snmp-server contact
  
      snmp-server community public
  
      no snmp-server enable traps
  
      floodguard enable
  
      telnet timeout 5
  
      ssh 0.0.0.0 0.0.0.0 outside
  
      ssh 0.0.0.0 0.0.0.0 inside
  
      ssh timeout 5
  
      console timeout 0
  
      vpdn group pppoex request dialout pppoe
  
      vpdn group pppoex localname xxxxxxxxx
  
      vpdn group pppoex ppp authentication chap
  
      vpdn username xxxxxxxx password xxxxxxxx
  
      dhcpd address 192.168.1.10-192.168.1.41 inside
  
      dhcpd dns 192.168.1.1 168.210.2.2
  
      dhcpd lease 3600
  
      dhcpd ping_timeout 750
  
      dhcpd auto_config outside
  
      dhcpd enable inside
  
      username neveroff password TEnlGTQMwqamBzMn encrypted privilege 2
  
      terminal width 80
  
      Cryptochecksum:c5bfafa70f21ed55cc1b3df377e110bf
  
      : end
  
      

  Thank you

  Etienne

  Happy to help and please kindly mark the message as answered if you have not more than other questions. Thank you.

• PIX 501 Logging

  I would like to open a session of hacking and intrusion of the attacks through a PIX 501 with a connection to broadband in a Home Office Setup. I have the camera upwards and the race and I am currently Setup with the Kiwi Syslog Dameon. What would be my best approach Logging all relevant information with the load to the bottom of the unit? Any suggestions / tips would be appreciated.

  Thank you

  It is a common logging configuration that I use:

  opening of session

  timestamp of the record

  logging trap information

  host of logging inside x.x.x.x

  No registration message 106015

  No message logging 106007

  No message logging 105003

  No registration message 105004

  No message recording 309002

  No message logging 305012

  No registration message 305011

  No message logging 303002

  No message logging 111008

  No message logging 302015

  No message recording 302014

  No message logging 302013

  No registration message 304001

  No message logging 111005

  No message logging 609002

  No message recording 609001

  No message logging 302016

  I usually do not enable the logging buffer (never use connection console it will affect performance) because it's not the messages timestamp (it only timestamps in the syslog). But the PIX loaded down with the load, you and Kiwi you before the PIX don't.

  Also turn on the IDs on the PIX.

  It will be useful.

  Steve

• Configure the PIX 501 for IDS

  I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?

  IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.

  If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.

  You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.

• Bluetooth connection between two 7290

  Hello

  I want to create a connection between two BlackBerry 7290 with OS 4.1 I found something with BluetoothSerialPort, but if I pair the und devices 2 start the application I get no BluetoothSerialPortInfos with the static method of the BluetoothSerialPort class.

  I tried to create a BluetoothSerialPort without an Info but that does not work. I get an IOException to Scripture.

  public boolean keyChar (key char, int status, int time)

  {

  If (key is Characters.ENTER)

  {

  Try

  {

  _port = new BluetoothSerialPort ("Hi there", BluetoothSerialPort.BAUD_115200, BluetoothSerialPort.DATA_FORMAT_PARITY_NONE |) BluetoothSerialPort.DATA_FORMAT_STOP_BITS_1 | BluetoothSerialPort.DATA_FORMAT_DATA_BITS_8, BluetoothSerialPort.FLOW_CONTROL_NONE, 1024, 1024, this);

  H = 'hi. '

  _port. Write (h.GetBytes ());

  }

  catch (Exception e) {Dialog.alert (try ()) ;}}

  }

  }

  At this point, I get the Exception when writing. Can someone help me please? Martin

  When you pair the Bluetooth devices, they exchange a list of services they support.  This means that you will need to have a server side application up and running which listens to the incoming Bluetooth connections before they are matched.  Otherwise, the other Bluetooth device will not know about your application and will not be able to connect to it.

• PIX 501 PPPoE w / static NAT loss of connectivity

  I have a {should} installation very simple. PIX 501 with PPPoE on the external interface, 3 inside customers using PAT and 1 inside the client I am trying to use an address mapping static on permit communications with this host from the outside using a particular service. I did a lot of these before where there was an ADSL router in front of the PIX, but this is the first where I've used the PIX as the PPPoE client. When I use the static NAT for the single host it loses all connectivity beyond the PIX outside interface. When I get rid of the static mapping, through PAT very well. I spent many hours troubleshooting and control a lot of obvious things, but I am at a loss right now... unless it could be a problem with the IP address that has been assigned by the ISP for use with static NAT. Any thoughts on this would be greatly appreciated.

  Thank you

  Sorry, in your case that static would look like this because of the dynamic IP.

  static (inside, outside) 23 interface 10.1.1.1 23 netmask 255.255.255.255

  Daniel

• Don't host any remote VPN access

  Hello guys,.

  I have an ASA 5505 with two tunnels, a Site to Site (between two ASA 5505), and also, I added a remote access VPN using the factor of Cisco's VPN. The thing I discovered is that the Site to Site connection, I can reach the hosts of the LAN, but the use of the VPN Client I only can reach the inside Interface of the ASA, but not for the hosts.

  Something is perhaps missing from my ACL but I was not able to determine what it is. You give me a hand on this?

  Attached my config file, and the LAN behind the ASA consist in a couple of VLAN segment 192.168.0.0 24 receives the Client VPN IP to the 10.10.10.X segment

  Thanks in advance,

  Hi David,

  You are missing a statement of NAT exemption.

  Need to add this:

  access-list sheep extended 10.10.10.0 any allowed ip 255.255.255.0