PIX 501 Logging
I would like to open a session of hacking and intrusion of the attacks through a PIX 501 with a connection to broadband in a Home Office Setup. I have the camera upwards and the race and I am currently Setup with the Kiwi Syslog Dameon. What would be my best approach Logging all relevant information with the load to the bottom of the unit? Any suggestions / tips would be appreciated.
Thank you
It is a common logging configuration that I use:
opening of session
timestamp of the record
logging trap information
host of logging inside x.x.x.x
No registration message 106015
No message logging 106007
No message logging 105003
No registration message 105004
No message recording 309002
No message logging 305012
No registration message 305011
No message logging 303002
No message logging 111008
No message logging 302015
No message recording 302014
No message logging 302013
No registration message 304001
No message logging 111005
No message logging 609002
No message recording 609001
No message logging 302016
I usually do not enable the logging buffer (never use connection console it will affect performance) because it's not the messages timestamp (it only timestamps in the syslog). But the PIX loaded down with the load, you and Kiwi you before the PIX don't.
Also turn on the IDs on the PIX.
It will be useful.
Steve
Tags: Cisco Security
Similar Questions
-
I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?
IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.
If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.
You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.
-
How to configure the PPPoE on PIX 501?
Mailto: [email protected] / * /
According to the below URL Cisco TAC:
but I always failed. And my PIX 501 Configuration noted below:
pixfirewall # write terminal
Building configuration...
: Saved
:
6.3 (1) version PIX
interface ethernet0 10baset
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable password xxxx
passwd xxxx
pixfirewall hostname
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
names of
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside pppoe setroute
IP address inside 192.168.1.254 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1
Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN group pppoex request dialout pppoe
Cisco localname VPDN group pppoex
VPDN group ppp authentication pap pppoex
VPDN username xxxx password *.
Terminal width 80
Cryptochecksum:xxxx
: end
[OK]
See the pixfirewall version #.
Cisco PIX Firewall Version 6.3 (1)
Cisco PIX Device Manager Version 1.1 (2)
Updated Thursday 19 March 03 11:49 by Manu
pixfirewall until 58 mins 6 dry
Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU
Flash E28F640J3 @ 0 x 3000000, 8 MB
BIOS Flash E28F640J3 @ 0xfffd8000, 128KB
0: ethernet0: the address is 000b.fd58.886b, irq 9
1: ethernet1: the address is 000b.fd58.886c, irq 10
Features licensed:
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Maximum Interfaces: 2
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: 50
Throughput: unlimited
you have all the debugging logs?
-
Unable to connect to PDM on PIX 501
just cannot understand this. I have a PIX 501 I used to connect very well. Now I can't get the PDM to come up inside, outside, nothing. I use the same (old) of JAVA 1.4 version I always used. I can Telnet etc... Very well. The HTTP server is enabled and have granted access from my IP address. Any help would be greatly appreciated. See my config below.
See the pixfirewall # running
: Saved
:
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry2YjIyt7RRXU24 encrypted password
passwd encrypted XXXXXXXX
pixfirewall hostname
domain ciscopix.com
clock timezone IS - 5
clock to summer time EDT recurring
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 X 0
fixup protocol h323 ras X 18 - X 19
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
name admin_subnet X.X.X.X
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow admin_
subnet 255.255.0.0
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow X.X
. X.X 255.255.255.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list permit admin_subn
and 255.255.0.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list allow X.X.X
. X 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP outside X.X.X.X 255.255.255.128
inside X.X.X.X 255.255.255.0 IP address
alarm action IP verification of information
alarm action attack IP audit
PDM location admin_subnet 255.255.0.0 outside
location of PDM X.X.X.X 255.255.255.0 inside
PDM location x.x.x.x 255.255.255.255 outside
location of PDM X.X.X.X 255.255.255.0 outside
location of PDM X.X.X.X 255.255.255.255 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http X.X.X.X 255.255.255.0 inside
http admin_subnet 255.255.0.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map pfs set 20 group2
card crypto outside_map 20 game peers X.X.X.X
outside_map crypto 20 card value transform-set ESP-AES-256-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address X.X.X.X 255.255.255.255 netmask No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 aes-256 encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 8 X 00
Telnet X.X.X.X 255.255.255.0 outside
Telnet X.X.X.X 255.255.255.0 inside
Telnet admin_subnet 255.255.0.0 inside
Telnet timeout 30
ssh X.X.X.X 255.255.255.255 outside
X.X.X.X 255.255.255.0 inside SSH
SSH timeout 30
management-access inside
Console timeout 30
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
username password XXXXXX XXXXXXXXXXX encrypted privilege 15
Terminal width 80
Cryptochecksum:
: endHello Mark,
lol Nice to know that everything works fine now
Don't forget to mark it as answered and to classify the useful messages (if you don't know how to evaluate a message just to get to the bottom of each answer and mark 1 being a wrong answer, being a great answer 5 stars)
Kind regards
Julio
PD: Some kudos for you (because of the answer)
-
I am very new to cisco equipment and I was wondering if someone could help me with this (probably very simple question).
When connecting to my pix via the browser (https://192.168.1.1/startup.html), the browser never took the start screen with the message that says "loading, please wait." This leads me to believe that the firewall is rejecting connections from my machine (which uses dhcp to get an ip address of the pix).
To work around this problem, I tried to connect to the CLI using hyperterminal. I can connect and run a few basic commands as 'show version', but cannot log on as a user with permissions.
If the web interface has a default connection of void & empty, surely the cli should be the same?
Is anyone able to tell me what is the default login, so that I can start confguring the pix via the cli?
Thanks in advance.
Justin Spencer.
Please see below for info pix:
Cisco PIX Firewall Version 6.3 (3)
Cisco PIX Device Manager Version 3.0 (1)
Updated Thursday, August 13 03 13:55 by Manu
pixfirewall until 12 minutes 18 seconds
Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU
Flash E28F640J3 @ 0 x 3000000, 8 MB
BIOS Flash E28F640J3 @ 0xfffd8000, 128KB
0: ethernet0: the address is 0011.937e.0486, irq 9
1: ethernet1: the address is 0011.937e.0487, irq 10
Features licensed:
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
The maximum physical Interfaces: 2
Maximum Interfaces: 2
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal guests: 10
Throughput: unlimited
Peer IKE: 10
This PIX has a restricted license (R).
Serial number: 808301473 (0x302db3a1)
Activation key running: 0xb53be54d 0x26da18f9 0xb2b78cef 0x8fe1abb6
Configuration changed from enable_1 to 15:36:42.554 UTC, Monday, November 8, 2004
pixfirewall >
long live java.
Please this mark as resolved, others won't waste time.
Thank you
-
PIX 501 for Cisco 3640 VPN router
-Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-
Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.
What Miss me? I added the configuration for the PIX and the router.
Here are the PIX config:
PIX Version 6.1 (1)
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable encrypted password xxxxxxxxxxxxxxxx
xxxxxxxxxxxxx encrypted passwd
pixfirewall hostname
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
pager lines 24
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
IP address outside dhcp setroute
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
No sysopt route dnat
Telnet timeout 5
SSH timeout 5
dhcpd address 192.168.1.2 - 192.168.1.33 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
Cryptochecksum:XXXXXXXXXXXXXXXXXXX
: end
Here is the router config
Router #sh runn
Building configuration...
Current configuration: 6500 bytes
!
version 12.2
no service button
tcp KeepAlive-component snap-in service
a tcp-KeepAlive-quick service
horodateurs service debug datetime localtime
Log service timestamps datetime localtime
no password encryption service
!
router host name
!
start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system
queue logging limit 100
activate the password xxxxxxxxxxxxxxxxx
!
clock TimeZone Central - 6
clock summer-time recurring CENTRAL
IP subnet zero
no ip source route
!
!
no ip domain-lookup
!
no ip bootp Server
inspect the name smtp Internet IP
inspect the name Internet ftp IP
inspect the name Internet tftp IP
inspect the IP udp Internet name
inspect the tcp IP Internet name
inspect the name DMZ smtp IP
inspect the name ftp DMZ IP
inspect the name DMZ tftp IP
inspect the name DMZ udp IP
inspect the name DMZ tcp IP
audit of IP notify Journal
Max-events of po verification IP 100
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 20
BA 3des
preshared authentication
Group 2
ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx
ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test
Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT
!
dynamic-map crypto dny - Sai 25
game of transformation-PIXRMT
match static address PIX1
!
!
static-card 10 map ipsec-isakmp crypto
the value of x.x.180.133 peer
the transform-set vpn-test value
match static address of Hunt
!
map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc
!
call the rsvp-sync
!
!
!
controller T1 0/0
framing ESF
linecode b8zs
Slots 1-12 channels-group 0 64 speed
Description controller to the remote frame relay
!
controller T1 0/1
framing ESF
linecode b8zs
Timeslots 1-24 of channel-group 0 64 speed
Description controller for internet link SBIS
!
interface Serial0/0:0
Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites
bandwidth 768
no ip address
no ip redirection
no ip unreachable
no ip proxy-arp
encapsulation frame-relay
frame-relay lmi-type ansi
!
interface Serial0 / point to point 0:0.17
Description Frame Relay to xxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 17 frame relay interface
!
interface Serial0 / point to point 0:0.18
Description Frame Relay to xxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 18 frame relay interface
!
interface Serial0 / point to point 0:0.19
Description Frame Relay to xxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 19 frame relay interface
!
interface Serial0 / point to point 0:0.20
Description Frame Relay to xxxxxxxxxxxxx location
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 20 frame relay interface
!
interface Serial0 / point to point 0:0.21
Description Frame Relay to xxxxxxxxxxxx
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 21 frame relay interface
!
interface Serial0 / point to point 0:0.101
Description Frame Relay to xxxxxxxxxxx
IP unnumbered Ethernet1/0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
No arp frame relay
dlci 101 frame relay interface
!
interface Serial0/1:0
CKT ID 14.HCGS.785383 T1 to ITT description
bandwidth 1536
IP address x.x.76.14 255.255.255.252
no ip redirection
no ip unreachable
no ip proxy-arp
NAT outside IP
inspect the Internet IP on
no ip route cache
card crypto ISCMAP
!
interface Ethernet1/0
IP 10.1.1.1 255.255.0.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
no ip route cache
no ip mroute-cache
Half duplex
!
interface Ethernet2/0
IP 10.100.1.1 255.255.0.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
no ip route cache
no ip mroute-cache
Half duplex
!
router RIP
10.0.0.0 network
network 192.168.1.0
!
IP nat inside source list 112 interface Serial0/1: 0 overload
IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible
IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible
IP nat inside source 10.1.3.2 static 209.184.71.140
IP nat inside source static 10.1.3.6 209.184.71.139
IP nat inside source static 10.1.3.8 209.184.71.136
IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible
IP classless
IP route 0.0.0.0 0.0.0.0 x.x.76.13
IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19
IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18
IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17
IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20
IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21
IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101
no ip address of the http server
!
!
PIX1 static extended IP access list
IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255
IP access-list extended hunting-static
IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255
extended IP access vpn-static list
ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255
IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255
access-list 1 refuse 10.0.0.0 0.255.255.255
access-list 1 permit one
access-list 12 refuse 10.1.3.2
access-list 12 allow 10.1.0.0 0.0.255.255
access-list 12 allow 10.2.0.0 0.0.255.255
access-list 12 allow 10.3.0.0 0.0.255.255
access-list 12 allow 10.4.0.0 0.0.255.255
access-list 12 allow 10.5.0.0 0.0.255.255
access-list 12 allow 10.6.0.0 0.0.255.255
access-list 12 allow 10.7.0.0 0.0.255.255
access-list 112 deny ip host 10.1.3.2 everything
access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255
access-list 112 allow ip 10.1.0.0 0.0.255.255 everything
access-list 112 allow ip 10.2.0.0 0.0.255.255 everything
access-list 112 allow ip 10.3.0.0 0.0.255.255 everything
access-list 112 allow ip 10.4.0.0 0.0.255.255 everything
access-list 112 allow ip 10.5.0.0 0.0.255.255 everything
access-list 112 allow ip 10.6.0.0 0.0.255.255 everything
access-list 112 allow ip 10.7.0.0 0.0.255.255 everything
access-list 120 allow ip host 10.100.1.10 10.1.3.7
not run cdp
!
Dial-peer cor custom
!
!
!
!
connection of the banner ^ CCC
******************************************************************
WARNING - Unauthorized USE strictly PROHIBITED!
******************************************************************
^ C
!
Line con 0
line to 0
password xxxxxxxxxxxx
local connection
Modem InOut
StopBits 1
FlowControl hardware
line vty 0 4
exec-timeout 15 0
password xxxxxxxxxxxxxx
opening of session
!
end
Router #.
Add the following to the PIX:
> permitted connection ipsec sysopt
This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.
-
Hello
I have Microsoft CA server with the latest support CEP and pix 501 that gets the digital certificate. I also have the client certificate of Cisco, but VPN doesn't work
In the IPSec Log Viewer, I constantly "CM_IKE_ESTABLISH_FAIL."
It worked well prior to Win2k server has been completely updated with the latest patches.
The pix configuration is identical to that of article http://www.cisco.com/warp/public/471/configipsecsmart.html
I reinstall the stand-alone CA and support CEP server but not had any luck.
What could be wrong?
It looks like IKE implementation problem. Make DH group 2 policy ISAKMP.
Visit this link:
http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_v53/IPSec/exvpncl.htm
-
Cisco PIX 501 to Cisco 3005 concentrator via remote access
Hello people,
I need your help.
We got a Cisco PIX 501 in one place and this pix is configured for pppoe connection. The pix connects to internet via the pppoe client. an official ip address ping works well.
So what I want to do is to establish a tunnel von between this pix and a cisco 3005 concentrator.
But I failed to establish it.
Here are the pix config. the acl? s are only for the test and will be replaced if it works.
6.3 (4) version PIX
interface ethernet0 10baset
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the password xxx
passwd xxx
hostname PIX - to THE
domain araukraine.ua
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
outside ip access list allow a whole
inside_access_in ip access list allow a whole
pager lines 24
opening of session
Monitor logging warnings
logging warnings put in buffered memory
MTU outside 1456
MTU inside 1456
IP address outside pppoe setroute
IP address inside 192.168.x.x 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
PDM location 192.168.x.x 255.255.255.224 inside
forest warnings of PDM 500
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
outside access-group in external interface
inside_access_in access to the interface inside group
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
the ssh LOCAL console AAA authentication
Enable http server
255.255.x.x 192.168.x.x http inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
255.255.x.x telnet inside 192.168.x.x
Telnet timeout 5
SSH 194.39.97.0 255.255.255.0 outside
SSH timeout 5
management-access inside
Console timeout 0
VPDN group pppoe_group request dialout pppoe
VPDN group pppoe_group localname [email protected] / * /
VPDN group ppp authentication pap pppoe_group
VPDN username [email protected] / * / password *.
encrypted privilege 15
vpnclient Server 212.xx.xx.xx
vpnclient mode network-extension-mode
vpntest vpngroup vpnclient password *.
vpnclient username pixtest password *.
Terminal width 80
the hub, I created a user pixtest, a group vpntest and I? ve created the rules of the network for example to what server, users behind the pix will be able to access.
And that? s all.
I couldn't send you exit pix or hub because I don't have an error or a message that the tunnel will be established.
What can be wrong?
Thanks for the replies
This configuration example shows how to create an IPsec tunnel to a computer that is running the Client VPN Cisco's (4.x and later versions) to a Cisco VPN concentrator 3000 to allow the user to safely access the network inside the VPN concentrator.
-
PIX 501 and VPN Linksys router (WRV200)
I inherited a work where we have a Cisco PIX 501 firewall to a single site and Linksys WRV200 Router VPN on two other
sites. Asked me to connect these routers Linksys firewall PIX via the VPN.
According to me, the Linksys vpn routers can only connect via IPSec VPN, I'm looking for help on the configuration of the PIX 501 for the linksys to connect with the following, if possible.
Key exchange method: Auto (IKE)
Encryption: Auto, 3DES, AES128, AES192, AES256
Authentication: MD5
Pre Shared Key: xxx
PFS: Enabled
Life ISAKMP key: 28800
Life of key IPSec: 3600
The pix, I installed MDP and I tried to use the VPN wizard without result.
I chose the following settings when you make the VPN Wizard:
Type of VPN: remote VPN access
Interface: outside
Type of Client VPN device used: Cisco VPN Client
(can choose customer of Cisco VPN 3000, MS Windows Client by using the client MS Windows using L2TP, PPTP)
VPN clients group
Name of Group: RabyEstates
Pre Shared Key: rabytest
Scope of the Client authentication: disabled
Address pool
Name of the cluster: VPN - LAN
Starter course: 192.168.2.200
End of row: 192.168.2.250
Domain DNS/WINS/by default: no
IKE policy
Encryption: 3DES
Authentication: MD5
Diffie-Hellman group: Group 2 (1024 bits)
Transform set
Encryption: 3DES
Authentication: MD5
I have attached the log of the VPN Linksys router VPN.
This is the first time that I have ever worked with PIX so I'm still trying to figure the thing to, but I'm confident with the CCNA level network.
Thanks for your help!
Hello
Everything looks fine for me, try to have a computer in every network and ping between them. Check the newspapers/debug and fix them.
Let me know.
See you soon,.
Daniel
-
VPN PPTP and PPPOE CLIENT ON PIX 501
Hello
Can I create a PPTP VPN and a client connection on a PIX 501 with a client to my ISP PPPOE connection. The PPPOE ip is dynamic and the VPN will be a static IP address. They gave me a username and password for VPN and PPPOE. Him also gave me an ip address for the VPN server.
Should that happen, it's that the PPPOE should connect to the VPN to work.
I can only get the PPPOE, but I don't know how to do this with a PPTP VPN set.
Here is my config:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password xxxxxxxx encrypted
passwd xxxxxxx encrypted
hostname neveroff
domain-name neveroff.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list incoming permit icmp any any echo-reply
access-list incoming permit icmp any any source-quench
access-list incoming permit icmp any any unreachable
access-list incoming permit icmp any any time-exceeded
pager lines 24
icmp permit any echo outside
icmp permit any unreachable outside
icmp permit any time-exceeded outside
icmp permit any source-quench outside
icmp permit any echo-reply outside
icmp permit any information-reply outside
icmp permit any mask-reply outside
icmp permit any timestamp-reply outside
mtu outside 1500
mtu inside 1500
ip address outside pppoe setroute
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 192.168.1.0 255.255.255.0 0 0
static (inside,outside) tcp interface smtp 192.168.1.201 smtp netmask 255.255.255.255 0 0
access-group incoming in interface outside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 5
console timeout 0
vpdn group pppoex request dialout pppoe
vpdn group pppoex localname xxxxxxxxx
vpdn group pppoex ppp authentication chap
vpdn username xxxxxxxx password xxxxxxxx
dhcpd address 192.168.1.10-192.168.1.41 inside
dhcpd dns 192.168.1.1 168.210.2.2
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
username neveroff password TEnlGTQMwqamBzMn encrypted privilege 2
terminal width 80
Cryptochecksum:c5bfafa70f21ed55cc1b3df377e110bf
: end
Thank you
Etienne
Happy to help and please kindly mark the message as answered if you have not more than other questions. Thank you.
-
PIX 501 NAT and PAT with a single IP address
Using the following configuration, on my first PIX 501, I am unable to provide a server of mail to the outside world and allows inside customers to browse the Internet. :
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable password xxxx
passwd xxx
hostname fw-sam-01
SAM domain name
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
No fixup not protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
outside access list permit tcp any host 62.x.x.109 eq smtp
access the inside to allow tcp a whole list
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside the 62.177.x.x.x.255.248
IP address inside 192.168.45.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
location of PDM 192.168.45.2 255.255.255.255 inside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
public static 62.177.x.x.x.45.2 (Interior, exterior) mask subnet 255.255.255.255 0 0
outside access-group in external interface
group-access to the Interior in the interface inside
Route outside 0.0.0.0 0.x.x.x.177.208.105 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.45.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Telnet 192.168.45.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd lease 3600
dhcpd ping_timeout 750
: end
It is I'am using access list and groups wrong or am I wrong in PAT/NAT configuration.
Please advise...
Hello
I went through the ongoing discussion. The pix configuration should be fine for now according to suggestions. The problems seems to be on the server. If it is a new installation of windows, then there is an option not to accept requests that are not local network.
If you want to check if pix allows connections and then when you telnet to port 25 of the outside, just run the xlates control.
SH xlate and it should show you a translation for the inside host. More than a quick test if pix allows traffic is to check 'sho-outdoor access list' and see if the counters are increasing.
Hopefully this should help you.
Arun S.
-
I'm setting up a cisco pix 501 vpn tunnel but will have questions. The Firewall works although I am able to get out of the internet, but the VPN does not work. On the primary side, I see that the tunnel is up and the traffic is sent but not received.
Currently I'm sitting at the secondary location but don't know what the problem maybe. Anyone know what I have wrong which could prevent the data to send from this device?
Here is my config
Here's my config if it would help
See the race
: Saved
:
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 2KFQnbNIdI.2KYOU encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
hostname ciscofirewall
domain hillsanddales.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 5
fixup protocol rtsp 55
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list 101 permit ip 192.168.80.0 255.255.255.0 192.168.50.0 255.255.255.0
192.168.80.0 IP Access-list sheep 255.255.255.0 allow 192.168.50.0 255.255.255.0
in_outside list access permit tcp any host 192.168.50.240
in_outside list access permit tcp any host 64.90.xxx.xx
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside 66.84.xxx.xx 255.255.255.252
IP address inside 192.168.80.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
location of PDM 192.168.50.0 255.255.255.0 outside
location of PDM 192.168.80.2 255.255.255.255 inside
location of PDM 192.168.50.0 255.255.255.0 inside
location of PDM 182.168.80.0 255.255.255.255 inside
location of PDM 0.0.0.0 255.255.255.0 inside
location of PDM 0.0.0.0 255.255.255.255 inside
location of PDM 192.168.80.5 255.255.255.255 inside
location of PDM 192.168.80.7 255.255.255.255 inside
PDM logging 100 information
history of PDM activateARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 66.84.xxx.x
Route inside 192.168.50.0 255.255.255.0 192.168.50.240 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.80.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
<--- more="" ---="">Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-md5-hmac aptset
aptmap 10 ipsec-isakmp crypto map
correspondence address card crypto aptmap 10 101
card crypto aptmap 10 peers set 64.90.xxx.xx
card crypto aptmap 10 transform-set aptset
aptmap interface card crypto outside
ISAKMP allows outside
ISAKMP key * address 64.90.xxx.xx netmask 255.255.255.255
ISAKMP identity address
ISAKMP nat-traversal 20
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
Telnet 192.168.80.2 255.255.255.255 inside
Telnet 182.168.80.0 255.255.255.255 inside
Telnet 192.168.80.5 255.255.255.255 inside
Telnet 192.168.80.0 255.255.255.0 inside
Telnet 192.168.80.7 255.255.255.255 inside
Telnet timeout 5
SSH timeout 5
management-access insideConsole timeout 0
dhcpd address 192.168.80.2 - 192.168.80.33 inside
dhcpd dns 64.90.xxx.xx 64.90.xxx.xx
dhcpd lease 3600
dhcpd ping_timeout 750--->
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
Cryptochecksum:01532689fac9491fae8f86e91e2bd4c0
: endHello
At least the NAT0 ACL is not in use
You should have this added to the configuration
NAT (inside) 0 access-list sheep
-Jouni
-
Customer Cisco PIX 501 VPN connects but no connection to the local network
Hi all:
I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.
I have attached the PIX configuration.
Advice will be greatly appreciated.
********************
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable password xxxx
passwd xxxxx
pixfirewall hostname
domain ciscopix.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside dhcp setroute
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool ippool 192.168.2.1 - 192.168.2.5
location of PDM 192.168.2.0 255.255.255.0 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) - 0 102 access list
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
Crypto-map dynamic dynmap 10 transform-set RIGHT
map mymap 10-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup vpn3000 ippool address pool
vpngroup vpn3000 Server dns 68.87.72.130
vpngroup vpn3000-wins 192.168.1.100 Server
vpngroup vpn3000 split tunnel 101
vpngroup vpn3000 downtime 1800
password vpngroup vpn3000 *.
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.1.2 - 192.168.1.33 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
Cryptochecksum:xxxx
****************
The DNS server is the one assigned to me by my ISP.
My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5
"isakmp nat-traversal 20" can do the trick.
-
PIX 501 and THE, 3DES, AES
For a version newly produced PIX 501,
(1) are DES, 3DES and AES activation keys all pre-installed?
(2) how I can find on which of them is pre-installed on my PIX 501?
(3) when I create a server VPN (on the PIX 501), I see that all three OF THEM, 3DES and AES are available in the drop-down list of the PDM configuration screen. Does that mean my PIX 501 have all three of them (FROM THE, 3DES and AES)? -If the answer is no, assume that only is preinstalled on PIX 501, then why/how can appear in the drop-down list the 3DES and AES?
Thank you for helping.
Scott
Should be integrated already. depends on the way the news is your PIX 501.
To be sure to log in to the console and type:
See the version
See the example output version:
See the pixfirewall version (config) #.
Cisco PIX Firewall Version 6.2 (3)
Cisco PIX Device Manager Version 2.0 (1)
Updated Thursday April 17 02 21:18 by Manu
pixdoc515 up to 9 days 3 hours
Material: PIX - 515, 64 MB RAM, Pentium 200 MHz processor
I28F640J5 @ 0 x 300 Flash, 16 MB
BIOS Flash AT29C257 @ 0xfffd8000, 32 KB
0: ethernet0: the address is 0050.54ff.3772, irq 10
1: ethernet1: the address is 0050.54ff.3773, irq 7
2: ethernet2: the address is 00d0.b792.409d, irq 11
Features licensed:
Failover: enabled
VPN - A: enabled
VPN-3DES: enabled
Maximum Interfaces: 6
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: unlimited
Throughput: unlimited
Peer IKE: unlimited
Serial number: 480221353 (0x1c9f98a9)
Activation key running: 0x36df4255 0x246dc5fc 0x39d2ec4d 0x09f6288f
Modified configuration of enable_15 to 12:15:28.311 UTC Wednesday, may 1, 2002
pixfirewall (config) #.
Here, you should see if THE or 3DES, AES encryption is active or not. If you have just SOME so you can use the following link and get for free a new activation key that allows 3DES and AES.
https://Tools.Cisco.com/swift/licensing/JSP/formGenerator/Pix3DesMsgDisplay.jsp
sincerely
Patrick
-
I try to get my PIX 501 to forward traffic on port 1412 with TCP and UDP to use Direct Connect, and the problem I have is I can connect to a DC hub, but cannot establish connections with users.
I added the following to the default configuration from the factory with a partial success:
outside access list permit tcp any host 192.168.100.20 eq 1412
access-list outside permit udp any host 192.168.100.20 eq 1412
public static tcp (indoor, outdoor) interface 1412 192.168.100.20 1412 netmask 255.255.255.255 0 0
public static tcp (indoor, outdoor) interface 1412 192.168.100.20 1412 netmask 255.255.255.255 0 0
In the debug log set to the access list I rule this type of errors:
Deny tcp src outside other.users.ip.addr/3099 dst within the my.public.ip.addr/1412 by access-group "access_outside_in".
TCP request discarded outside my.public.ip.addr/45961 other.users.ip.addr/2362
I'm quite lost as to why it does not work when I think it should. I tried several ways, opening of port ranges and no chance for a transfer of the port sucsessful.
You can change you, outside the ACL to the following:
outside access list permit tcp any host eq 1412
access-list outside permit udp any host eq 1412
outside access-group in external interface
Save again with: write mem and also issue: clear xlate
I would like to know if it works.
Jay
Maybe you are looking for
-
How to build an equation with variables
I want to solve an equation below shows zero finder vi by the Newton Raphson: z a * b * c * exp(-z/a),. a, b, and c are variables I can build the equation with constant a, b, c, but how do I build it? Thank you very much!
-
the Information\_restore{106cf321-99A3-4E3A-9103-1BD02760-6A99}\rp687 Volume of c:\System file or directory is corrupted and unreadable. Run the chkdsk utility. I tried to run chkdsk but it does not work. I can't start the defragmentation either. I t
-
I NEED an operating system?
Hello, at the moment I'm building a computer. What I was wondering is, are you able to run a computer normally without OS? If I could, I'd still be able to do things such as running iTunes, play music, watch videos, play games and so on? I think to i
-
Hello can I put an msata module in my HP ENVY 15 j104el?
-
why it gives me this warning and what can I do to save my info before this thing crashes?
He told me to save my info that there is a problem with my C, D, G on my Toshiba MK6465GSX ATA device. I have that dvd rw to back up my info on who it is urgent suggesting that I do. I backed up to disk until I don't have a flash drive and when he w