VPN tunnel is up but cannot ping LAN stations

Similar Questions

• Remote access VPN client to connect but cannot ping inside the host, after that split tunnel is activated (config-joint)

  Hello

  I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.

  is hell config please kindly and I would like to know what might happen.

  hostname horse

  domain evergreen.com

  activate 2KFQnbNIdI.2KYOU encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  ins-guard

  !

  interface GigabitEthernet0/0

  LAN description

  nameif inside

  security-level 100

  192.168.200.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/1

  Description CONNECTION_TO_FREEMAN

  nameif outside

  security-level 0

  IP 196.1.1.1 255.255.255.248

  !

  interface GigabitEthernet0/2

  Description CONNECTION_TO_TIGHTMAN

  nameif backup

  security-level 0

  IP 197.1.1.1 255.255.255.248

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  Shutdown

  No nameif

  no level of security

  no ip address

  management only

  !

  boot system Disk0: / asa844-1 - k8.bin

  boot system Disk0: / asa707 - k8.bin

  passive FTP mode

  clock timezone WAT 1

  DNS server-group DefaultDNS

  domain green.com

  network of the NETWORK_OBJ_192.168.2.0_25 object

  Subnet 192.168.2.0 255.255.255.128

  network of the NETWORK_OBJ_192.168.202.0_24 object

  192.168.202.0 subnet 255.255.255.0

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  the DM_INLINE_NETWORK_1 object-group network

  object-network 192.168.200.0 255.255.255.0

  object-network 192.168.202.0 255.255.255.0

  the DM_INLINE_NETWORK_2 object-group network

  object-network 192.168.200.0 255.255.255.0

  object-network 192.168.202.0 255.255.255.0

  access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

  access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

  Access extensive list permits all ip a OUTSIDE_IN

  gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

  standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

  gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

  standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  backup of MTU 1500

  mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm-645 - 206.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  !

  network obj_any object

  dynamic NAT interface (inside, backup)

  Access-group interface inside INSIDE_OUT

  Access-group OUTSIDE_IN in interface outside

  Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10

  Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  Enable http server

  http 192.168.200.0 255.255.255.0 inside

  http 192.168.202.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  monitor SLA 100

  type echo protocol ipIcmpEcho 212.58.244.71 interface outside

  Timeout 3000

  frequency 5

  monitor als 100 calendar life never start-time now

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  backup of crypto backup_map interface card

  Crypto ikev1 allow outside

  Crypto ikev1 enable backup

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  !

  track 10 rtr 100 accessibility

  Telnet 192.168.200.0 255.255.255.0 inside

  Telnet 192.168.202.0 255.255.255.0 inside

  Telnet timeout 5

  SSH 192.168.202.0 255.255.255.0 inside

  SSH 192.168.200.0 255.255.255.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 15

  SSH group dh-Group1-sha1 key exchange

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntunnel strategy

  Group vpntunnel policy attributes

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntunnel_splitTunnelAcl

  field default value green.com

  internal vpntunnell group policy

  attributes of the strategy of group vpntunnell

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl

  field default value green.com

  Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password

  attributes of user name THE

  VPN-group-policy gbnlvpn

  tunnel-group vpntunnel type remote access

  tunnel-group vpntunnel General attributes

  address VPNPOOL pool

  strategy-group-by default vpntunnel

  tunnel-group vpntunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  type tunnel-group vpntunnell remote access

  tunnel-group vpntunnell General-attributes

  address VPNPOOL2 pool

  Group Policy - by default-vpntunnell

  vpntunnell group of tunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns migrated_dns_map_1

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the migrated_dns_map_1 dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565

  Hello

  1 - Please run these commands:

  "crypto isakmp nat-traversal 30.

  "crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.

  The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.

  Please let me know.

  Thank you.

• VPN connection is established but cannot ping subnet

  Hello, I have a 851 router that I'm trying to learn with, I have a config of work that makes me online and has a basic firewall and dhcp for clients. Then, I wanted to add a VPN using the 851 and the Cisco VPN client.

  Using this tutorial "http://www.cisco.com/en/US/customer/products/sw/secursw/ps5318/products_configuration_example09186a00806ad10e.shtml."

  I was able to get partially to my goal as I can establish a vpn and it shows me 192.168.1.0 as the route secure, but I don't ping or communicate with anything with in the 192.168.1.1 network.

  Try this one too.

  Instead of using access-list in declaration of NAT, use the route map and see if it solves the problem.

  1 deny traffic Ipsec in NAT access list.

  access-list 120 refuse 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 120 allow 192.168.1.0 0.0.0 all

  2. create a roadmap

  sheep allowed 10 route map

  corresponds to the IP 120

  3. no nat ip within the source list 1 interface FastEthernet4 overload

  4 ip nat inside source map route sheep interface FastEthernet4 overload

  5 disable the ip nat translation *.

  Then check.

  HTH

  Sangaré

• Problem with Site-to-Site VPN. VPN tunnel is broken but can ping

  OK, so I am trying to understand why I can't not only appears when I sh crypto isakmp his or sh crypto ipsec his. I did the basic to site vpn settings to another and I can't ping on both networks fine no problem. So, when I ping from one pc to the address 172.16.0.0 192.168.0.0 network network there is no problem at all because the pings are very well received. But when I go to sh crypto isakmp sa, there's simply nothing and I can't for the life of understand me why. I watched my sh run for both routers and all seems well, but I guess I could be overlooking something. I would really appreciate if someone could help me to diagnose this problem.

  I've attached my plotter file of package and two routers use the binary password. I also have the sh run two routers also attached.

  I'm not on any of the router 172.16.0.0/24 only 172.16.0.0/16 and I think that is the question.

  In Crypto ACL you have on the router of branch:

  !

  S2S-VPN-TRAFFIC extended IP access list

  Licensing ip 192.168.0.0 0.0.0.255 172.16.0.0 0.0.0.255

  If it should not be:

  !

  S2S-VPN-TRAFFIC extended IP access list

  Licensing ip 192.168.0.0 0.0.0.255 172.16.0.0 0.0.255.255

  and coursed mirrored on the main router.

  If this isn't the case, you are saying that some ping between 192.168.0.x and 172.16.0.x is going ok. Can you please indicate exactly that one? I could see that you have attached a package tracer, but I couldn't open it.

• VPN tunnel look up but no ping

  Hello

  I got a pix that had two tunnels of work will a 5510 and a single 5520. Today the tunnel VPN to our 5520 has stopped working but if I sh shout to isa its two tunnels were QM_IDLE for the State. (both ends) I tried to debug crypto isakmp 255 but all I get is PEER_REAPER_TIMER and no other output on the side of pix.

  I'm looking for commands or something to try that might help...

  This ACL line overlaps Cryptography real ACL 'Outside_cryptomap_20 '.

  Outside_cryptomap_10 list extended access permits ip data center-Interior - 255.255.254.0 AC office network 255.255.255.0

  Please please delete above the line, then disable all tunnels so he renegotiates the SA correct.

• Connected to the ASA via the "VPN Client" software, but cannot ping devices.

  I have a network that looks like this:

  

  I successfully connected inside the ASA via a software "Client VPN" tunnel network and got an IP address of 10.45.99.100/16.

  I am trying to ping the 10.45.99.100 outside 10.45.7.2, but the ping fails (request timed out).

  On the SAA, including the "logging console notifications" value, I notice the following message is displayed:

  "% 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; "Connection for icmp src, dst outside: 10.45.99.100 inside: 10.45.7.2 (type 8, code 0) rejected due to the failure of reverse path of NAT.

  I have a vague feeling that I'm missing a NAT rule of course, but not all. What did I miss?

  Here is my configuration of ASA: http://pastebin.com/raw.php?i=ad6p1Zac

  Hello

  You seem to have a configured ACL NAT0 but is not actually in use with a command "nat"

  You would probably need

  NAT (inside) 0-list of access inside_nat0_outside

  He must manage the NAT0

  Personally, I would avoid using large subnets/networks. You probably won't ever have host behind ASA who would fill / 16 subnet mask.

  I would also keep the pool VPN as a separate network from LANs behind ASA. The LAN 10.45.0.0/16 and 10.45.99.100 - 200 are on the same network.

  -Jouni

• ASA 5520: Remote VPN Clients cannot ping LAN, Internet

  I've set up a few of them in my time, but I am confused with this one.  Can I establish connect via VPN tunnel but I can't ping or go on the internet.  I searched the forum for similar and found a little issues, but none of the fixes seem to match.  I noticed a strange thing is when I run ipconfig/all of the vpn client, the IP address that has been leased over the Pool of the VPN is also the default gateway!

  I have attached the config.  Help, please.

  Thank you!

  Exemption of NAT ACL has not yet been applied.

  NAT (inside) 0-list of access Inside_nat0_outbound

  In addition, you have not split tunnel, not sure you were using internet ASA for the vpn client internet browsing.

  You can also enable icmp inspection if you test in scathing:

  Policy-map global_policy
  class inspection_default

  inspect the icmp

  Hope that helps.

• VPN connects but cannot ping or access resources

  I hope this is an easy fix and it's something that I am missing.  I've been looking at this for several hours.

  Scenario:

  I Anyconnect Essentials so I use the SSL connection

  I changed my domain name and external IP in my setup, I write.

  My VPN connection seems to work very well.  In fact, I was able to connect to 3 locations with 3 different external IP address.

  1 location, I get IP address 192.168.30.10, as it should.  I can ping 192.168.1.1, but not the 192.168.1.6 which is my temporary resource, the firewall is disabled on 192.168.1.6.

  2 location, I get an IP of 192.168.30.11, as it should.  I was able to ping 192.168.30.10, could not sue 192.168.1.1 as the place closed.

  Any help would be appreciated, it's getting late so I hope I gave enough details.  I feel so close but yet so far.

  See the ciscoasa # running

  : Saved

  :

  ASA Version 8.2 (1)

  !

  ciscoasa hostname

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 22.22.22.246 255.255.255.252

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  clock timezone CST - 6

  clock to summer time recurring CDT

  DNS lookup field inside

  DNS domain-lookup outside

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  ICMP-type of object-group ALLOWPING

  echo ICMP-object

  ICMP-object has exceeded the time

  response to echo ICMP-object

  Object-ICMP traceroute

  Object-ICMP source-quench

  ICMP-unreachable object

  access-list 10 scope ip allow a whole

  10 extended access-list allow icmp a whole

  pager lines 24

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  mask 192.168.30.10 - 192.168.30.25 255.255.255.0 IP local pool SSLClientPoolNew

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 192.168.1.0 255.255.255.0

  Route outside 0.0.0.0 0.0.0.0 22.22.22.245 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  network-acl 10

  WebVPN

  SVC request no svc default

  AAA authentication LOCAL telnet console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  management-access inside

  dhcpd dns 8.8.8.8

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow inside

  allow outside

  AnyConnect essentials

  SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 1 image

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 2 image

  enable SVC

  tunnel-group-list activate

  internal SSLClientPolicy group strategy

  attributes of Group Policy SSLClientPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  field default value mondomaine.fr

  the address value SSLClientPoolNew pools

  WebVPN

  SVC Dungeon-Installer installed

  time to generate a new key of SVC 180

  SVC generate a new method ssl key

  SVC value vpngina modules

  attributes of Group Policy DfltGrpPolicy

  VPN-tunnel-Protocol webvpn

  username test encrypted password privilege 15 xxxxxxxxxxxxxx

  username ljb1 password encrypted xxxxxxxxxxxxxx

  type tunnel-group SSLClientProfile remote access

  attributes global-tunnel-group SSLClientProfile

  Group Policy - by default-SSLClientPolicy

  tunnel-group SSLClientProfile webvpn-attributes

  enable SSLVPNClient group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  Policy-map global_policy

  class inspection_default

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:ed683c7f1b86066d1d8c4fff6b08c592

  : end

  Patrick,

  'Re missing you the excemption NAT. Please add the following and try again:

  access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.30.0 255.255.255.0

  NAT (inside) 0 access-list sheep

  Let us know if you still have problems after that.

  Raga

• Cisco ASA 5515 - Anyconnect users can connect to ASA, but cannot ping inside the local IP address

  Hello!

  I have a 5515 ASA with the configuration below. I have configure the ASA as remote access with anyconnect VPN server, now my problem is that I can connect but I can not ping.

  ASA Version 9.1 (1)

  !

  ASA host name

  domain xxx.xx

  names of

  local pool VPN_CLIENT_POOL 192.168.12.1 - 192.168.12.254 255.255.255.0 IP mask

  !

  interface GigabitEthernet0/0

  nameif inside

  security-level 100

  192.168.11.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/1

  Description Interface_to_VPN

  nameif outside

  security-level 0

  IP 111.222.333.444 255.255.255.240

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  management only

  nameif management

  security-level 100

  192.168.5.1 IP address 255.255.255.0

  !

  passive FTP mode

  DNS server-group DefaultDNS

  www.ww domain name

  permit same-security-traffic intra-interface

  the object of the LAN network

  subnet 192.168.11.0 255.255.255.0

  LAN description

  network of the SSLVPN_POOL object

  255.255.255.0 subnet 192.168.12.0

  VPN_CLIENT_ACL list standard access allowed 192.168.11.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  management of MTU 1500

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 711.bin

  don't allow no asdm history

  ARP timeout 14400

  no permit-nonconnected arp

  NAT (exterior, Interior) static source SSLVPN_POOL SSLVPN_POOL static destination LAN LAN

  Route outside 0.0.0.0 0.0.0.0 111.222.333.443 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  WebVPN

  list of URLS no

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  AAA authentication http LOCAL console

  LOCAL AAA authorization exec

  Enable http server

  http 192.168.5.0 255.255.255.0 management

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec pmtu aging infinite - the security association

  Crypto ca trustpoint ASDM_TrustPoint5

  Terminal registration

  E-mail [email protected] / * /

  name of the object CN = ASA

  address-IP 111.222.333.444

  Configure CRL

  Crypto ca trustpoint ASDM_TrustPoint6

  Terminal registration

  domain name full vpn.domain.com

  E-mail [email protected] / * /

  name of the object CN = vpn.domain.com

  address-IP 111.222.333.444

  pair of keys sslvpn

  Configure CRL

  trustpool crypto ca policy

  string encryption ca ASDM_TrustPoint6 certificates

  Telnet timeout 5

  SSH 192.168.11.0 255.255.255.0 inside

  SSH timeout 30

  Console timeout 0

  No ipv6-vpn-addr-assign aaa

  no local ipv6-vpn-addr-assign

  192.168.5.2 management - dhcpd addresses 192.168.5.254

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL-trust outside ASDM_TrustPoint6 point

  WebVPN

  allow outside

  CSD image disk0:/csd_3.5.2008-k9.pkg

  AnyConnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client

  internal VPN_CLIENT_POLICY group policy

  VPN_CLIENT_POLICY group policy attributes

  WINS server no

  value of server DNS 192.168.11.198

  VPN - 5 concurrent connections

  VPN-session-timeout 480

  client ssl-VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_CLIENT_ACL

  myComp.local value by default-field

  the address value VPN_CLIENT_POOL pools

  WebVPN

  activate AnyConnect ssl dtls

  AnyConnect Dungeon-Installer installed

  AnyConnect ssl keepalive 20

  time to generate a new key 30 AnyConnect ssl

  AnyConnect ssl generate a new method ssl key

  AnyConnect client of dpd-interval 30

  dpd-interval gateway AnyConnect 30

  AnyConnect dtls lzs compression

  AnyConnect modules value vpngina

  value of customization DfltCustomization

  internal IT_POLICY group policy

  IT_POLICY group policy attributes

  WINS server no

  value of server DNS 192.168.11.198

  VPN - connections 3

  VPN-session-timeout 120

  Protocol-tunnel-VPN-client ssl clientless ssl

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_CLIENT_ACL

  field default value societe.com

  the address value VPN_CLIENT_POOL pools

  WebVPN

  activate AnyConnect ssl dtls

  AnyConnect Dungeon-Installer installed

  AnyConnect ssl keepalive 20

  AnyConnect dtls lzs compression

  value of customization DfltCustomization

  username vpnuser password PA$ encrypted $WORD

  vpnuser username attributes

  VPN-group-policy VPN_CLIENT_POLICY

  type of remote access service

  Username vpnuser2 password PA$ encrypted $W

  username vpnuser2 attributes

  type of remote access service

  username admin password ADMINPA$ $ encrypted privilege 15

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address VPN_CLIENT_POOL pool

  Group Policy - by default-VPN_CLIENT_POLICY

  VPN Tunnel-group webvpn-attributes

  the aaa authentication certificate

  enable VPN_to_R group-alias

  type tunnel-group IT_PROFILE remote access

  attributes global-tunnel-group IT_PROFILE

  address VPN_CLIENT_POOL pool

  Group Policy - by default-IT_POLICY

  tunnel-group IT_PROFILE webvpn-attributes

  the aaa authentication certificate

  enable IT Group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  : end

  Help me please! Thank you!

  Hello

  Please set ACLs to allow ICMP between these two subnets (192.168.11.0 and 192.168.12.0) and check. It should ping. Let me know if it does not work.

  Thank you

  swap

• Cannot ping Lan devices in Vlan

  Hello

  I looked for a solution to this for the week without success. I came across a Cisco C3560, which is used because of its ability of poe to power some Deskphones Voip. While the works of great poe, machines connected to the switch can only communicate with each other and don't can't ping or otherwise access any device connected directly to the router of the network.

  The Cisco switch is configured with a vlan and a default gateway, but nothing comes out by behind the switch. On connected devices can ping by default gateway (192.168.0.1 - a tp-link router), receive a lease dhcp from the router said successfully and can connect to the internet, but on the local network, nothing works. (unable to connect to the printer connetced directly to the router or other computers connected directly to the router.

  Any advice? I am new to cisco switches, don't know what I'm doing here. I'm just trying to get devices that are connected directly to the switch to communicate with devices connected directly to the router.

  Switch#show runBuilding configuration...

  Current configuration : 1528 bytes!version 12.2service configno service padservice timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname Switch!enable secret 5 {}{}{}{}{}{}{}{}{}{}{}{}!no aaa new-modelclock timezone UTC 2system mtu routing 1500ip subnet-zero!!!!no file verify autospanning-tree mode pvstspanning-tree extend system-id!vlan internal allocation policy ascending!interface FastEthernet0/1!interface FastEthernet0/2!interface FastEthernet0/3!interface FastEthernet0/4!interface FastEthernet0/5!interface FastEthernet0/6!interface FastEthernet0/7!interface FastEthernet0/8!interface FastEthernet0/9!interface FastEthernet0/10!interface FastEthernet0/11!interface FastEthernet0/12!interface FastEthernet0/13!interface FastEthernet0/14!interface FastEthernet0/15!interface FastEthernet0/16!interface FastEthernet0/17!interface FastEthernet0/18!interface FastEthernet0/19!interface FastEthernet0/20!interface FastEthernet0/21!interface FastEthernet0/22!interface FastEthernet0/23!interface FastEthernet0/24 switchport mode access!interface GigabitEthernet0/1!interface GigabitEthernet0/2!interface Vlan1 ip address 192.168.0.26 255.255.255.0 no ip route-cache!ip default-gateway 192.168.0.1ip classlessip default-network 192.168.0.0ip http server!access-list 1 permit any log!control-plane!!line con 0line vty 0 4 password XXXXXXXXX login length 0line vty 5 15 password XXXXXXXX login length 0!end

   Switch#show interface

  Vlan1 is up, line protocol is up Hardware is EtherSVI, address is 001e.bd27.c4c0 (bia 001e.bd27.c4c0) Internet address is 192.168.0.26/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 3 packets/sec 138534 packets input, 9472693 bytes, 0 no buffer Received 0 broadcasts (68 IP multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 30296 packets output, 2248820 bytes, 0 underruns 0 output errors, 1 interface resets 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/2 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c484 (bia 001e.bd27.c484) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:56, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 46000 bits/sec, 37 packets/sec 5 minute output rate 582000 bits/sec, 71 packets/sec 1941044 packets input, 327622438 bytes, 0 no buffer Received 38375 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 30699 multicast, 0 pause input 0 input packets with dribble condition detected 3224783 packets output, 2069682884 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out
  
  FastEthernet0/4 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c486 (bia 001e.bd27.c486) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:01, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 129069 packets input, 64947010 bytes, 0 no buffer Received 9953 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9759 multicast, 0 pause input 0 input packets with dribble condition detected 600269 packets output, 45540585 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/6 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c488 (bia 001e.bd27.c488) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:50, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 32693 packets input, 4244428 bytes, 0 no buffer Received 9942 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9759 multicast, 0 pause input 0 input packets with dribble condition detected 588460 packets output, 45003331 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/8 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48a (bia 001e.bd27.c48a) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:30, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 32694 packets input, 4243413 bytes, 0 no buffer Received 9934 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9757 multicast, 0 pause input 0 input packets with dribble condition detected 588485 packets output, 45009466 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/12 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48e (bia 001e.bd27.c48e) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:28, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 32742 packets input, 4252075 bytes, 0 no buffer Received 9947 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9763 multicast, 0 pause input 0 input packets with dribble condition detected 588497 packets output, 45019272 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/13 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c48f (bia 001e.bd27.c48f) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:13, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 148160 packets input, 73818106 bytes, 0 no buffer Received 9973 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9760 multicast, 0 pause input 0 input packets with dribble condition detected 599666 packets output, 49045070 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/14 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c490 (bia 001e.bd27.c490) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:05, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 129165 packets input, 68409495 bytes, 0 no buffer Received 9982 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 9773 multicast, 0 pause input 0 input packets with dribble condition detected 600283 packets output, 45551497 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/18 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c494 (bia 001e.bd27.c494) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:49, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 21000 bits/sec, 18 packets/sec 5 minute output rate 13000 bits/sec, 16 packets/sec 606386 packets input, 88151136 bytes, 0 no buffer Received 159883 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 55198 multicast, 0 pause input 0 input packets with dribble condition detected 941617 packets output, 308269004 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/20 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c496 (bia 001e.bd27.c496) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:54, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 1000 bits/sec, 1 packets/sec 5 minute output rate 1000 bits/sec, 2 packets/sec 515813 packets input, 87006769 bytes, 0 no buffer Received 21466 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 19952 multicast, 0 pause input 0 input packets with dribble condition detected 1858112 packets output, 1700009146 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  FastEthernet0/24 is up, line protocol is up (connected) Hardware is Fast Ethernet, address is 001e.bd27.c49a (bia 001e.bd27.c49a) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:01, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 1 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 546556 packets output, 41182636 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out

  GigabitEthernet0/1 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 001e.bd27.c481 (bia 001e.bd27.c481) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 556000 bits/sec, 83 packets/sec 5 minute output rate 76000 bits/sec, 63 packets/sec 4457827 packets input, 3961330567 bytes, 0 no buffer Received 15028 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 11213 multicast, 0 pause input 0 input packets with dribble condition detected 3822373 packets output, 728132696 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out
  
  

  Switch#show vlan

  VLAN Name     Status         Ports---- -------------------------------- --------- -------------------------------1     default active    Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16                        Fa0/17, Fa0/18, Fa0/19, Fa0/20, Fa0/21, Fa0/22, Fa0/23, Fa0/24, Gi0/1, Gi0/21002 fddi-default act/unsup1003 token-ring-default act/unsup1004 fddinet-default act/unsup1005 trnet-default act/unsup

  VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------1 enet 100001 1500 - - - - - 0 01002 fddi 101002 1500 - - - - - 0 01003 tr 101003 1500 - - - - - 0 01004 fdnet 101004 1500 - - - ieee - 0 01005 trnet 101005 1500 - - - ibm - 0 0

  Remote SPAN VLANs------------------------------------------------------------------------------

  Primary Secondary Type Ports------- --------- ----------------- ------------------------------------------

  Hello

  first thing, please edit your post and remove your remote vty lines access password

  never send passwords on a public forum for the just in case production equipment

  line vty 0 4
  password xxxxxx

  ***********************

  Your question

  What is the configuration of the router as a switch which seems to work correctly you're saying and I configured its doing its job, don't forget you said that you cannot route no between the router and the router switch should take care of this, whats the vlan ports on the router are on is - what the same subnet do they get an ip address in the same subnet off dhcp as devices of switching, if they do, and you cannot ping them to the same subnet theres something upward on the side of the router it would treat for layer 3 routing ip traffic

  the ping to the router devices connected to the cisco switch and can the device on the router cannot ping devices switches

  If you move a device out of the router and attach it to the doe sit switch still work ok, reach the talk of the internet to other devices on the switch?

  As there is a layer 2 switch you don't need this command you have your entry door you can remove it.. .IP default-network 192.168.0.0

• VPN tunnel is up, but traffic will not travel

  Does not include why it does not work. I perform extended ping but no ping at all when before he did. I made a few changes since a new T1 has been installed. Any who take a quick look at this config...

  ------------------------------

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  ISAKMP crypto key MYKEY address YYY. YYY. YYY. YYY

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac TUNNELSET

  !

  crypto map ipsec-isakmp TUNNEL 1

  defined peer YYY. YYY. YYY. YYY

  game of transformation-TUNNELSET

  match address BIZ - hq

  !

  interface Loopback1

  address IP XXX.XXX. XXX.9 255.255.255.248

  NAT outside IP

  IP virtual-reassembly

  card crypto TUNNEL

  Crypto ipsec df - bit clear

  !

  interface FastEthernet0/0/3

  Description LOCAL_LAN_INTERFACE

  !

  interface Serial0/1/0

  address IP XXX.XXX. XXX.2 255.255.255.252

  NAT outside IP

  IP virtual-reassembly

  encapsulation ppp

  !

  interface Vlan1

  IP 192.168.150.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  !

  IP route 0.0.0.0 0.0.0.0 XXX.XXX. XXX.1

  !

  nat T1 XXX.XXX IP pool. XXX.9 XXX.XXX. XXX.9 netmask 255.255.255.248

  IP nat inside source overload map route sheep pool T1

  !

  DONOTNAT extended IP access list

  deny ip 192.168.150.0 0.0.0.255 192.100.100.0 0.0.0.255

  deny ip 192.168.150.0 0.0.0.255 192.168.1.0 0.0.0.255

  IP 192.168.150.0 allow 0.0.0.255 any

  BIZ - hq extended IP access list

  IP 192.168.150.0 allow 0.0.0.255 192.100.100.0 0.0.0.255

  IP 192.168.150.0 allow 0.0.0.255 192.168.1.0 0.0.0.255

  !

  access-list 20 allow NN. NN.162.160 0.0.0.31

  access-list 20 allow NN. NN.197.192 0.0.0.31

  access-list 20 permit 192.168.150.0 0.0.0.255

  access-list 20 allow 192.168.9.0 0.0.0.255

  !

  sheep allowed 10 route map

  corresponds to the IP DONOTNAT

  You must ensure that the peer set x.x.x.x and isakmp crypto key xxxx address x.x.x.x on the other router point effectively to the new ip address of your router...

  Yes, you can finish on the loopback interface is the command to do this:

  crypto map-name-address-id of interface card

  When you the interface id is your loopback interface...

  For more information on this command, please see the following link:

  http://www.Cisco.com/en/us/products/SW/iosswrel/ps1835/products_command_reference_chapter09186a00800ca7b6.html#wp1018189

  Please rate this message if it helps!

  Kind regards

• Established VPN tunnel between 4.8 Client and 525 PIX but cannot ping

  When there is no tunnel that is established, the client can ping all devices onsite / remote. However when the tunnel is established and the client picks up its expected the address pool IP address, the client can ping or local / remote.

  Debug trace of icmp on the shows of PIX inside devices responding to pings from the client but the client

  does not receive these responses and shows demand exceeded.

  VPN client also shows only the transmitted data.

  I'm guessing that there is a problem of routing/natting somewhere?

  Would really appreciate some help on this? Ask some q If my problem is too vague.

  Thanks in advance!

  Would it be possible to show the hidden config of the PIX with the public IP addresses? Some things to check

  --> ISAKMP Nat traversal

  --> Windows Firewall

  --> syspot allowed

• Customer quick RV042 VPN cannot ping lan network

  Hi guys,.

  I just created a client2gateway on RV042 IPSec tunnel and use the remote PC quick VPN client tries to connect to this router.

  Fast VPN showed that the tunnel has been established. But I couldn't ping the LAN behind the router RV042.

  Can someone help me?

  Thank you.

  Hello

  Yes, you are right. To use the fast with RV042 VPN, it is necessary to configure the user name and a password for access to the VPN Client page. As this router does not support VLANs, you can only connect the VPN client to the LAN subnet (you cannot connect the client to any beach IP configured with multiple subnets)

  Kind regards

  Bismuth

• Client VPN connects but cannot ping all hosts

  Here is the configuration of a PIX 501, which I want to accept connections from the VPN software clients.  I can connect successfully to the PIX using the 5.0.0.7.0290 VPN client and I can ping the PIX to 192.168.5.1, but I can't ping or you connect to all hosts behind the PIX.  Can someone tell me what Miss me in my setup?

  Thanks for your help.

  Chi - pix # sh conf
  : Saved
  : Written by enable_15 at 03:49:39.701 UTC Friday, January 1, 1993
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password
  encrypted passwd
  hostname chi - pix
  .com domain name
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol they 389
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  list-access internet-traffic ip 192.168.5.0 allow 255.255.255.0 any
  Allow Access-list allowed a whole icmp ping
  access-list 101 permit ip 192.168.5.0 255.255.255.0 10.10.11.0 255.255.255.0
  access-list 102 permit ip 192.168.5.0 255.255.255.0 10.10.11.0 255.255.255.0
  pager lines 24
  opening of session
  debug logging in buffered memory
  ICMP deny everything outside
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside pppoe setroute
  IP address inside 192.168.5.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  IP local pool ippool 10.10.11.1 - 10.10.11.254
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) - 0 102 access list
  NAT (inside) 1 list-access internet-traffic 0 0
  group-access allowed to ping in external interface
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp - esp-md5-hmac GvnPix-series
  Crypto-map dynamic dynmap 10 GvnPix-set transform-set
  toGvnPix 10 card crypto ipsec-isakmp dynamic dynmap
  toGvnPix interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address 0.0.0.0 netmask 0.0.0.0
  ISAKMP keepalive 60
  ISAKMP nat-traversal 20
  part of pre authentication ISAKMP policy 9
  encryption of ISAKMP policy 9
  ISAKMP policy 9 md5 hash
  9 2 ISAKMP policy group
  ISAKMP policy 9 life 86400
  vpngroup address ippool pool chiclient
  vpngroup dns 192.168.5.1 Server chiclient
  vpngroup wins 192.168.5.1 chiclient-Server
  vpngroup chiclient com default domain
  vpngroup split tunnel 101 chiclient
  vpngroup idle 1800 chiclient-time
  vpngroup password chiclient *.
  Telnet 0.0.0.0 0.0.0.0 inside
  Telnet timeout 30
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 30
  management-access inside
  Console timeout 0
  VPDN group chi request dialout pppoe
  VPDN group chi net localname
  VPDN group chi ppp authentication pap
  VPDN username password net *.
  dhcpd address 192.168.5.2 - 192.168.5.33 inside
  dhcpd dns xx
  dhcpd rental 86400
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 100
  Cryptochecksum:
  Chi - pix #.

  On the PIX configuration seems correct.

  I guess you try to access hosts in 192.168.5.0/24, and these default hosts is the PIX inside interface 192.168.5.1?

  How you try to access these internal hosts? If you try to ping the hosts, please please make sure there is no personal firewall enabled inside welcomes as personal firewall normally doesn't allow incoming connections from different subnet ip address.

• Cisco ASA 5510 - Cisco Client can connect to the VPN but cannot Ping!

  Hello

  I have an ASA 5510 with the configuration below. I have configure the ASA as vpn server for remote access with cisco vpn client, now my problem is that I can connect but I can not ping.

  Config

  ciscoasa # sh run

  : Saved

  :

  ASA Version 8.0 (3)

  !

  ciscoasa hostname

  activate the 5QB4svsHoIHxXpF password / encrypted

  names of

  xxx.xxx.xxx.xxx SAP_router_IP_on_SAP name

  xxx.xxx.xxx.xxx ISA_Server_second_external_IP name

  xxx.xxx.xxx.xxx name Mail_Server

  xxx.xxx.xxx.xxx IncomingIP name

  xxx.xxx.xxx.xxx SAP name

  xxx.xxx.xxx.xxx Web server name

  xxx.xxx.xxx.xxx cms_eservices_projects_sharepointold name

  isa_server_outside name 192.168.2.2

  !

  interface Ethernet0/0

  nameif outside

  security-level 0

  address IP IncomingIP 255.255.255.248

  !

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 192.168.2.1 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.1.253 255.255.255.0

  management only

  !

  passwd 123

  passive FTP mode

  clock timezone IS 2

  clock summer-time EEDT recurring last Sun Mar 03:00 last Sun Oct 04:00

  TCP_8081 tcp service object-group

  EQ port 8081 object

  DM_INLINE_TCP_1 tcp service object-group

  EQ port 3389 object

  port-object eq ftp

  port-object eq www

  EQ object of the https port

  EQ smtp port object

  EQ Port pop3 object

  port-object eq 3200

  port-object eq 3300

  port-object eq 3600

  port-object eq 3299

  port-object eq 3390

  EQ port 50000 object

  port-object eq 3396

  port-object eq 3397

  port-object eq 3398

  port-object eq imap4

  EQ port 587 object

  port-object eq 993

  port-object eq 8000

  EQ port 8443 object

  port-object eq telnet

  port-object eq 3901

  purpose of group TCP_8081

  EQ port 1433 object

  port-object eq 3391

  port-object eq 3399

  EQ object of port 8080

  EQ port 3128 object

  port-object eq 3900

  port-object eq 3902

  port-object eq 7777

  port-object eq 3392

  port-object eq 3393

  port-object eq 3394

  Equalizer object port 3395

  port-object eq 92

  port-object eq 91

  port-object eq 3206

  port-object eq 8001

  EQ port 8181 object

  object-port 7778 eq

  port-object eq 8180

  port-object 22222 eq

  port-object eq 11001

  port-object eq 11002

  port-object eq 1555

  port-object eq 2223

  port-object eq 2224

  object-group service RDP - tcp

  EQ port 3389 object

  3901 tcp service object-group

  3901 description

  port-object eq 3901

  object-group service tcp 50000

  50000 description

  EQ port 50000 object

  Enable_Transparent_Tunneling_UDP udp service object-group

  port-object eq 4500

  access-list connection to SAP Note inside_access_in

  inside_access_in to access extended list ip 192.168.2.0 allow 255.255.255.0 host SAP_router_IP_on_SAP

  access-list inside_access_in note outgoing VPN - PPTP

  inside_access_in list extended access permitted tcp 192.168.2.0 255.255.255.0 any eq pptp

  access-list inside_access_in note outgoing VPN - GRE

  inside_access_in list extended access allow accord 192.168.2.0 255.255.255.0 any

  Comment from inside_access_in-list of access VPN - GRE

  inside_access_in list extended access will permit a full

  access-list inside_access_in note outgoing VPN - Client IKE

  inside_access_in list extended access permitted udp 192.168.2.0 255.255.255.0 any isakmp eq

  Comment of access outgoing VPN - IPSecNAT - inside_access_in-list T

  inside_access_in list extended access permitted udp 192.168.2.0 255.255.255.0 any eq 4500

  Note to inside_access_in of outgoing DNS list access

  inside_access_in list extended access udp allowed any any eq field

  Note to inside_access_in of outgoing DNS list access

  inside_access_in list extended access permit tcp any any eq field

  Note to inside_access_in to access list carried forward Ports

  inside_access_in list extended access permitted tcp 192.168.2.0 255.255.255.0 any DM_INLINE_TCP_1 object-group

  access extensive list ip 172.16.1.0 inside_access_in allow 255.255.255.0 any

  outside_access_in of access allowed any ip an extended list

  outside_access_in list extended access permit tcp any any eq pptp

  outside_access_in list extended access will permit a full

  outside_access_in list extended access allowed grateful if any host Mail_Server

  outside_access_in list extended access permit tcp any host Mail_Server eq pptp

  outside_access_in list extended access allow esp a whole

  outside_access_in ah allowed extended access list a whole

  outside_access_in list extended access udp allowed any any eq isakmp

  outside_access_in list of permitted udp access all all Enable_Transparent_Tunneling_UDP object-group

  list of access allowed standard VPN 192.168.2.0 255.255.255.0

  corp_vpn to access extended list ip 192.168.2.0 allow 255.255.255.0 172.16.1.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Outside 1500 MTU

  Within 1500 MTU

  management of MTU 1500

  pool POOL 172.16.1.10 - 172.16.1.20 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 603.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Global (outside) 2 Mail_Server netmask 255.0.0.0

  Global 1 interface (outside)

  Global interface (2 inside)

  NAT (inside) 0-list of access corp_vpn

  NAT (inside) 1 0.0.0.0 0.0.0.0

  static (inside, outside) tcp Mail_Server 8001 8001 ISA_Server_second_external_IP netmask 255.255.255.255

  static (inside, outside) tcp Mail_Server 8000 ISA_Server_second_external_IP 8000 netmask 255.255.255.255

  static (inside, outside) tcp Mail_Server pptp pptp netmask 255.255.255.255 isa_server_outside

  public static tcp (indoor, outdoor) Mail_Server smtp smtp isa_server_outside mask 255.255.255.255 subnet

  static (inside, outside) tcp 587 Mail_Server isa_server_outside 587 netmask 255.255.255.255

  static (inside, outside) tcp Mail_Server 9444 isa_server_outside 9444 netmask 255.255.255.255

  static (inside, outside) tcp 9443 Mail_Server 9443 netmask 255.255.255.255 isa_server_outside

  static (inside, outside) tcp 3389 3389 netmask 255.255.255.255 isa_server_outside Mail_Server

  static (inside, outside) tcp 3390 Mail_Server 3390 netmask 255.255.255.255 isa_server_outside

  static (inside, outside) tcp Mail_Server 3901 isa_server_outside 3901 netmask 255.255.255.255

  static (inside, outside) tcp SAP 50000 50000 netmask 255.255.255.255 isa_server_outside

  static (inside, outside) tcp SAP 3200 3200 netmask 255.255.255.255 isa_server_outside

  static (inside, outside) SAP 3299 isa_server_outside 3299 netmask 255.255.255.255 tcp

  static (inside, outside) tcp Mail_Server www isa_server_outside www netmask 255.255.255.255

  static (inside, outside) tcp Mail_Server https isa_server_outside https netmask 255.255.255.255

  static (inside, outside) tcp Mail_Server pop3 pop3 netmask 255.255.255.255 isa_server_outside

  static (inside, outside) tcp imap4 Mail_Server imap4 netmask 255.255.255.255 isa_server_outside

  static (inside, outside) tcp cms_eservices_projects_sharepointold 9999 9999 netmask 255.255.255.255 isa_server_outside

  public static 192.168.2.0 (inside, outside) - corp_vpn access list

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.2.0 255.255.255.0 inside

  http 192.168.1.0 255.255.255.0 management

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp - esp-md5-hmac transet

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 transform-set ESP-3DES-SHA transet

  cryptomap 10 card crypto ipsec-isakmp dynamic dynmap

  cryptomap interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  Telnet 192.168.2.0 255.255.255.0 inside

  Telnet 192.168.1.0 255.255.255.0 management

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx interface inside

  dhcpd domain.local domain inside interface

  !

  a basic threat threat detection

  host of statistical threat detection

  Statistics-list of access threat detection

  Management Server TFTP 192.168.1.123.

  internal group mypolicy strategy

  mypolicy group policy attributes

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value VPN

  Pseudo vpdn password 123

  vpdn username attributes

  VPN-group-policy mypolicy

  type of remote access service

  type mypolicy tunnel-group remote access

  tunnel-group mypolicy General attributes

  address-pool

  strategy-group-by default mypolicy

  tunnel-group mypolicy ipsec-attributes

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the pptp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:b8bb19b6cb05cfa9ee125ad7bc5444ac

  : end

  Thank you very much.

  Hello

  You probably need

  Policy-map global_policy

  class inspection_default

  inspect the icmp

  inspect the icmp error

  Your Tunnel of Split and NAT0 configurations seem to.

  -Jouni