vShield edge # configure terminal

Similar Questions

• VShield Edge Configuration

  Hello

  I recently installed vshield Edge:

  There are two device that have been added to the inventory...

  I set up an internal IP address as my private subnet AND an uplink to have a public IP... and I configured the default Gateway to match my public by default Gateway...

  now I have a machine virtual on my private network that I change the gateway is the IP address assigned to the internal interface of vshield Edge... But it is still not Internet ping!

  Am I missing or wrong configured something?

  Help, please

  Thank you

  Hello

  The reason for two devices could be that you may have installed Edge in HA mode.

  Coming to your network problem, check the following.

  • Check if you have applied the SNAT rule on the external network. In this, the initial INVESTIGATION period should be your private IP network and the translated IP must be one (or) range of your public IP addresses. You must allocate under the IP translated before using NAT.
  • Check if the firewall is disabled (or) added with one exception.

• vShield Networking - configure NAT rules directly in vShield Mnager

  Hello

  I tried to configure a NAT rule to enable access for external network users that is not routable vsphere Client i.e. the plugin for vShield manager to the internal network. I have found no documentation for this. Now, if I place a load balancer it automatically creates a NAT rule. Don't know why I can't do the same thing using NAT exclusively. Someone out there who has done the basic NAT using vShield Edge between 2 distinct networks (L2)?

  I realized what was wrint with my setup. The EDGE is deployed in a lab where we have the internal network, access to the outside, but not the reverse. Thus, we had another gateway on the virtual machine and therefore return traffic never returned to the edge gateway. If it was a problem with my knowledge of NAT.

  Next article helpde much:

  http://kickingwaterbottles.WordPress.com/2013/08/12/hairpin-NAT-NAT-Hairpinning-with-VShield-edge/

  Thank you

  Mohit Kshirsagar

• vShield Edge balancer to load within vCloud Director?

  Hi all

  I had a long week, installation and configuration vCloud Director. So far, it looks great.

  However, I wanted to create a paralytic with 2 web servers and a LoadBalancer (vShield Edge device) in front of them. I just don't seem to be able to find anything about how I activate on the web site of vCloud Director. I can do the NAT and firewall, but balancing is missing ... I'm sure it's there somewhere, I'm just not see it!

  Can someone point me to the right direction?

  Bgrds,

  Finnzi

  This requires the additional license for vShield edge and configure vShield to vCenter PLugin.  There is no user interface in vCD interface to configure the load balaning VSE again.  1.5 introduces the possibility to configure VPN (if authorized), through vCD, but not the LB function again.

• Advancing the Straight Edge configuration in the Vision Assistant

  Hello world

  I used the function advance Straight Edge with Vision Assistant who I little understand but this is not enough for what I'm trying to achieve. I tried to find some info on the underlying theory, but the only thing I found is the help document for it, which provides details on the different variables only.

  Could you please tell me where I could find a good source of information on edge configurations right ahead?

  Thank you  

  Take a look at the NIVisionConcepts.chm you could find under ...\National Instruments\Vision\Documentation.

  

  Christian

• Trying to block "configures terminal" on GBA 5.3

  Hi friends!

  I'm trying to block users to use the command "Configure Terminal Server" using GBA 5.3, but so far it is working properly.

  The same set of orders, if I put any other command (such as reload, telnet) and choose to refuse, it works very well, but to prevent the user to enter in Setup mode, I'm not able to block again.

  I really appreciate if someone here can help me or if she has already passed for this situation.

  Thank you!

  MOV

  On GBA, please use "Deny set up" and do not fill the field argument. Remove the other sets of similar orders.

  On the side of the IOS, make sure you have

  aaa authorization config-commands

• No command ' configure terminal ' privilege mode

  Hi guys,.

  I'm seting up a 1250G AP Cisco via port console for the first time, something very strange, I can not find command "configure terminal" under privileged mode. Does anyone know why? Thanks in advance.

  AP0026.994C.e39c #sh privilege
  Current privilege level is 15
  AP0026.994C.e39c #?
  Exec commands:
  CD change current directory
  Disable the Reset functions
  Manage the clock system clock
  Crypto encryption related orders.
  debug debugging features (see also "undebug")
  Delete Deletes a file
  List of files on a file system dir
  disable the Turn off privileged commands
  dot1x IEEE 802. 1 X commands Exec
  turn on the turn on privileged commands
  exit from the EXEC
  fsck Fsck a file system
  help Description of the interactive help system
  led functions LED
  locking of the terminal
  Connection connect you as a particular user
  Logout Exit from the EXEC
  OfficeExtend AP lwapconfig configurations
  LWAPP lwapp exec commands
  mkdir create new directory
  monitor various system events monitoring
  more display the contents of a file
  Name the connection-name an existing network connection
  No function to disable debugging
  Send echo ping messages
  Working Directory current pwd display
  RADIUS radius exec orders
  Release to release a resource
  Stop reload and perform a restart cold
  Rename rename a file
  renew renew a resource
  rmdir remove the existing directory
  rsh to execute a remote command
  Register early to save the battery raise_interrupt_level
  Send a message to other TTY lines
  setting system Set Set (no config)
  Show Show running system information
  SSH open a secure shell client connection
  SYSTAT display information about the terminal lines
  terminal Set terminal line parameters
  Test Test subsystems, memory and interfaces
  Traceroute-Trace route to destination
  undebug disable debugging functions (see also 'debug')
  software upgrade upgrade
  Check check a file
  where the list of active connections

  AP0026.994C.e39c ter #config
  ^
  Invalid entry % detected at ' ^' marker.

  AP0026.994C.e39c #.

  AP0026.994C.e39c #sh worm
  Software Cisco IOS, C1250 Software (C1250-K9W8-M), Version 12.4 JA (21 a), RELEASE SOFTWARE (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2009 by Cisco Systems, Inc.
  Updated Tuesday 8 June 09 16:49 by prod_rel_team

  Hello

  The reason why you do not have the config t prompt is because you have a LWAPP access point. LWAPP ap do not have a config t, as the access point's configuration of the WLC.

  If you find the useful rate please post... Thank you!

• SSH on vShield Edge using Java CCES

  I am trying to connect to vShield Edge using jsch for SSH connection library.

  Connection to a linux server it works perfectly, but connected to the vShield edge server, the output is:

  vtysh: invalid option-'c '.

  Try "vtysh - help ' for more information.

  What it means?

  The connection seems to work correctly, I think the problem is the command I want exec ('list' command).

  I tried many commands, but I always have the same answer.

  I also used this methos Java to set the Pty:

  (Channel) .setPtyType ("vt100") (ChannelExec);

  Can I define another type?

  Thank you all

  Giovanni

  I was determined to uisng the ssh-tool Java library

  You can retrieve the lib since this link sourceForge: SSHTools | Free software on SourceForge.net downloads

  And here is my code.

  Was indeed a problem of reading of the result of the command, but it should be simple to solve.

  public {} public static void executeSSHCommand (String username, String password, String hostname, string command)

  SshClient ssh = new SshClient();

  PasswordAuthenticationClient auth = new PasswordAuthenticationClient();

  int result = 0;

  Session SessionChannelClient = null;

  OutputStream out = null;

  BufferedReader in = null;

  try {}

  SSH. Connect (hostname, new IgnoreHostKeyVerification());

  auth.setUsername (username);

  auth.setPassword (password);

  result = ssh.authenticate (auth);

  If (result! = AuthenticationProtocolState.COMPLETE) {}

  System.out.println ("authentication error");

  }

  session = ssh.openSessionChannel ();

  session.startShell ();

  out = session.getOutputStream ();

  out. Write (Command.GetBytes ());

  in = new BufferedReader (new InputStreamReader (session.getInputStream ()));

  Read string = null;

  While ((read = in.readLine ())! = null) {}

  System.out.println (Read);

  }

  } catch (IOException ex) {}

  }

  }

  Hope this helps others :-)

• VShield edge Nic

  Hello world

  I installed VSphere 5.5, 5.5 VCloud and VShield 5.5 for a test. Everything seems fine. But when I create an organization VDC and add an EDGE gateway for him, the automatic system create a VM VSE under "system vDC". Virtual machine contains multiply network cards, including two he uses for the external network and the Organization's network. But there are still many that connect to a standard switch named 'None '.

  Although it works well, the problem is I can not migrate or do his host in maintenance mode. During the migration network interface adapter, it shows"2 use 'none' network, which is not accessible. »

  Does anyone know something?

  Thank you

  This should be a non-issue.

  Each vShield edge device has 10 NIC cards.  One will be attached to a given network (an external, one internal).

  The 'None' network, a group of port assigned.  This does not block vMotion does not happen, and I was

  Even if you get one! ------warning message, you should still be able to click Next and complete the vMotion.

  The only way you would be blocked from vMotion is if one of the two real networks were somehow connected to a specific host.

  Can you provide a screenshot of it with the next button grey and everything that is not a warning to the network no?

• Problem assigning vShield edge licenses

  We have a cluster running vCenter 5.1 standard with 3 hosts ESXi 4.1 under license with vSphere 4 Enterprise Plus keys. Recently, I've deployed a vCloud Director 5.1 with a Manager Server 5.1.2 Server vShield. I was able to successfully add the vCenter vCloud and vShield Manager. Then when I try to add our license of vShield edge in vCenter as the installation guide document, I can't find the CIS or POSSIBLE asset in vCenter section "permit". Is it because we lack of vSphere 4 license?

  

  The problem is now resolved. Recently, we are improving our vCenter 4.1 to 5.1. The appliance Manager vShield was installed before the upgrade. After the upgrade, I didn't perform a reboot of the vCenter server. Once I restarted the server vCenter, he was able to found the vShield active Edge of the appliance Manager vShield.

• About the origin/Edge configuration

  Hello, I'm quite new to Adobe Flash Media Server and have been reading administration guide.

  After reading the information of origin/edge here:

  leader = 00000130.html & http://livedocs.adobe.com/fms/2/docs/wwhelp/wwhimpl/common/html/wwhelp.htm?context=LiveDoc s_Parts

  I came across a few questions.

  1. it is said that edge server essentially act as a "proxy" gets all inbound connections, which redirects them to the originating server.

  But I read here:

  leader = 00000130.html & http://livedocs.adobe.com/fms/2/docs/wwhelp/wwhimpl/common/html/wwhelp.htm?context=LiveDoc s_Parts

  that basically just edge transport server uses 1 connection initially and ordered that all users who connect. I am an old user of shoutcast/icecast, and this terminology is a little different. Origin/Edge configuration is basically correct relay? An edge transport server relays a stream from the origin server, and ordered everyone still correct?

  So I might have a relatively low origin server and low bandwidth and have 3 edge server to connect to the origin and have about 100 users to connect to each server 3 edge?

  2. This is the question that that concern me the most. Currently I have swf and HTML field restriction to my application on the original server. If I set up an edge transport server it will respect safety (html and swf domain restrictions) set to the correct home server? Or should I re-enter the areas these 2 files on the edge transport server?

  3. when I completely setup my origin/edge servers, will still be able to connect to the origin? Or they will have access on board?

  4. is there a way to limit the number of users connected to a server and after that it caps out, every future connection is then sent to another edge transport server?

  We hope to hear for you guys.

  Thank you!

  It is not that we do not know, is that we have not gotten here yet.

  1. edge/origin does many things.  It is a complete solution or a simple approximation.  Edge tries to take as much load to the server of origin as possible, therefore he handles VOD delivery locally if the media is cached, distributes broadcasts by pulling only once, but redisting, and it multiplexes all incoming connections on the edge more than one (actually two, but that's a minor detail) to the origin by the remote application conveyed. Origin must manage all scripts, is the authority on the content and registration or the Summit meeting point in direct topologies.  If you have a low origin?  Probably not because he is will again fill media content, especially at the beginning, when the caches are empty, constly.  If you run the script, happens to process the script for all customers, including those on the edges, so that can be costly - should be a great machine?  probably not - when caches work correctly, you should see limited on the origin, etc. support.

  2 edge transport server has its own independent area restrictions.  They are not provided to original aboard.  Allows you to create an origin configuration where it accepts that the edges or other machines in your domain and you can target other areas by the edge transport server.  So, if you want them all in honor of these settings, you'll want to change it on all configurations.

  3. an origin server can always handle direct traffic with or without subscription the edges.  I'll make sure that you are up-to-date with the latest version of FMS, especially 3.5.3 when it comes out that we have fixed some bugs in our DVR implementation in this area.  Nothing catastrophic, just want to ensure that you have the version that works best and we are considered correction of problems loading strongly edge based both local basic traffic (especially in a network of 3 level or more, but you're not here)

  4. you can write like this logic in an access adapter - actually it is exactly what it is designed for.  There the number of connections - for the server and the command of redirection at your disposal so write some logic there please.

  ASA

• Addition of vShield Edge NAT rules from a CSV using PowerCLI

  I recently read Alan great post on adding NAT here rules: http://www.virtu-al.net/2014/07/24/working-vcd-edge-gateway-rules-powercli/

  I used it successfully for simple rules in a lab environment, but hundreds of rules I need to do in Production.

  Although I managed to hack together an Excel spreadsheet that concatenated all these parameters to create each order, I was wondering if there was a faster way to do it.

  My plan was to modify the script to Alan to import a CSV file, and then loop through each line and generate the XML file in a single pass.

  However, I am very rusty on my scripting skills, so I thought I would first ask if this has already been done by someone else.

  Anyone know if there is a way to update the rules of NAT edge vShield from a CSV file?

  Adam,

  I was an associate of the original request for this feature. Alan made us most of the way with a function to create a single rule, but as in your use case, we also had a lot of rules to build everything at once.

  Our solution was rather minor tweaks and the creation of 3 functions rather than 2.

  * Feature: New DNATRuleXML and new SNATRuleXML.  We have created these two functions to build the string XML (one for the SNAT) and one for the DNAT, their results are stored in a global variable.

  * Function: New-NATXMLExecute. It is a function execute to execute the creation of the great XML string created in the above functions.

  You should change/use power rule XML functions to interface with one worksheet, and then you should be far away. It will be useful.

  Example of code is below:

  ===============================================

  Function (new-NATXMLExecute

  $EdgeGateway,

  $NATXML,

  $FirewallEnable) {}

  Write-Host "' no nExecuting add it NAT function"-ForegroundColor Cyan

  Write-Host "-----------------------------------------------------"

  Write-Host "EdgeGateway: 't' t$ EdgeGateway '.

  #Write - Host "' tNATXML: 't' t$ NATXML '.

  Write-Host "activate the firewall?: 't' t$ FirewallEnable '.

  Write-Host "-----------------------------------------------------"

  $Edgeview = search clouds QueryType - EdgeGateway-name $EdgeGateway | Get-CIView

  If (! $Edgeview) {}

  Write-Warning 'edge Gateway with $Edgeview name not found. "

  Output

  }

  $URI = ($edgeview. Href + ' / action/configureServices ")

  $wc = new-Object System.Net.WebClient

  # Add Authorization headers

  $wc. Headers.Add ("x-vcloud-authorization", $Edgeview.Client.SessionKey)

  $wc. Headers.Add ("Content-Type", "application/vnd.vmware.admin.edgeGatewayServiceConfiguration+xml")

  $wc. Headers.Add ("Accept", "application / * + xml;") version = 5.1 ")

  $webclient = New-Object system.net.webclient

  $webclient. Headers.Add("x-vcloud-authorization",$Edgeview.Client.SessionKey)

  $webclient. Headers.Add ("accept", $EdgeView.Type + ";") version = 5.1 ")

  [xml] $EGWConfXML is $webclient. DownloadString($EdgeView.href)

  [xml] $OriginalXML = $EGWConfXML.EdgeGateway.Configuration.EdgegatewayServiceConfiguration.NatService.outerxml

  #Check if the firewall is turned on

  $FirewallStatus = $EGWConfXML.EdgeGateway.Configuration.EdgegatewayServiceConfiguration.FirewallService.IsEnabled

  Write-Host "active current firewall status: $FirewallStatus.» "This will be changed to: $FirewallEnable.

  LogWrite "active current firewall status: $FirewallStatus.» "This will be changed to: $FirewallEnable.

  If (($NATXML) - or ($FirewallStatus - not $FirewallEnable)) {}

  $GoXML = '

  http://www.VMware.com/vCloud/v1.5">

  "' + $FirewallEnable +"

  drop

  fake

  true'

  $OriginalXML.NatService.NatRule | {Foreach}

  $GoXML += $_. OuterXML

  }

  $GoXML += $NATXML

  $GoXML += '

  '

  $script: NATXMLExecute = $GoXML

  [byte []] $byteArray = [System.Text.Encoding]: ASCII. GetBytes ($GoXML)

  $UploadData = $wc. UploadData ("POST", $URI, $bytearray)

  $EdGWStatus = EdgeGatewayStatus - EdgeGateway $EdgeGateway

  Write-Host - NoNewline "Waiting for EdgeGateway configure...". »

  LogWrite "Waiting for EdgeGateway configure...". »

  While ($EdGWStatus - no "ready")

  {

  Start-Sleep - seconds 3

  Write-Host - NoNewline ". »

  $EdGWStatus = EdgeGatewayStatus - EdgeGateway $EdgeGateway

  If ($EdGWStatus - eq "Error") {}

  Write-Host "Error Has occurred...". Check the EdgeGateway"- ForegroundColor Red

  LogWrite "Error Has occurred...". Check the EdgeGateway.

  breaking

  }

  }

  Write-Host - NoNewline ".» EdgeGateway Ready.

  Write-Host "' nNAT complete building.»  ForegroundColor - Green

  LogWrite "NAT complete building."

  }

  else {}

  Write-Host "no change necessary." No changes have been made to the EdgeGateway"- ForegroundColor yellow

  LogWrite "no modification required...". No change was made.

  }

  }

  Function (new-DNATRuleXML

  $EdgeGateway,

  $ExternalNetwork,

  $OriginalIP,

  $OriginalPort,

  $TranslatedIP,

  $TranslatedPort,

  $Protocol) {}

  Write-Host "Building DNAT rule XML" - ForegroundColor yellow

  Write-Host "' tEdgeGateway: 't' t$ EdgeGateway '.

  Write-Host "' tExternalNetwork: ' t$ ExternalNetwork '.

  Write-Host "' tOriginal IP: 't' t$ OriginalIP '.

  Write-Host "' tOriginalPort: 't' t$ OriginalPort '.

  Write-Host "' tTranslatedIP: 't' t$ TranslatedIP '.

  Write-Host "' tTranslatedPort: 't' t$ TranslatedPort '.

  Write-Host "' tProtocol: 't' t$ Protocol.

  $Edgeview = search clouds QueryType - EdgeGateway-name $EdgeGateway | Get-CIView

  If (! $Edgeview) {}

  Write-Warning 'edge Gateway with $Edgeview name not found. "

  Output

  }

  $URI = ($edgeview. Href + ' / action/configureServices ")

  $wc = new-Object System.Net.WebClient

  # Add Authorization headers

  $wc. Headers.Add ("x-vcloud-authorization", $Edgeview.Client.SessionKey)

  $wc. Headers.Add ("Content-Type", "application/vnd.vmware.admin.edgeGatewayServiceConfiguration+xml")

  $wc. Headers.Add ("Accept", "application / * + xml;") version = 5.1 ")

  $webclient = New-Object system.net.webclient

  $webclient. Headers.Add("x-vcloud-authorization",$Edgeview.Client.SessionKey)

  $webclient. Headers.Add ("accept", $EdgeView.Type + ";") version = 5.1 ")

  [xml] $EGWConfXML is $webclient. DownloadString($EdgeView.href)

  [xml] $OriginalXML = $EGWConfXML.EdgeGateway.Configuration.EdgegatewayServiceConfiguration.NatService.outerxml

  If {($Script:NewID)}

  $Script: NewID += 1

  $NewID = $Script: NewID

  }

  else {}

  $NewID = [int]($OriginalXML.NatService.natrule |) Sort identifier. (Select the Id - Last 1) user.user + 1

  If {($NewID-éq. 1)}

  #If NoID was found, set the correct ID of departure

  $NewID = 65537

  }

  $Script: NewID = $NewID

  }

  $strXML = '

  DNAT

  true

  ' + $NewID + '

  "' + $OriginalIP +"

  "' + $OriginalPort +"

  "' + $TranslatedIP +"

  "' + $TranslatedPort +"

  ' + $Protocol + '

  '

  $script: DNATXML = $StrXML

  }

  Function (new-SNATRuleXML

  $EdgeGateway,

  $ExternalNetwork,

  $OriginalIP,

  $TranslatedIP

  ) {

  Write-Host "Building SNAT rule XML" - ForegroundColor yellow

  Write-Host "' tEdgeGateway: 't' t$ EdgeGateway '.

  Write-Host "' tExternalNetwork: ' t$ ExternalNetwork '.

  Write-Host "' tOriginal IP: 't' t$ OriginalIP '.

  Write-Host "' tTranslatedIP: 't' t$ TranslatedIP '.

  $Edgeview = search clouds QueryType - EdgeGateway-name $EdgeGateway | Get-CIView

  If (! $Edgeview) {}

  Write-Warning 'edge Gateway with $Edgeview name not found. "

  Output

  }

  $URI = ($edgeview. Href + ' / action/configureServices ")

  $wc = new-Object System.Net.WebClient

  # Add Authorization headers

  $wc. Headers.Add ("x-vcloud-authorization", $Edgeview.Client.SessionKey)

  $wc. Headers.Add ("Content-Type", "application/vnd.vmware.admin.edgeGatewayServiceConfiguration+xml")

  $wc. Headers.Add ("Accept", "application / * + xml;") version = 5.1 ")

  $webclient = New-Object system.net.webclient

  $webclient. Headers.Add("x-vcloud-authorization",$Edgeview.Client.SessionKey)

  $webclient. Headers.Add ("accept", $EdgeView.Type + ";") version = 5.1 ")

  [xml] $EGWConfXML is $webclient. DownloadString($EdgeView.href)

  [xml] $OriginalXML = $EGWConfXML.EdgeGateway.Configuration.EdgegatewayServiceConfiguration.NatService.outerxml

  If {($Script:NewID)}

  $Script: NewID += 1

  $NewID = $Script: NewID

  }

  else {}

  $NewID = [int]($OriginalXML.NatService.natrule |) Sort identifier. (Select the Id - Last 1) user.user + 1

  If {($NewID-éq. 1)}

  #If NoID was found, set the correct ID of departure

  $NewID = 65537

  }

  $Script: NewID = $NewID

  }

  $strXML = '

  SNAT

  true

  ' + $NewID + '

  "' + $OriginalIP +"

  "' + $TranslatedIP +"

  '

  $script: SNATXML = $StrXML

  }

  ===============================================

• Cisco 1142 - configure Terminal disappeared?

  Team,

  I have a Cisco AP 1142 that I am using, the question that I have met, it's that I don't have the possibility of entering the terminal configuration mode. I am really confused as to why I can't access the Terminal configuration (conf t) to the AP. I'm working on a large number of AP, but it seemed to lift my curiosity as to why?

  I posted the info version as well as help (?) menu structure. Any help is greatly appreciated.

  -------------------------------------------------------------------------------------------

  AP003a.99eb.7e63 #SH worm
  Cisco IOS Software, C1140 (C1140-K9W8-M), Version 15.2 (2) JA1, RELEASE SOFTWARE (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2013 by Cisco Systems, Inc.
  Updated Thursday, January 23, 13 12:13 by prod_rel_team

  ROM: Bootstrap program is C1140 boot loader
  BOOTLDR: C1140 program boot (BOOT-C1140-M), Version 12.4 (23 c) JA, VERSION of the SOFTWARE (fc3)

  AP003a.99eb.7e63 operating time is 5 minutes
  System return to the ROM to reload
  System image file is "flash:/c1140-k9w8-mx.152-2.JA1/c1140-k9w8-mx.152-2.JA1".
  Last reason for reloading:

  This product contains cryptographic features and is under the United States
  States and local laws governing the import, export, transfer and
  use. Delivery of Cisco cryptographic products does not imply
  third party approval to import, export, distribute or use encryption.
  Importers, exporters, distributors and users are responsible for
  compliance with U.S. laws and local countries. By using this product you
  agree to comply with the regulations and laws in force. If you are unable
  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:
  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at
  [email protected] / * /.

  Cisco AIR-LAP1142N-A-K9 (PowerPC405ex) Prozesseur (revision A0) 81910K / 49152K bytes of memory.
  Card processor ID FTX1528K5S5
  PowerPC405ex CPU at 586 Mhz, the 0x147E revision number
  Last reset of reloading
  Image LWAPP 7.3.112.0 version
  1 gigabit Ethernet interface
  2 802.11 radios

  32K bytes memory simulated by flash not volatile configuration.
  Basic Ethernet MAC address: 00: 3A: 99:EB:7E:63
  Part number: 73-12836-02
  Kit numbered PCA: 800-33767-02
  Revision number of PCA: A0
  Serial number of PCB: FOC15254JU1
  Top Assembly part number: 800-33775-01
  Top of page the Assembly serial number: FTX1528K5S5
  Top of page revision number: A0
  Product/model number: AIR-LAP1142N-A-K9

  Configuration register is 0xF

  You have light AP requiring WLC to manage.

  You need to convert offline if you want to use as Standalone AP

  http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

  HTH

  Rasika

  Pls note all useful responses *.

• vShield Edge DHCP Options

  Hi guys,.

  I play a vCHS TPOC. I was wondering if it was possible to set any other advanced DHCP option on the edge of vshield like WINS etc?

  As far as I can see there is not, but thought I would ask.

  Concerning

  D

  It is not possible today.

  Is WIN what you are looking for? Or other options as well?

  Thank you.

• Error creating vShield Edge Device for Org vDC

  I'll put up a cloud of assessment, according to the vCloud Director 5.1 evaluation Guide.  I hit a snag as he tried to set up the edgeGateway for my org vDC.

  Here is the error:

  Deployment of edge gateway coke_edge_gateway has failed.

  org.springframework.web.client.ResourceAccessException: i/o error: no route to host. nested exception is java.net.NoRouteToHostException: no route to host

  I don't know even what a host that makes reference.

  'host' is the vShield Manager, which had become inaccessible because of my clumsiness