vSphere 5.0 and 5.5 SSO design question

Similar Questions

• with vSphere and Dell MD3000i iSCSI design

  I installed a server ESX 4 (the first of three for this cluster), and a SAN Dell MD3000i iSCSI connected through two switches Dell PowerConnect 2816.

  Now I read the VMware 'iSCSI SAN configuration guide', and I wanted to just make sure I did the design correcly.

  I have connected a Teddy ESX (vmnic1) to one of the pSwitch and another (vmnic5) in the second. This pSwitch SAN iSCSI ports are connected, so that one of the switches carry the 10.10.10.x subnet and the other the 10.10.11.x (see IP plan below)

  The two natachasery have a vSwitch each (a do not share), a portgroup each and are configured on different subnets, IP (see attached screenshot)

  Plan of intellectual property:

  Port iSCSI-10 group (VMkernel): 10.10.10.1

  Port group iSCSI-11 (VMkernel): 10.10.11.1

  0-0 SAN controller: 10.10.10.10

  SAN 0-1 controller: 10.10.11.10

  Controller 1-0 San: 10.10.10.11

  SAN 1-1 controller: 10.10.11.11

  By using this configuration, I could see four different paths for each LUN. and I was able to make the ESX Server will switch to different switches/controllers as I unplug the vmnic1 network cables and vmnic5, one at a time.

  Then I found the section on 'esxcli' configuration guide and multipathing configuration, which I carried out in accordance with the instructions ("esxcli swiscsi nic add - n vmk0 d vmhba34" and "esxcli swiscsi nic add - n vmk1 vmhba34 d ')

  Now I have eight different paths for each logic unit number, three of whom are 'Active' and an 'active (i/o)' (see my screen attached the capture).

  So, my questions are:

  1. the eight paths to each LUN really normal in designs of iSCSI?

  2. is my vSwitch/Teddy/pSwitch correct design choices?

  Thanks in advance!

  / Anders

  @hennish,

  As long as your new design continues to meet your needs of failover and workload, your infrastructure design should be fine.

  But you might want to take a look at this design Dell. In particular, step 12 that configures multiple paths in round-robin policy using the VI GUI client, for

  Each LUN exposed to the ESX Server. This allows balancing on two

  Active paths to the LUN. After completing this step, you should see2 "IO Active" paths.

  Kind regards

  KongY@Dell Inc.

• I can switch between the code sheet and css html, but I would like to see them both at the same time as well as the design window. Right now and can see rather the design and code html or design and css. How can I arrange to see all at the same time, of

  Hello

  My name is Ellie and I am new to Dreamweaver.

  I can switch between the code sheet and css html, but I would like to see them both at the same time as well as the design window. Right now and can see rather the design and code html or design and css. How can I arrange to see everything at the same time, design, HTML and CSS?

  Thank you

  It ends up something like that...

  

• I have a MAC - 10.11.3 and I downloaded CS6 Design & Web, but cannot be installed

  I have a MAC 10.11.3 and I downloaded CS6 Design & Web but cannot install it.  An error came and said: ' we encountered the following problems ~ setup initialization failed. "  Please download Adobe Support Advisor to detect the problem. "So I clicked on the link and it says that Adobe Support Advisor is no longer available.  I'm not very computer savy and don't know what to do.  Help, please!  Thank you!

  start at the top and work your way down to apply applicable patches until your problem is solved.

  If (win) cc: https://helpx.adobe.com/creative-cloud/kb/creative-cloud-desktop-application-failed.html

  If your error is:

  "Setup failed to initialize. File not found. ' or 'could not initialize installation. This could be due to missing files.

  first of all, rename folder OOBE OOBE.old.

  to find the OOBE:

  Win 64 bit OS: Program Files x86\Common Files\Adobe\OOBE

  Win 32 bit OS: Program Files \Common Files\Adobe\OOBE

  Mac os: HD > library > application support of > adobe > caps

  Mac os: USER > library > application support of > adobe > OOB

  If it fails or isn't the exact error you see, uninstall, clean (http://www.adobe.com/support/contact/cscleanertool.html) and reinstall.

  If you use an installation dvd:

  Copy the contents of the drive in a desktop folder and install from this directory.

  If you are using a mac:

  1. try to create a new user account in Mac with administrator privileges.

  2. connect to the new user, navigate to Mac HD > Application > utilities > Adobe Installer folder, locate products such as Adobe Reader, Adobe Flash, Adobe Air and uninstall the

  3. navigate to the user library > Application Support > Adobe and Adobe put in the trash.

  4. navigate to Mac HD > library > Application Support > Adobe and Adobe put in the trash.

  5 restart the installation.

  If everything is applicable above fails, check your Setup logs:

  http://helpx.Adobe.com/Photoshop-elements/KB/troubleshoot-install-using-logs-elements.html

• The path 'Administrator@VSPHERE.LOCAL.log' and 'noUser.log' in VCENTER 6.0

  Hi all

  I have deployed the plugin in vcenter 6.0 and it is deployed successfully.

  I found the diary of the Virgin in C:\ProgramData\VMware\vCenterServer\logs\vsphere-client\logs.

  But I could not find "[email protected]" and "noUser.log" where my plugin will record all the problems.

  Kindly help me.

  As far as I KNOW vsphere_client_virgo.log contains everything.  Check out server/configuration/serviceability.xml where you can reactivate user logs.

• vSphere 5.0 and 5.5 ESXi cluster

  Hello

  We intend to improve vsphere 5.0 and 5.5 in 2015.  We are truly in a process of buying new servers and I would like to know if I can get the two 5.0 and 5.5 to ESXi ESXi in the same cluster.  If it is possible I vMotion virtual machines in 5.0 for servers 5.5 ESXi ESXi servers and get the ESXi 5.0 on the cluster.

  Thank you.

  Yes, you will first get vCenter to 5.5 and you cannot upgrade the hardware virtual past version 9 until all hosts have been upgraded.  In addition, you cannot move data warehouses to VMFS5 until all hosts have been upgraded.

  I hope this helps...

• Please mention even small and large difference in features vSphere 5.1 and 5.5 of vSphere.

  Friends,

  Please mention even small and large difference in features vSphere 5.1 and 5.5 of vSphere.

  His advantage and advantage tell.

  Concerning

  Sirot

  I would recommend you read http://www.vmware.com/files/pdf/vsphere/VMware-vSphere-Platform-Whats-New.pdf to find out what is new, and that these features are important to you.

  André

• This VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure

  ESXI 4.0 3 running virtual machines.

  600 GB HDD / 8 Gigas of RAM / Xenon QuadCore.

  ESXI 5.5 (I had two).

  Using Raid 01 (1 TB)

  RAM of 64 Gbite

  Hearts CoreI5 Xenon proceso.

  VCenter server deployment with Vmware Storage appliance.

  Problem:

  I've had enough material resources, in fact, I had twice the disk space and memory to four times more in the reception of news

  When migrating virtual machines in ESXI 4 server and get Vcentener turn it on the message "this VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure.  "

  I do not understand because the servers have resources, I can't find what is wrong.

  Should I use another method of migration?

  Once that you have migrated, can solve this problem without re-migration of computers?

  I found this post, but it's no imformation. This VM could not become vSphere protected HA and HA cannot attempt to restart after failure of.

  Thank you

  See:

  Re: This VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure.

• Differences between the ISCSI connections to the storage in vSphere 4.1 and 5.0.

  I'm in trouble of setting up the connections of storage in a new VSphere 5.0 test environment. In our environment VSphere 4.1, it was possible to create a virtual switch add two Broadcom NetXtreme II 5709 NIC. Set assets. IP Hash value as load balancing. (LACP Etherchannel on physical switches) This configuration uses a grain port and a single IP address. Then add our NetApp NFS storage and ISCSI Equillogic storage. In VSphere 5.0, I can't create this same configuration. I have to create separate with separate IP addresses vmkernal ports? The idea was to have redundant connections to the storage and flow of these two NETWORK cards. Possibly adding additional if necessary to the futuer NETWORK cards. Any help with this would be greatly appreciated.

  How can I work around this:

  "VMkernel network adapter must have an active link exactly and no waiting rising to be eligible for the iSCSI HBA connection."

  I can certainly say that the way which allows you to configure the iSCSI Multipathing is incorrect.

  The main idea is to let Native Multipathing Plugin to decide what network path to choose, not the vSwitch.

  At the level of the network layer, you must have 1 VMK by a physical NIC.

  This technique applies as well for vSphere 4.1 and 5.0, but with the 5.0 it is configured easier and more quickly.

  Here's a very brief consequence of steps

  1. get 2 VMK interfaces and assign an IP by each VMK.

  2. set each VMK to use only one physical NETWORK adapter

  3 GB with storage iSCSI software adapter, turn it on and bind your VMKs 2.

  4 connect to your iSCSI storage space

  5 rescan devices, create the VMFS datastore

  6. set the desired load balancing VMFS method or just set up a prior default create new VMFS

  and it is strongly recommended to read this guide - http://pubs.vmware.com/vsphere-50/topic/com.vmware.ICbase/PDF/vsphere-esxi-vcenter-server-50-storage-guide.pdf

• Fedora 17 office is different under VMware vSphere 4.1 and Workstation 8.0.3

  Fedora 17 office is different under VMware vSphere 4.1 and Workstation 8.0.3

  http://Forum.ICST.org.tw/phpBB/viewtopic.php?f=16 & t = 26288 & sid = 523862dca09b4cf69f52bf9dfdd76086

  Hello

  I'm sorry but I don't understand the position, but if I'm right you wonder why the office are different.

  It is simply because the desktop 8.0.3 Fedora 17 can start the new interface of Gnome 3, on vSphere 4.1, it can be started and Fedora will then be restored in "compatibility mode".

  HTH

  Giuseppe

• How can I get the menu bar with preview in browser and Code, split Code, design to appear? (DW CC) Accidentally deleted and cannot locate.

  I have accidentally disabled Standard or Document to the menu bar, now I can't locate the Code, code split, preview in browser and others.

  How can I get the menu bar with preview in browser and Code, split Code, design to appear? (DW CC)

  Found.  View > toolbars > Document.

• Hello, I made a site using the 3 platforms: desktop, Tablet and smartphone, but... on tablets and smartphones appears the design office, no idea why?

  Hello, I made a site using the 3 platforms: desktop, Tablet and smartphone, but... on tablets and smartphones appears the design office, no idea why?

  Hello

  Please make sure you check "Desktop Redirection" option in the properties of the site.

  Here's how to get there.

  Presentation of the Tablet:

  File > Site Properties > Tablet > check "desktop Redirection.

  Mobile layout:

  File > Site Properties > Mobile > check "desktop Redirection.

  Re-upload the site and then check out. You should be all set.

  If the problem persists, please share the URL of the site for further investigation.

  Concerning

  Vivek

• vSphere 4i? and 4?

  Hey guys,.

  I noticed, vsphere 4 versions and 4i, I guess they're on the lines of 3.5 and 3.5i the latter having does not access the consoles and the smallest footprint.

  I thought vmware away from 4 and was moving in foot print smaller version the 'i' (Please correct my jargon here)

  Is it wise for me to load the host 3.5i with 4 4.5i (upgrade)?

  Please advice

  RJ

  We will all live a virtual life...

  Here are some links worth visiting

  http://KB.VMware.com/kb/1006543

  http://KB.VMware.com/kb/1010579

• "Unable to connect to the MKS: unable to connect to the host [servernamehere] failed on vSphere 4.0 and client.

  Anyone have this problem?  I loaded vSphere 4.0 host ESX 3.5 and everything seems to work very well yesterday, after sleep more testings and this error arose:

  "Unable to connect to the MKS: unable to connect to the host failed on vSphere 4.0 and client.

  After a google search, I could it is resolved by placing the DNS entries on the client machine c:\windows\system32\drivers\etc\hosts file point to my ESX host name and domain name FULL name runs and it worked fine.  I'm curious to know why this went well?

  What is MKS mean in this case?  Server key from Microsoft or the key management server?

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

  Kind regards

  Stefan Nguyen

  VMware vExpert 2009

  iGeek Systems Inc.

  VMware, Citrix, Microsoft Consultant

  When you click on the console of a virtual machine, the server that hosts the vm responds back with its host name for your client to connect to.  Thus, the MKS console could not be connected to, and you could not see the virtual machine console, until you updated name resolution.  Given that the ESX host is back with a name, the customer could not resolve the name, if your client could not connect to the virtual computer mouse, keyboard, screen.  Hope that makes more sense.

  -KjB

  VMware vExpert

• Openfiler and vsphere 4.0 and esx 3.5. possible?

  Hi all

  I with openfiler iscsi san using vmware workstation 6.5 method and worked well.  I wonder if you can install the virtual machine within vsphere 4.0 and esx 3.5 openfiler and create the 80 GB drive and make iscsi san.  Anyone know if this work.  I tried the same method with vmware workstation 6.5 and did not work.  Help me please.

  If it is essentially a test environment POC, it should be fine, but using VMware workstation 6.5 method would be good enough for then why try you this method?  You can use other appliances virtual network of Lefthand, target iSCSI rocket Division, Xtravirt VSA, etc... Or, I place openfiler VM on a laptop or a cheap PC and run as your NFS/iSCSI solution.

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

  Kind regards

  Stefan Nguyen

  VMware vExpert 2009

  iGeek Systems Inc.

  VMware, Citrix, Microsoft Consultant