VW Wkstation 8.0.2 Linux + multiple Ethernet devices

Similar Questions

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• Network preferences do not offer the physical Ethernet devices I (and necessary)

  When configuring network in vmware workstation Linux 9 it offers me only a selection of devices, apparently limited by too simple string-based filtering. I offered my < n > eth named devices, more a Linux already existing bridge.

  However, the device that I need to connect is called "ethmain1", which is a physical ethernet port and the only network where my DHCP and PXE servers are listening.

  There are also way incorrect "eth0", which I do not at all. This makes the automatic setting fails because it selects eth0 that does not exist.

  Is there a text file where I can just tell him the right name?

  Allright, so the answer for later use.  Thanks a lot for the support to help with this.

  / etc/VMware/Networking

  He has a copy, if the list of interfaces that vmware "compound" (people) have a "-1" at the end and it has the interface currently assigned to the gateway for vmware, with a '0' at the end. ".  You cannot edit with a correct list of the interfaces (with the "-1"), however, if you stay just the correct interface in the main entrance (with the '0' in the end, it will keep this setting.

  [code]

  VERSION = 1, 0

  response VNL_DEFAULT_BRIDGE_VNET-1

  add_bridge_mapping bridgestb-1

  eth0 add_bridge_mapping-1

  add_bridge_mapping ethmain1-1

  eth3-1 add_bridge_mapping

  add_bridge_mapping eth5-1

  tap4-1 add_bridge_mapping

  add_bridge_mapping ethmain1 0

  [/ code]

  First line "ethmain1" is ignored, but the last line sticks and things work.

• I want to use my Time Capsule as a backup via ethernet device but it interfere with the Wi - Fi

  I bought a new Time Capsule (TC) to use as a backup device Time Machine.  Then, I learned that my place of work does not allow me to create my own wifi network.  I connected to the CT with an ethernet cable and turned off the wifi using Airport utility.  Automatic backups to decide using just the cable ethernet, as expected.  However, whenever I plug the ethernet cable from the TC to my laptop (MacBook Pro under OS X 10.10.5), the laptop refuses to use the actual wifi to my work network.  It's like the ethernet connection turns off the wifi connection, even if the laptop is always connected to the wifi (according to the network in the banner at the top of the screen icon).  Unplug the cable immediately gives me access wifi again.

  Any suggestions on how to disable this "feature" where to plug the ethernet cable disables the wifi connection?  Thank you very much!

  Note that I have not connected to the LAN Time Capsule.  It is completely autonomous.

• 2000-2d13CA HP: another ethernet device drivers controller/PCI device/PCI simple comunication/controller SM Bus

  I just reinstalled windows 7 on my HP 2000-2d13CA lappy, but problems with the following device drivers:

  Ethernet controller

  PCI device

  PCI simple communication controller

  SM Bus controller

  Please help with the procedure

  Hello:

  First install the smbus controller driver and restart the PC.

  This package contains the driver and Intel Chipset Installation Utility for the notebook models and operating systems. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager.

  File name: sp56670.exe

  Ethernet controller:

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp56680.exe

  PCI device:

  This package contains the driver that allows the Realtek card reader in laptop models running a supported operating system. The card reader allows users to read or write to removable storage cards supported, which are typically used in digital cameras, digital music players and cell phones.

  File name: sp64801.exe

  PCI simple communication controller:

  This package provides the driver Intel Management Engine Interface (MEI) for the notebook models and operating systems. The Intel Management Engine Interface allows communication between the host operating system and the Intel Management Engine firmware.

  File name: sp56675.exe

• How to read the multiple slave devices in a RTU modbus RS485 2-wire network without changing slave address manually?

  Hello

  Currently, I can read data out of multiple using the attached VI DAQ devices by manually changing the address of the slave on the front panel that determines what slave to read the data. However, I want the VI to do it automatically for me instead of me manually by clicking on the buttons on the front panel to change the address of the slave. In other words, the VI should read data off devices 3 slaves and save them to a database of all the 1 second (sampling from 1 sec interval). I tried to use the structures of the case, timed sequences and delays, but I'm still not able to get what I wanted. My current VI is a modified version of a VI library modbus - 'MB series Master query read input registers'. No idea how to do this?

  IM pretty new to LabVIEW, so don't kill me if im away here

  Could replace the cluster 'Series settings' with the attached structure solve this problem?

  The real deal will be just the value back to the default (1).

  -Tom

• Ethernet Device Network Rede Sistema of Rede

  Of Ola gostaria don't saber como o meu pc ligo a cabo (ethernet) of uma por Internet no windows 7... : s

  You posted your question at a Forum on English language.

  Please select your language from the list after clicking on the icon at the bottom of this Web page.

  English

  You can also use this link to find your particular region language:

  http://support.Microsoft.com/common/international.aspx

• Drvice Manager /! ------next to NVIDIA nforce 10 / 100 Mbit/s Ethernet.Device cannot start Code 10

  The product name and number:

  HP Pavilion Dv9700

  s/n [personal information]

  p/n FE395UA #ABA

  Operating system:

  Windows Vista 64-bit

  Current issue:

  When I opened my device manager there are one /! ------next to NVIDIA nforce 10/100 Mbps Ethernet.

  When I open its properties there is a message in the device status, indicating:

  "This device cannot start. (Code 10) »

  It gives me the ability to "Look for solutions", which proved to be unsuccessful.

  Also, I installed the most recent driver.

  Hello:

  If uninstalling and leaving the NIC card get rediscovered and installed the drivers does not work, I recommend you install the nForce chipset driver for your computer that contains the ethernet drivers and see if that gets it.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=ob-55781-1&CC=US&DLC=en&LC=en&os=2100&Product=3686683&sw_lang=

  Paul

• Problem with multiple display devices

  Hello

  I've recently upgraded to Adobe CC and I am trying to configure Edge inspect on my iPad and iPhone.

  I added two devices defined in the instructions, but when I try and get an overview of these two devices, I get the following message:

  Use of multiple devices is a feature of the version complete edge inspect. Upgrade now to connect several devices simultaneously.

  Does this mean I have to buy another upgrade to allow multiple devices to be viewed?

  Any help appreciated.

  see you soon,

  Blue-insurance

  Inspect edge has two pricing options, a free version, which only allows one device to connect to both, and a full version that allows an unlimited number of devices to be connected simultaneously. If you are already subscribed to the full version of edge inspect try to connect log out of the application of edge inspect and then again to solve the problem.

• Time Capsule with multiple OS devices...?

  Is there a recommended way to have a TC to use at home with Mac OS, iOS, and 10 machine a window?

  I'm considering a purchase and to wonder about this as an option for backup/storage for files and Photos, iTunes Library (mainly Mac/IOS), etc. With 10 of the window.

  Ideas, suggestions and shared experience welcome!

  You can save the iTunes library on the TC... It is possible though slower.

  It is not possible to store your library of Photos on the TC... once again, it might work and other people the recommend... but Apple does not support.

  iOS has nothing to do with the storage or backup to a TC either. By default iOS don't not have yet the disk on the TC... you must use file... as filebrowser navigation software.

  Windows is also possible, but problematic. To make backups is probably not possible by using the native software in windows, but many third-party backups will support it... Macrium Reflect is one I use that.

  However the restoration can be much more difficult because the files are not stored in native format.

  If you want a multi-OS device buy a real NAS... Synology is my favourite, although expensive, that they support PC and Mac very well... as well as applications for iOS.

  You will store actually Mac libraries is another matter however because they depend on Mac format so you may create a sparsebundle or DMG file and use it. And this will make sharing... which I think is why you... almost impossible.

  NOTE... If you use not a backup of TC is not possible using Time Machine... and you should back up the files we need to think about the problem... what software to use... Carbon copy clone or chronosync will run... and you need a target disk... USB attached to the TC is the worst... slow place that transport CANADA continues to use USB2.

• Did you notice a delay when the stream to multiple airplay devices?

  I've used a wireless Airport Extreme with Apple TV and 1 or even 2 Airport Express to music streaming at 1-3 stereo systems simultaneously always without delay. Now, using only an AEx and ATV there is an echo of the notice. The system does not wait for the other Aex has become obsolete and is no longer used.

  Make sure that the Apple TV software is up to date > update the software on your Apple TV

• Help for installing automated multiple bluetooth devices?

  Hello! I would like to describe our situation. I maintain computers for our local ambulance service.

  We have five ambulances. Everyone has a Logitech Bluetooth mouse and a Pentax PocketJet 3 Bluetooth printer.

  All the mice and printers are the same model.

  We have three from another manufacturer Toughbook CF-18 portable systems that use Toshiba Bluetooth stack.

  The books are transferred from an ambulance to the ambulance, ambulances are used that date.

  In addition, our policy is that portable computers use a local account with rights to base level 'user '. They cannot add their own bluetooth devices since they are not administrator or power users.

  Therefore, we must ensure that none of the three computers will work with any of 5 mice and 5 printers.

  I then have to wear each of the three books in each of the five ambulances and manually match each notebook with 5 mouse and 5 printers so that all laptops can be used in an ambulance.

  I don't like that I have to add each device, but I don't like that I have to do this manually on each of the 3 computers, and I bring the computer in a nearby physics eahc peripheral (or each device to the computer)

  This seems wrong! I have an inventory of the bluetooth address for each of our 5 mice and printers. You can a device add manually in a way, thanks to a script or command, so he don't need no need to be in physical proximity with the mouse or the keyboard and create a match?

  Ideally, I would like to do ith through a batch file, so I don't have to go through a repetitive cycle of point and click steps...

  Thank you!
  mtoal

  You cannot associate devices if they are not around, because the encryption key will be computed and stored on the host Bluetooth module and the module Bluetooth client (mouse and printer in your case).
  You can of course also configure your mouse in limited user mode if the HID drivers are pre-installed. I think that this is the case by default. Just try it. If this isn't the case, then just edit the file "As.ini" from the Bluetooth stack to pre-install the HID drivers. You can also set in 'Tosbtutl.ini' of the following before installing the battery Bluetooth.

  [AutoSave]
  HID = Enable

  It will start searching for devices (mouse, keyboards) HID when you start "Bluetooth settings".
  Assume that you have configured the same on your laptop, then on two laptop mouse.
  You must press the button of the mouse detection again and click on the mouse icon depending on BT-settings for the mouse work again on the one laptop computer. This is because most mice do not support multi-point connections. If it is supported then it is not necessary. However, it is not necessary to set up a second time.

  Bluetooth profiles are supported by your printer (SPP and HCRP)?

• Remove the multiple VirtualBench device name

  Hello. There is a problem need advice.

  The PC had been link with some Virtuabench, and it remember its device name even if it had not been connetced. This causes the tech lab get confused and often choose the wrong device. Somethimes the Virtualbench had already been hook upward with testing circult. This will result to return the Virtualbench to verify nom_peripherique is not possible.

  Is there a way to remove the unwanted peripheral VirtualBench in the list?

  Thanks and greetings

  ZachHindes wrote:

  If the device is no longer connected, you can remove it by calling the 'delete device' API (http://zone.ni.com/reference/en-XX/help/374540C-01/lciviref/remove_device/). It should be in the range of VirtualBench under "utilities".

  Ugh, I broke the link, and I can't fix it.  http://zone.NI.com/reference/en-XX/help/374540C-01/lciviref/remove_device/

• 1588 with no Ethernet device

  It's a very basic question (since I'm new)

  So if you have a card that synchronize your chassis (PXI-6682) and you connect through a cable on the LAN.

  You also call the necessary APIcalls (niSync_SetTimeReference1588OrdinaryClock & niSync_Start1588).

  And on the other end, you have a device that uses 1588 (PTP) and is also connected to the same LAN...

  Should both the card AND the device note between them automatically?

  For now what is happening is:

  • The PXI-6682 is the master (should be slave)
  • The other device is master

  This means, for me, is that they do not seem to communicate with each other.

  Can someone explain to me a nice step by step what I need to do?

  
  

• Blackfin multiple SPI devices

  Hi guys:

  Sorry to post this question, but I really can't get it to work!

  I can configure each SPI device and they work only, when I try to config 2 devices, I can't just two lines of CS to go up!

  Note: Here is my code, I choose slave select 4 so it is easily accessible via SPI connector to the Board of Directors (PIN 14)... SS1 is pin 9!

  Thanks in advance

  I like your "main.vi" instrument, but unfortunately, I think the AD7476A driver was not designed with several converters a/d in mind, let's dig a little deeper.

  "Declaring Slave Select" command limits the value 1-7, because the SPI device can drive directly only this amount of devices, each of them being validated in accordance with the SPI_FLAG registry. Notice that in the DMA transfer mode (case of pilot AD7476A) CPHA = 0 and SS pins are automatically selected at the beginning of each transfer: for each bit set to one in SPI_FLAG a low pulse will be generated to the corresponding pin! (These bits are set on a per activate slave select or declare slave).

  He had been great if playback turn slaves, but isn't.

  I'm in the island you will not wait 1 MSP for all a/d converters. The AD7476A conversion time is determined by the clock series: the pilot sets the SPI clock on the sampling frequency of 16 times. This is why must be given a higher value in the sample spent at BF AD7476A Control.vi clock:
  For a system with converters a/5 n and 100 KSPS value must be 500000. Inter-channel delay is in this case 2 microseconds, so the difference in time between the first sample of the first string and 5th Channel is 8 us (almost equal to the sampling period), this could be a problem in some applications.

  However, more information is available in the description of the material (ADSP-BF537 Blackfin processor Hardware Reference ), documentation of device driver (C:\Program Analog Devices Devices\VisualDSP 5.0\Blackfin\docs), and drivers of source code (C:\Program Analog Devices Devices\VisualDSP 5.0\Blackfin\lib\src\drivers). Here, I would just say it seems circular buffer are not taken (see VisualDSP 5.0\Blackfin\docs \spi\adi_spi_int.pdf and adi_spi_dma.pdf) and move to solutions:

  1 reconfigure the SPI to use interrupts and use reminders to go through program slaves using BF SPI Control.vi "Select/deselect"slave"(of course, each of the ointments pins must"Declare Slave Select"with BF AD7476A Control.vi or"Activate Slave Select"using BF SPI Control.vi). This will add overhead and, depending on the sampling frequency, you may lose a few samples. Also, there is a limit of only 7 slaves.

  2. turn on DMA for a single word and switch slaves in the callback after each conversion result (of course, this will have the same disadvantages as #1).

  3. Add a simple external hardware to automatically select the a/d converters (for example a counter + decoder clocked by one of the seven pins SS and reset using EIO). Then play with stamps to identify channels (example buffers 1 d with 5 items for converters a/5 n). This will add less overhead, reminders will trigger once a sample of all channels was acquired (or even better after n samples, if the length of the buffer is nx5, etc..)

  All of these solutions, to open and close AD7476a driver only once in the 'main.vi.

  #1 and #2 similar to your posted solution above but the command must be select/deselect for interruptions and toggle for DMA. The slaves should be put in exactly at the end/beginning of each word received.