WAG200G ethernet ports problem

Similar Questions

• UDP communication via secondary ethernet port on the cRIO-9074 problem.

  Hi guys.

  I connected my host pc running LV 2010 my cRIO-9074 port using a main ethernet crossover cable. I want to use the second port ethernet on the cRIO-9074 to read UDP messages, and I want to access these messages on my host. UDP messages are sent from a local network, but for testing I also use a second pc running LV 2010 to send UDP messages.

  I configured the ethernet on the cRIO-9074 ports according to this tutorial: "knowledge base 4E0DGASK: Configure the Ports of double Ethernet on real-time controllers'." " My host and primary ethernet port belong to 'Subnet A' while the second port and the second computer, sending UDP messages belong to 'Subnet B' (at the end of my post I will list the masks of ip addresses and the subnet).

  For simplicity, I used the VI´s of this example as a basis for UDP communication. The "UDPServerOnRemoteTarget.vi", which broadcast messages UDP, will run on the secondary computer. The "UDPClientOnRemoteTarget.vi", which reads messages UDP, will work on my host pc.

  Now, in the 'UDPServerOnRemoteTarget' VI, you must specify two IP addresses (port # remained unchanged at 3363):

  1: the IP address of the ethernet port that will be broadcast UDP messages.

  2: the IP address of the ethernet port that will receive the messages.

  In the #1 case I put the IP address to the IP address of the ethernet on the secondary pc port.

  At the #2 I tried to set the intellectual property: a) IP address of the secondary ethernet port on the cRIO, b) IP address of the ethernet on my host computer port and c) IP address of the primary ethernet port on the cRIO.

  None of the parameters produced results. I also tried to change the port number, which did not help.

  However, if I bypass the cRIO and connect the host pc and the secondary computer directly (by using a cable crossed a regular cat5 ethernet cable), I am able to send and receive UDP messages (the two stand-alone always are on different subnets). I guess that this at least excludes any fault in the VI´s code.

  Does anyone know what I'm doing wrong here? Is it possible at all to read the UDP messages that are sent to the secondary ethernet port on the cRIO my host pc?

  I have searched the entire site OR and forums, but didn't come through all that solved my problem. Most of the other tutorials configuration resembling my case is to import the device sends UDP messages in the project, but which is clearly not possible in my case, or is it?

  My IP settings are:

  cRIO 9074:

  Primary ethernet port: 169.254.62.215

  Secondary ethernet port: 192.168.0.102 (static)

  Host PC: 169.254.58.4

  Secondary PC: 192.168.0.144 (static)

  SubnetMask on all ports are the value 255.255.0.0

  I hope someone out there can help me out.

  Kind regards

  Phat

  Solved.

  Stupid mistake. I was running the VI on the host instead of the cRIO pc, which explains why direct communication between the computers worked. Everything works well when it is compiled for the cRIO.

  Kind regards

  Phat

• UCS-C210-M2 on the problem of gigabit ethernet ports.

  I have 2 x C210 M2 with 2 mother board gigabit ethernet ports and 4 gigabit ethernet ports on a PCI card ports.

  PCI 4 port cards work fine.

  On the 2 ports on the motherboard, I have a problem with ESXi 4.1:

  My 2 ports is auto-negotiation and on the vsphere client speed and duplex of the ports are always displayed correctly.

  The switch network where the server is connected is a C-3560.

  I use this server for Unified Communications, one I see the problem on downloading large files.

  With a virtual machine connection of the unit, when I want to download a file of locale (language file - 650 MB to 1 GB)

  The download progress is displayed in MB and it progresses very slowly as 1 MB every many seconds.

  Whereas, when I use a map PCI 4 port gigabit port, I can see the progression to go at a speed of tens of MB in the same period.

  The only way to have growth to proceed more quickly with the 2 on the main Board gigabit ports, is to set the speed of the 3560 switch

  10 Mbps and half duplex. In this case, when we look at the client vsphere, the gigabit on the server port negotiates to 10 MB - half Dupl.

  and the progress is constant and much faster that it is at this time to 1000 Gb/s Full Dupl.

  Someone has an idea.

  My CIMC firmware version is 1.4.1 and I run ESXi 4.1.0

  Concerning

  Marc - CCIE 2700

  Hello Mark,

  LRO of ESXi feature works well with the Linux kernel (depending on the version of UC apps, they rest RHEL 4.7 / RHEL 5.5)

  Try to turn off RSO on ESXi and check the transfer rate.

  http://docwiki.Cisco.com/wiki/Disable_LRO

  HTH

  Padma

• Ethernet port on iMac 2013 does not connect

  iMac 2013 WiFi works, but slow (25 to 40 Mbps off potential 250 + Mbps. Somedays as fast as 179 Mbps wifi, but not lately) router misplacement slows me down and very hard to change the location of the router. Ethernet cable is good. Cable used to work with the iMac, but now it does not work. Not sure if hardware problem, or if the updates of the AOS has caused. Same cable works always with older macBook and iMac. 270 Mbps with the cable connected to the MacBook. A detailed visual inspection of the port does not bent pins. New looks.  Ports of the router has changed. Changing cables. Reset the router. You wonder if El Capitan or other updates might close port? How to re-enable?

  OS X El Capitan to 10.11.5

  iMac 21, 5 - uh 213

  Processor Intel Core i5 at 2.7 GHz

  8 GB 1600 MHz DDR3

  Broadcom 57766-A1:

  Name: ethernet

  Type: Ethernet Controller

  Bus: PCI

  Vendor ID: 0x14e4

  Device ID: 0 x 1686

  Subsystem Vendor ID: 0x14e4

  Subsystem ID: 0 x 1686

  Revision ID: 0x0001

  Width of the link: x 1

  BSD name: en0

  Kext name: AppleBCM5701Ethernet.kext

  Firmware version: 57766a - v1.13, 0x010e63c4

  Location: /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleBCM570 1Ethernet.kext

  mDNS capable unloading: 68:5 b: 35:7e:f8: ff

  Version: 10.2.0

  In addition, Apple Support recognizes that they broke the Ethernet Ports and suggest that if we:

  "Kernel Extension Configuration Data incompatible Version 3.28.1" we can fix it by going to the command line entries.  However, this version is not on my computer. I have 3.28.2 since 29/02/16 and articles 3.30.1 06/04/16 and 17/04/16.

  They say on the following link:

  If the Ethernet on your Mac has stopped working recently - Apple supports

  If you can connect to Wi - Fi, follow these steps to update to version 3.28.2

  1. Open the activity monitor, located in the Utilities folder of the Applications folder.
  2. Select the CPU tab in the activity monitor, and then type "up-to-date" in the search field. The process of softwareupdated should now be the only listed element.
  3. Open the Terminal application, which is also in your Utilities folder.
  4. Enter this command in a Terminal to upgrade to the current version of the extension of the "Incompatible Kernel Extension Configuration Data" kernel:

     sudo softwareupdate --background

  5. Enter the admin of your OS X user account password when prompted.
  6. Switch to the activity monitor. When using the processor (CPU %) of the process softwareupdated is reset, the extension of the core must be updated.
  7. Select restart in the Apple menu to reboot your Mac.

  I prefer not to do that since I could break it's worse and I 3.28.2 and beyond.

• My Ethernet port is not running iMac mid 2011. Pls help me.

  Hi, I have an iMac 21.5 "mid-2011. My Ethernet port is not working. Is this a software problem? Pls help me.

  Try resetting the SMC reset management system (SCM) controller on your Mac - Apple Support

  Try another ethernet cable.

  He still does not? A report with the information more wrote an effective communities of Apple Support question

• Pavilion HP 11: ethernet port on hp pavilion 11 fried... solution... ?

  Hi all

  new to the forum here and decided to join because I have a little problem with my laptop...

  I did something stupid today. I tried to program a hitachi PLC with my laptop and accidentally hooked the ethernet cable to the port of evil on the controller (the port that would normally connect to a touchscreen / HMI) with the result that my port ethernet on my laptop got fried. After a few seconds smoke started coming on my laptop from under the keyboard so I quickly janked out cable ethernet. It's only there for a few seconds, but the damage was already done.

  On the good side of things: everything seems to work OK again. WiFi still works. Only problem is that this laptop has a single ethernet port and I really need this port.

  I took the cover but nothing obvious comes out. I know it's kind of a vague question to ask; but someone would have ideas on what could have broken and how to check what might be broken and what not?

  I'm not very familiar with computers is passing, so forgive my lack of knowledge.

  Thanks in advance

  A network card is not present, there is a wireless adapter.

  Ultrabooks like yours with RJ-45 ports do not have separate wired adapters that can be replaced.

  The NETWORK adapter is part of the motherboard and is not replaceable individually.

  Given that yours was smoked checked there may be some damage of traces on the motherboard.

  With the help of a mulitimeter won't help in any way. Even at big books in ancient times the NIC was part of the motherboard. A ultrabook is not a desktop computer. Motherboards same office have the network cards integrated into the chipset.

  Replacing a motherboard, this is how your network port fried will have to be resolved. Otherwise, to avoid the cost of replacing the motherboard, use the USB cable card NETWORK adapter.

  Under the guarantee, the induced lesions of the RJ-45 port owner is not covered. It's an excluded damage type.

• Ethernet port disappears

  I'm on a MacBook Pro, end of 2013, El Capitan 10.11.3 running.

  Just today, I went to run a test using my Ethernet card rather than my wireless adapter and I couldn't connect.  I spent more than an hour to get to the next State:

  1. The operating system cannot see the Ethernet port.  If I run the system information report the Ethernet port is not listed.  Initially, I got the Ethernet port defined in my automatic position.  When I opened and went to advanced-> Hardware, I couldn't see my mac address and the configuration was virtually empty.
  2. After that a lot of research I restarted with the ethernet cable is connected and press command + r.  When the diagnosis came, I select Network Diagnostics.  There, I could see my card Ethernet, the mac address and the assigned IP address.  I disconnected the cable and saw the idle connection.  I reconnected it the cable and the returned connection active.
  3. I tried to reset the NVRAM using the Option + command + r + p, but without success.

  It is clear that the hardware is functional.

  How to restore the connection in the operating system?  I tried to add manually the ethernet card, but because the operating system does not see the adapter is not available to add manually to the location.

  I need help solving this problem.

  Hi George:

  Found this information. See if she can relate to you. http://9to5Mac.com/2016/02/28/Apple-confirms-OS-x-update-broke-Ethernet-port-on-some-Macs-heres-how-to-fix/

  Kim

• The bridge network to the ethernet ports

  I have an Airport Extreme base station for my wireless at home. The problem I have is that the base station is not near a few features, that I need to hard wire. I read that you can set up a network bridge and if I understand correctly, this concept, it's like setting up of another wireless device, but this second device provides you with the required Ethernet ports for connectivity. Is it possible to do with the Airport Express secondary device?

  Most of the other posts that I read said to extend the wireless range, but the range of my base station is not the issue. I just need a couple on the way ports. I've heard this can slow down the entire network however. Is this feasible? All known reserves? Advice is appreciated.

  Is it possible to do with the Airport Express secondary device?

  Yes

  Most of the other posts that I read said to extend the wireless range, but the range of my base station is not the issue. I just need a couple on the way ports. I've heard this can slow down the entire network but

  It all depends on if you configure the AirPort Express to "extend" the network... which will lower the maximum speed potential of the network by all 40-50%...or...whether that you set up the base AirPort Express for simply to 'join' the network... which causes a decrease in the speed of the network... but it will provide 2-port Ethernet for wired devices.

  If you need more than 2 ports Ethernet on the Express, you can add an Ethernet 5 port, 8-port switch, etc., to create as many ports as you need.

  Don't know what kind of speed you need for the Ethernet ports, but they are limited to 100 Mbps, then that would be the maximum speed available ports Ethernet on the Express.

• Mac Pro does not recognize the Ethernet ports

  After a reboot for my end of 2013 Mac Pro OS x 10.11.3, the two Ethernet ports are most recognized. Suffice to say not 'connected' is one of them.

  I have:

  • rebooted a couple of times
  • Reset the PRAM
  • the power disconnected for several minutes left
  • tried two different terminals
  • tried two different Ethernet cables
  • tried the two Ethernet ports

  The light of the end device will blink.

  WiFi works fine.

  What should I do before I decide that there is a hardware problem?

  Bob

  There was a recent post about the same problem and found a solution. Give it a try: Re-built-in ethernet disappeared.

• Ethernet port does not

  We have 2 iMac and today ports Ethernet on every one of them stopped working.  The cable into each of them works (tested with a Macbook Pro) and I still can not work for every iMac with a USB Ethernet adapter ethernet cable.  How diagnose or reset these Ethernet ports and get them working again?

  Tim

  It's weird, we have the same problem, I have mac pro El capitan end 2013. The two Ethernet is no longer detected but seeing liaison is present... It was fine last night and after starting this morning, it does not work

• ThinkPad onelink pro dock carbon lenovo x 1 Ethernet port has stopped working

  Hello guys,.

  So after a few windows security updates my docking station ethernet port stopped working, it does not detect a physical cable connected. I've upgraded to the latest firmware for the dock but no luck, stops on the port to save energy also. If I connect the cable directly to my X 1 using the adapter of the eth-miniDP I get connectivity very well using the same cable and B end port.

  Update security for Windows 7 for x 64-based systems (KB3046269)

  Update security for Windows 7 for x 64-based systems (KB3042553)

  Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x 64-based

  Update security for Windows 7 for x 64-based systems (KB3045685)

  Update of security for Microsoft .NET Framework 4.5, 4.5.1 and 4.5.2 on Windows 7, Vista, Server 2008, Server 2008 R2 x 64 (KB3037581)

  Kind regards

  Andy

  In response to the client noted that when X 1 carbon ThinkPads (Type: 20FB and 20FB) running Windows 7 are moored via a Dock among +, ethernet does not work, Lenovo has presented a solution via the updated USB 3.0 driver.

  Version 4.0.6.60

  (Fix) Fixed a problem where the device USB-Ethernet among + Dock was unstable when you fix the dock.

  The latest driver for USB 3.0 can be downloaded here: http://support.lenovo.com/us/en/downloads/ds111779

  Thank you

• RN102 fuel, ethernet port with a light

  Hello

  I have a problem with one of our readynas it will not feed.

  When I plug the power in no fan activity and no lights on the front, but the ethernet port has a light.

  I tried the adapter in a voltmeter and everything is ok.

  Any other suggestions?

  NETGEAR talked and got a replacememnt warranty unit was dead, put hard drives in all and save work without data loss.

• How can I transfer the mail, Safari, iTunes, etc of my 2008 MacBook running OS 10.5.8, a new MacBook Pro (with Ethernet port) or a new MacBook Air?

  I replace my 2008 Macbook which maxed out at OS 10.5.8, with a new MacBook Pro or MacBook Air.  The Pro has an Ethernet port, the Air is not.  I want to transfer all the data from my application (mail, Safari, iTunes, etc.) for the new Macbook that will run El Capitan.  How can I do?

  What machine you're leaning towards? With Air, you have to use ether WIFI or have the old drive on an external drive configuration. With a new Macbook Pro, the simplest method is to use the migration assistant. Access your Macbook in public services and to see, there you have it. Here is a link to what you can do.  http://pondini.org/OSX/SetupLion.html It is said Lion, but it applies the same. Here's what apple says.  https://support.Apple.com/en-us/HT204350 you should know that some of the apps in Leopard will be obsolete in El Captian. There you transfer, it can cause problems. I use the thinking that if I can replace it with a download I do this. The transfer or, if there is an update for it.

• HP Pavilion # 21 - h014: how to enable the ethernet port

  I can not connect to my modem by ethernet cable. How can I activate this port? HP pavilion model #21 - h014

  At the back of the PC ethernet port must be enabled at any time, unless the Device Manager shows that there is a problem.  The ethernet cable is maybe defective.  OR  Just to the right diagnosis, what is the brand and model of the modem and port on which you connect to the modem and then to PC.

• my modem STC (Saudi Arabia) SAGEM 007 has 4 ethernet ports. two of them do not work. (in red)

  my modem STC (Saudi Arabia) SAGEM 007 has 4 ethernet ports. two of them do not work. (in red)

  Hello

  You should check with the help of the manufacturer modem and if it is provided by your ISP support.

  Not really a Windows problem.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">