Similar Questions

• X 8 Dual Gigabit Ethernet Port Aggregation easily explained?

  Can you explain what that means?

  • Dual Gigabit Ethernet Port Aggregation

  In a totally non savy way

  @careyjames LACP is not available in AP mode.

• How can I connect to xbox live on the internet with an ethernet port?

  I am currently in College and I have tried everything to connect my xbox to xbox live.  I entered the IP address, subnet, gateway and DNS settings, and I have not yet connected to my network.  What is the problem?

  Not the right forum to do this, but I will try to follow if/when it is moved.  You can also try http://forums.xbox.com

  If it is an Xbox 360 with NXE (dashboard updated):

  -When you go to the "chain of the system" (extreme-right under "my Xbox" on the dashboard), go to network, and then test the network connection.  See if any of the suggestions here correspond to the you receive the error message:
  http://support.Xbox.com/support/en/us/NXE/xboxlive/troubleshooting/gettingconnectederrorslist.aspx

  Nu WinBreak.com - video game Fanblogging

• UCS-C210 m2 low IOPS / s

  I currently have a case for it with cisco, but I thought that I post to the community to seek one advises...

  I have 2 ucs c210 servers,

  The two are almost identical.

  Ucs1 - has 24 sons of CPU power and 32 GB of ram,

  Ucs2 - has 16 sons of CPU and 48 gb of ram.

  Other then that they both have the same server - win2k8 r2 running hyperv bones

  Same raid configuration and even hard disks.

  UCS 1 becomes significantly more high IOPS / s

  This becomes increasingly more clear when a comment server benchmarking.

  Joined landmarks of comments on each server (migration)

  I swapped the raid under wty with Cisco card, but the performance was not improved.

  Then.

  Other thoughts about the large performance difference?

  Would it be a windows affecting one somewhere I missed?

  Or is a card or mother or other hardware failure?

  Sent by Cisco Support technique iPad App

  Hi Robert,.

  Thanks for the update

  Performance decreases in Windows Server 2008 R2 when the Hyper-V role is installed on a computer that uses Intel Westmere and Sandy Bridge processors

• I run xp coffeehouse get an icon remove the device safely. I check it and it is for a card broadcom netlink gigabit ethernet which can not be deleted

  I run xp family on a computer laptop hp compaq 6510 b.  The broadcom netlink gigabit ethernet adapter is part of my motherboard.  Why do it and can I get rid of him?

  Hello

  1 have had any changes made to the computer before the show?

  Restore the system to the date and time when the computer was working fine.

  http://support.Microsoft.com/kb/306084

  If this message has always been to present its likely that the Ethernet card that is built into the computer is connected to the motherboard using a USB connection (this is common in laptops). If this is the case, there is nothing that can be done to remove the message that the deactivation of the Ethernet card, but this will prevent you from being able to use wired Internet/network connections.

• Driver Intel® 82566 Gigabit Ethernet for windows 8

  Is there a 32-bit Windows 8 for the Intel® 82566DC Gigabit Ethernet driver. The latest version I have is 9.13.41.1. I had problems because I installed 8 32-bit windows, because when I recover from hibernate my LAN adapter will not connect. The adapter turns off and I have to restart to activate again.  hard decisions have no problem.

  I looked at the forums elsewhere and have disabled the Microsoft Kernel debug network card. This can work. Other options?

  Hello

  Glad to know that you have addressed the issue. If you have any questions about Windows in the future, please let us know. We will be happy to help you.

• How can I transfer the mail, Safari, iTunes, etc of my 2008 MacBook running OS 10.5.8, a new MacBook Pro (with Ethernet port) or a new MacBook Air?

  I replace my 2008 Macbook which maxed out at OS 10.5.8, with a new MacBook Pro or MacBook Air.  The Pro has an Ethernet port, the Air is not.  I want to transfer all the data from my application (mail, Safari, iTunes, etc.) for the new Macbook that will run El Capitan.  How can I do?

  What machine you're leaning towards? With Air, you have to use ether WIFI or have the old drive on an external drive configuration. With a new Macbook Pro, the simplest method is to use the migration assistant. Access your Macbook in public services and to see, there you have it. Here is a link to what you can do.  http://pondini.org/OSX/SetupLion.html It is said Lion, but it applies the same. Here's what apple says.  https://support.Apple.com/en-us/HT204350 you should know that some of the apps in Leopard will be obsolete in El Captian. There you transfer, it can cause problems. I use the thinking that if I can replace it with a download I do this. The transfer or, if there is an update for it.

• The computer hangs during the communication via a serial port

  I developed a code in LabVIEW 2011 to connect with the XY stage. It's actually two steps mounted perpendicularly. The installer of the system is that a (made by the same manufacturer as the stadium) gamepad is connected to the USB port on the computer if a USB to Serial converter. A step is daisy chanied to the controller and the other stage Garland at the first stage.

  To our application had to continually check the status and position of the steps X and Y. Because the joystick also returns responses when a request is sent to all devices, I need to send applications individually; for example. one request per order per device, making it a total of 4 orders. It takes care of the error returned by the controller. The problem, however, is that after a while the freezing of the program or the computer stops and restarts. It is located about 13 minutes (on average) after the start of the program. It also happens even when no command is sent to the devices. I put 50 ms delay before each send two commands (position and status) by device. Basically, the application waits for 50ms before sending two commands for X stage and the receipt of the response and when everything is done with X stage, he expects another 50 ms to do the same for step Y. Should this procedure goes on until the application is stopped. But as I said, there is a problem. Now, I guess the problem is that serial port buffer overflows. He chose to increase the delay time, but if it works to solve the problem, then I have no choice!

  I would appreciate any thoughts and comments!

  After a lot of time to experiment, I am convinced that the issue was with adapter Profilic.

• W520 PCI - E gigabit ethernet card

  Hello

  There is a PCI-E on the side slot on the W520.

  Are there of the PCI-E gigabit ethernet cards available somewhere for this port?

  I looked around but have not found.

  Kind regards

  Eddy.

  http://www.CDW.com/shop/products/Belkin-Gigabit-Ethernet-ExpressCard/1001280.aspx?AcquirgyID=1421650...

• This device cannot start. (Code 10) Windows 7 64 bit JMicron PCIe Gigabit Ethernet Adapter

  Apparently, I get this error at random times in the day.  My ethernet port just no longer works and I tried disabling and reactivation that used to (a while back) work.

  Then recently I was disabling and re-enabling it, it gets stuck in the 'disabled' and this error message appears when I open "Properties".  I tried to reinstall the drivers for the device with the CD of my laptop came with, but that has not worked so I looked on the site Web of Jmicron and found a newer driver who, after installing again, did not work.  I have a fixed work wireless, but not with no LAN no is a pain in the thigh.

  WIndows 7 64 bit Home Premium edition
  Sager NP 5165 Notebook
  JMicron PCI Express Gigabit Ethernet adapt

  Try to update the laptop bios and chipset software provided by your computer laptop oem (dell, hp, whoever). Fixed an instance I had 10 with a device error.

• Using the second ethernet port to connect to the printer?

  Hi I have a Mac Pro 2.1 old school and I'm wondering if I can connect to the network with an ethernet port and connect the latter to a printer?

  If so, how?

  Yosemite running.

  Thank you

  Physically, you use a port and a cable to connect to your network and use the second port and a second cable to connect directly to the printer. The printer must obviously have an interface Ethernet himself.

  However, you need to configure the second port on the Mac and the Ethernet port on the printer for each manually configured the TCP/IP addresses and these should be in a range of different network to your main network.

  If you the main network is something like 192.168.1.1 then your printer and the port on the Mac connection to this need to be in another network, such as 192.168.11.1.

  In theory, if the printer supports Hello aka. mDNS, then maybe you can get away with not having to configure TCP/IP addresses for the connection.

  The main reasons to use a second separate connection as this would be the performance or security, and frankly I don't think that's really relevant here. This would mean that no other computers on your network will be able to access the printer.

• New UCS-C210 problem with video monitor output

  Hi all

  We just bought a new Cisco UCS C210 M2 product for our CUCM migration to Virtual Machines. We plugged a HP monitor and a USB keyboard to start work with the UCS. Then we plugged the server to the power supply and turn on the server, the fan worked properly for his initial shot. However, I could not see the monitor up and I can't see if it boots correctly. We waited and notice that the keyboard seems to work as you can see the num and lock the scroll works.

  I unplugged the monitor of the connection of the console before the use of the foxconn connector that came with it and plugged into the DB15 port on the back. Same result the monitor does not display anything.

  So I went on the second UCS server using the same keyboard and mouse, everything works.

  Any who know this problem of the screen does not? If so, please share how to fix it.

  Otherwise, our conclusion would be that Cisco sent us a faulty hardware or it has become defective during the transport.

  Thank you best regards &,.

  Ramon

  OK fans turn upwards and then downwards with the lights on the front would indicate to me that the server itself is ok and boot up normally. The fact that you have used this monitor UCS one another in the same way seems to indicate that the problem is probably with this server and a video on the issue. I suggest to open a TAC case and include these steps you have taken. If you can, try reinstalling all your memory and boot up the server again.

  I hope this helps.

  Sent by Cisco Support technique iPhone App

• Cisco UCS C210 M2: PXE - E61: Media test failure, check cable of

  Hello

  I'm working on Cisco UCS C210 M2 servers. I got 10 146 GB SAS HD with LSI MegaRAID Raid Controller. I did run the Raid Controller and choose RAID6. After that I installed ESXi and it said to reboot the server. Now, when I restart the server I get the following error message:

  PXE - E61: Media test failure, check cable of

  PXE - M0F: Exit Boradcom PXE ROM

  Restart, and then select proper boot service

  or Insert Boot Media in some boot device and press a key

  Any suggestions how I can solve this problem.

  Thank you.

  You will need to go into the Bios of the controller LSI MegaRaid (Ctrl + H) and select the option of virtual drives on the left. When the virtual command window opens, you must select the drive (Raid Volume) on which you want your drive master boot and underneath there will be an option to set as your boot device. Apply and save.

• UCS-C210 Firmware

  When I try to update the firmware via TFTP I get an error message Image_CRC_Failure on the web and CLI.  I tried to re - upload the image and I tried several versions of the image.  I also tried the upgrade via the web and I get to 5%, and the system hangs.  When I try to log in I get this error message: "this browser has already a MMIC session. Only one session is allowed by the browser. You must log on to the other session, connect with a new session. "I click on the link"Logout of the other session", but I can not always log in.  I have to completely power off the server for the Web to become available.  When I say "shut down", I want to say that I physically remove the cable from the back and wait 10 seconds.

  Could someone tell me please the right way with these 2 questions?  It is the first time that I had the chance to work with the UCS-C210 and I'm about to say that I'm not impressed because this isn't the first question that I met.  I like Cisco and I won't get that far right now.

  Any help is appreciated,

  Terry

  Hello Terry,

  These types of problems are usuing the fault of a Windows TFTP server cause CRC errors.   Have you tried downloading interface Web of another client by chance?

  Have you tried the HUU (Host Update Utility)?  It's an ISO you just go up and it will update all FW components as you like.

  You can get it here:

  http://www.Cisco.com/Cisco/software/release.html?mdfid=283862069&flowid=25882&softwareid=283850974&release=1.4%281C%29&relind=available&rellifecycle=&RelType=latest

  * Note the name of the file will be called something like "ucs -c200- huu - x.x.x.iso", but that's fine.  The C200 and C210 are the same basic architecture, and this package is compatible with both.

  As for your other questions, you can configure the MMIC to allow multiple connections: it's under Admin settings or Communication, I think.  By resetting the MMIC (not disturbing for the host operating system), you can clear all 'stuck' sessions.

  Let me know how you go and we'll get you squared away, I promise you.

  Kind regards

  Robert

• UCS-C210 m2 fan speed issues

  one of my servers has fans will quickly 6 to 8 k.

  

  My second server of similar configuration is at a normal speed around 2 K.

  I had this happen in the past and I think that I've updated the firmware which seemed to fix. but it seems to have reappeared.

  I restarted the server, and the fans are always go fast.

  both servers are running the BIOS

  C200.1.4.1.0 (Build Date: 13/07/2011)

  CIMC

  

  ======

  Update:

  Earlier, I tested just as to completely stop the server and restart that seems to have helped.

  except now only PSU fans go around 5 K

  the system fans seem to have stabilized to the normal range of 2 to 3K.

  

  my other UCS Server PSU fans are running at 2-2. 5 k.

  Temperature is not a problem, they are both running around same time.

  .. and are both under minimum load

  any ideas as to why the power supply fans are vivid?

  Hi Robert,.

  I guess I must also point out that your two servers have two different versions of them supply systems which explains the differences of stabilized power supply fan accelerates even after having worked around the bug, in my opinion, one of the servers may have met.  UCS-c200 has older PSUS that have two fans online so that fans can run a low speed to maintain the required temperature.  UCS-c210 m2 has newer power supplies that have only a single fan in them so they run the fans at higher speeds to maintain the required temperature.

  Mike