WAP 4400N cannot access the access point

Similar Questions

• Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."

  Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."  How can this be repaired?

  Hi rebick,.

  Try the troubleshooting steps presented by spirit X in this thread.

  Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot move the anchor points using the Subselection tool? (CS5)

  Hey.
  I experienced an intermittent problem in Flash CS5, where sometimes I can't push anything using the Subselection tool. Sometimes, I can, but most of the time I can't and I don't know why.

  I can still click-and - drag points (or multiple points/paths), but I can't push the keyboard.

  Any ideas?

  My guess is that the item is grouped and you are inside the publishing group? For some reason any in this case you cannot move the points in this way.

  Separate the Group and try again. Sorry that's the only answer I know.

• Cannot open the synaptics pointing device in windows vista, upgrades are far but message error, unable to connect to the synaptics pointing device

  Hi I have a problem with my mouse/pointer when I click on the mouse to open it I have error message unable to connect to the synaptics pointing device. Have you checked the updates that are up-to-date, and the driver is ok, not sure what to try next need to make any changes to the mouse pointer

  with Brice thanks.

  Hi paiyay,

  Thanks for posting in the Microsoft Community.

  I understand that you are unable to open the synaptics pointing device in windows vista

  · You did changes to the computer before the show?

  · What happens when you click the Yes button in the error message?

  · You are able to use the mouse on the system?

  I suggest you uninstall the software from programs and features and then try to open the properties of the mouse and check if you are able to open the mouse properties then I would you recommend to uninstall the drivers that are installed on the system in the Device Manager and then download the drivers from the link below and check if the problem is resolved.

  http://www.Synaptics.com/support/drivers

  http://www.Synaptics.com/resources/drivers

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Connect the hard disk, and then try running the fix tool of the article below and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/

  I suggest you to contact the mouse manufacturer for assistance. Click on the link below.

  http://www.Synaptics.com/

  See also:

  FAQ and troubleshooting

  http://www.Synaptics.com/resources/consumer-tips

• Cannot move the anchor point?

  I use CS4.

  When I try to select an anchor point, the actions I take immediately highlight the position and position - not the anchor. I use the selection tool - is not serious if I select the layers or via screen - same thing happens.

  Any thoughts?

  Thank you!

  If you use the Pan behind tool (keyboard shortcut is the key there) and enter the anchor point, the anchor moves relative to the layer, but does not move the apparent position of the layer in the composition. If you check the position values in the timeline panel, you will see that they change when you drag the anchor around the layer.

  

  If you enter values of anchor point in the timeline panel, the relative position of the layer seems to be moving in the composition window, but the position of the values do not change because the position of the anchor point is not mobile at the composition level.

  The value of the position of a layer is always the position of the anchor from the composition. The value of the anchor point is the position of the anchor relative to the layer. Rotation and scale centered around the anchor point of the two.

  I hope this helps.

• Cannot locate the entry point in msvcrt.dll

  During the installation of my program (created with LabWindows 'Building Distribution') on a specific computer, I get the following error:

  "The point_except_handler4_common of procedure not found entry into the dynamic link library msvcrt.dll."

  I understand that this is usually due to an older dll being on the computer for installation compared to the dll with which he was connected, and I checked, this is the case.

  The target computer is running on all the updates, but the target computer is Windows XP, while the development computer is Windows 7.  I have problems with this configuration with other programs, but maybe other programs weren't looking at this entry point.   Setup has successfully installed on other Windows 7 machines.

  Any ideas?

  Thank you!

  Angie

  Something to check is to make sure that the distribution kit does not include the Windows system files in the distribution of PC development kit.  She can do if you have libraries in your project from the kit of development Windows or DDK (as ShFolder.lib).  In this case the end generally install and run software on a computer running the same version of Windows as the development machine, but all kinds of problems occur when you try to install on another version.

• It is said that cannot find the entry point for Muse and Photoshop? I JUST downloaded.

  

  Please see:

  does not start in Photoshop cs6

  The procedure entry point AMTRetrievePersonGUIDWithAuthSource impossible to find the ERROR.

  I hope this helps.

  Concerning

  Megha Rawat

• Cannot change the registration point

  I am creating a preloader type needle gauge and I created the needle and it's a MC and set point alignment in the Middle at the bottom, but it is still running on a center axis.

  Any help?

  This is the tutorial I'm following:

  http://active.tutsplus.com/tutorials/ActionScript/Display-Data-with-funky-Animated-Needle-/ gauges

  Open your movieclip to edit and manually move the chart of the needle, so that the line of sight of registration where you want.

• WET11 V2 cannot be connected to the AP (access point) via WiFi

  I am facing following problem.

  Someone at - he advice me please how to solve these problems.

  Purpose:

  1. I want to use internet on TV Sony Bravia. (Bravia has no WiFI. "I have only LAN).

  Environment:

  1 access point (Router) - WiFi > WET11 V2 - LAN > TV (Sony Bravia).

  2. IP address 192.168.1.5 = WET11 (automatically not static)

  BOF WET11 V2 assigned IP address access point.
  I checked the access point access point IP attributed to WET11.

  3 TV IP address is automatically.

  But the IP address is unaffected for television.

  4 WET11 firmware version = V2.05 (Sep 16, 2003)

  Problem:

  1. IP address cannot be assigned for television.

  2 WET11 is not the answer for the command 'ping 192.168.1.5' WiFi access point.

  3. I did ping command when the LAN TV cable has been replaced by the wireless access point LAN cable.

  BR

  Mutt

  It is not advisable to use a 802. 11B wireless bridge on a device such as your streaming media TV. Connection will be very slow and is probably the reason why you have a hard time to connect to your wireless router that's more compatible with it. I suggest using a Wireless N bridge or a multimedia wireless on your TV adapter so that you can fully appreciate the media streaming.

• Windows automatically restarts constantly, cannot access the system restore point, cannot access the computer in safe mode

  Hi all

  For the not 24 hours I tried to access my computer in normal mode. When I turn on the pc, it says "configuration data 1 of 3 steps...". 0% complete"he never spent 0% and within seconds, it automatically restarts and starts again. It's so frustrating! I have a windows vista pc (purchased in ' 06). I can only access my desktop in SafeMode.

  I tried to perform a system restore, but not like he says "recovery disk is not the restore point selected. What should I do? I tried to manually create a restore point, but cannot access the system and Maintenance, while in safe mode. I can't do anything but literally access the internet. How can I get Windows back to factory settings it is with these limited resources? I have a Dell reinstallation DVD.

  I searched my programs and found that recently Windows automatically updated and downloaded "Microsoft Powerpoint Viewer" and "for 2007 Office system Compatibility Pack '. Now, I think it has something to do with it, because they were the most recent updates, before the pc crashed. But I also fear that it may be a virus, which has completely hijacked this PC. How am I supposed to get rid of a bug, if I can't even get the necessary antivirus?

  Sorry for the ranting, but it's so stressful when my pc is completely down. Please, please please help me. Thank you in advance for reading this same!

  Arianne

  Hello

  you talk about restore and system recovery disc in the same breath

  they are 2 different things

  and you can NOT create a restore of yesterday and today!

  yesterday is gone

  If it does not already; You can't do

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  The malware removal:

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Reinstall vista from Dell DVD

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

• On my user account on my labtop when I click on a program, such as mozilla firefox, it happens 'windows cannot access the specified device, path or file. May not be the appropriate permissions for access you point. "Please help

  On my user account on my labtop when I click on a program, such as mozilla firefox, it happens 'windows cannot access the specified device, path or file. May not be the appropriate permissions for access you point. "This message appears for firefox, AVG, Windows live messenger, windows MediaPlayer etc.

  I can access my documents, Panel etc. and everything is there, but it won't let me not get access to the programs.

  Also when I go to click on itunes and open office it happens "this file has no program associated with it for performing this action. Create an association in the set associations Control Panel.

  Given that I was able to access control panel, I was able to create a new user and use it for now to send this message and all programs have worked on it and I was able to check for the presence of viruses on the Avg on this and everything was clear.

  Could you please explain whats wrong and tell me how to fix this please: D thanks

  Hello
   
  1. don't you make changes before the show?
  2. is the computer is joined to the domain controller?
   
  You can not start any application on a client computer that is joined to the domain controller. When you try to start this type of application, you receive an error message similar to the following:
  "Windows cannot access the specified device, path or file. You can not have the appropriate permissions to access the item.

  This can also occur if the user account is damaged. If the computer is not connected to a domain controller, try the following steps.
  1. connect to another user account and create a new user account to fix the damaged user account.
  For more information about creating a new user account and the fixing corrupt user account, visit this link: http://windows.microsoft.com/en-US/windows-vista/Fix-a-corrupted-user-profile
   
  Previous post the results in more detail, so that we can help you further.
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Access Point WRT1900AC & Firmware version: 1.1.10.167514, it cannot be accessed the config page.

  Hello!

  I am a new user of router dual-band WRT1900AC . The installation has been updated instantly to
  Firmware version: 1.1.10.167514
  Release date: June 30, 2015

  My WRT1900AC is configured as a wireless gateway.

  https://community.Linksys.com/T5/wireless-routers/WRT1900AC-as-wireless-access-point/TD-p/847286

  Also, I have disabled firewall and uPnP.
  A tutorial here:

  http://www.Linksys.com/us/support-article?articleNum=140371

  Everything works except that without access to the router config page.

  The problem is, I can't access my page to config WRT1900AC Wireless Access Point and the only solution is to connect temporary exit HAND ROUTER LAN to WAN WRT1900AC, can I access my AP

  (after restart of course). Change after I return the cable to the LAN again and restart WRT1900AC. This works.

  Yesterday, I spoke with live chat. I received recommendations:
  "Once the router is configured to bridge fashion, page configuration accessible only using its new IP address. The new IP address can be found on the main router DHCP table. It is because only in LAN - LAN, the

  WRT1900AC will be his disabled DHCP. »

  I also saw Table of customer routers main DHCP but I have not found the IP address of my wireless WRT1900AC Access Point there. I think it is a bug in the version of the Firmware: 1.1.10.167514
  Page config in the case of WRT1900AC Wireless Access Point is isolated or possible only thanks to the WAN WRT1900AC. It would be nice if someone confirms that and maybe in the next version of

  fix. :-) I have a beautiful smartphone App "Smart Wi - Fi" and I can not comfortably use it due to this error/bug.
  Otherwise everything works well and stably.

  inspire wrote:

  Hi chadster766!

  Thanks for your suggestion and a quick response. I have a feeling it would work then as you described. But how to set Internet settings in mode Bridge? I've already put a static IP address router IP address WRT1900AC. I see it with IP scanner.
  If I leave the cables as you suggest (hand router LAN to WAN WRT1900AC), the Internet does not work. In this case go to the config page, but Internet with other devices will not work. Also good Wifi, it works but can not access. How to set the Bridge Mode? (I think this is my problem in this scenario)

  IP address of the router (LAN):

  Connectivity-online-online details router LAN => Edit

  * If your main router IP subnet example is 192.168.0.x, then set the address of the WRT1900AC IP to an IP outside the range of the main router DHCP. Ex: 192.168.0.2

  Bridge mode:
  Connectivity-online Internet-online IPv4 settings => Edit-online Bridge Mode

• Cannot associate the Access Point

  I just bought a WUSB54GSC wireless adapter and try to connect to my wireless router, a WRT54GS2, but it gives me a message saying "can't associate with the Access Point.  I tried several times and tried to reconfigure the WEP key, just in case I screwed up somehow and get this message.  I tried the network unsecured neighbor (signal low, of course) and he gave me the same, too.

  What I know:

  (1) the problem is not with any part of my network, either from my lines (DSL), (ADSL) modem or a router, because I use a wired network right now with no problems and several other devices in my house with built-in WiFi to connect wireless to the same router with the Setup even very well.

  (2) the problem is not that I messed up the WEP key.  I rechecked it multiplies and even went to the router via an Ethernet cable to check what I entered compared to what he shows me, and they have a perfect match.  In addition, as previously stated, various WiFi compatible devices in my house using the same WEP key to connect properly.

  So, I don't understand why I can't connect what either.

  First go to device manage and check if the adapter is installed correctly or not... ? If it is installed correctly then, right-click on the utility of linksys (green square) on the toolbar and click on 'Use Windows to configure' and click on 'yes '...

  Now, if you have Windows XP... Click Start and goto the control panel and double-click on network connections, right click wireless network connection and click View available wireless networks and select your wireless network and click on connect... Now, it will give you the opportunity to put the network/wep key, make sure that you enter the correct network key and confirm... It will connect...

  If you have Windows Vista... Click Start > Control Panel > Network and Sharing Center > click on connect to a network, select your wireless network and click on connect, it should ask for your key/password network, enter the network and password correct key and click on connect... It needs to connect... Once you're connected, you must restart the computer, it needs to connect to the Internet...

  Also try to change the wireless channel of the router to 11-2, 462 GHz and then try again...

• C4780 wireless printer cannot find the access point

  I have c4780 wireless printer.  It will print fine using the usb connection, but has never printed wireless.

  PC operating system is Windows Vista.  Wireless router is the linksys WRT54G.  The printer does not see the access point.  The security mode of the router is WPA Personal.  I have a unique SSID.  ISP is Timewarner Roadrunner.

  How do I get this to a wireless connection?

  Try this firmware update.

  In addition, sweat you are broadcasting your SSID and not using MAC filtering.

• Have ELPH 135... and cannot access the LIVE mode... when I push the arrow pointing upwards I get monochrome ir auto... Help?

  I can't in Live mode... When I press the arrow pointing upwards, I get only auto or monochrome.  It was yesterday, but can't remember how I got it

  your welcome!