We will search the Forum of Windows for a 0x800co133 of answereliminate

Similar Questions

• E520 PSU / GPU level questions. (Sorry for not searching the forum I know I should have)

  EDIT: I also live in the United Kingdom

  First of all sorry for not searching the forum, I know that everyone should until they appear as far as this topic is covered a lot, but my time is short, now to the question.

  I heard rumors about wikipedia/sites that in some dell of the PSU is special for the motherboard, it is the case with this one or will an ATX normal work fine (I know it can not fit into the case which is not a concern for me)

  If the ATX is normal, can someone recommend me some what they saw was successfully used in the E520.

  Another issue is a Geforce 9500gt would work on the Rails of a 18, 305 w in the present or not, I read around that, he has only 18 bis on the rails, but he needs minimum of 350w.
  (Planning on getting an XFX 9500gt Alpha Dog Edition)

  If more information is needed to ask me any questions, I will tell you.
  I'm fine with the pc, I wanted to just a few inside the information from you guys during this forum, thank you for any help I receive, and again, I am sorry that I have not used the search tool. Cordially thanks Danny.

  Original specifications are:
  256 GB HARD DRIVE
  2 x 512 ram
  combo dvd/CD-rw drive
  ATI x 1300 pro

  I've got here now:
  3 x 256 GB HDD

  2 ram slot 512 *.
  1 slot 1 GB ram *.
  ATI x 1300 pro
  WiFi card (will not need more)

  (* I don't know if necessary ram clock speed I know with cpu - z)
  (I switched the cd/dvd for another drive hard because I didn't want to dig another sata cable)

  Message edited by SpikeTheSpiker on 01/10/2008 17:34
  
  

• I had hearing for 2 years.  Today, it crashed.  He made a mistake of configuration: 16 the message said to uninstall and reinstall.  Yes, I did.  Still the same error.  Then, I searched the forum and checked the two folder permissions.  They were right. 

  I had hearing for 2 years.  Today, it crashed.  He made a mistake of configuration: 16 the message said to uninstall and reinstall.  Yes, I did.  Still the same error.  Then, I searched the forum and checked the two folder permissions.  They were right.  Then what should I do?

  Hi Charles,

  Please see the following help on the problem article.

  https://helpx.Adobe.com/x-productkb/policy-pricing/configuration-error-CS5.html

  I hope this helps.

  Kind regards

  Sumit Singh

• Searching the Forum does not

  When I try to search the forums for help with a search form, I get the following message:
  
  The web site, you access has met an unexpected error.
  Please contact the site administrator.
  
  The following information is for the creation of Web sites for debugging purposes.
  Error occurred while processing request
  Variable FTVAR_RESULTTYPE is not defined.
  
  Resources:
  
  * Enable robust Exception information to provide more details about the source of errors. In the administrator, click debugging & Logging > Debug Output Settings, and select the robust exception information option.
  * See the ColdFusion documentation to verify that you are using the correct syntax.
  * Search the Knowledge Base to find a solution to your problem.
  
  Browser Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; RV:1.9.0.5 Gecko/2008120122 Firefox/3.0.5)
  Remote address 10.172.32.23
  Sponsor http://www.adobe.com/cfusion/webforums/forum/categories.cfm?forumid=12 & catid = 189 & entercat = y
  Date/time January 16 09 09:54

  Yes - try using Google to search for.

  http://groups.Google.com/advanced_search?q=+group:Macromedia.Dreamweaver

  The authorities are aware of this problem...

  --
  Murray - ICQ 71997575
  Adobe Community Expert
  (If you * MUST * write me, don't don't LAUGH when you do!)
  ==================
  http://www.projectseven.com/go - DW FAQs, tutorials & resources
  http://www.dwfaq.com - DW FAQs, tutorials & resources
  ==================

  "wrecks" wrote in message
  News:gkqhpf$6SF$1@forums. Macromedia.com...
  > When I try to search the forums for help with a search form, I get the
  > suite
  > message:
  >
  > The web site, you access has experienced an unexpected error.
  > Contact the administrator of the site.
  >
  > The following information is intended for developers of Web site for debugging
  > purposes.
  > Error Occurred While Processing request
  > Variable FTVAR_RESULTTYPE is not defined.
  >
  > Resources:
  >
  > * Enable robust Exception information to provide more details on
  > the
  > source of errors. In the administrator, click debugging & logging > Debug
  > Output settings and select the robust exception information option.
  > * Check the ColdFusion documentation to verify that you use the
  > correct the syntax.
  > * Search in the Knowledge Base to find a solution to your problem.
  >
  > Browser Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; RV:1.9.0.5)
  > Gecko/2008120122 Firefox/3.0.5
  > Remote address 10.172.32.23
  > Referrer
  > http://www.adobe.com/cfusion/webforums/forum/categories.cfm?forumid=12&catid=18
  9 > & entercat = y
  > Date/time January 16 09 09:54
  >

• My network printer will display the test in Windows 7 page, but nothing else. It is a Brother MFC-440CN

  My network printer will display the test in Windows 7 page, but nothing else. It is a Brother MFC-440CN

  Hi djmatthewlee

   

  1. How is the printer connected to the network?

  2. is the printer directly connected to the Windows 7 computer?
  3. do you have the updated drivers installed for the printer?

  You can refer to the link below and use the printer troubleshooter. See if it resolves the issues -
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

   

  You can also check out the link below:
  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

   

  I hope this helps.

• I want to know: if I install windows on a drive as a d or e or f or... (not on the first partition (c :)) it will reduce the speed of Windows?)

  Hi guys

  first of all the sry for my bad eng

  I have a question, please help me to find my answer:

  If I install windows on a drive as a d or e or f or... (not on the first partition (c :)) it will reduce the speed of Windows?)

  Windows speed I mean:

  Slow down the system, and run programs or...

  TNX a lot

  No, install on a partition does not affect the performance of the drive system (C:\)

• It would be possible to change the license of windows for mac license. I have CS6.

  Hello, I bought Adobe Creative Suite 6 Design and Web Premium for Windows. However, I would like to buy an IMac, and I would like to learn if it is possible here to change the license of windows for mac license. Thanks for responding.

  Yes, product order | Platform, language swap

• Upload photos to the photo gallery Windows for web sites - can't find them - I have searched for the location of the data.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem
  Hello
   
  1. don't edit you photos by chance?
  2 have you installed third-party photo editing software?
   
  Your question does contain all the required information necessary for us to help you. Please re - write your question, this time make sure you have all the information necessary and we will try to help.
   
  See: http://support.microsoft.com/kb/555375
   
  See also:
   
  Windows Photo Gallery: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Photo-Gallery-frequently-asked-questions
   
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Hi, I searched the forums, but the site has not found an answer... How to "disable another computer" for lightroom 6 (not the version of cloud).

  Hi, I keep getting the message that I've exceeded the number of computers permit.

  Now, I disable lightroom on another computer... How do I do that?

  I asked the same question in the forum search... but has not obtained a great success in return...

  Thanks Michel

  Serial number and activation support (non - CC) https://forums.adobe.com/thread/2041990 to adjust the number of activations

  If the cat person sends you back to this open forum, you are out of luck... only Adobe can help, nobody here can access the activation server

• How do you search the forum for your tech problem?

  Hello. How can I find messages on the issue of tech I have? I don't see a search feature.

  There is a search box in the upper right corner of every page of the forum (it is on Chrome and firefox, anyway).

• Errors of the desktop of Windows for gamming Manager?

  the Director of office-error constantly when I am playing games, windows aero color scheme, then the Office goes to the default colors and let the taskbar a light blue color, as well as the games I want to play don't work at all. they try and errors of load popup and nothing, even if I try to run them in compatibility mode for older operating systems that they won't stop, I even reinstalled and still nothing, completely updated windows 7 Professional 64-bit and it does on recent games, supreme commander forces and ships of war 3 and sometimes with battlefield bad compnay expansion, 2 , so please let me know what I can do to help stop or fix this isue, I'm just confused, he ran the games until the updtaes came out very well, and then he started to do this and no matter what I try and do it now, it was just the same , 2 other people I know have the same problem, so please let me know.

  Hi Chrisbible,

  Games that try to change the resolution of the screen could look for the resolution that is not supported by the display driver or monitor.

  However, to refine computer at boot startup and check if the issue still persists. Link below will help you to start the computer in clean boot: http://support.microsoft.com/kb/929135

  If the problem does not persist, you can continue with step 2 from the link above.

  Make sure that you reset the computer in step 7 normal once the troubleshooting steps are comlpete.

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• After you install the updates of windows for Vista home edition, the computer tries to restart and then says "computer could not start", then begins to the Startup Repair. Suggestions, how can I fix?

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Hello

  Welcome to the community of Windows Vista answers.

  First of all, we will try if we can start in safe mode.

  Safe mode starts Windows with a limited set of files and drivers. Startup programs do not work in safe mode, and only the basic drivers needed to start Windows are installed.

  Steps to start your computer in safe mode with networking
  1. to start mode safe mode with networking, restart the computer and press the F8 key for about four to five times. You will see "Safe Mode with network" listed in the advanced options of Windows.

  2. Select "Safe Mode with network" and then press ENTER.

  Access the link below for more information on how to start in "Safe Mode with Networking":
  http://windowshelp.Microsoft.com/Windows/en-us/help/323ef48f-7b93-4079-a48a-5c58eec904a11033.mspx

  The system restore.
  http://support.Microsoft.com/kb/936212

  Method 1:
  The restore of the system of Windows Recovery Environment (WinRE)

  (a) Insert Vista DVD and boot from the DVD.

  (b) that you want to start the computer from the Windows Vista DVD, you press a key, your keyboard when you see the prompt. You should now see a black screen with a white status bar at the bottom indicating that Windows is loading files... After some time, the status bar becomes completely white and you will see a screen indicating that Windows is loading. The environment of the installation of Windows continues to load and when finished you will be presented with a screen that prompts you for information about your location and language.

  (c) in this screen, you must configure the language to install, time and currency format and keyboard or options for method of entry so that they are well positioned. When done, press the next button. You will now be at the main Windows Vista Setup screen where you would normally install Vista on a computer.

  (d) because we want to repair the computer, you must click on repair your computer option. This will bring you to a new screen where the repair process get all facilities of Windows Vista on your computer. When finished, you will be presented with the System Recovery Options dialog box

  (e) select the Vista installation you want to repair.

  (f) in the system recovery options, click on system restore to restore the system.

  Method 2:

  Run the disk check Windows recovery environment to correct the bad sector on your hard drive

  (a) Insert Vista DVD and boot from the DVD.

  (b) that you want to start the computer from the Windows Vista DVD, you press a key, your keyboard when you see the prompt. You should now see a black screen with a white status bar at the bottom indicating that Windows is loading files... After some time, the status bar becomes completely white and you will see a screen indicating that Windows is loading. The environment of the installation of Windows continues to load and when finished you will be presented with a screen that prompts you for information about your location and language.

  (c) in this screen, you must configure the language to install, time and currency format and keyboard or options for method of entry so that they are well positioned. When done, press the next button. You will now be at the main Windows Vista Setup screen where you would normally install Vista on a computer.

  (d) because we want to repair the computer, you must click on repair your computer option. This will bring you to a new screen where the repair process get all facilities of Windows Vista on your computer. When finished, you will be presented with the System Recovery Options dialog box

  (e) select the Vista installation you want to repair

  (f) in the system recovery options, select command line and enter the command chkdsk/r.

  For the above two steps, you can see the link below.
  http://windowshelp.Microsoft.com/Windows/en-us/help/95b4c03a-ac42-49a4-a90d-8f3736a995271033.mspx

  Once you perform the restoration of the system, download the updates and install them manually one by one, this should help you knowing what update causes this problem.
   
  Concerning
  Amrihta.

• How to reset the taskbar preview window for Excel 2010?

  Hello

  My taskbar do not display all my Excel workbooks in the form of individual windows when I hover over the button. It's annoying because it makes it more difficult to pass from one to the other. This happens when workbooks are open in different instances of excel. "Show all windows in the taskbar" is checked in the Excel options. I searched internet but cannot find an answer to this question.

  I also noticed that the preview for Windows Media Player window is the play/pause and another aymore buttons. I think that the issues are linked.

  These questions appeared at the same time and after that I got a malware that took me a while to get rid of.

  I'm not an expert but have above average computer litteracy.

  Thank you for your help.

  Hello Julian,.

  Thank you for the update.

  Please, don't worry about creating another account user has administrator rights. I will help you to create and transfer the data from the old to the new account with the appropriate advice.

  First of all, let's create a new user account. Please follow the steps below:

  To create a user account

  1. To open user accounts, click the Start button , click Control Panel, click user accounts and control of Securityand then click user accounts .

  2. Click Manage another account. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. Click on create a new account.

  4. Type the name you want to assign to the user account, click an account type (select Administrator), and then click create an account.

  Once you have created the new user account with administrator rights, you can follow the steps below to transfer the data from the old to the new user account.

  a. then you are connected to the new user account and the office, press Windows key + E to open two Windows File Explorer (do this twice to open two Windows Explorer).

  b. drag one window in the left corner (edge of the monitor) and drop it. Now, the file Explorer window should take half of the screen. Do the same with another file Explorer, then drag and drop it in the upper right of the screen.

  c. Once you have two windows, half of the screen to each catch (left and right), choose one of the window (either left or a right) to access the data you want to move them to a new or previously created folder the folder. Let's say you do this from the left window.

  d d.. now in the right window, create a new folder navigation on the location where you want this folder in one place. To create a new folder, go to the location (desktop, documents, downloads where you want to save) and right click on an empty area, and then click create a new folder. Name the folder, and then click OK. Double-click the new folder that you created which should be empty.

  e. now since the window on the left, drag the data from the folder you want to move to the new folder (in the right window) and drop it.

  Note: You can also copy the data from the left window and paste into law, however, data will be duplicated until you remove them from the left window after pasting in the right.

  Do this for all the data you want to move to the new folder that you created. Once you have moved all the pictures, you can remove empty folders from the left window or delete the old account user completely.

  Well want to try the above first and let us know, we will be happy to help you further.

• Using the space map window for my project

  Dear Sir.

  I am Sundeep Neupane of the Nepal. I am currently the Bsc Hons in computer science from the Islington College affiliated with the London Metropolitan University. I am currently the research space map window, which has the ability to improve the security of the user's identity. The number of digital identities that individuals and organizations must manage increasing quickly, and good management of these identities is essential to ensure safety in the communities and markets online.

   

  My research is intended to focus on management identity associated Web mash up security by exploring and application design that takes in charge the approach centred on the user for the digital ID management. With the help of card space, many dangers, complications, trouble and uncertainty of today's online experiences can be a thing of the past. Widespread deployment of the identity metasystem has the potential to solve many of these issues, benefiting everyone and accelerating the growth of connectivity by making long term everyone online safer, more reliable and easier to use

  I have studied several newspaper, articles and whitepapers and traversed several official Microsoft page. Data was collected and the results of my research will be used to finish my final year project. So I might be able to use the space map window as part of my final year project. This study will be used for academic purposes and will be the cornerstone of my final year project.  This final year project is expected to publish a valid contribution academically and the Nepalese General.

  Do not hesitate to contact me

  Thank you very much

  Yours truly,

  Sundeep Neupane

   

  Hi Nathalie,.

  Please contact Microsoft Community.

  I understand that you want to use Windows Card Space for your final year project.

  I suggest you post the query on the MSDN forum, because we have experts working on these issues.

  You can check the link to post the same query on MSDN

  https://social.msdn.Microsoft.com/forums/en-us/home?Forum=windowscardspace&filter=AllTypes&sort=lastpostdesc

  For more information about the Windows card space, refer to the article below:

  http://msdn.Microsoft.com/en-us/library/aa480189.aspx

  Hope this helps, I wish you all the best for your final year project.

  Get back to us if you need further assistance for Windows.

• Add the UNC path to search the index in Windows 7

  I have a desktop running Windows 7 (commercial version).  I want to add some UNC paths in the search to allow Windows to search index to locate files on mapped network drives.

  My network mapped drives from Windows Home Server that is running Windows Search 4.0.

  I am running Windows Search 4.0 on a (separate) computer at work and I saw a tab in Indexing Options to allow the addition of UNC paths.  Unfortunately, it seems that the search built into Windows 7 version does not UNC paths to be added.

  I saw solutions to this problem that involve UNC paths mapping local drives with the help of a symbolic link, but I don't want to do that.  Readers are already mapped and work just fine.  There must be a way to update the research on Windows 7 or otherwise activate adding of UNC paths?  It doesn't seem to be a downloadable installer for Windows Search 4.0 for Windows 7.

  Note: I just saw the Windows Desktop Search add-in for Microsoft Networks (http://www.microsoft.com/downloads/details.aspx?FamilyID=f7e981d9-5a3b-4872-a07e-220761e27283&displaylang=en) files.  I will install that, but shouldn't it already be part of the search Windows on Windows 7?  Why do I need a complement of 2008 to allow something on a whole new operating system which is already present in versions of research working on older operating systems (XP, 2003 Server)?

  I noticed several answers to select 'Always available offline' which copies the files to the local hard disk.  It is an unacceptable answer as my business system cannot be copied onto my hard drive.

  Microsoft used to have the ability to add a network drive to the list of search/index.  It is a huge hole missing in the search for Windows 7.  I'll have to look at Google search of as an alternative if it manages the network drives.