Weird appears after the breakdowns during the resynchronization
So I'm currently resynchronize my SIN after a replacement drive. Everything worked fine but this morning, we had a failure for fifteen minutes, and when the power came back I went down and powered the NAS again. Got the "boot" on the screen, and then he delivered showing...
'blk_rq_map_sg + 418'
It just sits there, I can't connect to it, button / stop does not.
There are inside red 4x4TB WD drives, and one of them was replaced yesterday to move errors, so the SIN has been currently synchronize at the time of the failures.
Someone had this message on the front screen?
Well, I decided to remove the power. Put the cable back in and it started, have passed "Booting... '. "and now says"Recover data XX. XX %"so I cross my fingers it was just a single strange thing.
Tags: Netgear
Similar Questions
-
disruptive ads appearing after the operation of key or mouse
How can I stop disruptive ads appearing after the mouse operations or key
Thank you, I'll try that
-
White loading bar appears after the splash screen. TAKES FOREVER TO FILL!
I recently formatted my windows xp because it was slowing down. I do this once a year and its good because my newly formatted computer takes 30 sec or less to load. However this time I formatted, after the screen intel and BIOS, a black scren appears for 1 minute, then an alternating black and white bar appears at the bottom. no text, nothing. This bar fills up until halfway, then the "xp" logo appears and the computer loads normally. the problem is that the loading bar takes 7 min + join to halfway. so my newly formatted computer load in 8-9 minutes rather than 30 seconds like its supposed to!
I tried to reformat, reinstall xp, but the same thing is happening: s
Once the computer loads however, everything works fine. It's just takes TOO long!Hi MontyPanesar,
Thanks for posting. Please, try the following.
1. place your Windows XP installation CD and start to her...
2. Press any button to start the Windows installation (don't worry... we do not actually use the installer at this point)
3. wait a few moments for the installation program starts, when you see repair an installation of Windows XP using the Recovery Console, and then press the R key
4. wait until you see this screen, enter the number of your master installation. (Typically 1 to C:\Windows)
5. press ENTER.
6. If you are prompted to do so, enter your administrator password. If you don't have one, leave the field blank and press to enter.
7. from the command prompt, type: chkdsk/r (note the space between chkdsk and / r)
Allow it to complete undisturbed.
8. remove the disc, then restart.I hope this helps! Shawn - Support Engineer - MCP, MCDST
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think -
The DV6-6117dx model (as well as other HP Pavilion laptops) have experienced a problem where the screen will display a flickering, horizontal line to the top of the screen, after it has been automatically disabled (note: not in sleep or Standby Mode).
There is a setting to "off the display of [X] minutes" in power options. I have my DV6-6117dx value dim the screen after 10 minutes and turn it off after 15 minutes of inactivity. Sometimes, but not always, when I move the mouse to turn the screen back on, a couple of flickering horizontal lines will appear at the top of the screen. It is very annoying, and the only way to remove them and to have the screen back to normal is one.) put the computer to sleep and wake it or b.) restart the entire system.
Everything by putting the laptop to sleep and wake-up is not a huge problem, I wouldn't do that, period. I owned a laptop Toshiba for about 6 years and never had a problem with her like this (the reason why I bought a new laptop was because my old man was 6 years old and the technology was outdated a lot, a lot).
HP says it's a software problem, but it did come with a way to fix it yet (at least not that I've found). I ask all the 'Experts' out there if they have a final way to solve this common issue experienced by some models of HP laptops? I said to uninstall and reinstall video drivers without success. I said to install video drivers only to AMD, and then only to HP, and then only from Windows Update, but none of these solutions worked. I said to update BIOS, but it does not solve the problem. I told him to try to restore the system to the factory settings, but this did not help. It is obviously a software problem, but nobody at HP seems to have a definitive solution, how to fix it. Is my only hope to return to my laptop to be replaced by a different model entirely?
I hope that someone out there has an answer, it's a common issue that I know a lot of owners of portable HP experienced. Thank you!
Hello
I think it's the right time to get in touch with HP and use the guarantee. How to do?
Click on the link below and choose your country:
Contact HP worldwideYou can also try the suggestions from the link below before you send it to the service:
-
March 23 windows set to date. a failure and then managed. After that, the compaq screen has changed and the blue display lights for a little after the Welcome screen.
Hello
If you think the update caused the blue screen then uninstall it to check.
Control Panel - Windows Updates - lower left Installed Updates - uninstall or change
Or
Remove an update
http://windowshelp.Microsoft.com/Windows/en-us/help/182043da-fc3e-4220-AFBC-d9b09f2b2a1a1033.mspxOr
The problems with the removal of updates
http://windowshelp.Microsoft.com/Windows/en-us/help/5a319824-5cb5-493d-9151-9a97d0f565b61033.mspx
OrHow to uninstall updates in Windows Vista
http://www.vista4beginners.com/how-to-uninstall-Windows-Vista-updatesDisable or hide optional updates on Windows Vista
http://www.howtogeek.com/HOWTO/Windows-Vista/disable-or-hide-optional-updates-on-Windows-Vista/==============================================================
If not, remove the updates help then we can troubleshoot the BlueScreens.
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
(also Windows 7)
http://www.winvistatips.com/disable-automatic-restart-T84.html===========================================================
Check out these utilities to see if information may be collected:
It is an excellent tool for displaying the blue screen error information
-Free - BlueScreenView scans all your minidump files created during "blue screen of death," collisions
and displays information about all accidents of a table.
http://www.NirSoft.NET/utils/blue_screen_view.html-------------
MyEventViewer can be verified at the time of the blue screen (BSOD) within a second or so of the
time of the BSOD to provide more information about the possible cause - see TIP.MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
Set it for a bit before and after the time of the BSOD.
http://www.NirSoft.NET/utils/my_event_viewer.html------------
AppCrashView - free - a small utility for Windows Vista and Windows 7 that displays the details of all the
application goes down has occurred in your system. The information breaks down is extracted from the .wer
the files created by the Windows Error Reporting (WER) of the operating system component of each
time that an accident has occurred. AppCrashView also allows you to easily record the list of accidents to
text/html/csv/xml file.
http://www.NirSoft.NET/utils/app_crash_view.htmlI hope this helps.
-
I use FF8 with Selenium RC test infrastructure. When I installed the last update of FF contextual dialog YesNo "You want to contribute to improve..." ' began to appear before each test is run. Thus, the test stopped running on this popup and my problem is that I can not disable this popup for next time. I want to say I select Yes or no, popup disappears, but still appears in the next round of tests. How can I disable this popup at all?
Hi guys! Thanks to all of you for the cooperation and ready to help. I have summarized all your advice, so the following 3 steps unravel the problem for FF8 and do my tests to run fine:
- Create and configure a new FF profile, using these instructions and suggestions . Don't put your FF to the default profile at the end.
- Then follow the first 6 steps by SafeBrowser (see above) to the new profile. Switch to the default profile (in firefox - p).
- Don't forget to use your new profile when you run the selenium Server (-firefoxProfileTemplate command line parameter) or the value of selenium to use this profile when starting a browser to Salenece.
-
Shortcuts do not work and open with box appears after the virus
None of my shortcuts work, a box to choose which program you want to use to open this always appears. The only way to open a program is to right click and select the administrator rights.
Had a problem with a virus, it has been removed with norton 360, none of my programs won't work if you right click and choose Run as administrator. Can someone help me solve this problem? Thank you very much
Had a problem with a virus, it has been removed with norton 360, none of my programs won't work if you right click and choose Run as administrator. Can someone help me solve this problem? Thank you very much
See if this tutorial will help. It helps you to rebuild the icon cache that could have been corrupted.
http://www.Vistax64.com/tutorials/117229-icon-cache-rebuild.htmlt-4-2
-
I can not connect my phone because I forgot my administrator / power on password. 53427575 appears after a few failed attempts. Can you give me a code please?
Try to time.
42585571
REO
I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.
-
Kaspersky sign appears after the full system restore
After that I did a restore of the entire system on my computer, I have a sign indicating "kaspersky is not lit." What does that mean? This means that my computer came pre-installed with a free trial of kaspersky?
Hello
Computers are normally with a free trial of an Antivirus for many days.
It is normally Norton or McAfee.
You must configure the free trial. A system recovery reinstalls the operating system to exactly how you bought your computer.
If the trial was initially, it will appear again after doing a restore to factory settings
Consult the manual of your computer as to what had been bought...
See you soon.
-
Mice are not appearing after the last update of Windows 8
After update to the last version of windows 8, my mouse does not work on my computer no more. I use a "HAMA Optical Mouse AM-5000" and a 64-bit Windows 8 operating system to my office. Before the update, everything worked very well, but a little at the time (perhaps a week?) there was a software update that began when I shut down my computer for the night and after, my mouse wouldn't just appear. Then I want to restore my computer to before the update and everything would work fine. It happened maybe 3 times in the past week. Today, however, every time that I restored it to an earlier date, the mouse still does not. I tried the following things:
Deactivation and reactivation of the mouseUninstall the drivers and search for updatesTry different mouse (2 USB, 1 green connector)Using the troubleshooting in the Device Manager tool, a fine of the questionNon of them did it no matter what and I wonder if I'm the only one to receive the problem. and what I can do about it. Trying to navigate in windows using only the keyboard becomes very annoying XD.Thanks for the reply of Kevin,In the (Control Panel > system and security > Windows Update > View Update History) all there is "you have not tried to install the updates for this computer. There "18 updated important and 5 available optional updates to install, but I think that those who might be updates that have been the cause.
In the (Control Panel > programs > programs and features > Installed Updates) there are a bunch of installed updates. The most recent is "Word Viewer 2003 Service Pack 3 (SP3): WDVIEWSP3" which has been installed on 26/09/13 and "update for Microsoft Windows (KB2889543)" which has been installed on 25/09/13.I downloaded the latest drivers from the mouse on the site that you have linked and no change. By chipset are you referring to the processor (Intel i7)? -
An error appears after the rule of matadata Execute running
Hi Expert
I'm tring to load the data of the EBS GL to HFM (11.1.2.3). After I chreated four matadata rules account, entity, Custom1 and Custom2 in feature sets of metadata, I try to click the Execute button to execute these rules. Error below. Do you have any experience with this?
2014-04-23 22:07:42, 699 FATAL [AIF]: error of COMM LKM support members in HFM - metadata support to HFM
Traceback (most recent call changed):
File '< string >", line 346, in loadMembers
ODIHAppException: com.hyperion.odi.common.ODIHAppException: [SERVER] properties are required.
The mistake of studio ODI as below:
Failed session: 63501: ODI-1217: COMM_LOAD_MEMBERS_TO_HFM Session (63501) fails with return code 7000.
ODI-1226: COMM members in HFM load step fails after 1 attempt.
ODI-1240: flow COMM support members in HFM fails during an operation of integration. This flow of charge target table target modeling.
Caused by: org.apache.bsf.BSFException: exception of Jython:
Traceback (most recent call changed):
File "< string >", line 27, < module >
File '< string >", line 346, in loadMembers
at com.hyperion.odi.hfm.ODIHFMAppWriter.beginLoad(ODIHFMAppWriter.java:161)
at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)com.hyperion.odi.common.ODIHAppException: com.hyperion.odi.common.ODIHAppException: [SERVER] properties are required.
at org.apache.bsf.engines.jython.JythonEngine.exec(JythonEngine.java:146)
at com.sunopsis.dwg.codeinterpretor.SnpScriptingInterpretor.execInBSFEngine(SnpScriptingInterpretor.java:322)
at com.sunopsis.dwg.codeinterpretor.SnpScriptingInterpretor.exec(SnpScriptingInterpretor.java:170)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.scripting(SnpSessTaskSql.java:2473)
at oracle.odi.runtime.agent.execution.cmd.ScriptingExecutor.execute(ScriptingExecutor.java:48)
at oracle.odi.runtime.agent.execution.cmd.ScriptingExecutor.execute(ScriptingExecutor.java:1)
at oracle.odi.runtime.agent.execution.TaskExecutionHandler.handleTask(TaskExecutionHandler.java:50)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.processTask(SnpSessTaskSql.java:2913)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java:2625)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatAttachedTasks(SnpSessStep.java:580)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java:468)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:2128)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:1931)
to oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$ 2.doAction(StartScenRequestProcessor.java:580)
at oracle.odi.core.persistence.dwgobject.DwgObjectTemplate.execute(DwgObjectTemplate.java:216)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor.doProcessStartScenTask(StartScenRequestProcessor.java:513)
to oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$ StartScenTask.doExecute (StartScenRequestProcessor.java:1073)
at oracle.odi.runtime.agent.processor.task.AgentTask.execute(AgentTask.java:126)
to oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor$ 1.run(DefaultAgentTaskExecutor.java:50)
at org.springframework.core.task.SyncTaskExecutor.execute(SyncTaskExecutor.java:50)
at oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor.executeAgentTask(DefaultAgentTaskExecutor.java:41)
at oracle.odi.runtime.agent.processor.TaskExecutorAgentRequestProcessor.doExecuteAgentTask(TaskExecutorAgentRequestProcessor.java:93)
at oracle.odi.runtime.agent.processor.TaskExecutorAgentRequestProcessor.process(TaskExecutorAgentRequestProcessor.java:83)
at oracle.odi.runtime.agent.support.DefaultRuntimeAgent.execute(DefaultRuntimeAgent.java:68)
at oracle.odi.runtime.agent.servlet.AgentServlet.processRequest(AgentServlet.java:562)
at oracle.odi.runtime.agent.servlet.AgentServlet.doPost(AgentServlet.java:516)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:727)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:821)
to weblogic.servlet.internal.StubSecurityHelper$ ServletServiceAction.run (StubSecurityHelper.java:227)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)
at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:27)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
to oracle.security.jps.ee.http.JpsAbsFilter$ 1.run(JpsAbsFilter.java:119)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:163)
to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.run (WebAppServletContext.java:3696)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1490)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)
Caused by: Traceback (most recent call changed):
File "< string >", line 27, < module >
File '< string >", line 346, in loadMembers
at com.hyperion.odi.hfm.ODIHFMAppWriter.beginLoad(ODIHFMAppWriter.java:161)
at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)com.hyperion.odi.common.ODIHAppException: com.hyperion.odi.common.ODIHAppException: [SERVER] properties are required.
at org.python.core.PyException.fillInStackTrace(PyException.java:70)
at java.lang.Throwable. < init > (Throwable.java:181)
at java.lang.Exception. < init > (Exception.java:29)
to java.lang.RuntimeException. < init > (RuntimeException.java:32)
to org.python.core.PyException. < init > (PyException.java:46)
at org.python.core.PyException.doRaise(PyException.java:200)
at org.python.core.Py.makeException(Py.java:1166)
at org.python.core.Py.makeException(Py.java:1170)
at org.python.core.Py.makeException(Py.java:1174)
at org.python.core.Py.makeException(Py.java:1178)
to $2 org.python.pycode._pyx403.loadMembers (< string >: 414)
to org.python.pycode._pyx403.call_function (< string >)
at org.python.core.PyTableCode.call(PyTableCode.java:165)
at org.python.core.PyBaseCode.call(PyBaseCode.java:297)
at org.python.core.PyBaseCode.call(PyBaseCode.java:191)
at org.python.core.PyFunction.__call__(PyFunction.java:385)
at org.python.core.PyMethod.__call__(PyMethod.java:215)
at org.python.core.PyMethod.instancemethod___call__(PyMethod.java:221)
at org.python.core.PyMethod.__call__(PyMethod.java:206)
at org.python.core.PyObject.__call__(PyObject.java:367)
at org.python.core.PyObject.__call__(PyObject.java:371)
to org.python.pycode._pyx408.f$ 0 (< string >: 27)
to org.python.pycode._pyx408.call_function (< string >)
at org.python.core.PyTableCode.call(PyTableCode.java:165)
at org.python.core.PyCode.call(PyCode.java:18)
at org.python.core.Py.runCode(Py.java:1204)
at org.python.core.Py.exec(Py.java:1248)
at org.python.util.PythonInterpreter.exec(PythonInterpreter.java:172)
at org.apache.bsf.engines.jython.JythonEngine.exec(JythonEngine.java:144)
at com.sunopsis.dwg.codeinterpretor.SnpScriptingInterpretor.execInBSFEngine(SnpScriptingInterpretor.java:322)
at com.sunopsis.dwg.codeinterpretor.SnpScriptingInterpretor.exec(SnpScriptingInterpretor.java:170)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.scripting(SnpSessTaskSql.java:2472)
at oracle.odi.runtime.agent.execution.cmd.ScriptingExecutor.execute(ScriptingExecutor.java:47)
at oracle.odi.runtime.agent.execution.cmd.ScriptingExecutor.execute(ScriptingExecutor.java:1)
at oracle.odi.runtime.agent.execution.TaskExecutionHandler.handleTask(TaskExecutionHandler.java:50)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.processTask(SnpSessTaskSql.java:2913)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java:2625)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatAttachedTasks(SnpSessStep.java:577)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java:468)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:2128)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:1930)
to oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$ 2.doAction(StartScenRequestProcessor.java:580)
at oracle.odi.core.persistence.dwgobject.DwgObjectTemplate.execute(DwgObjectTemplate.java:216)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor.doProcessStartScenTask(StartScenRequestProcessor.java:513)
to oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$ StartScenTask.doExecute (StartScenRequestProcessor.java:1073)
at oracle.odi.runtime.agent.processor.task.AgentTask.execute(AgentTask.java:126)
to oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor$ 1.run(DefaultAgentTaskExecutor.java:49)
at org.springframework.core.task.SyncTaskExecutor.execute(SyncTaskExecutor.java:49)
at oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor.executeAgentTask(DefaultAgentTaskExecutor.java:41)
at oracle.odi.runtime.agent.processor.TaskExecutorAgentRequestProcessor.doExecuteAgentTask(TaskExecutorAgentRequestProcessor.java:92)
at oracle.odi.runtime.agent.processor.TaskExecutorAgentRequestProcessor.process(TaskExecutorAgentRequestProcessor.java:83)
at oracle.odi.runtime.agent.support.DefaultRuntimeAgent.execute(DefaultRuntimeAgent.java:68)
at oracle.odi.runtime.agent.servlet.AgentServlet.processRequest(AgentServlet.java:562)
at oracle.odi.runtime.agent.servlet.AgentServlet.doPost(AgentServlet.java:516)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:727)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
to weblogic.servlet.internal.StubSecurityHelper$ ServletServiceAction.run (StubSecurityHelper.java:227)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)
at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
to oracle.security.jps.ee.http.JpsAbsFilter$ 1.run(JpsAbsFilter.java:119)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:324)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:460)
at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:103)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:163)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.wrapRun (WebAppServletContext.java:3730)
to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.run (WebAppServletContext.java:3696)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2273)
... 4 more1. open ODI Studio Console
2. connect to your repository FDMEE
3. go to the topology
4. develop Hyperion Financial Management
5. double click on HFM_SERVER
6 enter your cluster HFM 'Cluster (data server).
7. save all
Please mark this question as useful to the answer so that others can see
Concerning
-
Old passwords appeared after the update of firefox 32
After upgrading to firefox 32 all passwords added or changed in the month of August have disappeared or returned to their previous States. But if I downgrade to the previous version all passwords are on the right place. How to solve this problem? Thank you.
You may have to go to your profile folder and delete the file logins.json (make a backup first!) then manually and try the procedure again.
-
ATA-associated message will appear after the stop of the series Qosmio G-start
Good computer worked fine, but earlier when I tried to start it it just freezes on the start QOSMIO screen and will not continue.
I can not press F8 and choose how to start and the HARD drive on the computer light remains solid. After leaving it for about 1 minute, I get the following message.
ATA ERROR #0
ERROR ATA #1
any help would be appreciated, thanks
Hello
That sounds really serious. You can try to reset the bios by default (refer to the operating manual how to do) and then try to start it again.
Otherwise, the only thing you could do is to bring the machine to a local service for a hardwarecheckup partner (or repair).
Would appreciate some comments
-
WRT54G2 problem appears after the firmware update
Hi everyone, a newbie here. Nice to meet you all and thank you in advance for your help.
Here's my problem. I have updated the firmware on my router for 1.0.04)is Sunday, and then there are problems on my router.
1 have a weaker signal.
2. the router cannot detect my internet just as it has been in the past. I have to type in my PPPoE setting for example my user name and password in 192.168.1.1. Furthermore, I use AT & T DSL.
3. my internet will totally drop off after several hours. I have to reopen it and the modem power on & off switch.
So I want to know if I can downgrade the firmware back to 1.0.01 or is there any other setting that may help me get but it? A list of steps is better.
Thanks again in advance and have a nice day.
If you haven't already done so, try to do a hard reset, hold reset button of the router for at least 30 seconds with the power connected to the router, and then reconfigure as needed.
Since I use your & AT T DSL, you can reconfigure the DSL modem, so it don't the PPPoE connection and then reconfigure Type Automatic Configuration - DHCP Internet connection router.
There is another question that may arise with an AT & T DSL modem. My Speedstream 4100 & AT T DSL modem put the IP address 192.168.1.1 for the router WAN/Internet port. If the router is configured to the default settings, there will be a conflict between the modem and the router and none of router devices connected will be able to access the internet. The solution is to change the IP Address of the router to the router on 192.168. 2.1. Restart all router connected devices after you have made this correction.
Also with some model WRT54G2 (happens on my router WRT54G2 V1) the wireless signal will go offline when a wired computer is started. When this happens, the work around is the power cycle that the router once the wired computer has started, or log in to the router, go to basic wireless settings page and click on the button Save the settings. Then the wireless signal comes back to the top and wireless devices will resume their connection.
-
How to disable the "Insert smart card" dialog box keeps appearing after the connection?
Running Windows 7 64 bit on a laptop Dell which includes and integrated smart card reader. My configuration does not require a smart card to log on. I was wondering if the smart card reader has worked, I plugged a card chip used on another system. The driver is installed automatically, so it appears the drive works.
Now, whenever I log in, the "Insert smart card" dialog box is displayed. If I cancel or close the box, he continues to reappear every few seconds. How to disable this behavior?
Update: this is somehow connected to Outlook 2003. I have 4 different e-mail accounts. The "Insert smart card" box appears only when checking for my att account (yahoo), which is configured by using POP3.
Go to the Services.msc and check the settings for the smartcard (manual test) service.
Tom
PS 29 December 2011
The position of the OP, have been reported since a lot of this problem on the some notebooks Dell and HP. There are a few reports that a replacement of the motherboard fixed the problem and the other that the relocation of a certain connector (no mention of exaclly one that) solves the problem. Direct contact with the manufacturer of the laptop computer, Dell or HP wether, might be useful. Try a follow-up if you have already made contact.
Tom
Maybe you are looking for
-
When support ends for Firefox 24 ESR, will be Australis have been removed?
At the time that Mozilla stops its support for Firefox 24, there chances of the abomination known as Australis have been removed since Firefox? It is a simple, easy to answer the question by a developer and will inform my decide whether or not I'll c
-
Re: Satellite L850: how to get the approval number?
I bought the laptop model above Satellite L850 UAE UNITED, but now I'm in Sri lanka.I had some problem with my hard drive and the system said that to replace the hard drive. While I contacted a provider in Sri Lanka and asked me to register the produ
-
How to remove the password of BIOS - 4070CDS Satellite?
Hello My wife just to get an old laptop work (Satellite 4070CDS) we want to use it as a pc for free internet access, which is just about everything for a small donation, I think that it was capable of. But bring it back, we have a problem He has a *
-
I am running XP SP3 with IE8. A / V is McAfee of ATT Uverse. I downloaded the MSRT tool and ran in safe mode. Can't find any infected files. Has not run mode normal because svchost.exe has exhausted all of the CPU resources. At 8 instances of svchost
-
How to import codes Verilog in LabVIEW FPGA?
I tried to import the Verilog code by instantiating followed education in http://digital.ni.com/public.nsf/allkb/7269557B205B1E1A86257640000910D3. but I can still see some errors when compiling the file VI. Test file simple Verilog is as follows: ===