WES610N has not managed a DHCP requests of beneficiaries to E3000?
I can not get my WES610N to transmit DHCP requests via wireless to my E3000 router.
If I connect physically E3000-> WES610N-> laptop, it'll pass the DHCP request and get network access to the laptop.
As soon as I use the WAP as provided for in my media center with Wireless between E3000-> WES610N a wired connection between WES610N-> mobile/XBOX/PS3 none of the DHCP requests are passed along, and no access to the network is provided. The wireless signal remains strong to WAP, and I show the client wireless and assigned address DHCP at the end of the router.
I am running the latest firmware to factory on the E3000 (tried DD - WRT with no luck). Wireless security is WPA2-Personal with AES and a MAC filter to allow only a list of wireless clients. Run auto-channel and connected to the 5 GHz signal. I even tried to add MAC addresses to filter for customers physically connected to WAP with no luck.
Is there something I'm missing here, or is this a common problem?
Thanks in advance for any help!
Of course, it was something simple that fixed... I had checked the firmware on the router was in effect, but for some reason any it never came to mind to check the firmware on the bridge itself.
I received a chat session with the help of Cisco and they gave me the link for the updated for the WES610N and the WET610N firmware. After a re-flash all my current configurations for network addresses, authentication and appointing remain - so all I had to do was to remove the wired connection to router at the bridge (which was required to connect and perform the flash) and give it a try.
Initially, with the bridge still sitting next to the router it would drop and re - connect about every 20 seconds, an improvement, but still not acceptable. As soon as I moved it 10 + feet away from the router (as shown) the connection remained strong and is more randomly disconnected. The final resting place has been to my media center, which is about 30 feet more far laterally and down a level in my house.
After flash it now connects quickly, successfully passes DHCP queries on multiple devices, successfully conducts tests of speed/transfer and does not abandon the connection only once during a few hours of play. The speeds are always disappointing, maxing out at about 70 MB/s on wirelessN - but that's a lot for streaming media and ~ 2 x more than my cable internet service can pull down.
Anyway, here is the link to the firmware if you are still with me after this long explanation:
Tags: Linksys Routers
Similar Questions
-
When I press on trying to download photoshop cc at 42%, it is said that he has not managed to download every time I try to download
Orbital ZiLe for more information on how to resolve errors download please see error download and installation of the creative cloud application.
-
ASA Cisco IPSEC VPN tunnel has not managed the traffic
Hi guys
I am trying to set up a new connection IPSEC VPN between a Cisco ASA 5520 (verion 8.4 (4)) and Checkpoint Firewall. I managed to establish the phases IKE and IPSEC and I can see the tunnel is UP. But I can't see any traffic through the tunnel. I checked the cryptomap both ends and try to test with a contionuous ping from within the network of the SAA.
I made a screenshot of ICMP packets but cannot see in ASA. I welcomed the icmp inside ASA interface.
I did a package tracer and it ends with a fall of vpn - filter the packets. But can not see any configured filters...
Your help is very appreciated...
Thank you
You probably need to add nat negate statements:-something like.
object-group network OBJ-LOCAL
Network 10.155.176.0 255.255.255.0
object-group network OBJ / remote
object-network 192.168.101.0 255.255.255.0
NAT static OBJ-LOCALOBJ-LOCAL source destination (indoor, outdoor) static OBJ-REMOTE OBJ-REMOTE-no-proxy-arpYou are running 8.4 nat 0 has been amortized
-
ESW-520-24 P has not managed the custom VIRTUAL local network traffic
Hi all
We recently bought a switch ESW-520-24 p to replace a CE500 end-of-life. The facility where the switch is installed has access wireless connected to the VLAN 110 points.
Course the ESW-520-24 p switch does not support VTP so none VLAN is to be propagated to it. So I created 110 VLAN manually and ports assigned to him. But the devices on ports communicate with anything.
All ports are configured as access with 110 ports VLAN not identified. The uplink is the g2 port which is in binding mode.
Can someone please tell me what I can have configured wrong?
Thank you
-Steve
Hi Steve,.
If it is for UC500 installation, the default configuration on the ESW is normally perfect and the switch has to be turned on.
Otherwise that looks like you have made the correct things.
I guess VLAN1 is always present on the ESW switch, but excluded by access ports...
All ports are not marked in VLAN110 except for the uplink, given that the packages of vlan tagged while waiting to switch receiver VLAN110 or unmarked packages? (something to think quickly)
But the result is if you are still in a stalemate, why not call the Small Business Support Center, the switch is probably still under warranty and telephone support.
http://www.Cisco.com/en/us/support/tsd_cisco_small_business_support_center_contacts.html
Best regards, Dave
-
IPN has not managed the traffic
I deployed an IPN for the VPN user contributions posture. Right now I have no control of posture enabled and I leave with a past "all permit" list DACL, but I can not pass traffic (no ping from the VPN client to an internal resource).
For the heck of it I put a subnet filter for my VPN hen on the IPN and then I get ping, while it makes me think the routing is all good, must be the right of the IPN?
Any ideas?
Thank you!
The IPN can you issue a "session of pep show table? You should see the ip address of the client. If jot check tunnel group to see if the accounting server group and the Group of authentication servers point to the node of the ipn. Also, make sure that you hit the permission node online profile.
Sent by Cisco Support technique Android app
-
SQL query problem - (internal has not managed to the outer query)
Hi all:
Here is my SQL query:
Why am I the overall percentage of all Sites as opposed to each percentage calculation for each site. I've grouped by Rd. SITE, so I assume he would calculate the percentages for each site. What I've done wrong?SELECT RD.SITE, ROUND( (SELECT COUNT (DISTINCT PB.EMP_ID) FROM BOOK PB WHERE PB.EMP_ID IN (SELECT PB.EMP_ID FROM BOOK PB ) ) / (SELECT COUNT (DISTINCT PB.EMP_ID) FROM BOOK PB WHERE PB.EMP_ID IN (SELECT PB.EMP_ID FROM BOOK PB WHERE MO.QUALIFIER > 4 ) )* 100, 2) AS PERCENTAGE FROM BOOK PB LEFT JOIN POSITION MO ON PB.EMP_ID = PO.EMP_ID INNER JOIN PHYS_LOCATION RD ON MO.HOUSED = RD.SITE_ID WHERE MO.ACTUAL_END IS NULL GROUP BY RD.SITE;
Thank you for your help.AquaNX4 wrote:
Hi all:Here is my SQL query:
SELECT RD.SITE, ROUND( (SELECT COUNT (DISTINCT PB.EMP_ID) FROM BOOK PB WHERE PB.EMP_ID IN (SELECT PB.EMP_ID FROM BOOK PB ) ) / (SELECT COUNT (DISTINCT PB.EMP_ID) FROM BOOK PB WHERE PB.EMP_ID IN (SELECT PB.EMP_ID FROM BOOK PB WHERE MO.QUALIFIER > 4 ) )* 100, 2) AS PERCENTAGE FROM BOOK PB LEFT JOIN POSITION MO ON PB.EMP_ID = PO.EMP_ID INNER JOIN PHYS_LOCATION RD ON MO.HOUSED = RD.SITE_ID WHERE MO.ACTUAL_END IS NULL GROUP BY RD.SITE;
Why am I the overall percentage of all Sites as opposed to each percentage calculation for each site. I've grouped by Rd. SITE, so I assume he would calculate the percentages for each site. What I've done wrong?
It's what you're asking. Your subquery scalar to get the percentage is not restricted by the current site. Add columns to filter to restrict the values selected for the calculation
Published by: riedelme on May 8, 2013 07:26
-
SPA3102 CID has not managed to asterisk
Hello
I have several 3102 to FXO line with asterisk integration.
The only thing that I was unable to make it work, even with the option:
PSTN to VoIP CID CID: Yes
Was to the CID go to the asterisk, if I check the info on 3102 tab, in last PSTN Caller:, I can see the last number of the caller.
I have what would be missing?
Thanks in advance,
Jorge Bastos,It seems that "yours" RTC gives CID information between the first and second ring. Currently, PROMPTS for Asterisk is sent immediately, for example before the CID is known. It must be delayed until the CID is available.
Go to the section "FXO Timer values".
The "PSTN Answer Delay" value number (in seconds) which is a little more than sound period on your PSTN line. Period of ring is about 5 second in most countries. so, I recommend that you use 7 seconds here in this case.
-
Hello
I am to evaluate a tool that allows you to migrate a database from MySQL to oracle. Everything seems fine, until the tool is gone through the import of the target Oracle database process. The following error arises: ORA-12520: TNS:listener could not find a Manager is available for the requested server type
Following is part of the output of the migration, just tool before and where the error occurs:
---
...
Connected to:
Oracle Database 10g Express Edition Release 10.2.0.1.0 - Production
SWS_core_documentation_ID SEQUENCE of FALL
*+
ERROR on line 1:
ORA-02289: sequence does not exist
Order of creation.
Trigger created.
Disconnected from Oracle Database 10g Express Edition Release 10.2.0.1.0 - Production
Core_group for Oracle table import
Creating table and its constraints using the Oracle SQL * more utilitarian
SQL * more: Release 10.2.0.1.0 - Production kills Mar 31 16:20:14 2009
Copyright (c) 1982, 2005, Oracle. All rights reserved.
ERROR:
ORA-12520: TNS:listener could not find Manager available for requested type
Server
Enter user name:
---
I searched around and raised that potentially the problem could lie with the MAX_UTILIZATION value for the number of PROCESSES. How can I increase the value?
Some diagnoses are:
---
+ $> lsnrctl services +.
LSNRCTL for 32-bit Windows: Version 10.2.0.1.0 - Production on March 31, 2009 16:37:44
Copyright (c) 1991, 2005, Oracle. All rights reserved.
Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = EXTPROC_FOR_XE)))
Summary of services...
Service 'CLRExtProc' has 1 instance (s).
Instance of 'CLRExtProc', status UNKNOWN, has 1 operation for this service...
Managers:
+ 'DEDICATED' set up: 0 denied: 0 +.
LOCAL SERVER
Service 'PLSExtProc' has 1 instance (s).
Instance of 'PLSExtProc', status UNKNOWN, has 1 operation for this service...
Managers:
+ 'DEDICATED' set up: 0 denied: 0 +.
LOCAL SERVER
Service 'XEXDB' has 1 instance (s).
Instance "xe", State LOAN, has 1 operation for this service...
Managers:
+ "D000" put in place: 0 denied: 0 current: 0 max: 1002 State: loan +.
DISPATCHER < machine: xxxxxxx, pid: 2552 >
+ (Address = (Protocol = TCP (port = 1044))(Host=xxxxxxx)) +.
Service 'XE_XPT' has 1 instance (s).
Instance "xe", State LOAN, has 1 operation for this service...
Managers:
+ 'DEDICATED' set up: 38 refused: 0 status: ready +.
LOCAL SERVER
"Xe" service has 1 instance (s).
Instance "xe", State LOAN, has 1 operation for this service...
Managers:
+ 'DEDICATED' set up: 38 refused: 0 status: ready +.
LOCAL SERVER
The command completed successfully
+ $> +.
---
+ $> lsnrctl status +.
LSNRCTL for 32-bit Windows: Version 10.2.0.1.0 - Production on March 31, 2009 16:51:52
Copyright (c) 1991, 2005, Oracle. All rights reserved.
Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = EXTPROC_FOR_XE)))
STATUS of the LISTENER
------------------------
Alias LISTENER
Version TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
Beginning of March 31, 2009 15:58:13
Uptime 0 days 0 h 53 min 38 s
Draw level off
Security ON: OS Local Authentication
SNMP OFF
Default Service XE
Listener parameter File C:\oraclexe\app\oracle\product\10.2.0\server\network\admin\listener.ora
Listener log file C:\oraclexe\app\oracle\product\10.2.0\server\network\log\listener.log
Summary of endpoints listening...
+(Description=(address=(Protocol=IPC)(PIPENAME=\\.\pipe\EXTPROC_FOR_XEipc)))+
+ (Description = (Address = (Protocol = TCP) (Host = xxxxxxx (port = 1521))) +)
+ (Description = (Address = (Protocol = TCP)(Host=127.0.0.1) (port = 8080)) (Presentation = http)(session=RAW)) +.
Summary of services...
Service 'CLRExtProc' has 1 instance (s).
Instance of 'CLRExtProc', status UNKNOWN, has 1 operation for this service...
Service 'PLSExtProc' has 1 instance (s).
Instance of 'PLSExtProc', status UNKNOWN, has 1 operation for this service...
Service 'XEXDB' has 1 instance (s).
Instance "xe", State LOAN, has 1 operation for this service...
Service 'XE_XPT' has 1 instance (s).
Instance "xe", State LOAN, has 1 operation for this service...
"Xe" service has 1 instance (s).
Instance "xe", State LOAN, has 1 operation for this service...
The command completed successfully
+ $> +.
---
+ $> sqlplus /nolog +.
SQL * more: Release 10.2.0.1.0 - Production kills Mar 31 16:54:04 2009
Copyright (c) 1982, 2005, Oracle. All rights reserved.
SQL > connect sys as sysdba
Enter the password:
Connected.
SQL > select * from v$ resource_limit where resource_name = '' process. ''
RESOURCE_NAME CURRENT_UTILIZATION MAX_UTILIZATION INITIAL_AL
------------------------------ ------------------- --------------- ----------
LIMIT_VALU
----------
processes 21 33 40
+ 40 +.
SQL > SELECT count (*) FROM THE process of v$.
COUNT (*)
----------
+ 21 +.
SQL > SELECT count (*) FROM $session v;
COUNT (*)
----------
+ 15 +.
SQL > SELECT * FROM v$ resource_limit;
RESOURCE_NAME CURRENT_UTILIZATION MAX_UTILIZATION INITIAL_ALLOCATION LIMIT_VALUE
----------------------------------------------------------------------------------------------------------------------------------------------------
gcs_shadows 0 0 0 0
dml_locks 0 57 212 UNLIMITED
temporary_table_locks 0 9 UNLIMITED UNLIMITED
0 7 53 UNLIMITED transactions
0 0 53 UNLIMITED branches
0 1 53 UNLIMITED cmtcallbk
sort_segment_locks 0 1 UNLIMITED UNLIMITED
11 11 53 65535 max_rollback_segments
max_shared_servers 4 4 UNLIMITED UNLIMITED
0 0 0 3600 PARALLEL_MAX_SERVERS
---
Any ideas as to what could be the problem?
Thank you
Amedeo.
P. S.
What is the syntax to create a block of code, if this forum?Hello
It isn't dinamyc parameter, so you need to modify the init.ora file.
that is incase you are usning init.ora file.
If you use spfile, you should
Run change processes control system = <# of="" proccesses="">scope = spfile;#>Thank you
Benjamin Gopal -
The requested itinerary has not been mapped in Spark
If I try to go to some Web sites, for example http://www.rtlnieuws.nl/ I get this message
The requested itinerary has not been mapped in Spark.
If I use Chrome I don't have this problemI solved the problem by cleaning the mind hidden CC cleaner
-
IMac using Firefox 8 and Yahoo as a homepage. When I click on a link of news it brings up the error message next - "your browser has requested that this server could not understand. A request header field exceeds server limit. When I use Safari it is no problem.
I did as b ^ 24554 and cleared out the cache and cookies and the problem seems to be resolved. Thank you.
-
The dhcp server has not seen a directory for authorization server
I recently upgraded from Server 2003 to windows server 2008 r2. After the upgrade, the DHCP server has started to not giving IP address after a lease has expired. For DHCP to provide IP addresses, I have to restart the server. I need help on how to configure my server to allow the service to restart. Any help will be much appreciated
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)* -
True color has not applied the requested settings - Dell Inspiron 5547
I bought Dell Inspiron 5547 last wee.
Since day 1, I get error of "True color has not applied the requested settings" . Now running Windows 10 (upgrade of 2 days).
Tried to update all the drivers. Is there anyone facing the same issue and got a fix?
Thanks in advance!
go to programs and features in windows 10, there you will find TrueColor application right click and press change, it will be to repair or reinstall the application. Even though I have upgraded to windows 10, true color works very well with me, yes sometimes it does, sometimes only. In windows update, you will get the update for graphics card intel it will be
Intel Corporation - graphic adapter WDDM1.1, WDDM1.2, WDDM1.3, WDDM2.0 graphics card graphics card graphics card - Intel(r) HD Graphics Family
just to update these things also, I remember seeing somewhere on the internet that intel could be the culprit for this problem.
After that repair is TrueColor 99% chance that it work.otherwise uninstalls true color and redownload it from there
Last thing, I would say, is dell people working on this issue itseems like they said to my friend who had the same problem when he called. wait patiently they release the fix.
Answer to what's going on
-
Get the error message:
Could not mount the file. It has not been possible to find a filter for the requested command.
Why is - this happens when I open documents using Mac advertising agency and I'm on PC?
Hi Mikael,
files have been archived in archive zip-file when transferred via the ftp protocol? I guess, not.
If the files were already placed in a document, InDesign on the agency side the following workflow might be the solution:
Office on Mac OSX:
1 package the InDesign document, as well as placed images and fonts of the necessary document with InDesign packing device.
2. the folder packed in a zip zip file.
3. download the zip file to an ftp server
You on Windows:
1. download the zipfile to your own workload.
2 unzip the zip on your workload. Do not delete the zip file.
3. rename the folder of the package to fit your scheme of naming of jobs (option)
4 rename the InDesign document to adapt to your schema naming of jobs (option)
5. open the InDesign file in the packed file.
Do not move or save somewhere else.
Alternative:
Work with Dropbox to share documents on a shared volume of Dropbox, if documents must move forward and backward between you and the Agency.
Uwe
-
Hi all
Can we add several table managers at sites in VMware SRM?
How to record several managers of the group a table copy in SRA?
"When I try to add new array manager of second table at one site I get the error message" SRA order "matrices of discovery has not not" adv0408 file not found in VMware Site recovery manager.
Versions: VMware SRM 5.5
Cruiser storage: Fujitsu Eternus SF v16.1, SRA 2.3
Thanks in advance,
RAMU Reddy
Thanks Stefan,
I contacted my storage team. It was with License Manager (ACM) advanced copy number. After license ACM registry in SRA Database of SRM server, everything was fine and I was able to protect all remaining VM.
Best regards
RAMU Reddy
-
Reinstall an app in the market shows. But this request has not been downloaded.
Two days back I tried to download some applications on the Marketplace.
But I didn't have any link to download the application.
In the market shows 'reinstall application. " But this application has not been downloaded.
Hello
You will need to work with the support to the market.
Answers is a technical support site of journal peer for Windows and other Microsoft products and
has nothing to do with market or third 3rd sites.I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
Maybe you are looking for
-
$9.88 credit and advertising. Is it possible to revert to the version I was using before this update? We try to protect our children consumerism and inappropriate content, and now they must face together when they want to visit their grandparents.
-
Emty battery Toshiba Satellite L550-202 without use
Dear readers, I have a Toshiba Satellite L550-202 with one small problem.When the laptop has full charge and stored in its case of transport of the battery is emty after a few days. (without help)Y at - it an explanation for that? Kind regards Ronald
-
Satellite A60-102: error with an autodesk autocad 2006
Hi all;Autodesk autocad 2006, I installed on my computer laptop satellite SA60-102, but it did not run and it displays an error saying 'DBX CASE 0' with 'ok', although I installed it on my desktop pc and it worked very well. I need your help ASAPNaim
-
BlackBerry Smartphones Can I have out of several email addresses on one device?
I have a BB 8700 g (t-mobile), but I'm ready to upgrade/change of provider. Device mgr software is ver 4.7. I have and intend to keep, NON-enterprise service. I have now sent E-mail to the device of multiple e-mail addresses, but when you reply, th
-
M620 servers, attention in newspapers, event ID 1004 IPMIDRV
I'm looking for a problem reported on two M1000E enclosures. The support function refuses to take on these servers, saying that they are affected by a caveat in the windows logs,"event ID 1004 IPMIDRV the IPMI device driver attempted to communicate w