What are the answers of code of HD521-2W SMART short self-test error when running the diagnostics?

Similar Questions

• The hardware diagnostic tool advises that the SMART short self-test has failed.

  The hardware diagnostic tool advises that the SMART short self-test has failed.

  Is this a problem? What can I do about it?

  Atelier42 wrote: the hardware diagnostic tool advises that SMART short self test failed.

  Is this a problem? What can I do about it?

  Hello Atelier42, this usually indicates that you have a hard disk failure.

  I would like to back up my data as soon as possible, just in case the hard drive breaks down actually.

  You must also make sure that you have the HP Recovery restore set for your system recovery disc in case you do not want to replace the hard drive.

  With this restore HP Recovery disk set, you could replace a defective hard drive and use this disk set to your HP system back as it was when shipped. Then, you could put your data saved on your system.

• failure of the targeted reading test and smart short self-test

  I have over problems with my computer is - it related to software or hardware?

  Please advice

  • The purpose of S.M.A.R.T. is to warn a user of imminent drive failure while there is still time to take action, such as copying the data to a replacement unit.

  The above is an excerpt from the article below:

  S.M.A.R.T.
   http://en.wikipedia.org/wiki/S.M.A.R.T.

  The thread below from Windows SevenForums describes possible solutions:

  Windows 7 - SMART short self-test fail
   http://www.SevenForums.com/hardware-devices/148900-smart-short-self-test-fail.html

  I strongly suggest you to immediately perform a backup of all your personal files, data, and anything else that is important for you to external media (an external IMO is better but you can also use CD/DVD or a USB flash drive) until the hard drive breaks down.

  Kind regards

• SMART short Self Test Failed - (error code: WHD16-8NR)

  Hi all

  I had my XPS L520X for 4 years and 2 months. I've never had a problem with its operation until last week. Randomly, it restarted and came with the PCI Realtek issue when it restarts.

  To cut a very long story short Fault find it which is going on, I reinstalled the entire operating system, including formatting of the hard drive.

  The problem of the laptop different freeze/crash and reboot with erros while doing normal tasks has not been resolved.

  I have run the Dell support center software and it shows the auto SMART test failed with the following code (error code: WHD16-8NR).

  Event log:

  Dell Support Center log file
  March 17, 2016 16:53:55
  Overall result: failed

  -------------------------------------------------------------------------------------------------------------------------------------------
  ST9750420AS [ATA:0:0\\?\ide#diskst9750420as___0005dem1#4&34e0611c&0&0.0.0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b]}
  -------------------------------------------------------------------------------------------------------------------------------------------

  Seller: Seagate
  Model number: ST9750420AS
  Serial number: 6WS100EG
  Firmware revision: 0005DEM1
  Size: 698,6 GB
  Rotation speed: 7200 RPM
  Cache size: 16 MB
  Temperature: 43 c
  Physical sector size: 4 KB
  Logical sector size: 512 B
  Count of logical sector: 1465149168
  Supported standards: ATA8-ACS, ATA/ATAPI-7, ATA/ATAPI-6, ATA/ATAPI-5
  Specification Version: Rev ATA8-ACS 4

  ----------------------------
  OS - C: [PARTITION:C\\.\C:\]
  ----------------------------

  File system: NTFS
  Volume serial number: 5087-8802
  Volume capacity: 679.00 GB
  Amount of free space: 568,63 GB
  Volume space used: 110,37 GB

  Test of the SMART State

  Test started - 17/03/2016 16:43:57
        
  Finished test:-17/03/2016 16:43:59
  Past

  Test of SMART thresholds

  Test started - 17/03/2016 16:43:59
        
  Finished test:-17/03/2016 16:44:01
  Past

  Targeted reading test

  Test started - 17/03/2016 16:44:01
        
  Finished test:-17/03/2016 16:44:05
  Past

  Try to search randomly

  Test started - 17/03/2016 16:44:05
        
  Finished test:-17/03/2016 16:44:54
  Past

  Funnel Seek Test

  Test started - 17/03/2016 16:44:54
        
  Finished test:-17/03/2016 16:46:14
  Past

  Short what SMART self-test

  Test started - 17/03/2016 16:46:14
        
  Error message:-17/03/2016 16:46:24
  The unit has reported the following State: the previous self-test completed having the read element of the test failed.
  Error message:-17/03/2016 16:46:25
  The first default LBA value is 121243744 and the failure occurred after that the device was working since 8792 hours under tension.
  Finished test:-17/03/2016 16:46:26
        Failed (error code: WHD16-8NR)

  Surface Scan Test

  Test started - 17/03/2016 16:46:26
        
  Finished test:-17/03/2016 16:47:25
  Past

  Surface Scan Test - 2

  Test started - 17/03/2016 16:47:25
        
  Finished test:-17/03/2016 16:48:58
  Past

  I also went in the BIOS BOOT MENU by pressing F12 at startup and ran diagnostics that seemed to have said everything going, however I saw a mistake, faliure in its process that was too fast for me to write the error.

  In a nutshell, my thought is that my hard drive has failed / is corrupted or is about to fail.

  My simple question is, do I need a new hard drive with the information I've provided?

  Thank you very much!

  To all those who read this topic:

  I rang Dell directly and they confirmed my hard drive needs to be replaced.

  8792 power over time, I think that its actually me good.

  Bravo and thanks for the reply ejn63

• SMART short self-test - on the second hard drive

  HP Pavilion Elite e9270t - 3 yrs old, Win7.

  Became the error SMART self-test short the original drive so I installed a replacement and transferred files.

  I get the same error on the second h/d. I have my doubts that the second disk is having the exact same error and wonder if the s/w test is actually the problem.

  It could very well be the connectors that gives you the question instead of the HARD drive itself. I would run the HARD drive test in BIOS instead of the short test.

  Try this:

  1. Plug the AC adapter into the computer if it is not already connected.
  2. Turn off the computer and wait five seconds.
  3. Press the power button to start the computer and repeatedly press the F10 key to enter the BIOS Setup menu.
  4. Use the right arrow or left arrow keys to navigate the menu selection to find the Auto test primary hard drive option. Depending on your BIOS, it is under diagnoses or tools.
  5. Select self-test primary hard drive, and then press the Enter key to start the test.

  Figure 1: Example of a primary hard disk self test screen

  
  

  The hard drive self test performs a Quick Test , followed by a complete Test. During each test, the window displays a status bar and a scheduled for completion

  Let me know the results of this test.

  THX

• Monthly diagnostic equipment. Failure is SMART short self-test (HD521-2W).

  What's to worry? If so that will fix it?

  saltyern wrote: what's to worry? If so that will fix it?

  Hello saltyern, this failure usually reports at the beginning of hard drive failure. I backup my data as soon as possible and consider replacing the hard drive as soon as possible.

  You must have either already predict a HP Recovery disk set, restore your system which can be used to restore the software you need to replace the original hard drive.

  Here is a link that has additional information on this issue.

• What are the causes of silverlight N8007 error code.

  What are the causes of silverlight code error N8007?  I have already been able to view the contents of netflicks, but no more.  He has always played by this "Silverlite" program or a recent change?

  Thaks in advance for your answer.

  Hi GaryFelder,
   
  Post your request in the Silverlight forums for assistance on this issue.
   
  Visit the following link to do the same thing:
  http://forums.Silverlight.NET/

• I want to uninstall my old CS5 Design Premium from my computer to reinstall it on another computer. What are the steps? Is there something special with the activation codes, etc.?

  I want to uninstall my old CS5 Design Premium from my computer to reinstall it on another computer. What are the steps? Is there something special with the activation codes, etc.?

  You are allowed to have two facilities enabled, so if you prefer you can keep ut on the current computer and just install it on the new as you did initially.  If you want to remove on the other machine, the first thing to do is to disable it by opening a program in the suite and by selecting help-> turn off in the top toolbar.  That's all you need to do to disable the software.  At this point if you prefer you can uninstall it if you want.

  As much as on the new nmachine, as I indicated just, just install it like you did the first time.

• What are the BCD entries to TWO instances of dual boot of Vista professional in TWO separate hard drives?

  What are the BCD entries to TWO instances of dual boot of Vista professional in TWO separate hard drives? -Dell Vostro 1710, my wife had to be returned to Dell, I installed its Vostro hard drive in my Dell Vostro 1710 SAME, but I don't get a menu starting double when I turn on my Vostro. (Both Vista Business operating systems are licensed separately).

  I would like to start his drive hard so that it looks like 'his' office on 'his' computer.

  Thanks for any advice.

  Split of: http://answers.microsoft.com/en-us/windows/forum/windows_vista-windows_install/how-do-i-set-up-a-dual-boot-vista-and-xp-with-2/d1e95c26-0e48-4a8d-9e0f-526da19dce52?tm=1336794280998

  The easiest way is to use the DualBoot Pro.  He has the tools to write the necessary code automatically.  It is excellent for managing the tasks you want to do.

  However, you have a potential license problem.  Even if your Dell has the exact code in the BIOS to activate the copy of Windows on the hard drive of your wife, the computer is only allowed for an OEM copy.  If Dell is back after repairs then you should be OK once you have turned on the hard disk in his computer of your wife. You can delete the entry of additional start with DualBoot Pro menu,

• Hardware change - inform them where and what are the details to be informed

  Hello!

  I want to use my hard drive, change the map motherboard and CPU only. Who should I email and what are the details I need to provide to get my two windows xp and vista activated and validated after having reformatted and re-installed?

  If I happen to call by phone I phone number of the customer care person knowing Tamil language?

  Kind regards

  Components

  You must notify anyone.  If you have problems activating automatically after the changes, do it manually.

  To activate manually, go to start, search, and type in slui 4 enter.  Enter your country and press Next.  You will be on a screen with a phone number and a bunch of codes below.  Dial the number and browse automatic guests until you get to a human being.  Have your handy product code because it will be asked.  Explain the situation, but it's the same PC and only installed on this PC.  They should give you a code to enter on this screen to activate Vista.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• What are the relationships between the logging and IKM?

  What is the best method to use in the following scenario:
  I have about 20 tables with the large amount of data sources.
  I need to create interfaces that join the source tables in target tables.
  The tables are inserted every few seconds with about hundreds of thousands lines.
  There may be a gap of a few seconds between the insertion of different tables that could be attached.
  The source and target tables are on the same Oracle instance and schema.
  I want to understand the role of: 'Logging CDC' and "IKM - incremental" and
  How can I use it in my script?
  In general, what are the relationships between "Logging" and 'IKM '?
  Use both? Or maybe it's better deelte and insert the target tables?
  
  I want to understand what is the role of "Logging CDC"?
  Can 'IKM - incremental' work without "logging"?
  Must 'Logging' have PK on the tables?
  What should I do if I can't say PK (there may be several identical lines)?
  
  Yael thanks in advance

  user604062 wrote:
  Hello
  Thanks for your quick response!

  No probs - its still fresh in memory I did a major project on this topic last year (400 tables, millions of lines per day (inserts, updates, deletes), sup-5 minute latency). The problem is it isn't that well written on the web, that you have read the blog of the example I linked to in my first answer? See also here: http://odiexperts.com/changed-data-capture-cdc/

  Always on logging:
  My source table is inserted all the time.
  The interface to join the source table in the target table.

  In ODI, the correct term would be your source table "fits" in the table target, unless you mean literally that want to join the the source with the taget table table? My question if you want to do with the result of the join?

  What exactly the "journaling" CDC updates?
  It updates the model of ODI? interfaces? The source of data in the model of ODI? The target table?

  Logging CDC configures and deploys the data capture mechanism (Triggers or log based capture, IE Logminer/streams/Goldengate) - it is not updated the model as such, she pointed out the metadata of the model of ODI repositoty as a CDC data store, allowing you, the developer say ODI to use log data if you wish (reported in the interface) There is no change in the target table, you get an indicator of metadata (IND_UPD) against a line during the integration (in C$ and I have tables$) that tells you if its insertion (I) and update (U) or deletion (D). It had ' lines allow you to synchronize the deletions, but yoy say its inserts only then you probably used use this option. "
  So the only changes are the source table to your interface, another diary data (if you use logging) or the table of the actual source (if not using the logging).

  This is the main thing that I don't understand!

  I hope I made a little clearer.

  Try the following as a quick test:

  Reverse a source table an engineer and the target (at least) table.
  Import the update incremental LKM and IKM.
  Import of the JKM you want to use.

  Create an interface between the source and the target without any deployed JKM.
  Configure the options of JKM on the model, the "Start log" to start the process of capture - this is quite a complex stage and a lot of things to understand what is happening in the source database, better to check code ODI sends to the database and to review the documentation of Oracle database for a description of what his weight (instantiate Tables (, sets of creating change, creation of subscribers etc. establishment of newspaper groups, creating views Journalising etc.) -you will need to consult your Source DBA database initially as ODI wants to make many changes to the source DB (in mode Archivelog process max, parallelism, size, Java etc.)

  Now, edit your interface and mark the table source for use "Journalized data bank.
  Restart your interface
  Compare the difference in the generated code in the journal of the operator, see the differences of the operator.

  >

  Thank you, Yael

• What are the costs associated with the synchronization

  What are the costs associated with the synchronization

  Simple answer is: No. Cost zero.

• What are the best settings to standard calibration for the XBR65X850C?

  What are the best settings to standard calibration for the XBR65X850C?

  Hi DRATCLIFFE,

  Thank you for your time to write a post.

  We are very sorry for the late reply.

  Change the picture or the sound settings of your TV depends on your preferences and on what you watch/listen to.

  You can use the settings preset for image and sound.

  In addition, to better enjoy your viewing experience, follow these steps:

  • Install the latest software update. The updated software and the driver for your Sony product are available online.
  
  
  • Set the automatic software download setting to automatically download software updates.

  Thank you
  ^ Ron

  If my post answered your question, please mark it as "accept as a Solution.

• What are the icons on top of gmail

  When I use gmail on my iPad, there are 5 icons on the top.  The first three are a flag, a folder and a file.  The last two are an arrow (for you answer and transfer, etc.) and a new message icon.  I just want to know what are the first three.  I have searched but cannot find anything. Thank you.

  Flag = flag for later review / attention / reminder to do something

  File = move to a different folder

  Drop the box - Archives

  (1150)

• What are the units of the DAQmx meter?

  Hello

  I created this VI and several others like it, a few months ago, but I forgot some of what I have at the time.  I believe that this VI should measure period, using the counter on the chassis of the acquisition of data.  Can someone tell me the units of the measurement period?  I think it's seconds, but I am trying to find a way to understand this!  The period values are generated by the DAQmx READ function in the WHILE loop.  What units that work out in the table?  What are the units of the elements of the array, essentially?  See the attached VI.

  In addition, how do you know?  I opened the DETAILED HELP for the DAQmx Read (minimum 1 D NSamp DBL) shows the VI but, I can't find anything on the units of data coming out of the Terminal marked data with the orange wire, which is actually an array of periods, and we take the average of the most recent measures period 15 or more.

  I had a suggestion months ago for a line OR manual containing a description of the measures of buffering EdgeCounting, but when I went to find it, the link had been changed by NEITHER, so I find that manual, but I think the answer is probably there because I remember this manual is very helpful when I've done it before.

  Thanks for the tips.

  HI dav2010,

  When you create a virtual channel, you must specify the units of the task of counter uses.  There are several options that are listed in help here:

  http://zone.NI.com/reference/en-XX/help/370469AA-01/lvdaqmx/mxcreatechannel/#DAQmxCreateChannel%28CI...

  I'm not on a computer with LabVIEW now, but I think the default should be ticks, which is the number of ticks the time base of your device.  You can find this information in your hardware specifications.

  Kind regards