When I start the machine, continuous hard drive work for almost 1/2 hour, meanwhile if I open a program, the machine runs very slowly. Help solve the problem please

Similar Questions

• The hard drive works for 1/2 hour at the start before I can use the computer.

  I tried all the registry cleaners, etc. with nothing doesn't. Is there a way to know what is happening during this time?
  I use AVG virus and tweak.now for other things.

  Hello

  1. have there been recent changes to the system before the show?

  2. what disc hard are you referring?

  Method:

  Follow the link below and run the disk check. Check if it helps.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

  Let us know if it helps.

• error message: "no audio output device is installed" I have no sound - how to rectify the problem please?

  reinstall audio devices-error message: "no audio output device is installed" I have no sound - how to rectify the problem please? tried most of the quick fix ideas, but nothing seems to work

  Hi Jammyhorse,

  1. What is the number of brand and model of the PC?

  2. when the problem started?

  3. you remember to make changes to the computer before this problem?

  Step 1:

  You can check the following link and run the Fixit and see if helps solve the problem.

  Diagnose and automatically repair audio playback problems

  http://support.Microsoft.com/mats/NO_SOUND/

  Also check out the link:

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  Step 2:

  In the BIOS settings advanced, you can also check if the onboard sound is enabled.

  You can see the manual of the system manufacturer or contact the system manufacturer for more information on how to make the changes in the BIOS.

  Note: Change to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How many times can I install Windows 7 on your PC even after I continue to update the hard drive SSD for a bigger?

  How many times can I install windows 7 on your PC even after I continue to update the hard drive SSD for a bigger? Unlimited?

  Mike

  There is no limit.

• When I transfer files from my hard drive on a USB flash drive, the transfer rate is very slow, about 250 KB / second. Is it possible to increase the speed of transfer rate

  When I transfer files from my hard drive on a USB flash drive, the transfer rate is very slow, about 250 KB / second. Is it possible to increase the speed of transfer rate

  depends on the speed, support USB 2.0, USB 2.0 ports, and with active BIOS settings

  (2) you can increase the speed, if your motherbaord has a USB 3.0 port and must be enabled in the BIOS

• Windows 7 Professional 64 bit explorer.exe hangs in my computer when I right click on my hard drive. Disks appear in the Solution Explorer or eject.

  I have a serious problem when one of my windows, my main Administrator profile profiles, is very strange. Other profiles created on the computer, the administrator or standard user, all do not have this problem. The problem is when I open my computer, on my main administrator account, my hard drive is not recognized. There is a disc in the drive and it will not eject, nor will it recognize one is in the computer. The drive will appear in my computer, but there is no information on the icon about what drive is in the computer. Secondly, when I right click on it, the computer freezes and crashes explorer.exe. Once I have restart explorer.exe everything goes back to normal, but the problem is still there. I have this problem on other users on my computer. A system restore did not work, nor has a registry restored to an earlier period. In addition, everything else on the computer works fine, and there is NO virus or Trojan horses. I ran several deep scans with two different software, Microsoft Security Essentials, and Malwarebytes. I've taken I have a corrupted user profile and try to transfer my files in a new profile through the instructions from microsoft on their Web site. When I finished this profile has been impossible to obtain the necessary permissions to use files and I got errors trying to open anything. This problem has a solution, and I refuse to do a restore on a computer that otherwise does not work correctly. I would not have to re - install the operating system, or transfer my profile on a new resolution to this problem. Can someone at Microsoft help solve this problem? Thank you

  Hello
  See the link below:

  Difficulty of a corrupted user profile
  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

• How to make a virtual computer to connect to a CD player with an ISO mounted when you start the virtual machine?

  I am the creation of virtual machines using PowerCLI 5.5 on vSphere 5.0; and while the virtual machine is turned off, I am able to mount an ISO on a CD player and change the boot order to boot from the CD-ROM (for another post).  I have the flag startConnected set to true, but am not having much luck getting the virtual machine to connect to the CDDrive

  $cdObj = $Vm | New-CDDrive - IsoPath $isoPathName - StartConnected: $true

  If ($cdObj - no $null)
  {
  #Power off VM if it is on
  $VmState = $Vm.PowerState
  
  If ($VmState - eq "Receptor")
  {
  $Vm | Stop-Vm-confirm: $false - ea 0
  }

  $BootHardDiskName = 'disk 1 '.
  $VmView = get - VM $VmName - Server $serverObj.Name | Get-View
  $HardDiskDeviceKey = ($VmView.Config.Hardware.Device |) Where-Object {$_.} DeviceInfo.Label - eq $BootHardDiskName}). Key

  $BootableHardDisk = new-Object - TypeName VMware.Vim.VirtualMachineBootOptionsBootableDiskDevice - property @{'DeviceKey' = $HardDiskDeviceKey}
  $BootableCDRom = new-Object-Type VMware.Vim.VirtualMachineBootOptionsBootableCdromDevice
  
  #Set for CDRom boot order
  $BootIso = new-Object VMware.Vim .VirtualMachineConfigSpec - property @ {}
  "BootOptions' = New-Object VMware.Vim.VirtualMachineBootOptions - property @ {}
  BootOrder = $BootableCDRom
  }
  }
  
  #Set VM from the start settings at the start of the first CD and forces the display to update (sometimes delayed)
  $VmView.ReconfigVM_Task ($BootIso) | out-null
  $VmView.UpdateViewData ("Config.BootOptions.BootOrder")
  
  #Power on VM
  $Vm | Start-VM-confirm: $false - ea - global 0EV: vmOpsError | out-null

  When I start the VM, it does start the ISO.

  If I go to vCenter, the CD is pointing to the ISO file, but the 'Connected' to change settings option is not checked;  I can restart the VM of vCenter and then the VM restarts the ISO, but not in the script.

  I even put code to add a lead time of 5 to 10 seconds; I restart the virtual machine twice in the script and I can't CD to connect to start the virtual computer.

  Appreciate any suggestions.

  Maureen

  Have you tried to do a

  Game-CDDrive - CD $cdObj - connected - confirm: $false

  immediately after the start-VM?

• The desktop icons and taskbar are at least three minutes to load when I start the computer.

  Original title: problem with the desktop icons

  All of a sudden when I start my computer, the icons on the desktop and icons at the bottom of the clock of the take at least three minutes to load, and before that time, they used to load in a few seconds.  Also, I have no problem with the computer start.  Any help to solve this problem will be greatly appreciated.

  According to the specifications of your system, hard drives on your system are disks IDE (not the SATA drives).

  Sometimes the Interface IDE mode can change from DMA mode to PIO mode and when that happens, things sudden. run very slowly, but it is easy to check and adjust if you need to.

  Here's how:

  If you are using IDE drives, use Device Manager to check the channel Transfer Mode IDE is set to something like DMA if available (depends on your hardware) and the slow PIO mode.
    
  Don't forget: PIO is the slowest, DMA is faster.

  It is easy to check and usually easy to fix and the mode would not have changed in itself, so if she changed to PIO, change it to DMA, and then understand why it changed and fix it.

  To launch the Device Manager console, click Start, run and enter in the box:

  %SystemRoot%\System32\devmgmt.msc

  Click OK.

  Expand the section controller IDE / ATA to see your IDE channels. Each right click and choose Properties for each channel that has a tab advanced settings, determine the Transfer Mode. There are usually 4 channels to check in a desktop computer, maybe less for laptops.

  Faster selection will always be a kind of selection DMA (usually: DMA DMA5, UDMA, etc.).  If it is PIO, change it to DMA.
    
  If you are unsure of what you see after return of help and advice.
    
  If you make settings, restart and check the settings again to make sure that any change stick.
    
  What may have caused the change?
    
  http://support.Microsoft.com/kb/817472

• I have Win7 64 bit ultimate and from time to time when I start PC my card reader drives do not appear in my computer.

  I have Win7 64 bit ultimate and from time to time when I start PC my card reader drives do not appear in my computer. Device Manager indicates that they are working correctly. Sometimes my dvd drives disappear. I have to do a system restore to solve this problem. For some reason any Win7 has problems with storage devices. How to stop these dissappearing from my Computer(or not getting a drive letter assigned) storage devices?  It's very frustrating. And, System Restore is not a way to solve this problem, it's just a quick fix. I have three internal hard disks, three hard drives, card reader external drives, USB keys, disks, etc. I need a way to solve this problem when it happens. So far, happened about 9 times in the last six weeks since I installed Win7 64 bit ATU.

  There may be an update of the motherboard BIOS to solve the problem.

  Otherwise, as your card readers are no doubt attached via USB the usual way to solve this problem would be to uninstall the drives and the USB controllers and devices in the system restore.

• Sometimes when I started, the windows display is biased and the Start button is off the screen. What's wrong?

  Sometimes, when I started, the windows screen display turns on but is so out of the Center, (with a black border on the left) that the Start button is not on-screen. and I have to log off. I continue to log and, in time, the screen lights up properly. But the "wrong views" seem to be increasing. What's wrong?

  This means your driver or monitor if your desktop has a problem. See if it boots OK safe mode

• When I start the editor of 11 items PS, I get this message: "this program cannot start because MSVCRT10.d.

  When I start the editor of 11 items PS, I get this message: "this program cannot start because MSVCRT10.dll is missing on your computer. Try reinstalling the program to fix this problem. »

  When I try to close the error dialog box, the message reappears immediately and the program does not load. After rejecting the dialogue time 8 or 10 or 12, the editor finally support and everything works fine.

  How can I solve this frustrating problem? I have already uninstalled and reinstalled the program and who has not solved the problem. If I need to add a .dll file to my machine, where can I find it and where should I put it on my computer?

  Thank you

  William Driver

  Using inferential holmesien and Spadian skills of inquiry, I discovered that the problem lies in a third-party filter application. I determined that since the program gave me the error message when PES 11 has begun its analysis of filter plug-ins, then the problem may lie there. I removed the filter plugins from the program's ' Plugins' directory to another folder and add back one by one until I received the error message. Of course, I have finally found the plugins defective and withdrawn. PES 11 now loads without problem.

  Thanks for your help.

• We went to MacOS Sierra of El Capitan and now have to log in twice, when we start the computer.

  We have upgraded to Mac OS Sierra of El Capitan, and now we have to log in twice, when we start the computer.

  How fix us this?

  Thank you...

  All the best...

  God bless...

  If you have activated the preferences-> Security-> FileVault system, then you must enter your password initially so that device drivers can decrypt your encrypted drive.  Once the system is running, you must then log into your account.

  They are really 2 separate activities that happen just to use the same password.

• PhotoSmart AIO 7520: Could not find the place to activate the scan function when I start the system

  My scan of the computer is turned off when I start the computer... How to activate it automatically?

  Hello

  Have you installed the software and driver on your computer? Can you see HP Scan in

  Start > all programs > HP > HP [printer] > HP Scan?

  You can click HP Scan from there.

  Kind regards.

• How to stop the pop-up for saving files when I start the computer?

  I was going to save files on a drive of DVD-CD-R, but I decided to do not, how can I stop the pop-up for saving files when I start the computer? It keeps appearing even though I cancelled check?

  * original title - cancel recording of dvd/cd-rw *.

  Hello

  Windows displays a temporary storage area where files are held before they are copied to the CD. Files or folders located in the temporary storage area are listed under files ready to be written on the CD.

  Try the steps and check them off below if it helps:

  a. double-click my computer and then double-click the CD burner.

  b. under CD writing tasks, click on delete temporary files.

  When you delete the contents of the temporary storage area, you can set this field to another set of files and folders that you want to copy to the CD. The files are not deleted from their location on your computer or on the CD.

• When I start the system, I get the message "failed to load Launcher dll" I hit OK and the system load and seems to work.

  I am under Windows Vista Home and when I start the system, I get the message "failed to load Launcher dll" I hit OK and the system load and seems to work. I'm afraid that something is not correct, what do you recommend? The two available Service Packs have been installed.

  Discussions were merged.

  Deleted duplicate.

  Original title: failure of the Dll

  The error seems to be a common problem with Dell laptops:

  http://en.community.Dell.com/search/#q=Lanucher%20dll&sort=rating%20desc&defaultAskForumId=0&pi1680537405=1

  It seems that apoint.exe gives the error that indicates that the problem is with the Alps touchpad driver.

  Try to uninstall the Alps touchpad driver and then install the latest version available from Dell for your laptop:

  http://www.Dell.com/support/home/ca/en/cabsdt1/product-support/product/Inspiron-1545/drivers