When you add the network printer

Similar Questions

• Error 0X0000000D when you add the network printer at home

  Original title: try to add a printer to My Desktop 2 which is connected via a USB port on my desktop computer 1. Both are pre-cabled linked to my home network. They are both under Vista.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  1. Programs that you have problems with adding printer
  • Error 0X0000000D
  • Recent changes made to your computer no
  • What you have already tried to solve the problem, not yet

  Usually, you insert the printer cd in desktop1 and follow the procedure for setting up a shared printer / network

• Satellite A500-1GL: it is advisable to remove the battery when you use the network

  I know this is a silly question but its actually something I know not so thought I would ask.

  I almost always plug my laptop into the supply line (satellite a500 1gl)
  I was wondering have you actually keep the battery installed even when using the electrical network.
  Or is it really advisable to remove the battery when you use the network?
  I didn't know if the battery should always be in place.
  Thanks for your help
  Torti

  Hello

  A few years ago it was recommended to remove the battery of the laptop if the AC adapter is plugged. What keeps the constant charge battery
  New age of batteries are better you can leave the battery in the Bay it s ok and it should not affect the performance

  However, sooner or later each battery would die it s only a matter of time, you know

• "Limited connection" when you configure the network between two computers XP.

  Original title: Configuration of the network connection

  Trying to establish a network connection between two home PCs., both running Windows XP Pro. Have been through the network on both PC Setup Wizard but, they still say limited, in fact no connection. I use an Ethernet cable between the two Crusader. If it is true what I'm doing wrong?

  Thanx Terry

  Old but good, networking tips from MVP Malke, MS:

  The best and simplest is to buy a wireless router. This way you get Internet connectivity both machines and the added benefit of security more between you and the Internet. Then you configure your network wireless safely, and then you configure file/printer sharing. Here is information on the implementation of a router and also in networking. It seems long, but don't be intimidated. Setting up a router and the LAN of sharing between two computers takes about 15 minutes.

  The router configuration

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.

  2. attach a cable (usually supplied with the router) course Ethernet cat5e Internet/WAN port of the router to the Ethernet port on the cable modem.

  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.

  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

   

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar.

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). If you have a newish computer, you will be able to affect security WPA2-Personal Mode. Do this and enter a password. The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the Ethernet cable and wireless of the computer should see your new network. Enter the password you created to join the network and start surfing.

  *****

  B. file/printer sharing of

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus with "Internet Worm Protection" (like Norton 2006/07) which acts as a firewall, you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this. The instructions on this link work for XP and Vista:

  Set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.

• Error in get LV class by default when you open the default printer

  I am using vi text report easy to print text to the default system on a touchscreen Windows XP Embedded PC printer.

  When I run the simple VI I wrote (attached) I get a file not found error 7 in the LV ranks default vi when new report vi is called.

  The path in the default on the LV class value get's strange appearance; Here it is:

  c:\Torqo\USB Example.exe\1abvi3w\vi.lib\Utility\NIReport.llb\Standard Report\NI_Standard Report.lvclass printer

  The first elements of the way little look OK - player C and file Torqo that I'm short and the name of the application. Then it seems really weird.

  I use remote debugging on the touchscreen integrated for XP but it has the same error if I just run the .exe on the touch screen

  I can open Internet Explorer on the touch screen and print from it to the default system printer (it's an Epson printer).

  It smells kind of some package DLL or runtime package is not loaded on the touchscreen - but what it could be?

  I loaded the LV 2010 Runtime Engine LVRTE2010std.exe and the VISA DURATION visa503runtime.exe

  My vi normally works on the development of Windows XP SP3 without error System.

  In turn is a simple way to imitate printf or print serial port inside Labview, only to a USB port?

  I just need simple ASCII text that is sent to the connected USB printer.

  Any ideas for me?

  What's with the weird class path?

  I am a fairly new LV programmer but a Windows .NET programmer for a long time.

  Thanks in advance.

  I have no experience with the help of LV with XPe, so I can't help you there, but I can talk about the way - the EXE is essentially a folder structure that has been compressed into a single file. Inside this structure, LV place shipping screw in a folder called 1abvi3w so that they can be referenced by using a logical path (1337 is to avoid potential collisions).

  The only thing that I can suggest the hand is that you go into the build specification and explicitly include the report class when the generation by adding it to the section to always include. Theoretically, this happens automatically when you use the class, but maybe something is malfunctioning? Perhaps XPe does not pathnames within files exe or dynamics of decompression of the EXE file?

  If this does not work, you can also change the specifications of construction to place the report class at a specific location outside the EXE or go to the Advanced page and set the build to use the 8.x - style paths, which could help you, because I believe that it should generally put classes to report outside of the EXE.

• Cannot create document empty when you open the label printer software

  I installed the software to store 8 labels intermec for my label INTERMEC PF8t printer, when I try to open the message cannot create an empty document when you open the printer software labels appear. Help, please

  Hi Phaphama,

  ·         Did you do changes on the computer before the show?

  ·         He has already worked on the computer?

  Follow these methods.

  Method 1: Uninstall and reinstall the software and check if it works very well.

  How to change or remove a program in Windows XP

  http://support.Microsoft.com/kb/307895

  Method 2: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Startand then click run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  If the problem still persists, contact the manufacturer for more help and information.

  http://community.Intermec.com/Intr/

  http://www.Intermec.com/support/index.aspx

  http://www.Intermec.com/products/pswlblshop/index.aspx

• Video AutoPlay when you add the interactive button

  I'm having a problem with a video slide auto play when it is added an interactive button.

  The first slide of the project, I have an interactive index climbing to different slides. When he jumps to another slide video slide goes automatically into play, but when you add an interactive button to return to the home page video auto is more parts.

  I added the SS to display the index and video slide.

  Just a guess here, but generally a button has a built-in break. You should maybe check and adjust exactly where the break is underway.

  See you soon... Rick

• When you add the same audio clip of chronology not added?

  When I add a clip to the timeline of the first audio is also added as usual. When I add the same clip again, that it does not come with the linked audio file. When I hover over the blue icons in the project window, it is said "audio video used 2 times 'and' related used 1 time" I want audio to be also with the clip on the second clip. Why does this happen?

  FAQ: Why no audio or video will not at the track where I let down?

• OfficeJet 6500: Fax appears not when you add the printer with El Capitan

  I've just upgraded to El Capitan.  I have a 6500 Officejet and Officejet 6700 on the network and that you can print on both but fax is not working.

  I tried to delete faxes from the Printers & Scanners window in the settings, but when I try to add more once they are not appearing in the list.  When I click on add everything I see is the following:

  

  It should be an option fax for two (well I want that the created such as 6700 6500 is not connected to a phone line).  Anything I can try to get the Fax option to appear so that I can set up the Fax network (the printer is in a different area of the building so my work around printing and then manually fax is a pain - unfortunately, one of our main suppliers insists on faxes and will not accept orders by email if I need this to work!)

  By the way I tried selecting the 6500 in the list and then change the print to fax driver driver in the area of USE, but the printer is not sending it by fax - print only a few pages of garbage.

  Any help would be great because I find it very frustrating.  Also, I have another Mac with Yosomite on which has the same problem, so I don't think it's specific to El Capitan (but mine was working when I got Yosomite, but I installed the printer/fax under an earlier version originally).

  Try to update the software by following these steps:

  First of all make sure that the printer is turned on and connected to your Mac or on the same network.

  Click on the Apple icon, then select about this Mac.
  Click software update, and then click the Store from the top of the indicated window menu and click on reload the Page.

  Be sure to install any update HP or Apple, then check for the difference.

  If it persists, try manually install the package below:
  http://support.Apple.com/kb/dl907

  Search for now no difference.

  Note that it may take up to a minute for the Fax queue to appear.

  Shlomi

• How to add the warning message when you use the function 'print' in Adobe LiveCycle Designer

  I'm trying to make the pdf document for my business that requires the addition of a warning message while everyone to use the function 'print' page...

  Does anyone know how to add the warning message about LiveCycle Designer

  Also my supervisor mentioned something using "nag" If that sounds at all

  Not in the XML code, in the case of script of pre-publication of the "print" key. If you don't have the script editor to the top on your version of designer, you can press ctrl + shift + F5 to bring it.

• Failed to add the network printer

  Hello
  
  We have a client that connects to our ERP system to print orders.  They connect through a VPN site-to-site and then access our system through an RDP connection to a server 2008R2 instance.  The printer is a HP LaserJet 4100tn
  
  When I first set up in the spring I was intending to use the easy print with the redirect to printer driver to print orders.  However exceptionally slowly printed orders and I was not able to determine why.  Instead I've implemented their LaserJet as a local printer on our desktop server remotely using a HP LaserJet 4100 Series PCL6 driver.  It worked perfectly, and they have been printing without problem until yesterday.
  
  Yesterday for some reason any printer stopped working.  On our Remote Desktop server, it appeared as grayed out with an exclamation mark above.  I did the following diagnosis:
  
  > They can print from their own local office it
  > They changed and turn it on again
  > I can ping the printer from our server OK
  > I can get on the web interface of the printer OK from our server
  > Restart our server remote desktop
  > Turn off the Windows Firewall on the Remote Desktop server
  
  I therefore decided to remove the printer and add it again.  I go through the configuration wizard Windows printer usual choosing to do a new TCP/IP port, but when I put the IP address of the printer in Windows says that it is not the printer on the network (photo attached).
  
  I tried to delete the printer port which has been associated with this printer and remove the driver but Windows still won't "see" the printer.
  
  I am able to configure this printer on other servers from RD (2003 and 2008) and I also tried setting up on an old XP box, I had to hang out without problem.  Curiously, it seems only that this server is the only one that I can not set up the new even if it can ping the printer OK.
  
  I found a troubleshooting printer HP hereWeb page but who was no help, and the software does not work on Windows Server versions.
  
  Don't know what to do next!

  This was solved by changing the IP address of the printer

  After changing the IP address, I was able to add the printer to the server OK.

  I wasn't able to find out why this is the case, but guess it is some incorrect IP or the information stored in the registry.

• Error message when you add the account to TimeMachine

  Hello

  I get the error in system.log when I enter my account information to access a drive for time machine below

  System.log:Feb 14 11:31:04 iMac - 5 K sandboxd [133] ([25623]): kcproxy (25623) political system: deny /Library/Keychains/System.keychain file-writing-untie

  The above error appears when you use access Keychani to run the add-in, when I use the route of the control panel to add I get a slightly different error

  System.log:Feb 14 11:19:12 sandboxd iMac - 5 K [133] ([465]): writeconfig (465) political system: deny /Library/Keychains/System.keychain file-writing-untie

  So it seems to be a sandbox configuration problem?

  Keith

  What functional problem you have, if any? Log messages are not a problem in itself.

• Packaging of FDT on windows error when you add the Active Directory in the package contents

  Hello!

  Trying new tools of FDT 5.5 for Adobe AIR, so far so good but I just encountered a problem when you try to add an Active Directory package.

  I add the shape of directory the FDT-> FDT AIR properties of project-> BlackBerry-> content tab package properties

  I click on add a directory and add the path to my Active Directory. (My current directory is in D:\Users\Julien\Travail\SRC\FDT5-workspace\MonArc\bin\assets)

  I then run a debugging, and I get the following error:

  Start debugging package.
  Package failed!
  Package failed: 1
  Error: File or dir does not exist: D:\Users\Julien\Travail\SRC\FDT5-workspace\MonArc\D:\Users\Julien\Travail\SRC\FDT5-workspace\MonArc\bin\assets error: file or dir does not exist: D:\Users\Julien\Travail\SRC\FDT5-workspace\MonArc\D:\Users\Julien\Travail\SRC\FDT5-workspace\MonArc\bin\assets

  There is a bug filed in Jira of FDT: http://bugs.powerflasher.com/jira/browse/FDT-2739 go vote for ;-)

  I get only this error when packaging of BlackBerry app, iOS or Android, everything is fine, so I guess that maybe it's a bug in the BB Plugin for FDT...

  If anyone has experienced this problem and know a workaround solution?

  Thank you!

  Yay, this has been fixed in FDT 5.6!

• Remove 'default' text characters when you add the new object text (label)

  Is it possible to create a new text object without characters 'text' on the inside?

  In addition, when you convert a rectangle to the text object, you the characters 'text' on the inside. Can you do empty by default?

  Tarek

  Hi Tarek,

  The text object is defined in a Text.xfo file, on my system, it is under C:\Users\BR001\AppData\Roaming\Adobe\Designer\10.0\EN\Objects\Standard.

  You can find the location by looking at the properties of the Group of the library of Standard objects;

  

  You can also create your own widget, set it up on the design finds out how you want and right click then 'add to library' (option has moved, but that's what SS3).  But I don't think you can get your own ones will appear in the drop-down list when you try to convert objects.

  Bruce

• When you add the data to the host of the second store it wants to format storage

  I have two hosts ESXi 5.5, one is the main host who currently runs the set of virtual machine from this data store. I would add the data store to the host, but to do so is greyed out on the new server, and he wants I want to format the data store.

  UPDATE:

  I used this thread to solve: cannot add to ESXi host VMFS datastore

  More precisely:

  Try the following command

  #esxcfg - volume - l

  This should show the volume

  To constantly increase the volume, use esxcfg-volume - M followed of the UUID or volume name

  Thank you for looking, sorry to distract. I saw this thread when troubleshooting first. Good day to all!

  Post edited by: TH2

  What type of shared storage using you, and you haven't set up the presentation of the logic unit number for the second host in the same way that you did for the first host? Do you manage the host with vCenter Server, or if you use two autonomous host computers?

  André