Whenever I start my PC, a message appears, says another user using the same IP address. Is this a problem

Similar Questions

• Message came up with, "Windows has detected another computer with the same IP address on this netework."

  A message came that said, Windows detected another computer with the same IP address. "... or similar message to one, that could just be the functioning of the laptop for the wireless?

  MurrayJoe:

  > Mean someone has or may have access to my PC or laptop?

  You mentioned a wireless laptop. Do you get this message at home (when your laptop is in communication with your own wireless router), or that you get this message when in a public hotspot?

  If at home, then I would be not too concerned (what security options enabled in your home router?).

  If you get the message while using a public access point, this does not necessarily your computer has been hacked... but it is a warning that you should not ignore. In general, I would not go to any site that has my financial data, or any other sensitive data, a public hotspot. There are too many ways that a public hotspot may be compromised.

  Your original post said that "a message came that said, Windows detected another computer with the same IP address.

  There are several reasons this could happen... some innocent people and some not so innocent.

  If your network is configured for the most common way, then your router uses a feature called Dynamic Host Configuration Protocol (DHCP). You can read about DHCP here...

  http://en.Wikipedia.org/wiki/Dynamic_Host_Configuration_Protocol

  Basically, when a device on your home network needs an IP address, he asks your router and your router assigns an IP address... technically, "rents" the router address for a given period (one day). Once this period has elapsed, the device must 'renew lease'.

  DHCP stops you from the hassle of having to assign a static IP address to each device on your network and then don't forget to retrieve that meet if/when a device are removed from your network.

  Sometimes the process DHCP can be confused and assign the same address on multiple devices. If/when this happens, communication between devices on your home network may be confused. Windows is smart enough to detect that another device on your home network has the same address as the computer where Windows is currently running..., but Windows can not solve the problem.

  You can determine the IP address of the computer that is running Windows (and posted the message you saw)... by entering "ipconfig" (without the quotation marks) at a command line prompt. Then you can check the IP addresses of all devices on your network until you find the other devices with the same IP address. Then you could say either every device to get a new IP address of the router (or restart the device). Alternatively, you can try just stating the computer that is running Windows to get a new IP address (by first entering "ipconfig/release" then "ipconfig / renew" in the command-line invite him... all orders without the quotes).

  But since you said that you are not very tech savvy, my first suggestion was the easiest... just shut everything in your network, and then restart one at a time by starting with your ISP device, router, and other devices. If the problem persists after that, then more troubleshooting (as described in the previous paragraph) would be necessary.

  I hope this helps to clarify the issue for you. If you have any questions, please post them and I'll try to answer.

• Whenever I start my computer, a message appears: "error loading C:\WINDOWS\ufidehipen.dll. The specified module could not be found. Can't fix it!

  Whenever I start my computer, a message appears:

  "Error loading C;\WINDOWS\ufidehipen.dll the specified module is not found."

  Once the message is erased my computer works normally.  Ironically received a hoax call, claiming they were from Microsoft Support.  I did not claim.  Have security of Norton 360.  A run 'getcleaner' and ' getmalwarebytes.  A ran all the Microsoft diagnostic tools and still have the same problem.
  If anyone can help with a solution to my computer problem?

  Hi Caspwilson,

  Not answering all calls for support!

  Download CCleaner from www.piriform.com/ccleaner and scan your system.

  I hope this helps.

• When I try to delete some folders, an error message appears saying 'you need permission SYSTEM to make changes to this file.

  original title: require authorization of the SYSTEM

  I decided to do a clean install of the latest Windows 7 RC yesterday and today crossed and have started to remove some programs on a separate hard drive so I could reinstall their own.  However when I try to delete some folders, an error message appears saying 'you need permission SYSTEM to make changes to this file.  I am using an administrator account, but I can't just simply delete the file.  I tried going to and change the owner to my account or administrators, close it, change the security permissions to allow me to have full control, and then I can finally remove it.  The problem is, I have to do for all the files one by one in the folder, and I wonder if there is an easier way to go about this, or if I can access the user of this SYSTEM and just delete them all from there.  Thanks for the help.

  Hello

  Not trying to resurrect the old discussions, but I'll answer anyway because this thread came on top of the list of search results when I searched for "you need permission to the SYSTEM; I hope this will help everyone.

  Note: here, "the record" as a subject refers to the folder that you want to remove.

  Step 1: Go to the built-in Administrator account, you can do so by following these steps:
  a. go to control panel > system and security > administrative tools
  b. on the left panel, go to local users and groups > users. You should now see a list of users on your computer
  c. right click on the administrator account that appears in the list and select Properties
  d. uncheck "account is disabled" and confirm by pressing OK

  Step 2: Connect to your newly activated administrator account

  Step 3: Now, we start to configure the security settings that will allow you to remove this folder which was (perhaps) held by the SYSTEM:
  I'm going to make the assumption that you want to remove a folder and all its subfolders along
  a. right click on the folder
  b. go to the security on the top tab
  c. click on the Advanced button which is at the bottom

  : Step 4 the first part to configure security settings to set the owner of the folder:
  a. go to the owner on the top tab
  b. click the button change located downstairs
  c. There should be a list of accounts to choose to change the property, this is located under the label "of a change in ownership:'"
  (d) the entry 'Administrator (YOURCOMPUTERNAME\Administrator)' should be there; If this isn't the case, then add it to the list:
  -Click on the button "other users or groups...". "who's down
  -Under the label "enter the object name to select (examples):', there should be a text field you can type into it;" type in "Administrator" (without the quotes of course)
  -Click on the "Check names" button which is located on the right. 'Administrator (YOURCOMPUTERNAME\Administrator)' should now be there _For itself_; Well, if not, then you must remove the line that does not represent the administrator account that you are currently
  -Confirm by pressing OK; It will now appear on the list of accounts, you can choose from
  e. now, select 'Administrator (YOURCOMPUTERNAME\Administrator)' from this list
  f. check 'Replace the owner of subcontainers and objects' to propagate our change
  g. press OK to confirm. a message should now pop-up window, which says to re - open the properties. Do by pressing all the buttons OK see you

  Step 5: now that we have the owner of the folder, we still not done. There is one crucial step left which is to remove permissions inheritable:
  a. Repeat step 3 to learn to re - open properties and get to "Advanced security settings"
  b. go to the permissions on the top tab
  c. click on the button "Change permissions" which is down
  d. at the bottom, there should be 2 check boxes:
  -' Include the permissions that can be inherited from the parent to this object': deselect this. When you do so, you will get a warning on the parameters of parent is not not able to spread. Select 'Add '.
  -' Replace all permissions of child object with permissions inheritable this object': check this
  e. press OK to confirm. Windows will warn you this time; Click OK
  f. reconfirm by pressing OK; now, you should get to properties again

  Now, you shouldn't have all the warnings about the SYSTEM do give you permission as he attempted to perform actions on this issue.
  All the boxes to change the permissions on the accounts (properties > Security > Edit) must now be enabled, and you can tinker around with it.

• Why am getting started on the internet with the message saying that more than one computer using the same ip address

  am is started from the internet for 3 days pass with the message saying that more than one computer using the same ip address

  am is started from the internet for 3 days pass with the message saying that more than one computer using the same ip address

  Thatmessage normally means a another computer on your local network has the same IP as the computer you are on.

  You control your Local network?

• Windows 7 - error message from the address conflict IP appears periodically. Error message "another computer on the network has the same IP address as this computer.

  Error message "another computer on the network has the same IP address as this computer. Contact you network administrator for help resolving this issue. More details are available in the Windows system event log"

  Does anyone have a simple way (for a dummy) to solve this. If I disconnect my wireless router and laptop and turn the two again this sorts the problem temporarily, but it does not provide a definitive solution.  I use a new laptop and my old one has been scrapped, so I do not know whence this 'conflict '.  My old laptop had Windows XP operating system and my new Windows 7.  I hope that someone can provide a solution to this annoying problem.

  Hi Figgerty,

  have you tried these steps?

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/IP-conflict-error-another-computer-on-this-network/4eed87e2-45FD-4FF7-ae29-9a9fb664a8cc

  B Eddie

• I get a popup message on my computer saying that another computer has the same IP address as mine.

  original title: address Ip issues

  What should I do or what it means when a warning is displayed on my laptop saying that this computer has the IP as another device?

  This means that there is another computer/device on your local network with the same IP as your PC. Try to configure your network adapter to use DHCP, or just give it an IP address different yourself... most LANs are minimal and you shouldn't have a hard time to randomly select another IP.

• Whenever I turn my laptop on, it flashes with a blue message appearing saying "your PC came across a problem..." »

  I have a hp laptop with Windows 8.

  Whenever I turn my laptop on, it flashes with a blue message appearing saying "your PC came across a problem..." »

  I tried repeatedly pressing f8 as soon as I start my pc, however nothing appears when I try this.

  Is that what I can do to fix this?

  Original title: System Restore

  Hello

  Check with the help of HP, their online documentation and drivers, diagnostics and ask
  in their forums on known problems.

  HP support/troubleshooting & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  =========================

  In 'some' case will help this article.

  Crashes Windows or freezes
  http://support.Microsoft.com/kb/2681286

  Do not forget to check with support of system manufacturer (manufacturer of motherboard for custom
  online systems), their resources and the drivers and ask in their forums (if any)
  on known problems. Don't forget to update BIOS, drivers of low level chipset,
  and the other pilots of major on-board and separate devices. Those who alone can
  set all or part of these issues.

  Note the use of Win Key + X and Win Key + W (to go on the Control Panel, Run and parameters
  According to needs). Win + D key calls the office and using Win Key active / disable the Office
  and the splash screen.

  Translate Windows 7 methods and use them on Windows 8.

  Resolution of the blue screen in Windows 8/8.1 errors
  http://Windows.Microsoft.com/en-CA/Windows-8/resolve-Windows-blue-screen-errors

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or can not
  Start Windows (applies to Windows 8). If you cannot start Windows 8 try using a repair
  Disc (see methods of doing a below) to access Mode without failure and other troubleshooting
  steps.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other) (applies to Windows 8).

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  (also, Windows 7 and Windows 8)
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  ===========================================================

  Check out these utilities to see if information may be collected:

  It is an excellent tool for displaying the blue screen error information

  -Free - BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table.
  http://www.NirSoft.NET/utils/blue_screen_view.html

  -------------

  MyEventViewer can be verified at the time of the blue screen (BSOD) to in a
  second or so time of the BSOD to provide more information as possible
  cause: see TIP.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it for a bit before and after the time of the BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ------------

  AppCrashView - free - a small utility for Windows Vista and Windows 7 which shows the
  Details of all application crashes occurred in your system. The information of the plant are extracted
  the .wer files created by the Windows Error Reporting (WER) of exploitation component
  system each time that an accident has occurred. AppCrashView also allows you to easily record the
  list of accidents to the text/html/csv/xml file.
  http://www.NirSoft.NET/utils/app_crash_view.html

  ===========================================================

  Windows 8 includes special discount methods (keep files and settings) or a reset
  (new installation remove all).

  How to restore, refresh or reset your PC
  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  How to create a system image to refresh your PC in Windows 8
  http://support.Microsoft.com/kb/2748351

  How to update Windows 8
  http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

  How to reset Windows 8
  http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

  If you have need of a system repair disc or other methods:

  How to create a "system repair disc" (CD/DVD) in Windows 8
  http://www.eightforums.com/tutorials/2855-system-repair-disc-create-Windows-8-a.html

  How to create a recovery USB in Windows 8

  http://www.eightforums.com/tutorials/5132-recovery-drive-create-USB-flash-drive-Windows-8-a.html

  How to start on the "System Recovery Options" in Windows 8
  http://www.eightforums.com/tutorials/2269-system-recovery-options-boot-Windows-8-a.html

  Boot to the tip "Startup parameters" in Windows 8
  http://www.eightforums.com/tutorials/4924-advanced-startup-settings-boot-Windows-8-a.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I tried all day offer of 10 image and the command of Adobe stock. Whenever I tried it, an error message appears.

  I tried all day offer of 10 image and the command of Adobe stock. Whenever I tried it, an error message appears.

  Could you please re - enter your payment details in the account management page, save it and try again.

  Please let us know if you continue to have problems.

  Thank you

  Bev

• When I go on the site of adobe and then try to download the software, a message appears saying that safari can't open a page that starts with "Mao."

  I bought a subscription to a cloud creative adobe Photoshop and Lightroom. When I go on the site of adobe and then try to download the software, a message appears saying that safari can't open a page that starts with "Mao."

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

• Message appear conflict of IP address at startup. Another computer already uses the network with the same IP address. How do I cure this?

  When my kids play online on the X - Box I get an error message on my laptop when I start after them. It is said there is an IP address conflict and that another device is already on the network with the same IP address. It does not affect me access internet even if. How can I fix thi.

  Hello

  1. which is the version of Windows installed on the computer? For example, Windows 7, Vista

  2. only the error message appears only when the Xbox is connected to the computer or at both times?

  3. have you made any software or changes to the material on the computer before this problem?

  Please answer these questions and provide additional information so that we can better guide you.

• When I try to download or install anything, a message appears saying that my Windows Installer is not correctly installed.

  1. Hi, I searched high and low for the answers! I searched all over the internet
     ten hours!
  2. I'm having a problem with my windows install!
  3. Everytime I try to download or install anything a message appears saying that my installer was not installed correctly?
  4. I had my computer for 5 years and have not had a problem like this happen!
  5. I tried the start menu then pressed the guest who took me to the black screen, I then typed in the cod for the Msi and I then pressed on enter and nothing came?
  6. But I know that there is something wrong with my installer because when I try to download or install something that to happen (but, when I press the run button, nothing happens?) I do not know???
  7. Can someone please! I have Windows Vista Home Premium 32 bit! Thank you
  original title: Hi, I searched high and low for the answers! I searched all over the internet!

  1. Hi, I searched high and low for the answers! I searched all over the internet
     ten hours!
  2. I'm having a problem with my windows install!
  3. Everytime I try to download or install anything a message appears saying that my installer was not installed correctly?
  4. I had my computer for 5 years and have not had a problem like this happen!
  5. I tried the start menu then pressed the guest who took me to the black screen, I then typed in the cod for the Msi and I then pressed on enter and nothing came?
  6. But I know that there is something wrong with my installer because when I try to download or install something that to happen (but, when I press the run button, nothing happens?) I do not know???
  7. Can someone please! I have Windows Vista Home Premium 32 bit! Thank you

  See this last answer of this forum:
  Note: ignore the itunes, the iphone part.
  The response is universal.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_programs/Vista-Windows-Installer-not-properly-installed/88a8171b-8c4c-42da-9702-0466aabd6862

• How do I keep my wifes calls appear on my phone and mine appear on hers, we share the same acct icloud and itunes? It just started this on one or two updates ago

  How do I keep my wifes calls appear on my phone and mine appear on hers, we share the same acct icloud and itunes? It just started this on one or two updates ago

  Welcome to the Apple community.

  I'm afraid that is what happens when you share an Apple ID.

  Ideally you should each have your own ID and use family share for share purchases, but at least you would be better to have your own ID's for everything except iTunes.

  I suspect that your problem is that you share an ID for FaceTime, you must either stop this or make sure that you have only and that your caller ID is only your phone number.

• When the BIOS on an IBM netvista starts you get a message that says "no operating system found"

  When the BIOS on an IBM netvista starts you get a message that says "no operating system found" press f1 to repeat boot sequence. but I need to change the boot sequence... Please help!

  Hello

  1. What is the operating system installed on your computer?

  2. don't you make changes to the computer before the show?

  Method 1:

  To change the boot order you must restart the computer and before you get the IBM logo on the screen start to type the F10 key to get the boot sequence menu.

  If you are not able to change the boot order by pressing the F10 key, please see the user manual to change the boot order.

  Method 2:

  Please see the links below.

  "Operating system not found" or "Missing operating system" error message when you start your Windows XP-based computer

  http://support.Microsoft.com/kb/321626

  No operating system is found when a Windows Vista-based computer is started, even if the computer worked correctly for a while

  http://support.Microsoft.com/kb/932932

• While the activation of Windows, the message appears "Windows already in use.

  all by activating the message window displays 'windows already in use', using my windows as I have origional CD bought with system of our company for what I work for. I formatted my system to speed it up, then I reinstalled vista. but upon activation, the message appears. So please discuss the issue as soon as POSSIBLE because I have to do an important job.

  * original title - theft of my windows vista key *.

  Use the phone activation