Which alerts must be configured in vROps to avoid the VM paging or Exchange?

Similar Questions

• Cannot save the Management Pack Configuration in VROPS

  Hello

  We started to experience a strange problem with our new VROPS 6.1 deployment when you try to configure certain management packs.

  We have 3 VrOPs devices deployed, Master, Master Replica and collector remote monitoring 3 standard vSphere (2 vRealize and a NSX) deployed using VMware cluster more practices and are working well. We had some problems with our vSAN where we lost a large amount of data because of a corrupted data store which meant losing our vCenter cluster Resource and Management 2 devices. Our vROPS / /vRA of the PSC devices / instances were fine as they were running on other storage. We had to re-bulid our vCenter but now have everything back running as expected.

  However... We started to add the vRA and SCOM management packs in vROPS which works well and sets up very well... but then something strange happening after about 5 minutes of data collection... the Configuration of each of the vRA and adapters SCOM disappears... And data collection stops. For more visit, it seems that someone has gone and remove the configuration of the adapter, but this isn't the case, because no one else has access to this environment.

  In any case, now when we try to re - configure an instance / configuration of an adapter we can not save the configuration of the card after we successfully test the connection we get this strange message that I have attached a screenshot in this post.

  The message reads the following:

  1. Unable to create the resource to HAVE it. Resource with the same key already exists.

  We have tried to remove the packs management, PAK re - install and replace the existing, but it does not work we always get the same error when trying to save.

  We are not now able to save the configuration of the vRA or SCOM adapters... and I'm a bit puzzled. Any help would be greatly appreciated.

  Hello

  I had similar problem. Which user are you logged as? There is a problem with the user rights and management packs. Only the local administrator users must be used, try to connect to this account and see if your configuration is not there already (such as msg of error States).

• Windows says FireFox must be updated but cannot be because the two instances are running, which is not true. It happens everytime I open FireFox

  Windows says FireFox must be updated but cannot be because the two instances are running, which is not true. It happens everytime I open FireFox

  This has happened

  Each time Firefox opened

  == June 28 2010

  Firefox 3.6.6 came out on 26/06/2010 to solve problems that some were plagued with the new crash protection feature introduced in Firefox 3.6.4. NOTE: Version 3.6.5 has been used for another product, so there is a "jump" in the version numbers.

  You need to update to the latest version, Firefox 3.6.6.

• which application should I configure on my ipad airprint

  Which application should I configure airprint on my iPad? The Epson printer is capable according to their literature airprint.

  jgl1429,

  It is a forum of the iMac, would you like that your post moved to a forum iPad?

• GUID value for 14.4 TMS must be configured on F5.

  How get the 14.4 TMS GUID value must be configured on F5. 14.4 TMS upgrade guide, the value of the GUID of the TMS must be entered in the string to send to probe.

  #CREATE MONITOR for TMS KEEPALIVE THE GUID IS FOUND in TMS GUI tmsh create ltm monitor https mn-TMS-HTTPS {DEFAULT cipherlist: + SHA: + 3DES: + kEDH compatibility enabled by default - https destination *: 443 interval 5 past drifting recv 200 recv - disable 503 send "HEAD /tms/public/IsAlive.aspx/? '} {"Guid =\\r\\n" time - until line-up 0 timeout 16 username 'DOMAIN\rname'}

  Are you referring to a redundant deployment of TMS?

  If so, take a look at page 31 under the section "Configuring network load balancing."

  You will find the URL Probe in TMS with a specific GUID to this knot here:
  Administrative Tools > TMS Server Maintenance > TMS redundancy > probe URL

• Standby redo logs must be configured on the primary

  Oracle 11.2.0.4, 4 CARS on primary node

  Oracle 11.2.0.4, node 4 CARS waiting

  Configured with oracle Data Guard using Data Guard Broker

  I use the latest version or orachk 12.1.0.2.4

  In the orachk report, I see the following error message:

  Standby redo logs must be configured on the primary

  +RECO/finprd1/onlinelog/group_13.2146.881183157

  +RECO/finprd1/onlinelog/group_14.2143.881183159

  +RECO/finprd1/onlinelog/group_15.5008.881183161

  +Data/finprd1/onlinelog/group_16.1660.881183161

  +RECO/finprd1/onlinelog/group_16.5003.881183161

  +RECO/finprd1/onlinelog/group_17.4999.881183163

  +RECO/finprd1/onlinelog/group_18.2096.881183163

  +RECO/finprd1/onlinelog/group_19.2094.881183305

  +RECO/finprd1/onlinelog/group_20.1778.881183305

  +RECO/finprd1/onlinelog/group_21.4994.881183307

  +RECO/finprd1/onlinelog/group_22.4992.881183307

  +RECO/finprd1/onlinelog/group_23.2049.881183307

  +RECO/finprd1/onlinelog/group_24.1454.881183309

  +RECO/finprd1/onlinelog/group_25.4983.881183309

  +RECO/finprd1/onlinelog/group_26.1688.881183309

  +RECO/finprd1/onlinelog/group_27.4973.881183311

  +RECO/finprd1/onlinelog/group_28.4969.881183311

  But when I check the primary database, I see that there are waiting for redo logs. So, why the error? Any ideas?

  [SYS@FINPRD11] SQL > select

  2 lg.group #.

  LG.type,

  3 4 lg.member

  l.bytes/1024/1024 as SIZE_MB

  Of

  5 6 7 v$ logfile lg,.

  v 8 $log l

  9 where

  10 lg.group #= l.group #.

  Union of all the

  11 12 select

  LG.Group # 13,

  LG.type 14,

  15 lg.member,

  16 st.bytes/1024/1024 as SIZE_MB

  17 of

  18 v$ logfile lg,.

  19 v$ standby_log st

  where the 20

  21 lg.group #= st.group #;

  GROUP # TYPE MEMBER SIZE_MB

  ---------- ------- -------------------------------------------------- ----------

  1 +DATA/finprd1/onlinelog/group_1.286.876507139 on LINE 512

  1 +RECO/finprd1/onlinelog/group_1.706.876507139 on LINE 512

  +DATA/finprd1/onlinelog/group_2.384.876507141 online 2 512

  +RECO/finprd1/onlinelog/group_2.737.876507141 online 2 512

  +DATA/finprd1/onlinelog/group_7.451.876507495 online 7 512

  +RECO/finprd1/onlinelog/group_7.714.876507497 online 7 512

  +DATA/finprd1/onlinelog/group_8.450.876507497 online 8 512

  +RECO/finprd1/onlinelog/group_8.1162.876507497 online 8 512

  +DATA/finprd1/onlinelog/group_5.449.876507499 online 5 512

  +RECO/finprd1/onlinelog/group_5.355.876507499 online 5 512

  +DATA/finprd1/onlinelog/group_6.448.876507499 online 6 512

  +RECO/finprd1/onlinelog/group_6.818.876507501 online 6 512

  +DATA/finprd1/onlinelog/group_3.447.876507501 online 3 512

  +RECO/finprd1/onlinelog/group_3.1188.876507501 online 3 512

  4 +DATA/finprd1/onlinelog/group_4.446.876507503 on LINE 512

  4 +RECO/finprd1/onlinelog/group_4.385.876507503 on LINE 512

  +DATA/finprd1/onlinelog/group_9.1653.881182905 online 9 512

  +RECO/finprd1/onlinelog/group_9.5058.881182905 online 9 512

  +DATA/finprd1/onlinelog/group_10.1654.881182985 online 10 512

  +RECO/finprd1/onlinelog/group_10.2206.881182985 online 10 512

  +DATA/finprd1/onlinelog/group_11.1655.881182985 online 11 512

  +RECO/finprd1/onlinelog/group_11.2205.881182987 online 11 512

  +DATA/finprd1/onlinelog/group_12.1656.881182987 online 12 512

  +RECO/finprd1/onlinelog/group_12.5045.881182987 online 12 512

  +RECO/finprd1/onlinelog/group_13.2146.881183157 EVE 13 512

  +RECO/finprd1/onlinelog/group_14.2143.881183159 EVE 14 512

  +RECO/finprd1/onlinelog/group_15.5008.881183161 EVE 15 512

  +DATA/finprd1/onlinelog/group_16.1660.881183161 EVE 16 512

  +RECO/finprd1/onlinelog/group_16.5003.881183161 EVE 16 512

  +RECO/finprd1/onlinelog/group_17.4999.881183163 EVE 17 512

  +RECO/finprd1/onlinelog/group_18.2096.881183163 EVE 18 512

  +RECO/finprd1/onlinelog/group_19.2094.881183305 standby 19 512

  +RECO/finprd1/onlinelog/group_20.1778.881183305 EVE 20 512

  +RECO/finprd1/onlinelog/group_21.4994.881183307 EVE 21 512

  22 +RECO/finprd1/onlinelog/group_22.4992.881183307 ENSURES 512

  +RECO/finprd1/onlinelog/group_23.2049.881183307 EVE 23 512

  +RECO/finprd1/onlinelog/group_24.1454.881183309 EVE 24 512

  +RECO/finprd1/onlinelog/group_25.4983.881183309 EVE 25 512

  26 +RECO/finprd1/onlinelog/group_26.1688.881183309 ENSURES 512

  +RECO/finprd1/onlinelog/group_27.4973.881183311 EVE 27 512

  +RECO/finprd1/onlinelog/group_28.4969.881183311 EVE 28 512

  41 selected lines.

  [SYS@FINPRD11] SQL > SELECT GROUP #, THREAD #, SEQUENCE #, ARCHIVED, STATUS FROM V$ STANDBY_LOG

  2;

  GROUP # THREAD # SEQUENCE # ARC STATUS

  ---------- ---------- ---------- --- ----------

  13 1 0 UNASSIGNED YES

  14 1 0 UNASSIGNED YES

  15 1 0 UNASSIGNED YES

  16 1 0 UNASSIGNED YES

  17 2 0 UNASSIGNED YES

  18 2 0 UNASSIGNED YES

  19 2 0 UNASSIGNED YES

  20 2 UNASSIGNED YES 0

  21 3 0 UNASSIGNED YES

  22 3 0 UNASSIGNED YES

  23 3 0 UNASSIGNED YES

  GROUP # THREAD # SEQUENCE # ARC STATUS

  ---------- ---------- ---------- --- ----------

  24 3 0 UNASSIGNED YES

  25 4 0 UNASSIGNED YES

  26 4 0 UNASSIGNED YES

  27 4 0 UNASSIGNED YES

  28 4 0 UNASSIGNED YES

  IT would be difficult to debug, better you trigger SR in support to verify the code. Good thing is you know again sleep exists, so why worry.

  You can ignore it.

• Can (must) I apply all current patches to the newly installed instance of EMP 11.1.2.1 release before you start to configure it?

  Can (must) I apply all current patches to the newly installed instance of EMP 11.1.2.1 release before you start to configure it?

  Hello

  First, you configure the new instance and check if it works well. Then apply patches, following the patch readme. Patches usually does not require a full configuration.

  Thank you

  KK

  ~ Mark answer if its helpful.

• 12511 suddenly received alert TLS; treat it as a rejection by the customer

  ISE Version: 1.2.0.899 (running in VMware)

  WLC: 5508 worm 7.6.100.0

  I have a created WLAN using the dot1x authentication. The WLAN points at ISE for RADIUS AAA. I can't get any windows computer connect (7, 8 or 8.1 tested), but android, ios, and osx are all able to connect. I have a 3rd cert of party (GoDaddy) installed in my local store at ISE, which is valid and not expired. I do not understand why windows machines fail.

  I'm migrating to this new ISE server and my old ISE server has the same configuration (AFAIK) for this WLAN key and it works for all devices, including windows. The difference is that it is on a different domain (the reason for migration is we've changed areas).

  Here the ISE error:

  Event: 5400 authentication failed

  Reason for the failure: 12511 suddenly received alert TLS; treat it as a rejection by the customer

  Resolution: Ensure that the ISE server certificate is approved by the customer, by configuring the supplicant with the CA that signed the certificate of ISE server. It is strongly recommended that you not turn off the server on the client certificate validation!

  Root cause: while trying to negotiate a TLS negotiation with the customer, ISE has received an unexpected alert message of TLS. This could be due to begging her not to trust the certificate of the ISE server for some reason any. ISE has processed the unexpected message as a sign that the client has rejected the creation of tunnel.

  Here is the error WLC:

  Authentication failure AAA for UserName:Domain\User user Type: USER WLAN

  Here's the windows event viewer error:

  Source: Microsoft-Windows-security-auditing
  Event ID: 5632

  Description:
  A request has been made to authenticate on a wireless network.

  Object:
  Security ID: NULL
  Account name: user
  Account domain: domain

  Network information:
  Name (SSID): IT-Test

  Additional information:
  Reason code: Eap explicit received failed (0 x 50005)
  Error code: 0 x 80420014
  EAP reason code: 0 x 80420100
  EAP Root Cause string: user certificate failed\nThe of network authentication required for the network was not found on this computer.

  EAP error code: 0 x 80420014

  On the ISE server that works, you are presented with a window asking you to connect or terminate based on the certificate is not validated. I don't know why that is not happening with this new ISE server, it fails just without inviting the user to connect or terminate. Two certificates are of GoDaddy.

  A difference between the certificates, is the former has a cert that was generated through ISE and the new server has a generic cert imported.

  In any case, I hope this is enough information to understand the issue. I appreciate the time everyone takes to help me with this problem. I install a copy of the WLAN so that I can test the need and not have to wait for a maintenance window.

  Some endpoint devices (Windows OS) have problems with generic cert when CN contains * (start) as wildcard
  >
  > PEAP authentication fails due to "12511 received unexpectedly alert TLS; treat it as a rejection by the customer.
  >

  > Conditions:
  > what contains the wildcard certificate * (start) as a wildcard in the CN
  >
  > Workaround:
  >
  > create generic with * (start)
  > for example CN = aaa.cisco.com

• WPA2-Personal wireless network, which is not yet in wireless networks accessible to the general public?

  Original title: lost our connection to network WPA2-Personal wireless internet which is not even listed as an option to connect to the internet, how do solve us this problem?

  Our WPA2-Personal wireless network fails to connect to the Internet and not yet in the available networks? Is this a problem with the adapter or modem (Cox)? And how to fix this? Help!

  Hello

  Check with the manufacturer of your router Support and Forums. If the router is configured to not show

  the SSID, then it will not appear in the available list. Maybe the router must be
  reset.

  Log in to hidden networks configuration of the control panel - network and sharing Center - a
  new connection or network.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• How can I configure numerical Lock ON when the computer starts?

  I have a new laptop HP G70.  In the User Guide HP G70 on keyboards - C01540939.pdf, paragraph 3 using keyboards & pointing devices, Page 8 there is a note "the function of the keyboard that is active when the computer is turned off is restored when the computer turns on.   This does not work on my computer HP G70.  It always starts up the number Lock OFF.   How can I configure my computer to set the digit Lock ON when the computer starts?  I always use the number keypad and never use page up/down - button on top/bottom/right/lelt arrow.

  Also, how can I configure my computer to set the touch mouse on the computer OFF for the start.  I always use an external mouse.

  Any help would be appreciated.  It is a simple thing, but the present operation HP G70 is most annoying.

  PLEASE DO NOT CONTINUE TO MEET THIS PROBLEM!

  THE HP G70 WAS FAULTY!   EACH HP G70 HAS THIS PROBLEM!

  HP REPLACED MY HP G70 WITH a HPdv7.  THE HPdv7 PERFORMED THE DESCRIBER NERMAU LOCK FUNCTION AS IN THE HP INCTRUCTIONS.

  .
  
  Bob_in_PGI

  I'm surprised that nobody knows how to set the Num Lock at startup before you connect.  Where is the help of HP?

  I now have Windows 7 64 bit.

  There must be someone who knows how to do this.

  Bob in PGI

• HDD and dvd are not recognized in the configuration menu, what could be the problem?

  The hard drive and dvd drive are not recognized on the configuration menu for my desktop Pavilion a4316f.  What is a controller failure?  A PCI controller can be used to replace the motherboard controller?

  dhobs,

  Anguish, that the suffering of the faulty motherboard has been aggravated by your actions. Why you decided to perform a restore (which re - formate the disk, erase all your data files (documents, photos, videos to misic,) is really amazing.)

  You had a viable BONE, work and the data store. You he clobbered with recovery. As explained, the 'tattoo' reads the embedded hardware configuration and will stop at the resumption of treatment if it detects a change.

  Only temporary help I can offer is to open the computer case and install a small 12v on the NVidia chip fan. IF the chip is not 100% burned, you can earn low enough time to reinstall the operating system and then add the map.

• Hi, while writing an email online using Firefox 3.6.3, I was using one of the "CTRL + left arrow or right" to move the cursor on the text. I must have pressed some other key because the screen has become huge - and I can't scroll vertically or horizont

  Hi, while writing an email online using Firefox 3.6.3, I was using one of the "CTRL + left arrow or right" to move the cursor on the text. I must have pressed some other key because the screen has become huge - and I can't scroll vertically or horizontally, which makes the pages of Mail of Hotmail impossible. I have connected since using the Explorer MSFT and it works very well. This problem occurs only on the page of Mail of Hotmail Live not on the home page or other.
  Could you please let me know if there is a problem with Firefox, or if you have any advice on how to restore the appearance of Hotmail in Firefox?

  This has happened

  Just once or twice

  == I'm compiling an email in Hotmail Live

  See this:
  https://support.Mozilla.com/en-us/KB/page+zoom

• My computer takes 9 minutes to start when you turn on. Where can I find the system configuration to abandon some of the start up programs that I don't need.

  I said the reason that my computer takes 9 to 15 minutes to complete the commissioning is there are too many programs that start automatically when I turn it on. They said to click on start and type system configuration and deselect some of the programs to start automatically. I typed in the run dialogue box but nothing.  How do I know where to find it and can you tell me which ones I should NEVER disable? Thank you.

  You type: msconfig in the Run dialog box.

  Under the Startup tab disable this you never or rarely use.

  You will always be able to use them whenever you want without going back to msconfig.

  On the Services tab, click Hide all Microsoft Services, and then choose the ones you want to start when you start your computer.

• Windows XP is stuck in a loop, saying it must be enabled. I never have the wizard or it never activates.

  Activation problem

  I had to 'fix' a WinXP installation. Now I'm stuck in a loop, saying it must be enabled. I never have the wizard or it never activates. What should I do?

  It is same in 'safe mode' (I think that CTRL + ALT + DELETE)? Can you try to connect as administrator account (this account must be in "safe mode" and his name is administrator)

  If it the same - next you can try - press F8 during boot and in the menu select ' last good known Configuration":

  http://support.Microsoft.com/kb/307852/en

  LC

• Roxio Creator 2010 gets error "Setup has determined that your configuration does support all of the included products."

  I have Vistia based home Addition.  I bought Roxio Creator 2010 & when I try to install it, I get "Setup a fix6 that your configuration does support all of the included products."

  I have Vistia based home Addition.  I bought Roxio Creator 2010 & when I try to install it, I get "Setup a fix6 that your configuration does support all of the included products."

  You must have Windows Service Pack 1 installed or no Roxio.

  http://buysoftwarelicense.NET/shop/item/398/?CPN=www_montyroberts_com
  Scroll to system requirements.

  t-4-2