Re: Tecra S11: two questions - No. WiFi and USB number after sleep

Similar Questions

• Tecra S11 - bluescreen when the WiFi switch is on

  I've known several accidents suddenly blue screen, with apparently no advice. After several tests of different conditions I counted it takes place when the WiFi switch is on. So, it should be associated with Bluetooth or WiFi.

  Any suggestions how to proceed further? apparently I have the latest drivers (Windows 7 64)
  Thanks, Guido

  Hey Buddy,

  Have you already checked the BIOS if you have installed the latest version? If this is not the case check this on the Web from Toshiba site and make an update of the BIOS. Maybe it helps

  But I had a similar problem last year and the solution was exchanging the WLAN card.

  I think your Tecra S11 should still be under warranty and in this case that the repair will be free. :)

• Re: Tecra S11 - Dual boot Windows 7 and XP

  I installed Windows 7 (from the hidden to the hardrive recovery section) on my new Tecra S11. I would like to know if I can use the Windows XP
  recovery media provided by Toshiba to create a dual boot Windows 7/Windows XP rather than go back to XP?

  Hi dualboot.

  As far as I know it of not possible to create a dual boot with XP and Windows 7 Toshiba Recovery disk. The problem is that the recovery disk erases the entire HARD disk, so there is no option to create a dual boot with another operating system.

  If you want XP too you need to a normal XP installation disk Microsoft or you use virtualization of Windows 7 XP mode, if some n t applications run on Windows 7. ;)

• Two questions about SP1 and Vista startup

  Hi all
  two questions:

  (1) I understand that if I want SP1 on my machine, I have to install manually, because it is not included in the automatic update routines?

  (2) my machine failed yesterday, I received a message "unable to start Windows. A recent hardware of software change might be the cause. "The only thing I can think is that before turning off the previous time, I inserted a USB hard drive to copy the files on it. But I continued to work normally on the machine. Another unusual event, it is the day before, it was very slow to start, so afer it finished start, I restarted.

  When the system could not start, I tried several times, automatic procedures that always ended with "windows cannot resolve the issue automatically,
  Contact your service provider. In the last attack, I also clicked on a 'Advanced tab' and restored the system, but it does not solve the problem. Then, this morning I turned on the machine again to write the exact error I have, and message instead, unexpectedly (and rather willingly), the machine starts normally. So, what could happen? Should I get my machine (which is less than one month) verified?
  Thank you!

  Paola

  Hi polla.

  (1) Yes, Yes. You must download and install SP1 manually.

  (2) No, I'm Don t think that you should check. I would say: work with it and if the error appears, back up all your data and restore complete your system, so you can exclude any type of software problem...

  Welcome them

• Two questions about T440s and T540

  Hello

  Recently, I bought ThinkPad T540 and my father also got a T440s for his work. He asked me if there was a physical switch to WiFi and I have no idea. It wasn't a W510, is this feature removed on T540 and other models xx40?

  Another thing is the sleep button. Before that I was able to quickly put my computer to sleep with the key Fn + Sleep (rescent blue moon). I know there is no button with the same symbol, but in Lenovo Power Manager there is an option for the action of the "Sleep" button It is set to "sleep". My question - is there a "sleep button" after all? I am able to define a shortcut for sleep somehow outside the power button / stop hoding for 1 second?

  Yes, wifi switch has been removed in laptops Haswell. I think fn + 4 is now the sleep button (not F4!).

• Tecra S11-14 t - Windows is not go further after updates

  Hello
  Tecra S11-14 t
  Two times the same problem. Problem after installing updates Windows 7 x 64 d Description of the problem: after installing six update - restart windows - after entering the password to login as an administrator - I... Hmmm... does not further!
  Withdrawal of previous state wines - does not help, same problem. After that installation of the hidden partition on the HDD is ok, then instantiated windows update and again the same problem!
  I suspect that some sort of update is in conflict with a program of the factory. Technical Microsoft said there are no other entries with the same problem.

  How to check the update does it hurt? The method of manually select and install the update will last forever.

  Hi biuro,.

  Can you start the laptop in safe mode and connect to Windows? It would be important to know if works at least in safe mode or not.

  Is it so if you install Service Pack 1 for Windows 7 before I start with a few other Windows updates?

• USB ports not recognizing keyboard and the mouse after sleep

  I have a wireless Logitech and mouse keyboard. These connect to my PC (Vista32) wirelessly via a USB plug small heel I plug into a USB port. Logitech called "Unify" which, according to them, is standard to connect devices through a USB port. My mouse and keyboard work fine when I restart my computer, but when he goes to sleep and I me re - wake up there that they do not have. I force power off of my computer because I can't access my account.

  I have ensured that the selective suspend setting in settings usb in advance power settings is disabled. Support Logitech seem unable to help him.

  Hey Sinclair,

  You can refer to this link suggestions and answer us with the State of the question.

  A USB device may no longer work correctly when Windows Vista comes out of standby or hibernation

  http://support.Microsoft.com/kb/928631

  Also refer to this link: How to troubleshoot USB device problems that can occur after a PC that is running Windows 7 or Windows Vista from sleep or hibernation resume

  http://support.Microsoft.com/kb/953367

  Registry WARNING: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see this link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  I hope this helps.

• Two questions: Running XP and have some interesting questions at the start and with IE.

  Hi, I try to wear the IT hat and works to clear up some questions on my mother's computer.  #1 I guess that the computer was shipped with a version of Corel Photo software on it and we cannot get rid "Installer" messages at the beginning upward.  We tried to remove the program and the same message comes back to tell us that "Installer can do the requested action without the CD/program files" it gets about 6 of these reviews that it must close any until the computer will continue to boot the system.  Please, please tell me how to get rid of this.  I tried to install the 'Installer' update to see if that would make the difference and nope.  I also tried to remove the Corel file via CCleaner and got the same message.  I do not have the program disc, I don't want to program... I want to just get rid of it!

  #2 when entering address in the Internet Explorer address bar, the browser opens a second browser instead of going to the requested site.  For example, when I open my Internet Explorer and say go to the top of the address bar and typewww.google.com, instead of going to Google, it opens a completely separate browser.  When she did this, it's EXTREMELY SLOW!  until you think that IE went unresponsive and then finally opens the second browser.

  I'd appreciate any help!  I'm trying to solve these problems, while I'll be staying here so that I can leave him a computer running.

  Thank you!

  Hello

  ·        What version of Internet explorer that you are using (Internet Explorer 6, 7 or 8)?

  ·        Was long before Internet Explorer work?

  ·        Since when are you facing this problem?

  Step 1:

  It may be some third-party software that runs in the background that is shown with the process, I suggest you do a clean boot and check. To perform a clean boot follow the steps mentioned in the link given below.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: Once you have finished installing, follow step 7 to start the computer in normal startup.

  If the steps above don't help you not to remove the Corel Photo software, I suggest you to post your query on the forums of XP. Click on the link below.

  http://social.answers.Microsoft.com/forums/en-us/xpprograms/threads?filter=answered

  For Internet Explorer related issues, follow steps 2 and 3 of the step.

  Step 2:

  I suggest you run the fix it this tin article given to repair Internet explore

  How to reinstall or repair Internet Explorer in Windows Vista and Windows XP

  http://support.Microsoft.com/kb/318378

  Step 3:

  If you use Internet Explorer 7 or 8 I suggest you run the fix it is present in the article below. If you use Internet Explorer 6, you can follow the steps mentioned in the article given below where they apply to Internet Explorer 6 also.

  How to reset Internet Explorer settings

  http://support.Microsoft.com/kb/923737

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Two questions: Windows Vista and XP on HP a6130n

  A6130n HP from my father (AMD Athlon 64 X 2 dual processor running Windows Vista) had a hard drive crash. I replaced the HD and tried to recover using the recovery discs, he has created. He was suspended during the recovery process of system usually at about 3%. I have clean records and restarted several times without success. I was able to load Windows XP using my Windows XP disk, but many drivers do not seem to work (sound, network, etc.).

  Windows Vista is my next step to order the HP restore disc, or are there other options?

  Windows XP: My father has renounced this PC and gave it to me. I think I would have preferred XP. There is no drivers listed for this model for XP. Are there options with this route? Should what drivers I download?

  Thank you very much for your advice. Dave.

  Try MS UAA Hotfix, with a reboot after:

  http://www.mediafire.com/?4ben9zlesng

  If still no audio_Go here for the Realtek site, contract, then select High Definition Audio Codecs, then download the executable:

  http://tinyurl.com/6y55xn

  Message edited by CherylG on 07/03/2009 15:13

• Two questions about ASM and GR 11, 2 installation of the grid

  DB version: 11 GR 2
  Operating system: Sun Solaris
  
  1. in GR 11, 2, after the installation of network infrastructure, succesfull ASM instances starts automatically in all the nodes. Right?
  
  2. just after the end of the grid infrastructure installation, I tried to connect to the DSO. But I was invited for ORACLE_HOME rather than GRID_HOME. Why is this? ORACLE_HOME is the location of the client software of RDBMS. I started not to install some RDBMS again.

  $ ORACLE_SID=+ASM1
  $ export ORACLE_SID
  $ sqlplus / as sysasm
  sqlplus: not found
  $ /u03/grid/bin/sqlplus / as sysasm
  Error 6 initializing SQL*Plus
  SP2-0667: Message file sp1<lang>.msb not found
  SP2-0750: You may need to set ORACLE_HOME to your Oracle software directory 
  
  
  
  $ ORACLE_HOME=/u03/grid/
  $ export ORACLE_HOME
  $ /u03/grid/bin/sqlplus / as sysasm
  
  SQL*Plus: Release 11.2.0.2.0 Production on Thu Nov 11 15:20:16 2010
  
  Copyright (c) 1982, 2010, Oracle.  All rights reserved.
  
  Connected to an idle instance.

  Hi Garry,

  1. Yes, it should start automatically. You have defined all variables before you start the installation?

  2. the variable ORACLE_HOME must be set to the location of GRID_HOME for the user environment of GRID and the location of ORACLE_HOME for the oracle user.

  Kind regards.

• Poor wifi and Bluetooth connectivity after iOS 9.3.1

  9.3.1 IOS is installed on my iPhone 6 wifi in my house guard fall!

  My Bluetooth connectivity keeps cutting to work! So annoyin!

  General suggestions for Wi - Fi problems, maybe one of them will help you...

  (1) perform a forced reboot: hold the Home and Sleep/Wake buttons simultaneously for about 15-20 seconds, until the Apple logo appears. Leave the device to reboot.

  (2) resetting the network settings: settings > general > reset > reset network settings. Join the network again.

  (3) change of Google DNS: settings > Wi - Fi > click the network, delete all the numbers under DNS and enter 8.8.8.8 or otherwise 8.8.4.4

  (4) reboot router/Modem: unplug power for 2 minutes and reconnect. Update the Firmware on the router (support Web site of the manufacturer for a new FW check). Also try different bands (2.4 GHz and 5 GHz) and different bandwidths (recommended for 2.4 to 20 MHz bandwidth).

  (5) disable the prioritization of device on the router if this feature is available.

  (6) determine if other wireless network devices work well (other iOS devices, Mac, PC).

  (7) try the device on another network, i.e., neighbors, the public coffee house, etc.

  (8) to restore the device (ask for more details if you wish).

  https://support.Apple.com/en-us/HT201252

  (9) go to the Apple Store for the evaluation of the material.

• Questions about SD and USB running Vista on Satellite M40X

  Well, I've updated my M40X to VISTA, if it is not mentioned on the list of allow.
  Well, actually installed on a new formatted partition.
  Runs smoothly, RAM is sufficient, component more slow seems to be the CPU, well, fair enough.

  Obviously, I'm not able to get the card reader (chip SD card combo, xD,) or the USB ports running.
  The two is listed in Device Manager, the USB hub and the customer of the sd. In addition, there are a storage device mass with a pilot error in the list.
  Whenever I have insert well tested cards, USB HDs mp3 players or that it is in the slots the computer sometimes makes noise-ping but does not show any device in Solution Explorer or a new letter of the device.

  I think it's some kind of driver issue, but found no solution. Not even after researching dayandnight on forums and other things.
  Card reader is "Texas Instruments PCIxx21 Intergrated Flash Media Controller", as I understand it.
  Well, I'd be more than happy and greatfull if someone could recommend a solution for these problems, pref with links to the drivers.
  Am really low.

  TIA

  Jan

  Hello

  As you know, this laptop model is certainly not support Vista and Toshiba will design all the Vista drivers for this model of laptop. I can imagine that Vista works very well, but without the right drivers, it is not easy to use certain hardware components.

  I recommend you to use Windows XP Home edition. WXP works great on this laptop. For all tests, you can install Vista on the second partition to see how it works. I think right after a few weeks remove you Vista and use WXP as before. ;)

• Pavilion 15-p214dx: wifi and usb drivers

  Im working on a Pavilion Envy 15-p214dx for a friend and all ive found drivers aren't working on it. It is said that it contains a RTL8188EE of Radio Realtek. Anyone can bind the pilot OK for me please?

  Hello:

  You can use the W7 x 64 drivers and software of p000-15 t on this model, except for the BIOS and firmware files.

  http://support.HP.com/us-en/drivers/selfservice/HP-Pavilion-15-P000-notebook-PC-series/6936226/model/7174371

• Question about expdp and impdp number of tables in a schema 11.2.0.3

  Hello Experts-

  I have 145 tables of a certain pattern that I want to save for example export and import the same tables in another schema is possible?

  1. REMAP schema to use for this purpose?
  2. I must quote all 145 tables? or I can use '%' as all the tables I want export & import start with a certain word-(RECORDS_)?

  Thanks in advance

  Hi 885068,

  I have 145 tables of a schema of some I want to save for example export & import the same tables in another schema is possible?

  Yes, it is possible.

  REMAP schema to use for this purpose?

  Yes, it is the purpose of REMAP_SCHEMA. Import metadata and data from one schema to another.

  I must quote all 145 tables? or I can use '%' as all the tables I want to export & import begin with a certain word-(RECORDS_)?

  It's always better when you have total control of what you're doing. I prefer to put all the tables, of course it not easy, but you can use sql statements to generate the TABLES all = parameters you need like the following:

  SELECT 'TABLES='||table_name
  FROM all_tables
  WHERE owner = ''
    and table_name like 'RECORDS_%'
  ;
  

  In case of import, you need not specify that you must import because the entire dump contains the tables that you imported exported tables, but it is very advisable that you specify the tables.

  So if the tables in the target schema must be created with names different than the original, you must use the parameter REMAP_TABLE =.:

  HTH,

  Juan M

• Google Earth and camera running after sleep.

  I closed the lid on my Macbook Pro late 2013 to put to sleep and awoke to find Google Earth and my camera running. The only apps I leave but no open Windows Mail and Chrome. I saved my system log to a text file, but can not find to search. I didn't save all newspapers. Never had this happen before. Could I have malware? There is a lot of activity in the mode 'sleep'! I don't know if this is the best place to post - perhaps under El Capitan would have been better.

  georosejr wrote: I closed the lid on my end 2013 Macbook Pro to put to sleep and awoke to find Google Earth and my camera running...

  Check that your ... System Preferences > energy saver > annex > start or reactivate setting is off (no indicator check.)

  

  Also check the box wake for network access is not marked.

  Finally, make sure that the lock in this window is closed to avoid changes until you provide your administrator name and password.

  Do these three things should prevent anything using your Mac, until I YOU wake up from its sleep.

  georosejr wrote:... Could I have malware? ...

  If the problem persists even if your System... Preferences are configured correctly, it is possible.

  You can check for malware using Malwarebytes Anti-Malware for Mac.

  Post edited by: Jim EZ

  Mac OSX 10.11.4