Why not enough system resources?

Similar Questions

• Recently, I got a message saying ' not enough system resources to open the application' for example to explore or outlook express.

  ?? Resources

  My computer has been works well, but twice recently, I got a message saying ' not enough system resources to open the application' for example to explore or outlook express. Restarting it works again, but why the message?

  Hi RaymondWilson,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click restart to restart the computer.

  Method 2: Perform a System Restore and check the issue persists.

• Not enough system resources to complete the task

  REF Dell Desctop PC Windows XP SP 3... GB 74.4 Mem WITHOUT 24.9 en

  Recently, because of the new connection by the web... WITHOUT ANTIVIRUS SOFTWARE? PC became badly infected. PC did not close down in normal mode. Necessary to deactivate the tower. "When you turn off the screen" erased "rather"disappear"as usual.

  Bought McAfee Total Protection and tried to install... not possible. Downloaded 'Stinger' USB transferred to the office and ran the program in Mode.REport security, apparently cleaned files, including RIMECUDE. GEN.b virus. Don't go back to the normal log in, Sun software McAfee tried again... no use. Attempted to find and run the PC recovery and "not enough...". "appeared. Same message when you try to open a number of applications... Currently have no connection to the web

  Could someone please advise...? Thank you very much... Darcy

  REF Dell Desctop PC Windows XP SP 3... GB 74.4 Mem WITHOUT 24.9 en

  Recently, because of the new connection by the web... WITHOUT ANTIVIRUS SOFTWARE? PC became badly infected. PC did not close down in normal mode. Necessary to deactivate the tower. "When you turn off the screen" erased "rather"disappear"as usual.

  Bought McAfee Total Protection and tried to install... not possible. Downloaded 'Stinger' USB transferred to the office and ran the program in Mode.REport security, apparently cleaned files, including RIMECUDE. GEN.b virus. Don't go back to the normal log in, Sun software McAfee tried again... no use. Attempted to find and run the PC recovery and "not enough...". "appeared. Same message when you try to open a number of applications... Currently have no connection to the web

  Could someone please advise...? Thank you very much... Darcy

  The usual advice when a computer has been infected after that connect to the Internet with no antivirus application is to do a clean installation of Windows.

  Computers Dell come with a mechanism to restore the computer to its costs-Dell-State.  I don't know if that's what you mean by 'Attempt to find and run the PC recovery', but you will find the information here:http://support.dell.com/support/topics/global.aspx/support/dsn/en/document?docid=181316

  If you follow the advice of Dell to backup your data before you run the restore program (and that you are able to do), do NOT restore these data before (a) install an antivirus on the restored computer application and (b) using the application antivirus to analyze the data before you restore.  If you have data that you do not want to lose, but you can not run the backup offered by Dell, there are always methods to get your data off.  Select if you want instructions for it.

  If you can, return McAfee Total Protection for a refund.  If you can not get a refund, write off the expense as a learning experience.  Once your computer has been restored, installNOD32 Antivirus 4 (not the "suite") from ESET.com if you want a commercial product.  If you do not want to pay, installMicrosoft Security Essentialsor Avast! antivirus .  In more than one of these 3 antivirus applications, download and install these two applications free anti-malware: Malwarebytes Anti-Malware and SUPERAntiSpyware .

• Halo 2 Failed installation - "failed to initialize. Not enough system resources were found to ruin the game, or game data are missing or damaged. Reinstall the game may fix this problem. » ____

  I check the system configuration required and everything seems OK.  The only thing that is not the same is the video card.  The video card in the PC, I am installing on is an Intel (R) G33/31 Express Chipset Family 286 MB and not the ATIX700 or Nvidia 6100 128 MB.  This will stop the installation of the game or is this something else.  I tried to reinstall and also installation on another PC, but it happens with the same message that makes me think this is the game.  Does anyone have any suggestions?

  ------------

• Error UCSM Serive Profill [not enough vNIC, connection-investment, not enough global resources]

  Hi guys,.

  I work in Cisco, and we have a problem for a few days, so I thought it would be useful to ask here.

  We created the service with 3 vNIC profile and tried to associate it with a server [actually, we tried 4 different servers] and always, the error we get is:

  "not enough vNIC.

  connection-investment

  There's not enough global resources. "

  Once I realized the error code is F0327, but not always.

  I suspect it's something with the IO Module or do not know what?

  Please, can anyone help?

  Thanks in advance,

  Ron

  Hi guys,.

  I just wanted to post this for everyone else reference.

  Blade: B200 M1

  Adapter: Cisco UCS M71KR.-e.

  3 VNIC was applied. Two NICs FOR interconnection fabric A and b. interconnection 1 VNIC to the tissue that was a fail with the error "connection placement. This is due to the fact that this card is part of the series of Menlo, in which physical network adapters are mapped to left and right that they can't stand to not "allow failover. This is due to the hard Menlo being mapped to each fabric interconnect so that would mean a VNIC / VHBA by the interconnection fabric.

  Once this has been corrected this error disappeared and the association of service profile is complete.

  Kind regards

  Qiese Sa'di

• After Effects and Media Encoder do not use system resources!

  Hi all.

  I have a small problem with the AE and me. None of them use all the resources of my computer.

  I have 8 GB (2 * 4 GB) of RAM and an Intel i5 - 2500 K CPU.

  When rendering previews, AE takes forever to load the clip (about a second image every 10 seconds). When rendering (encoding) clips inside of ME and AE, everything is extremely slow. This only happens when I'm making large compositions, or using pre-made (and very large) model effects.

  Course of the coding, AE / ME use about 50% of the CPU and RAM, instead of the full capacity. Surely they would be better if the use of the full system resources?

  I even tried setting the priorities of processes for AE and ME "Very urgent", but this doesn't make much difference.

  AE already has 39 GB of space available for the cache, preview is disabled during the encoding in me. I gave them as much RAM in their respective preferences, but this makes no difference. I understand that the programs will be a bit slow when the compositions of work with high calibre, but they do not even use as much capacity is available on the system.

  I take a little over an hour to encode 30 seconds a clip.

  I hope you can help - much thanks in advance.

  -phoenix

  PS the two pieces of software is CS5.5

  Nothing to correct because nothing is broken. The programs wil ltake what they need and not beyond that, or more specifically, what are their internal infrastructure can be used. Many encoding jobs require a strict linear processing, like many effects in AE, which severely limits the ability to use multiple cores / processors to anything. Moreover, things like access to the linear files in formats based video suite would consist of the issue. And finally, of course, it matters a lot what is happening in your projects. If your film is loading slowly, move it to a faster drive. If it is compressed, decompress / convert. If you use slow effects, replace them with faster commercial third-party plug-ins if you return to clips, speaker of image sequences. The list for the optimisation potential could go on and on, but suffice it to say that none of this implies simply by pushing a magic button or checking a specific option. You must learn these things and refine their experience.

  Mylenium

• Not enough question resources MSDS-driver-TelepresenceServer

  Hi all

  We have a solution with TMS (14.6.2), conductor (XC3.0.3) and GST (4.1 (2.33)).

  Since we went from the TMS to 14.6.2 (from 14.2.1), we get this error:

  tpsfail.PNG

  

  We get this error when we have another time and both get more than 12 participants. We tried to change patterns of conductor (720/30 and no content should be allowed 1/2 screen) to use less than one license per participant but we always get this error.

  Before the tMS upgrade we have no problem with that, we can plan and execute the GST conferences with more than 12 participants, regardless of what quality we choose.

  Best regards

  David.

  There should be a '1280 x 720 p 5 fps' option under the quality of the scrollable content.

• Desktop\SharedDocs is not accessible. You are not allowed to use this network resource. Not enough server storage is available to process this command.

  \\XXXDesktop\SharedDocs is not accessible. You are not allowed to use this network resource. Contact the administrator of this server to find out if you have the permission to access. Not enough server storage is available to process this command.
  I got the above message when I tried to access my room servert pc (XP Pro with Service Pack 3) from another pc Client (XP Home Edition with service pack 3) on a network share. I see all class document & readers who share in my network places on both PCs.
  There is no problem when I have access to XP Home Edition of XP Pro. I heard the pc installed with Acronis True Image to give to this question. But my two PCs are installed with it. Any solution.
  What I've tried so far on my pc (XP Pro):
  1. click on start, run, type regedit, and then click OK.
  2. Locate and double-click the following registry subkey:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa
  3. on the right side, double-click restrictanonymous setting.
  4. make sure that that the value in the value data box is set to 0, and then click OK_ (why the default value is 0. I change it to 1, but always the same)
  5. close the registry editor.
  6. restart the computer.
  I also tried to enable the allow anonymous enumeration of SAM accounts and shares on XP Pro (default value is Disable).
  File and printer sharing exception is enabled in firewall. Don't have a firewall part 3

  The two guest account are capable of Simple file sharing in XP Pro box checked also checked.

  Hello

  Please visit the following link.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-networking/three-computers-networked-fine-then-suddenly-the/3976b554-bb9c-4920-881f-38eb64480ca7

• This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system (Code 12)

  Guys, I have a problem. So, my laptop has 2 graphics cards, an integrated course of the Intel HD graphics (which works perfectly) and the other being the dedicated Nvidia graphics (Nvidia GeForce 940 m). Until 2 days ago, everything was going well and running.

  I have the application experience GeForce and it prompted me that there is a new driver update should I download. He started to install then after rebooting to complete the installation, it failed. I checked my device manager and saw a yellow exclamation under under my Nvidia graphics card (remember, my laptop has two graphics cards: Nvidia graphics card and Intel HD graphics that works correctly). I immediately checked the details, and he said:

  "This device cannot find enough free resources that it can use. (Code 12) »

  "If you want to use this device, you will need to disable one of the other devices on this system."

  This seemed very strange, because it was LITERALLY working properly before I was invited about update driver I got, so I don't know what to do - as a matter of fact, literally, I finished this game, Deadpool, with my Nvidia card that I put as the default graphics card, a few hours before , so I don't know why this happened. Any help? I'm looking for a logical answer to this, guys!

  Additional information:

  A few days before this happened, I went to my store local pc and installed an extra 4 gigs of ram on my 4 existing to make 8. Don't know if it's useful, but anyway

  If I pick up my laptop and shake it side by side, I hear a slight rattling noise, and it seems a little loose (I found this out after seeing the error message). The noise seems to come from just below the middle of my keyboard (I'm using a laptop). If for some reason, my Nvidia card is loose? Is this possible?

  I am quite technologically inclined, but not to the extent of removing components and reconstruction cell phones / pc and access the bios and what not. I can only remove/add ram.

  I want to know if its something I am able to fix it because I do not necessarily want to go running and sending my laptop places - only my pc up shop.

  Here is the location of my Nvidia card: PCI Slot 4 (PCI bus 4, device 0, function 0)

  My specs:

  Acer TravelMate p257-MG

  Windows 7 business

  Intel core i5-5200u 2.20 GHz 2.20 Ghz processor

  8.00 GB of ram

  64-bit operating system

  1 t hard drive

  940 m Intel HD graphics 5500 & Nvidia Geforce card

  Just to recap, I get the error on my Nvidia graphics card code, "this device cannot find enough free resources that it can use. (Code 12) ""If you want to use this device, you will need to disable one of the other devices on this system. »

  Thanks in advance!

  Hello

  Thank you for your response.

  I appreciate your time.

  I suggest you run ' Intel Chipset Software Installation Utility ' and check.
  Reference:
  http://www.Intel.com/content/www/us/en/support/software/Chipset-Software/Intel-chipset-software-installation-utility.html

  Please keep us updated.

  Thank you

• XP logon message... system couldn't open session... not enough memory is available to process this command.

  Windows XP has just received the last update.  If a user is logged on cannot pass between users because when do you a pop up and States opening message... "" the system could not log due to the following error: not enough memory is available to process this command "."

  -Have concerts and gigs of free hard disk space
  -Currently 2 GB RAM
  -He just started this
  -The system does not allow more than 1 user at a time to log in now
  -If you try to connect more than 1 user, it displays the error message and cannot connect again, even not the original user, you must restart the system.

  So what's happening?  Is it a mind foopah the latest patch XP?  Why can't connect more than 1 user on?  I used to be able to connect the whole family and switch between users!

  Remove your antivirus (Norton, Bitdefender 2010, etc.) and try to connect again.  It should work.  Then download Microsoft Security essential Microsoft and you shoul be ok.

  Vitin

• Why I see Runtime Error R6016-not enough space for thread data?

  All of a sudden when I try to launch Google Chrome, I get "error R6016-not enough space for thread data? ' like Chrome stops. Plenty of hard disk, disk defragmented, no viruses or malware. Never seen this message before.

  I think you're on the right track to reinstall Chrome... but they have a method of choice for the best results and that the information is here:

  http://support.Google.com/chrome/bin/answer.py?hl=en&answer=111899

  Just FYI, running sfc/scannow won't help, but it will waste your time and you will not be able to determine which file is causing the problem because...

  When sfc/scannow runs successfully, you will see a start and complete message in the Event Viewer log system.

  It can take a long time to run and slow down your system.  When it starts and stops correctly you can only see events like this in the case where the system log viewer:

  Event type: Information
  Event source: Windows File Protection
  Event category: no
  Event ID: 64016
  Analysis of file File Protection Windows has been started.

  Event type: Information
  Event source: Windows File Protection
  Event category: no
  Event ID: 64017
  Windows File Protection file analysis completed successfully.

  There is no information about what he did or what he did not.

  Even if sfc/scannow finds something to do, you will not know about it.

  That's why try again more than a waste of time.

• My slideshow said opening program there is not enough space on I: but I: is an external hard drive. Why is it not open c:

  At the opening of my slide show program he says there is not enough space on I: but I: is an external hard drive. Why is it not open c: I have used before with no problems. Is there a way to force it to open it on my computers built in the hard drive?

  Hello

  1. what Slideshow program do you use?

  2. you try to open a slide show file or the program itself?

  3. If you try to open the file, then where is it?

  4. have you made a recent software or hardware changes to the system?

  If you are trying to oepn the file, then you can try to copy the file to the desktop and check if it helps.

• When I try to use the paint on my computer it says not enough memory or resources

  computer is not enough memory or resources when trying to use paint

  Hello

  1. when it last work very well?

  2 recent changes on your computer?
  3. is this problem only with paint?

  4. what service pack is installed on your computer?

  Method 1:
  If you receive the error message above when opening a bitmap in Microsoft Paint, the only resolution at this time is to open the bitmap file in another program. I suggest you perform the steps to fix:
  a. open an existing bitmap.
  b. in the Image menu, click attributes.
  c. click on default and then click OK.
  d. on the file menu, click Save as and save the bitmap with a new name.
  e. close and restart Paint.

  Method 2:
  If this step does not help then you can perform a System File Checker on your computer and check if it works.

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file.  You can check the link:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  The sfc/scannow command. analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  Once the SFC scan is complete, you can also try running these two commands at the elevated command prompt.
  a. right click on command prompt and open it as administrator
  b. run the two commands regsvr32 /u zipfldr.dll and regsvr32 /i zipfldr.dll

• Removed USB controllers: can not return - "this device cannot find enough free resources that it can use. (Code 12)

  Original title: removed USB controllers: can not return

  Hello

  So today I tried to connect to a printer, and it wouldn't work (separate the issue, I don't want to worry about that now)

  I've seen several messages saying: you need to uninstall the USB controllers in Device Manager and then restart your PC. The pilots would then automatically reinstalled.

  It didn't happen, and now my Dell touch screen does not work. I can miss several other USB controllers too, I uninstalled about 3 of them, but I don't know whether or not it has been reinstalled.

  I currently have:

  -Hub USB generic

  -Enhanced host controller USB Intel (R) 8 series #1-9C 26

  -USB root hub

  -Host controller compatible xHCI USB

  Note that the last of them was a symbol of error on it and reads as follows:

  "This device cannot find enough free resources that it can use. (Code 12)

  If you want to use this device, you will need to disable one of the other devices on this system. »

  Can someone please tell me how much USB controllers I should have and how to save them?

  Thank you very much

  Hi Shalini.

  Thanks for the reply, but if you read through the posts on this thread, I think you will find that it has already been suggested that I do these two things - what I've done many times without result.

  Fortunately, I managed to fix it myself.

  To satisfy your curiosity and help someone else who could see this thread with a similar problem, here are the steps I took finally solve the problem:

  ______________________________________________

  I was always convinced that the problem is basically with the xHCI USB controller that I saw always reported as not working not properly in the device (Code 12) Manager. With this in mind, I set out to see if I could determine what the device was supposed to be in conflict with. I ran msinfo32 and began to examine the conflicts/sharing section. After a while, I decided I could not see anything obviously problematic or direct me to the controller xHCI, so I gave up on that front.

  Well, if I couldn't fix the problem with the current installation, maybe that I could find another way to install the xHCI USB controller that could circumvent the flaw that seems to be caused when windows reinstalls automatically it when restarting after the abduction. So I started trying to learn more about this "xHCI USB controller" - since Googling this term has given no end of problems not related.

  In Device Manager, I found a way to isolate the details of this driver in device (somewhere under the properties I believe) Manager. This has created a custom device showing in view only a select few connects the Manager. I have spent some time in the analysis of these and found the time during which the camera has stopped working properly. Suddenly a pattern emerges. Over and over again, see you the following series of when I was hoping that allowing windows to reinstall automatically the driver would to fix:
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been removed

  [Rebooted PC]

  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been configured
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 had a problem starting.

  Under each newspaper was referring to a driver name, I didn't already had access to: driver name: usbxhci.inf

  Now I got some new information about the xHCI USB controller, I took to Google. After much research (and not find something relevant), I found 2 obscure references to the driver who seemed at least somewhat relevant.
  The first reference has been a post on the forum where someone's USB ports stopped working. very similar problem to mine! There is little of any particular use in the nets, with the exception of the reference to a couple of windows updates: KB 2823516 or KB2822241

  It is not clear exactly what usbxhci.inf capacity was tied to these updates, but I made a note of them and moved.

  Another article contained no mention of specific ports USB not working does not and was centered around a different problem entirely. However, he has mentioned an another windows update: KB2919355-x 64.msu

  This one (as I remember) was clearer on the relationship between the update and changes to the usbxhci.inf file.

  Now, I had three updates which could make changes to usbxhci.inf at one point. With their name on a piece of paper, I started looking through my updates installed to see which ones I had installed. I soon discovered that Ko 2823516 or KB2822241 were not present on my PC, which saved the penalty to guess who would be the right to uninstall first.

  KB2919355 has been installed, and I made the decision to uninstall it, because as far as I knew, this update changed something in usbxhci.inf. After the initial uninstall was completed, but before the mandatory reboot for changes to take effect, I went into Device Manager and removed the xHCI USB... because I was afraid that if the new, "defective" was always present during the reinstallation of the update, it doesn't change anything.

  The device is removed once more, I rebooted the system. He drives for a considerable period, uninstall the update and then seems to have some sort of hitch; declare something in the sense of "we could not complete the operation. Changes to undo. " He stayed like that for a while before the system became operational again and began to "prepare windows. Once it was over, I discovered that my touchscreen and USB ports worked very well.

  Investigation later showed that the compatible USB xHCI host controller was is no longer marked with warnings. In addition, a series of USB controllers appeared that had not been there when the xHCI device was defective. I was also pleased to note that the update of windows for KB2919355 had already been reinstalled without messing up anything.

  _________________________________________________

• ORA-273xx OS OS system error message: not enough space in CAR 11.0.1.7

  Hello world
  
  We have Oracle RAC on HP - UX 11.32 with two knots after a while that one of the nodes had shot and you cannot issue an order until the server is restarted.
  
  
  Here is a log of messages in the queue alerts.
  
  ERRORS
  =======
  Process m00D died, see the trace file
  Boot process failed, error of the battery:
  Errors in the /u01/app/oracle/diag/rdbms/ecmprd/ECMPRD2/trace/ECMPRD2_psp0_9389.trc file:
  ORA-27300: OS dependent operating system: fork failed with status: 12
  ORA-27301: OS Error Message: not enough space
  ORA-27302: an error occurred at: skgpspawn3
  M007 died the process, see the trace file
  
  
  
  Trace file
  ============
  2011-01-18 15:03:19.980
  Boot process failed, error of the battery:
  ORA-27300: OS dependent operating system: fork failed with status: 12
  ORA-27301: OS Error Message: not enough space
  ORA-27302: an error occurred at: skgpspawn3
  
  2011-01-18 15:13:20.135
  Boot process failed, error of the battery:
  ORA-27300: OS dependent operating system: fork failed with status: 11
  ORA-27301: OS Error Message: Resource temporarily unavailable
  ORA-27302: an error occurred at: skgpspawn5
  
  
  
  I think it's the limitation or problem of operating system kernel. no luck that we stuck with bad engineer as we took a week, but no action until now I try now he climbs, we open bu SR.
  
  Anyway any idea that will really help
  
  DB v 11.1.0.7
  
  
  Thank you

  Hello

  See the TechNote MOS:

  * Troubleshooting error ORA-27300 ORA-27301 ORA-27302 [579365.1 ID] *.

  Thank you
  A H E E R X